Search

Carbon fiber (CF) is a potential microwave absorption (MA) material due to the strong dielectric loss. Nevertheless, owing to the high conductivity, poor impedance matching of carbon-based  materials results in limited MA performance. How to solve this problem and achieve excellent MA performance remains a principal challenge. Herein, taking full advantage of CF and excellent impedance matching of bimetallic metal-organic frameworks (MOF) derivatives layer, an excellent microwave absorber based on micron-scale 1D CF and NiCoMOF (CF@NiCoMOF-800) is developed. After adjusting the oxygen vacancies of the bimetallic MOF, the resultant microwave absorber presented excellent MA properties including the minimum reflection loss (RL min ) of -80.63 dB and wide effective absorption bandwidth (EAB) of 8.01 GHz when its mass percent is only 5 wt.% and the thickness is 2.59 mm. Simultaneously, the mechanical properties of the epoxy resin (EP)-based coating with this microwave absorber are effectively improved. The hardness (H), elastic modulus (E), bending strength, and compressive strength of CF@NiCoMOF-800/EP coating are 334 MPa, 5.56 GPa, 82.2 MPa, and 135.8 MPa, which is 38%, 15%, 106% and 53% higher than EP coating. This work provides a promising solution for carbon materials achieving excellent MA properties and mechanical properties., (© 2024 Wiley‐VCH GmbH.)

Multivalent glycosidase inhibitors based on 1-deoxynojirimycin derivatives against α-glucosidases have been rapidly developed. Nonetheless, the mechanism based on self-assembled multivalent glucosidase inhibitors in living systems needs to be further studied. It remains to be determined whether the self-assembly possesses sufficient stability to endure transit through the small intestine and subsequently bind to the glycosidases located therein. In this paper, two amphiphilic compounds, 1-deoxynojirimycin and α-peptoid conjugates ( LP-4DNJ-3C and LP-4DNJ-6C ), were designed. Their self-assembling behaviors, multivalent α-glucosidase inhibition effect, and fluorescence imaging on living organs were studied. LP-4DNJ-6C exhibited better multivalent α-glucosidase inhibition activities in vitro . Moreover, the self-assembly of LP-4DNJ-6C could effectively form a complex with Nile red. The complex showed fluorescence quenching effect upon binding with α-glucosidases and exhibited potent fluorescence imaging in the small intestine. This result suggests that a multivalent hypoglycemic effect achieved through self-assembly in the intestine is a viable approach, enabling the rational design of multivalent hypoglycemic drugs.

The peelable microwave absorption (MA) coating with reversible adhesion for stable presence on substrates and easy release without any residuals is highly desired in temporary electromagnetic protection, which can quickly enter and disengage the electromagnetic protection state according to the real-time changeable harsh surroundings. On the contrary, with the incorporation of abundant absorbent to achieve excellent MA ability, the tunable adhesion and sufficient cohesion are extremely challenging to fulfill the above requirement. The reported peelable coatings still have problems in controlling adhesion/cohesion strength and coating release, facing substantial residuals after peeling even using complex chemical modification or abundant additives. Herein, a peelable MA coating based on the block characteristics of polar and nonpolar segments of poly(styrene-(ethylene- co -butylene)-styrene) (SEBS) is successfully developed. The polyaniline-decorated carbon nanotube as a microwave absorber plays a positive influence on the adhesion/cohesion of the coating due to bonding interaction. The competitive effective absorption bandwidth (EAB) of 8.8 GHz and controllable yet reversible adhesion release on various substrates and complex surfaces have been achieved. The reusability endows peelable MA coating with 93% retention of EAB even after ten coating-peeling cycles. The coating with excellent chemical and adhesion stability can effectively protect substrates from salt/acid/alkali corrosion, showing over 98% retention of EAB even after 8 h of accelerated corrosion. Our peelable MA coating via a general yet reliable approach provides a prospect for temporary electromagnetic protection.

