Search

Since the Party Central Committee has explicitly requested the running of excellent ideological and political theory courses, the teaching methods of ideological and political theory courses have become a major topic of discussion in academic circles. A gap remains between the current teaching methods of ideological and political theory courses and those in the new era. In order to improve the nurturing effect of key courses, it is necessary to study the basic logic of its effectiveness enhancement from the perspective of practice. In the new era, it is essential to take the spirit from the series of important speeches of the Party and national leaders on ideological and political theory courses as guidance, draw on the effective teaching ideas of Comenius that reflect “fun,” “convenience,” and “thoroughness,” closely combine the teaching practice, as well as select and apply the teaching methods based on the concept of three “combinations” and two “innovations,” i.e., combining students, teachers’ teaching styles, and teaching contents; and innovating and practicing the integrated teaching method of diversified integration as well as the new teaching method of media technology-integrated smart classroom.

A novel solar assisted heat pump (SAHP) system for in-bin grain drying was proposed to solve the problems of poor uniformity and long drying time of grain in depot with higher initial water content in high grain piles. The effects of different operational parameters on the drying performance were numerically and experimentally investigated. The experimental results indicated that the thermal efficiency of the solar collector and the COP of the heat pump reached 63% and 5.03 under given conditions. The average heating capacity of the SAHP system was 130.2 kW, consistent with the simulation results under a typical sunny day in winter. The average water content of 3,760 tons of grain dropped from 12.9% to 12.5% after 42 h of drying. The specific moisture extraction rate of the proposed system and the exergy efficiency of the grain bin were 1.934 kg/kWh and 40.27%, respectively. The operating cost of SAHP grain drying decreased from 5.57 $/t to 1.43 $/t compared with the grain drying machine for the same drying weight. The daily drying capacity increased from 166 t/d to 334 t/d compared with the mechanical ventilation drying for the same water content reduction rate. This investigation provided guidance for expanding future researches on the SAHP system applied for in-bin grain drying.

Isothermal chemical conversion of biomass pellets under the atmospheres of Ar, CO2 and O2 were conducted in this study to explore the effects of atmosphere and temperature on the gaseous releasing process and kinetics, and the structure of the solid char/ash products. Results showed that the gas production was promoted while the solid yield was decreased with the raising temperature. The CO2 reaction with char during gasification process mainly happened after 800 °C that the CO formation lasted for a longer time than pyrolysis. The surface area of char under CO2 atmosphere was increased to 215.57 m2/g with the increased temperature to 800 °C, but it was sharply reduced to 5.10 m2/g when the temperature further raising to 900 °C due to the destroyed carbon skeleton. The CO2 formation was largely promoted with a low activation energy of 11.98 kJ/mol during O2 oxidation process. Compared with the crystal structure of solid residues obtained under Ar and CO2 atmospheres, O2 oxidation process resulted in more complex crystal peaks with the main compositions of SiO2, K2SO4, and CaO. This study should be helpful to further understand the thermal conversion of biomass in a complex reaction atmosphere.

Biorefinery systems are playing pivotal roles in the technological support of resource efficiency for circular bioeconomy. Meanwhile, artificial intelligence presents great potential in handling scientific tasks of high-dimensional complexity. This review article scrutinizes the status of machine learning (ML) applications in four critical biorefinery systems (i.e. composting, fermentation, anaerobic digestion, and thermochemical conversions) as well as their advancements against traditional modeling techniques of mechanistic approach. The contents cover their algorithm selections, modeling challenges, and prospective improvements. Perspectives are sketched to further inform collective efforts on crucial aspects. The multidisciplinary interchange of modeling knowledge will enable a more progressive digital transformation of sustainability efforts in supporting sustainable development goals.

