Search

Blade wear is the critical problem in the operation of multiphase pump. This paper presents a numerical study of the multiphase flow of multiphase pump. The trajectory of particles in the pump is calculated by the discrete phase model. Then, the simulation results are compared with the model test results of the pump to verify the correctness of the simulation method. The results show that the particles in the impeller domain are mainly near the hub, and the particles in the diffuser domain form a agglomerated area in the middle of the flow channel. The average wear rate of the impeller is more affected by the particle size than that of the diffuser. The maximum wear rate of blade surface increases first and then decreases with the increase of particle size. According to the wear data under different particle sizes, the regression model between particle size and wear rate is fitted to predict the wear of mixed transport pump in actual operation. The research results have important reference value for the prediction of the wear performance of the multiphase pump.

During the operation of a reversible pump-turbine, a hump area can easily appear under the pump condition, which will greatly affect the performance of a storage unit, with pressure pulsation being the key factor for the stable operation of a pump-turbine. Therefore, in order to explore the pressure pulsation characteristics of each flow component in the hump area, this paper first compared the full characteristics of the model test under different working conditions, and then it analyzed the pressure pulsation characteristics. By analyzing the pressure pulsation characteristics in the unit’s flow component under different flow rates in the hump area, the pulsation rule of a pump-turbine running in the hump area was revealed. It was found that the peak-to-peak value of the draft tube in the hump area was the smallest under the optimal flow condition, and the peak-to-peak value increased along the flow direction, with the rotor and stator interaction (RSI) effects being continuously enhanced. When away from the runner basin, the influence of RSI gradually weakened after leaving the runner. No low frequency was found in the optimal traffic. The peak-to-peak value of the low flow condition increased compared with the optimal flow condition, and the distribution was not uniform. The main frequency of the whole basin was relatively complex, indicating that the flow of water was unstable in the condition of partial load, resulting in the hump area during the unit operation. The research results can provide a theoretical reference for improving the stability of pump-turbines.

The Rosin–Rammler function is used in this paper to model the diameter distribution of sand particles. It investigates the characteristics of sand distribution and identifies the primary factors contributing to wear on flow components in a blade-type multiphase pump, considering varying particle sizes. The result of research shows that the blade head of the impeller and the middle section of the flow passage in the diffuser domain represent primary areas prone to sand particle accumulation. The concentration of sand particles within the diffuser surpasses that within the impeller, yet wear severity and extent are more pronounced in the impeller domain compared to the diffuser domain. Meanwhile, the movement trajectory of sand particles is linked to both shear flow and vortex flow. The wear of the front section of the impeller blade is more severe than the second half. On the pressure surface of the blade, particle Reynolds number emerges as a primary factor influencing wear, while on the suction surface, sand particle concentration plays a dominant role in determining wear. The particle concentration in the diffuser domain is the primary factor influencing wear on both the suction and pressure surfaces. The wear rate in the impeller is primarily influenced by the sand particle Reynolds number, whereas the wear rate in the diffuser domain is affected by a combination of sand particle diameter, sand particle concentration, and sand particle Reynolds number. The research findings possess significant engineering value in terms of enhancing the operational lifespan of multiphase pumps.

Unstable flow in a pump-turbine can cause pressure pulsation, and the resulting vibration deteriorates the stability and operating safety of the unit. This study conducted three-dimensional numerical calculations of the overall flow passage of a pump-turbine with splitter blades under the small guide vane opening, and the unsteady flow characteristics of the turbine were investigated. The results showed that the pressure fluctuation was more severe at lower head operating conditions with lower efficiency, especially in the vaneless area (the runner blade passages). Under the lower head condition, the proportion of 12 times the rotational frequency (12 f/fn) increased in the vaneless area, and the amplitude of 1 f/fn as well as 2 f/fn became larger in the runner blade channel, with more space occupied by vortices and reflux areas. A spiral vortex rope formed in the draft tube, increasing the proportion of 0.4 f/fn and 0.7 f/fn pressure pulses.

