Search

Waste carbon fibers as reinforcing elements in construction materials have recently gained increasing interest from researchers, providing outstanding strength performance and a lower environmental footprint compared to virgin fibers. Combination with cement-free binders, namely alkali-activated materials, is becoming increasingly important for sustainable development in the construction industry. This paper presents results relating to the potential use of waste carbon fibers in alkali-activated mortars. The waste carbon fiber fraction utilized in this research is difficult to integrate as reinforcement in ceramic–cementitious matrices due to its agglomerated form and chemical inertness. For this reason, a nanoceramic coating pretreatment based on nanoclay has been implemented to attempt improvements in terms of deagglomeration, dispersibility, and compatibility with alkali-activated materials. After chemical–physical and microstructural analysis on the nanoclay-plated fibers (including X-ray diffraction, IR spectroscopy, contact angle measurements, and electron microscopy) mortars were produced with four different dosages of treated and untreated waste fibers (0.25 wt.%, 0.5 wt.%, 0.75 wt.%, and 1 wt.%). Mechanical tests and fractographic investigations were then performed. The nanoclay coating interacts compatibly with the waste carbon fibers and increases their degree of hydrophilicity to improve their deagglomeration and dispersion. Compared to the samples incorporating as-received fillers, the addition of nanoclay-coated fibers improved the strength behavior of the mortars, recording a maximum increase in flexural strength of 19% for a fiber content of 0.25 wt.%. This formulation is the only one providing an improvement in mechanical behavior compared to unreinforced mortar. Indeed, as the fibrous reinforcement content increases, the effect of the nanoclay is attenuated by mitigating the improvement in mechanical performance.

Utilising recycled brick aggregate in cementitious mixtures can decrease the overdependency on limited natural resources and improve the sustainability of concrete. This paper presents a potential solution to lower the amount of waste being landfilled and increase the sustainability of 3D concrete printing technology by combining low-carbon ternary blended cement with recycled aggregates. Hence, the effect of incorporating two types of recycled brick aggregate - clay brick (CBA) and engineering brick (EBA) on the properties of 3D printable ternary blended cement were investigated. The natural aggregate in a pre-existing 3D printable blend was substituted by up to 50 wt.-% with two varieties of recycled brick aggregates available throughout Europe. The recycled brick aggregates underwent characterisation to determine their properties. The fresh property evaluation using the green strength test was used to assess the effect of aggregate replacements on the mixture's shape stability. The mechanical performance of mixtures containing CBA and EBA, both cast and 3D printable mixes, was evaluated and compared to that of the control sample. The results indicated that incorporating recycled brick aggregate enhances green strength and Young's modulus significantly. Mechanical strength performance showed significant enhancement when incorporating RBA, which reached up to 67% and 55% for both cast and 3D printing methods, respectively. The suitability of the developed mix formulations for 3D printing was assessed by printing cylindrical objects.

This study explores the potential of waste brick and geo-cement aggregates as substitutes for natural sand in alkali-activated materials (AAMs) for mortar production. With a focus on achieving net-zero construction and mitigating environmental impact, the study replaces Portland Cement (OPC) and virgin aggregates with waste materials and by-products. The investigation evaluates the substitution of sand (up to 100 % by weight) in AAMs with waste brick aggregates (WBA) and waste geo-cement aggregates (WGA) obtained from demolished construction and research lab waste, respectively. The research methodology involves assessing mechanical, durability, and microstructure properties to assess the performance of the developed AAMs with waste aggregates. Notably, AAM composites containing waste brick and geo-cement aggregates surpass natural aggregate composites in terms of mechanical strength, water absorption, freeze-thaw resistance, acid ingress, and chloride attack. The 7-day 50 % waste brick mixture achieved a maximum compressive strength of 61 MPa, while a 70 % waste geo-cement mortar mixture attained a maximum flexural strength of 12 MPa. Combinations, whether comprising waste brick or geo-cement mortar aggregates, demonstrate compressive strengths well over 40 MPa, rendering them suitable for heavy load-bearing structures. The 50 % waste geo-cement mortar mixture stands out with the lowest water absorption rate of 6 % and the least compressive strength loss of 13 % after the freeze-thaw test, with reductions of 6 % and 18 %, respectively, compared to the control. Additionally, 100 % waste brick AAMs exhibit the lowest compressive strength loss after chloride and acid attack tests, with reductions of 13 % and 2.5 %, respectively. When compared to all other mixtures, the 50 % waste brick aggregates mortar mixture obtained the best overall performance. The composites developed in this study affirm their suitability for use in heavy-load structural components, showcasing favourable mechanical and durable properties. These findings underscore the need for additional exploration in this direction to advance sustainable construction practices.