Thermal analysis of data centers is in urgent need to ensure that computer chips remain below the critical temperature while the energy consumption for cooling can be reduced. It is difficult to obtain detailed hotspot locations and temperatures of chips in large data centers containing hundreds of racks or more by direct measurement. In this paper, a multi-scale thermal analysis method is proposed that can predict the temperature distribution of chips and solder balls in data centers. The multi-scale model is divided into six scales: room, rack, server, Insulated-Gate Bipolar Transistor (IGBT), chip and solder ball. A concept of sub-model is proposed and the six levels are organized into four simulation sub-models. Sub-model 1 contains Room, Rack and Server (RRS); Sub-model 2 contains Server and IGBT (SI); Sub-model 3 contains IGBT and Chip (IC), and Sub-model 4 contains Chip and Solder-ball (CS). These four sub-models are one-way coupled by transmitting their results as boundary conditions between levels. The full-field simulation method is employed to verify the efficiency and accuracy of multi-scale simulation method for a single-rack data center. The two simulation results show that the highest temperature emerges in the same location. The Single-rack Full-field Model (SRFFM) costs 2.5 times more computational time than that with Single-rack Multi-scale Model (SRMSM). The deviation of the highest temperature of chips and solder balls are 1.57°C and 0.2°C between the two models which indicates that the multi-scale simulation method has good prospect in the data center thermal simulation. Finally, the multi-scale thermal analysis method is applied to a ship data center with 15 racks.

Building-integrated photovoltaics is a crucial technology for developing zero-energy buildings and sustainable cities, while great efforts are required to make photovoltaic (PV) panels aesthetically pleasing. This places an urgent demand on PV colorization technology that has a low impact on power conversion efficiency (PCE) and is simultaneously mass-producible at a low cost. To address this challenge, this study contributes a colorization strategy for solar PVs based on short-range correlated dielectric microspheres

This paper describes the development of a novel CPC (compound parabolic collector) evacuated tube solar collector, using a medium-temperature selective coating. The medium-temperature selective coating was obtained by co-sputtering titanium and aluminum targets. The absorptance and the thermal emittance of the heat treated coating is 0.95, and 0.04 at 80℃ respectively. The collector was optimized, using a manifold of copper U-tube with anti-oxidized coating and aluminum fin. An anti-reflection layer is added on the cover glass tube, and non-flash getter are used for maintaining the vacuum of the collector tubes. Thermal test results shown that the instantaneous efficiency based on gross area ηG can reach 0.46 at the temperature of 150℃ and the normalized temperature difference Tm* is 0.13 [(m2-°C)/W]. The experimental steam system application showed that the novel CPC solar collector can produce steam from water with temperatures about 108–145 °C during sunny days. It was also shown that the thermal performance of the solar collector did not degraded significantly.

Evacuated tube solar collector (ETSC) is widely used for domestic and industrial applications. Using reflective coating in an ETSC to realize concentration is a method to heighten the thermal efficiency due to solar irradiation could be reflected by the coating on the lower half of the outer glass tube and concentrated to the eccentric inner absorber. In this paper, an evacuated tube solar collector with inner concentrating (ETSC-IC) by reflective coating was proposed and fabricated. A series of experimental tests of the ETSC-IC was conducted to investigate the thermal performance. In addition, the mathematical model of the novel collector with inner concentrating was developed, and the structural parameters of the inner reflective concentrating evacuated tube, including the coating angel and the eccentric distance, have been analyzed. The optical and thermal analysis revealed that the best coating angle of the evacuated tube was 180°, and the thermal performance of the ETSC-IC enhanced with the increase of the eccentric distance under the best coating angle. The thermal efficiency of the ETSC-IC could reach 0.65 to 0.72 on the condition that the solar irradiation was around 950 W/m2 and the temperature of inlet water varied between 45 °C and 70 °C, and the ambient temperature was 31.2 °C. The thermal efficiency of the ETSC-IC was improved by approximately 10% compared with the conventional evacuated tube due to the enhanced irradiation concentrating and the reduction of heat loss caused by the coating on the outer glass tube.

Solar-powered LiBr absorption cooling system is of potential in the application of air-conditioning. A LiBr-H2O concentration difference cold storage system driven by vapor compression heat pump was proposed. This cold storage process is not affected by the environmental conditions, since the main energy input is low price electricity at night. The experimental results show that the energy storage density (ESD) can reach 77.8 kWh/m3 and the energy storage coefficient of performance (ESCOP) is 2.81 with low heat loss. The ESCOP means the energy stored in the cold storage process divided by the total electricity consumption in the absorption and heat pump subsystem. The heat transfer in the condenser of the absorption subsystem approximately equals that in the evaporator of the heat pump, and the electricity consumption of the circulating pump in the absorption subsystem is low. Therefore, the value of ESCOP should be slightly lower than the COP of the heat pump system but for higher than 1. These results indicate the feasibility of improving the system efficiency, the operation cost, and long term operation of the solar air conditioning system by coupling the absorption and vapor compression cooling cycles. Finally, the influence of working parameters on the system performance is discussed based on the experimental and simulation analyses. The energy balance between the absorption cycle and the heat pump cycle in the cold storage system is analyzed. It is found that the coefficient of performance of the heat pump (COPele,HP) and ESCOP increase with a low initial LiBr-H2O solution concentration. The ESCOP decreases by 34.4% when the initial concentration increases from 52% to 57%. The average ESD increases to 140.2 kWh/m3 with a concentration difference of 8%. Based on the experiment results, the payback period of the proposed system is estimated as 2.4 years comparing with the traditional LiBr-H2O absorption system.