Nucleolus was an important cellular organelle. The abnormal morphology and number of the nucleolus have been considered as diagnostic biomarkers for some human diseases. However, the imaging agent based on nucleolus was limited. In this manuscript, a series of nucleolar fluorescent probes based on naphthalimide derivatives (NI-1 ∼ NI-5) had been designed and synthesized. NI-1 ∼ NI-5 could penetrate cell membranes and nuclear membranes, achieve clear nucleolar staining in living cells. These results suggested that the presence of amino groups on the side chains of naphthalimide backbone could enhance the targeting to the cell nucleolus. In addition, the molecular docking results showed that NI-1 ∼ NI-5 formed hydrogen bonds and hydrophobic interactions with RNA, and exhibited enhanced fluorescence upon binding with RNA. These results will provide favorable support for the diagnosis and treatment of nucleolus-related diseases in the future., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier Inc. All rights reserved.)

The impedance matching performance of carbon nanotubes (CNTs) can be effectively enhanced by developing a uniform magnetic impedance matching layer, which can take on critical significance in achieving the desirable microwave absorption (MA) performance. To obtain a uniform coating of Nickel (Ni) nanoparticles on CNTs, several methods have been developed (e.g., the γ-irradiation technique, electroless deposition, as well as microwave welding method). However, the intricate and complicated conditions of the above-mentioned methods limit their wide application. Therefore, controlling the distribution of Ni nanoparticles with the aid of a concise and effective method remains a great challenge. Herein, in view of the uniform dispersion effect of polyvinylpyrrolidone (PVP) on CNTs and its complexation with Ni ions, uniform coating of Ni nanoparticles on CNTs is well developed after it is introduced in the hydrothermal process. The prepared Ni/CNTs composites exhibited excellent MA performance in comparison with those of reported Ni/CNTs composites for the ideal impedance matching performance and microwave attenuation ability. When the filler content was only 15 wt%, the minimum reflection loss (RL min ) reached -39.5 dB, and the effective bandwidth (EB) with RL < -10 dB reached 5.2 GHz at the thickness of 1.15 mm. A scalable strategy of regulating the distribution of Ni nanoparticles and preparing a lightweight microwave absorber based on CNTs was developed in this study, which can serve as a vital guideline for preparing novel MA composite materials., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier Inc. All rights reserved.)

Given the rapid developments in modern devices, there is an urgent need for shape-memory polymer composites (SMPCs) in soft robots and other fields. However, it remains a challenge to endow SMPCs with both a reconfigurable permanent shape and a locally reversible shape transformation. Herein, a dynamic cross-linked network was facilely constructed in carbon nanotube/ethylene vinyl acetate copolymer (CNT/EVA) composites by designing the molecular structure of EVA. The CNT/EVA composite with 0.05 wt % CNT realized a steady-state temperature of ∼75 °C under 0.11 W/cm 2 light intensity, which gave rise to remote actuation behavior. The dynamic cross-linked network along with a wide melting temperature offered opportunities for chemical and physical programming, thus realizing the achievement of the programmable three-dimensional (3D) structure and locally reversible actuation. Specifically, the CNT/EVA composite exhibited a superior permanent shape reconfiguration by activating the dynamic cross-linked network at 140 °C. The composite also showed a high reversible deformation rate of 11.1%. These features endowed the composites with the capability of transformation to 3D structure as well as locally reversible actuation performance. This work provides an attractive guideline for the future design of SMPCs with sophisticated structures and actuation capability.

Polyimide (PI) foam with excellent microwave absorption (MA) performance and desirable compressive strength is highly critical and in demand in the structural MA components. Although the satisfactory MA performance of the present PI-based MA foams has been achieved by employing diverse methods, the relatively low compressive strength (∼KPa) restricted them from use as structural MA foams in practical application. Herein, isocyanate acid was introduced to the backbone of PI resin, which not only increased the PI backbone polarity and strength as rigid chain segment, but also served as a self-foaming component. The porous structure of PI foams was readily regulated by adjusting the water and carbon nanotube (CNT) filler contents of precursor dispersion. As a result of the improved polarity of the PI backbone resulted from the isocyanate group and high dielectric loss of CNT, the high compressive strength of 7.04 MPa and impressive MA property of the resultant PI foam with a low CNT loading ratio of 1.5 wt % were achieved, which were much higher than those reported previously. Especially, the effective absorption bandwidth (EAB) (RL < -10 dB) was up to 10.7 GHz (at the thickness of 3 mm), covering the C, X, and Ku bands simultaneously. Meanwhile, the EAB of the as-prepared PI foam retained 9.3 and 9.7 GHz even after being subjected to liquid nitrogen (-196 °C) and high temperature (300 °C) treatments due to the desirable stability of PI. In addition, the excellent thermal insulation resulted from the pores structure and low filler content was achieved, where the top surface only presented 60 °C after placing on 300 °C platform for 30 min. The high compressive strength, impressive MA property, and thermal insulation endowed the resultant CNT/PI foam with great potential application as structural MA foam in a harsh service environment.