The internal flow of a pump turbine is unstable in part-load pump mode for small guide-vane openings, and the strong vibration caused by pressure pulsation is related to the safe and stable operation of the unit. A pump turbine with a six-splitter-blade runner was chosen for unsteady simulation analyses. A standard k-epsilon turbulence model was adopted to study the unsteady flow and pressure pulsation in part-load pump mode. The predicted results show that the flow in the draft tube and the runner with splitter blades was relatively stable and the flow of the blade-to-blade channel was symmetrical. When the inlet and outlet velocity distribution of the vanes was not uniform, a vortex began to form in the stay-vane domain. The reason for this vortex formation is explained, and it is pointed out that the existence of the vortex and backflow leads to uneven velocity distribution. The unsteady calculation results showed that the pressure-pulsation peak-to-peak amplitudes in the vaneless area and guide vanes were much higher than those of other monitor points because of rotor–stator interference between the rotating runner and the vanes. In addition, the pulsation characteristics of the monitor points at different circumferential positions in the vaneless region were quite different. In the vaneless area, the velocity gradient along the circumferential direction was very large, and there was a phenomenon of backflow. Also, the pressure pulsation was 0.2 times that of the runner rotational frequency, and the blade-passing frequency was a third-order frequency. At the outlet of the guide vane, the pressure pulsation was mainly of a low frequency with a complex vortex flow. Finally, the pressure pulsation began to decrease rapidly in the stay-vane region.

The sediment erosion of Pelton turbine components is a major challenge in the operation and development of high-head water resources, especially in mountainous areas with high sediment yield. In this paper, a study using numerical simulation was conducted with different sediment particle sizes in the fine sand range. And the erosion mechanism of the Pelton turbine injector was analyzed. The Eulerian Lagrange method was adopted to simulate the gas–liquid–solid flow. The Mansouri’s model was applied to estimate the injector erosion. The predicted erosion results were in accord with field erosion photographs. In particular, the asymmetrical erosion distribution on the needle surface was physically reproduced. With the sediment particle size increasing from 0.05 mm, the needle erosion rate decreased, while the nozzle casing erosion rate increased dramatically. In order to clarify this tendency, the characteristics of the three-phase flow were analyzed. Interestingly, the results show that with the rise in particle size, the separation of particles and water streamlines became more serious in the contraction section of the nozzle mouth. Consequently, it caused the enhancement of erosion of the nozzle surfaces and weakened the erosion of the needle surfaces. Significant engineering insights may be provided for weakening Pelton injector erosion with needle guides in the current study.

Marine environment provides a basic space for human survival and social sustainable development. The study of tribological problems and mechanism of marine engineering materials in the sea extreme environment has become one of key technologies to be developed urgently in the field of marine engineering. This review summarizes and analyzes the tribological research of key friction materials in marine environment, focuses on tribological properties of ceramic, polymer and metal, emphatically introduces the current situation and development trend of tribological research in marine environment, such as metal and metal pairs, ceramics and metal pairs, polymers and metal pairs, polymers and ceramic pairs, and aims to provide a tutorial reference for the selection and application of friction pairs of marine engineering equipment.

esalination represents an effective method for alleviating water scarcity, applying algorithmic techniques to predict the performance of reverse osmosis (RO) desalination plants, Modified Grey Wolf Optimizer (MGWO) based Artificial Neural Networks (ANN) can predict the performance of membrane distillation (MD) equipment. Four experimental inputs are selected: feed salt concentration(35–140 g/h), feed flow rate(400–600 L/h), evaporator inlet temperature (60–80 ℃), and condenser inlet temperature (20–30 ℃). The permeate flux (L/h m²) is selected as the experimental output. Ten prediction models were proposed and compared with the existing models (ANN, WOA-ANN, and GWO-ANN). The results showed that the MGWO-ANN model-5 showed the best regression results: R² = 99.3 %, mean square error (MSE)= 0.004. This model outperformed the existing ANN model (R² =98.8 %, MSE=0.060), WOA-ANN model (R² =99.1 %, MSE=0.005) and GWO-ANN model (R² =98.9 %, MSE=0.007). Model-5 has a single hidden layer (H=1), 13 hidden nodes (n = 13), 10 search agents (SA=10), and 75 %− 20 %− 05 % dataset division. Its residual error is within acceptable limits (spanning −0.1 to 0.2). Optimizing the number of hidden layer nodes (n) and the number of search agents (SA) can improve the training efficiency and prediction accuracy of the model, and the MGWO-ANN model is capable of more accurately predicting the performance of desalination plants. [ABSTRACT FROM AUTHOR]