Borehole heat exchanger (BHE) is a promising method for extracting heat from the deep geothermal energy which has been widely used for residential heating in high latitude areas. The solar assisted photovoltaic/thermal (PV/T) heat pump could convert solar energy into useful heat efficiently, and could be further used to heat water from the BHE to a higher temperature level. In this paper, a residential heating system using BHE coupled with solar assisted PV/T heat pump is therefore proposed with further performance analysis. The simulation results show that a larger mass flow rate could increase the BHE's heat extract capacity but also increase the flow resistance and pump power under nominal conditions. The circulating water would not extract heat from rock-soil if the inlet temperature exceeds 48.5 °C when mass flow rate is 12 kg/s. Furthermore, the maximum water temperature from this hybrid system could reach 40.8 °C while the solar fraction is 67.5% when the area of PV/T module is 1000 m2, solar irradiation is 600 W/m2 and depth of the BHE is 2500 m. In the meantime, the heating COP of this hybrid system could reach 7.4 and the system could operate independently without power input from electrical grid.

Singapore’s first multi-source high-flux solar simulator (HFSS) that comprises an array of seven 4-kWe xenon short-arc lamps close-coupled with ellipsoidal reflectors is designed, constructed, and characterized. An indirect mapping system that consists of a water-cooled Lambertian target, a CMOS camera, and a heat-flux gauge is adopted herein to experimentally characterize the performance of the developed HFSS. A calibration constant of 192.8 ± 9.6 kW m−2 (GS µs−1)–1 is determined and used to transform the raw-flux maps with grayscale values to the absolute-flux maps. Utilizing a series of flexible and precise adjusters, the variability of ± 1 mm in the x- and y-directions of the peak flux points of the radiation modules is measured. A peak flux of 7740 kW m−2 is measured for the sum of all 7 radiation modules. Average radiative fluxes of 4191 kW m−2 and 2933 kW m−2 can be observed from circular target areas of O40 mm and O60 mm, respectively, associated with promising electricity-to-target transfer efficiencies of 18.8% and 29.6%. A Monte Carlo ray-tracing (MCRT) model is calibrated by the experimental data. Based on the minimum root-mean-standard deviation between the measured and simulated results of the radiative power on the target, the optimal parameters of the MCRT model include the arc radius of 3.4 mm and the reflector surface error of 1.1 mrad.

Direct expansion solar assisted PVT (photovoltaic/thermal) heat pump is a combination of PVT technology and heat pump technology, which can improve the comprehensive conversion efficiency of solar energy, and it is suitable for solar heating applications. In this paper, the efficiency factor of direct expansion PVT module employing roll-bond panel has been theoretically derived, modified, and validated by experimental results. Moreover, the efficiency factor could be used to design, evaluate, and optimize the thermal performance of direct expansion solar assisted heat pump systems. In addition, parameter analysis of four evaporator unit types has been conducted, and the recommendation values of each parameter have also been presented. The simulation results show that the roll-bond evaporator (fluid channel width: 10 mm) with hexagon and rectangle patterns have better temperature distribution uniformity than grid and linear types, and their temperature differences are both 0.038 °C while their dimensionless pressure losses are 0.109 and 0.230, respectively. To specifically design different kinds of PVT collector/evaporator or direct expansion evaporators, a novel design method for roll-bond evaporator is proposed, and a combination of hexagon and grid types is recommended for PVT module. Moreover, the recommendation fluid channel width of the roll-bond panel is 8 mm to 13 mm while the scaling ratio is 0.8 to 1.2. The modified efficiency factors are 0.521, 0.564, 0.549, and 0.342 of hexagon, grid, rectangle, and linear types when the fluid channel width is 10 mm, respectively.