Although terahertz (THz) spectroscopy demonstrates great application prospects in the fields of fingerprint sensing and detection, traditional sensing schemes face unavoidable limitations in the analysis of trace-amount samples. In this Letter, a novel, to the best of our knowledge, absorption spectroscopy enhancement strategy based on a defect one-dimensional photonic crystal (1D-PC) structure is proposed to achieve strong wideband terahertz wave-matter interactions for trace-amount samples. Based on the Fabry-Pérot resonance effect, the local electric field in a thin-film sample can be boosted by changing the length of the photonic crystal defect cavity, so that the wideband signal of the sample fingerprint can be greatly enhanced. This method exhibits a great absorption enhancement factor, of about 55 times, in a wide terahertz frequency range, facilitating the identification of different samples, such as thin α-lactose films. The investigation reported in this Letter provides a new research idea for enhancing the wide terahertz absorption spectroscopy of trace samples.

Synthetic glycoconjugates as chemical probes have been widely developed for the detection of glycosidase enzymes. However, the binding interactions between iminosugar derivatives and glycosidases were limited, especially for the binding interactions between multivalent glycosidase inhibitors and α-glycosidases. In this paper, three naphthalimide-DNJ conjugates were synthesized. Furthermore, the binding interactions and glycosidase inhibition effects of them were investigated. It was found that the strong binding interactions of multivalent glycosidase inhibitors with enzymes were related to the efficient inhibitory activity against glycosidase. Moreover, the lengths of the chain between DNJ moieties and the triazole ring for the naphthalimide-DNJ conjugates influenced the self-assembly properties, binding interactions and glycosidase inhibition activities with multisource glycosidases. Compound 13 with six carbons between the DNJ moiety and triazole ring showed the stronger binding interactions and better glycosidase inhibition activities against α-mannosidase (jack bean) and α-glucosidase (aspergillus niger). In addition, compound 13 showed an effective PBG inhibition effect in mice with 51.18 % decrease in blood glucose at 30 min. This result opens a way for detection of multivalent glycosidase inhibition effect by a fluorescent sensing method., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier Inc. All rights reserved.)

In this paper, a novel, to the best of our knowledge, polymer-based negative curvature ring-core fiber (NC-RCF) is proposed and investigated. The hollow-core NC-RCF is composed of TOPAS as background material. The inner and outer negative curvature structure layers are connected to the annular area, and the orbital angular momentum (OAM) modes can propagate in the annular core. In the frequency region of 1.0-1.5 THz, the designed NC-RCF can stably transmit 82 OAM modes. Investigation results indicate that the effective refractive index differences between the corresponding HE and EH modes are above 10 -4 . The confinement losses of EH or HE modes are smaller than 10 -8 d B / m , and the dispersion variations are lower than 0.31 ps/THz/cm. Effective mode areas are larger than 5.14 m m 2 . Additionally, the highest mode purity of all vector modes is 99.78%. In addition, modal birefringence, also known as the walk-off length, has also been discussed. All these operation performances indicate that the designed NC-RCF make contributions to the optical communication systems.

Due to the large scale of mining and smelting activities, considerable amounts of heavy metals are discharged into the environment and accumulate in the sediment of rivers and lakes. The combined pollution of heavy metals and the intrinsic phosphorus in sediment calls for novel remediation technologies. In this study, lanthanum-modified zeolite (LMZ) was employed as an inactivation agent for the immobilization of phosphorus, zinc, and lead in sediments. The adsorption capacities as well as the inactivation performance of LMZ for P, Zn, and Pb were investigated, and the adsorption mechanisms were explored via desorption experiments, X-ray photoelectron spectroscopy (XPS), and X-ray diffraction (XRD). The results indicated that the adsorption maximums of LMZ for P, Zn, and Pb were 53.76, 27.70, and 123.45 mg·g -1 , respectively. Pre-adsorption of Zn and Pb had a negligible effect on the P adsorption by LMZ, whereas the adsorption of Zn and Pb were inhibited significantly by the pre-adsorption. P, Zn, and Pb in the sediment were transformed to more stable or less bioavailable forms by dosing 0.83% and 1.66% weight percentages of LMZ. It was found that P, Zn, and Pb were adsorbed through the formation of inner-sphere complexes. Further, desorption experiments and XRD patterns suggested that electrostatic attraction and surface precipitation also contributed to the adsorption of Zn and Pb, respectively.