Due to the irregular change of gas void fraction (GVF) in multiphase pumps, the pressure distribution in the pump is often uneven, which leads to the formation of low-pressure area and thus the occurrence of cavitation. In order to study the gas phase and cavitation distribution in the impeller region of a multiphase pump under different cavitation stages and GVF conditions, this study used numerical calculations as the main method and experimental verification as a secondary method to investigate the cavitation phenomenon in the pump under different stages and GVF conditions. The results showed that at different stages, both the volume fraction and the covering area of the gas phase were reduced to a certain extent with the increase in blade height, and the distribution law of the gas phase on the blade changed with the development of the cavitation stage, especially on the blade surface. At different GVFs, cavitation first occurred at the inlet of the blade SS and then extended along the blade streamline from the inlet to outlet, with the volume fraction and distribution of cavitation gradually increasing and then extending to the blade PS. The results showed that the presence of the gas phase inhibited the development of cavitation in the multiphase pump to some extent, and the cavitation performance of the multiphase pump was better in the presence of the gas phase than in pure water conditions. The results of this study provide a theoretical basis for improving the cavitation performance of multiphase pumps.

In this paper, the gas-liquid flow is comprehensively analyzed under different inlet gas void fractions, and the effect of tip leakage vortex (TLV) on the gas flow pattern in multiphase pumps is revealed. The results show that the gas flow pattern in an impeller is closely related to the centrifugal force, low-pressure region, and vortex motion. Most gas is present near the hub and suction surface of the blade as well as in the TLV. The two- and three-dimensional spatiotemporal evolution of the gas is presented, and the gas motion during the inception, development, and dissipation of TLV is revealed. It is reflected that the gas volume fraction is the highest at the TLV core and gradually weakens along the radial direction with the vortex core at the center. Additionally, the TLV energy dissipation is closely related to the gas and pressure difference, and strong energy dissipation occurs in the jet-wake flow.

When the multiphase pump is running, the internal medium often exists as bubble flow. In order to investigate the bubble occurrence characteristics in the pressurization unit of the multiphase pump more accurately, this paper couples computational fluid dynamics (CFD) with a population balance model (PBM) to investigate the bubble size distribution law of the multiphase pump under different operating conditions, taking into account the bubble coalescence and breakup. The research shows that the mean bubble size in the impeller domain gradually decreases from 1.7013 mm at the inlet to 0.6179 mm at the outlet along the axis direction; the average bubble diameter in the diffuser domain fluctuates around 0.60 mm. The bubbles in the impeller region gradually change from the trend of coalescence to the trend of breakup along the axial and radial directions, and the bubbles in the diffuser tend to be broken by the vortex entrainment. The bubble size development law is influenced by the inlet gas volume fraction (IGVF) and the rotational speed, showing a more obvious rule, where the gas phase aggregation phenomenon enhanced by the increase in IGVF promotes the trend of bubble coalescence and makes the bubble size gradually increase. The increased blade shearing effect with the increase in rotational speed promotes the trend of bubble breakup, which gradually reduces the size of the bubbles. In addition, increasing the bubble coalescence probability is a key factor leading to changes in bubble size; the bubble size development law is not very sensitive to changes in flow, and the bubble size is at its maximum under design conditions. The research results can accurately predict the performance change of the multiphase pump and provide technical guidance for its safe operation and optimal design.

Dredge pumps are usually operated at part-load conditions, in which the low-solidity centrifugal impeller could experience large internal energy dissipation, related to flow separation and vortices. In this study, SST k-ω and SAS-SST turbulence models were used, in steady and unsteady simulations, for a low-head centrifugal pump with a three-bladed impeller. The main focus of the present work was to investigate the internal energy dissipation in rotating an impeller at part-load operating conditions, related to flow separation and stall. The unsteady nature of these operating conditions was investigated. Performance experiments and transient wall pressure measurements were conducted for validation. A methodology for internal energy dissipation analysis has been proposed; and the unsteady pressure fluctuations were analyzed in the rotating impeller. The internal power losses in the volute and the impeller were mostly found in the centrifugal pump. The rotating stall phenomenon occurred with flow separation and detachment at the part-load operating condition, leading to a dissipation of the internal energy in the impeller. The rotating impeller experienced pressure fluctuations with low frequencies, at part-load operating conditions, while in the design operating condition only experienced rotating frequency.