Absorption-resorption heat pumps (ARHPs) can efficiently utilize low-temperature solar heat for winter space heating, but are restricted by the relatively weak low ambient temperature adaptability. By combining the different strengthens of vapor compression heat pump (VCHP) and absorption-resorption heat pump (ARHP), a novel solar-assisted resorption-subcooled compression hybrid heat pump system with higher heating capacity under cold climate condition for space heating is proposed. Thermodynamic models for the hybrid system involving two subsystems are developed for performance evaluation under different operation conditions. Feasible high pressure/low pressure (PH/PL) and evaporation temperature/condensation temperature (Te/Ta) ranges for the hybrid system are revealed for component design. Based on that, performance evaluation indices like total coefficient of performance (COPtot), primary energy ratio (PER), primary energy saving ratio (PESR), coefficient from solar irradiation to heating capacity (SCOP) are investigated in terms of different PH/PL and Te/Ta values. The results showed that for the base-case, the above indices are 2.41, 1.66, 0.35 and 1.21, respectively. In addition, heat source temperature demand, heating capacity and ambient air temperature need of the hybrid system are compared with those of the conventional absorption heat pump (AHP), single ARHP and single VCHP under the same operation conditions. The results show that the hybrid system can extend the operation heat source temperature to above 72 °C, highlighting the possibility of integrating with common non-tracking solar collectors, and can extend the feasible ambient air temperature to above −20 °C. Moreover, by recovering the sub-cooling heat of VCHP subsystem for ARHP subsystem operation, the hybrid system can lift the heating capacity by over 50% based on the equivalent VCHP system.

This research involves a GAX-based ammonia-water absorption heat pump, which utilizes solar energy and natural gas as heat source. The experiments of parabolic tough collector and GAX absorption heat pump were carried out separately. GAX absorption heat pump is operated when the ambient temperature is 4.31–11.07 °C, COP approaches 1.44–1.66. Thermal efficiency of the PTC varies from 0.50 to 0.60. A mathematical model of the coupled solar absorption heat pump is built. The effect of each heat exchanger size on the GAX cycle performance is investigated, results show that the heat exchanger size of solution cooled absorber has the greatest impact on the cycle. Both Solar driven mode and Solar-NG driven mode were studied. Solar driven mode is strict with solar energy, if the direct normal irradiance is below 560 W/m2 the system cannot work. Solar-NG driven mode could work under any solar radiation condition. In this mode, generation temperature could be controlled by changing the flow rate of natural gas. The optimal generation temperature is found to be around 180 °C when Tamb = 7 °C, DNI = 800 W/m2, Twout = 45 °C. Besides, system analysis reveals that the heat pump could perform competitive in low ambient temperature if the solar radiation is abundant, which makes Lhasa a perfect site for the system. Economic analysis in Lhasa show that the addition of solar collector could reduce the operating cost by more than 25%.

PV/T (photovoltaic/thermal) technology is a combination of PV module (photovoltaic utilization) and collector (photothermal utilization), which can improve the comprehensive utilization efficiency of solar energy and has a broad application prospect. In this paper, PV/T module is coupled with heat pump evaporator to form a direct-expansion solar PV/T heat pump which is suitable for heat application in high latitude area. To achieve stable residential heating, a solar PV/T heat pump system coupled with build-in PCM (phase change material) heat storage is therefore proposed and simulated. Meanwhile, the mathematical model of solar PV/T heat pump coupled with build-in PCM heat storage system is established and verified. The simulation results show that the temperature of underfloor heating which using build-in PCM heat storage can reach 22–31 °C after 39 h when the circulating water is 40 °C. Moreover, the heating COP (Coefficient of Performance) increases with the increase of solar radiation, ambient temperature and area of PV/T collector, and decrease of wind speed, respectively. A 20 m2 PV/T panel module can output 21.4% of the electricity to power grid when the solar radiation intensity is 600 W/m2 and meet the heat demand of a 100 m2 room while maintain the operation of the system. Meanwhile, the heating COP can reach 5.79 which is 70% higher than the conventional air conditioning system and the electrical, thermal, overall efficiencies are 17.77%, 55.76% and 75.49%, respectively.

In this paper, the refrigerant flow and the thermal performance of a working fluid pump are performed in the perspective of an ejector refrigeration system. The influence of impeller?s geometric parameters on the internal pressure, flow rate and cavitation of the pump is studied experimentally and numerically. A vertical multi-stage centrifugal pump is selected as an experimental prototype for numerical verification, and a working fluid pump, which is optimized by the orthogonal analysis, is numerically studied, the results show that the optimized one has better thermal performance than the prototype.