This study investigates the printability of one-part brick powder-based alkali-activated materials (AAMs) containing end-of-life brick particles as aggregate. The novel formulation showcases promise for 3D printing of small to medium-sized building blocks, reminiscent of a Lego-type system, capitalising on the rapid setting time inherent to one-part AAMs. The effect of replacing up to 50% by weight of natural aggregate with brick aggregate on the fresh properties of brick powder-based alkali-activated materials, including slump measurements, flowability, setting time, open time and green strength were investigated. In addition, the flexural and compressive strength of the 3D printed mixtures were determined and compared to those of cast specimens. The buildability and microstructure were also examined. The results showed that incorporating high porous and rough brick aggregate to replace natural aggregate is beneficial in improving the mixtures’ slump, which is essential for retaining the shape of the printed layers. However, it decreased the flowability, setting time and open time when incorporating up to 50% brick aggregate. The green, flexural and compressive strengths were increased with increasing brick aggregate content up to 50% due to enhancing interlock between the binder and brick aggregate, and the better compaction because of the absorption properties of brick aggregate. The mechanical results revealed the better performance of 3D printed specimens than the cast specimens. Moreover, the incorporation of brick aggregate enhanced the buildability of the mixtures showcasing their potential in advancing 3D printing capabilities.

One-part alkali-activated materials (AAMs) can preserve natural resources and lower embodied carbon of the built environment by accommodating various wastes, industrial by-products, and end-of-life materials in their composition. This study investigates the feasibility of using end-of-life bricks in two physical states, powder and aggregate, to partially replace fly ash precursor and natural aggregate in AAMs, respectively. The mechanical characteristics, microstructure, water absorption, freeze-thaw and fire resistance of the modified AAMs were evaluated. The effect of adding different ratios of nano graphite platelets was also investigated. Results showed that brick-based one-part AAMs can achieve mechanical properties, pore structure, water absorption and freeze-thaw resistance comparable to fly ash-based AAM while having 65% better fire resistivity. Incorporating bricks as aggregate resulted in a maximum improvement of 17% and 27% in the AAMs' compressive and flexural strength levels, respectively, and a general enhancement in the freeze-thaw resistance with showing no reduction in compressive strength after exposure to elevated temperature. Incorporating 0.1 wt% nano-graphite further enhanced flexural strength by 30%, decreased water absorption by 18% and improved freeze-thaw resistance compared to the mix without nano-graphite. Moreover, adding up to 0.5% nano-graphite enhanced the fire resistivity of the composite, allowing it to exhibit 19% better strength performance than before exposure.

3D printing is a developing technology that has the ability to use different materials to produce concrete elements with complex shapes. The utilization of geopolymers or alkali-activated materials (AAMs) in 3D printing is receiving significant interest due to the environmental benefits of replacing ordinary Portland cement (OPC). The use of solid activators to produce a one-part geopolymer can help the broader use of geopolymers at large scales, as the corrosive, viscous, and hazardous liquid activators used in two-part geopolymers do not present a feasible large-scale solution for this technology. This paper reviews the 3D printable one-part geopolymers, their compositions, and the effect of different precursor compositions, activator content, and different admixtures on the fresh and hardened properties of the mixtures. The environmental impact and cost assessment of one-part geopolymers produced by conventional and 3D printing methods are also discussed and compared to OPC and two-part geopolymers. This review concluded that one-part geopolymers are easier to mix and use than two-part geopolymers and have a lower carbon footprint than two-part geopolymers and OPC concrete. However, one-part geopolymers may not be as strong as two-part geopolymers, but they are still better than OPC.

The rapid development in 3D printing applications requires exploring a sustainable printable mixture to decrease the environmental impact induced by the existing Ordinary Portland Cement (OPC) mixtures and enable 3D printing technology to reach its peak efficiency. The high-volume substitution of OPC with supplementary cementitious materials (SCMs) is of significant interest as a promising solution for developing low-carbon feedstock for 3D printing. Yet, those materials share the problem of limited availability. The combination of limestone and calcined clay could be a promising alternative, offering various benefits, including replacing OPC in high ratios. This paper reviews 3D printable limestone calcined clay cement (LC3) mixtures, compositions, and chemical behaviour. The effect of different sand-to-binder ratios, additives content, OPC replacement levels, clay grade and calcination, and admixtures on the fresh, hardened and printing properties of the 3D printed mixtures are critically discussed. The environmental impact and production cost of the LC3 system compared to OPC and other systems are also critically evaluated along with the applications, future directions and research gaps in this field. The findings of this review show that 3D printed LC3 has a similar hardened performance and better microstructure than OPC system. Moreover, cast LC3 system has 30–50% lower environmental impacts depending on the replacement level and better economic feasibility than OPC. Therefore, making it a suitable feedstock for the innovative manufacturing technology of 3D printing.