After long-term operation, the material loss due to slurry erosion often leads to significant changes in the impeller geometry. This change can, in turn, affect the flow characteristics and the erosion mechanism in a centrifugal pump. To investigate this matter, we consider two geometric models based on a prototype stainless steel impeller, which failed due to huge erosion problems from the pulp slurry. These two models are different in the degree of wear, with one model at the pre-erosion stage and the other with worn blades. For both models, the flow characteristics have been obtained in the Eulerian reference frame by means of the SST k-ω model. Then, in order to determine the erosion patterns, the particles have been tracked in the Lagrangian reference frame. In this way, the influence of the flow characteristics on the erosion patterns has been analyzed. Results show that the geometric variations greatly affect the flow characteristics, and consequently the erosion patterns. Particularly, it has been found that the clearance flow plays a significant role in defining erosion characteristics, such as erosion distribution, areas, and rates. Interestingly, the simulation results for current study show that the erosion rates after long-term operation greatly decrease near both the outlet edge and the blade bottom. It follows also that for accurate erosion predictions, these geometric variations have to be considered in the numerical model. This paper provides a better understanding of the complex erosion mechanism in centrifugal pumps, which can help to reduce the wear in future designs.

Clearance flows in the sidewall gaps of centrifugal pumps are unsteady as well as main flows in the volute casing and impeller, which may cause vibration and noise, and the corresponding pressure fluctuations are related to the axial clearance size. In this paper, unsteady numerical simulations were conducted to predict the unsteady flows within the entire flow passage of a centrifugal pump operating in the design condition. Pressure fluctuation characteristics in the volute casing, impeller, and sidewall gaps were investigated with three axial clearance sizes. Results show that an axial clearance variation affects the pressure fluctuation characteristics in each flow domain by different degree. The greatest pressure fluctuation occurs at the blade pressure surface and is almost not influenced by the axial clearance variation which has a certainly effect on the pressure fluctuation characteristics around the tongue. The maximum pressure fluctuation amplitude in the sidewall gaps is larger than that in the volute casing, and different spectrum characteristics show up in the three models due to the interaction between the clearance flow and the main flow as well as the rotor-stator interaction. Therefore, clearance flow should be taken into consideration in the hydraulic design of centrifugal pumps.

This paper presents a multi-objective optimization procedure for bidirectional bulb turbine runners which is completed using ANSYS Workbench. The optimization procedure is able to check many more geometries with less manual work. In the procedure, the initial blade shape is parameterized, the inlet and outlet angles (β1, β2), as well as the starting and ending wrap angles (θ1, θ2) for the five sections of the blade profile, are selected as design variables, and the optimization target is set to obtain the maximum of the overall efficiency for the ebb and flood turbine modes. For the flow analysis, the ANSYS CFX code, with a SST (Shear Stress Transport) k-ω turbulence model, has been used to evaluate the efficiency of the turbine. An efficient response surface model relating the design parameters and the objective functions is obtained. The optimization strategy was used to optimize a model bulb turbine runner. Model tests were carried out to validate the final designs and the design procedure. For the four-bladed turbine, the efficiency improvement is 5.5% in the ebb operation direction, and 2.9% in the flood operation direction, as well as 4.3% and 4.5% for the three-bladed turbine. Numerical simulations were then performed to analyze the pressure pulsation in the pressure and suction sides of the blade for the prototype turbine with optimal four-bladed and three-bladed runners. The results show that the runner rotational frequency (fn) is the dominant frequency of the pressure pulsations in the blades for ebb and flood turbine modes, and the gravitational effect, rather than rotor-stator interaction (RSI), plays an important role in a low head horizontal axial turbine. The amplitudes of the pressure pulsations on the blade side facing the guide vanes varies little with the water head. However, the amplitudes of the pressure pulsations on the blade side facing the diffusion tube linearly increase with the water head. These results could provide valuable insight for reducing the pressure amplitudes in the bidirectional bulb turbine.