A multifunctional design based on vanadium dioxide (VO 2 ) metamaterial structure is proposed. Broadband absorption, linear-to-linear (LTL) polarization conversion, linear-to-circular (LTC) polarization conversion, and total reflection can be achieved based on the insulator-to-metal transition (IMT) of VO 2 . When the VO 2 is in the metallic state, the multifunctional structure can be used as a broadband absorber. The results show that the absorption rate exceeds 90% in the frequency band of 2.17 - 4.94 THz, and the bandwidth ratio is 77.8%. When VO 2 is in the insulator state, for the incident terahertz waves with a polarization angle of 45°, the structure works as a polarization converter. In this case, LTC polarization conversion can be obtained in the frequency band of 0.1 - 3.5 THz, and LTL polarization conversion also can be obtained in the frequency band of 3.5 - 6 THz, especially in the 3.755 - 4.856 THz band that the polarization conversion rate is over 90%. For the incident terahertz waves with a polarization angle of 0°, the metamaterial structure can be used as a total reflector. Additionally, impacts of geometrical parameters, incidence angle and polarization angle on the operating characteristics have also been investigated. The designed switchable multifunctional metasurfaces are promising for a wide range of applications in advanced terahertz research and smart applications.

In this paper, a hybrid vanadium dioxide ( V O 2 )-graphene-based bifunctional metamaterial is proposed. The realization of the different functions of perfect transmission and high absorption is based on the insulator-metal phase transition of V O 2 material. The Fermi energy level of graphene can be treated to dynamically tune the absorption and transmission rates of the metamaterial structure. As a result, when V O 2 is in the insulating state, the designed metamaterial can be used as a filter providing three adjustable passbands with center frequencies of 1.892 THz, 1.124 THz, and 0.94 THz, and the corresponding transmittances reach 93.11%, 98.62%, and 90.01%, respectively. The filter also shows good stopband characteristics and exhibits good sensing performance at the resonant frequencies of 1.992 THz and 2.276 THz. When V O 2 is in metal state, the metamaterial structure acts as a double-band absorber, with three absorption peaks (>90 % ) in the range of 0.684 THz to 0.924 THz, 2.86 THz to 3.04 THz, and 3.28 THz to 3.372 THz, respectively. The designed structure is insensitive to the polarization of vertically incident terahertz waves and still maintains good absorption performances over a large range of incidence angles. Finally, the effects of geometric parameters on the absorption and transmission properties of the hybrid bifunctional metamaterials have also been discussed. The switchable metamaterial structures proposed in this paper provide great potential in terahertz application fields, such as filtering, smart sensing, switching, tunable absorbers, and so on.

Terahertz (THz) absorption spectroscopy is a powerful tool for molecular label-free fingerprinting, but it faces a formidable hurdle in enhancing the broadband spectral signals in trace-amount analysis. In this paper, we propose a sensing method based on the geometry scanning of metal metasurfaces with spoof surface polarization sharp resonances by numerical simulation. This scheme shows a significant absorption enhancement factor of about 200 times in an ultra-wide terahertz band to enable the explicit identification of various analytes, such as a trace-amount thin lactose film samples. The proposed method provides a new, to the best of our knowledge, choice for the enhancement of wide terahertz absorption spectra, and paves the way for the detection of trace-amount chemical, organic, or biomedical materials in the terahertz regime.

Composites based on a shape-memory polymer doped with conductive particles are considered as soft actuators for artificial muscles and robots. Low-voltage actuating is expected to reduce equipment requirement and safety hazards, which requires a highly conductive particle content but weakens the reversible deformation. The spatial distribution of the conductive particle is key to decreasing the actuating voltage and maintaining the reversible deformation. Herein, an approach of fabricating a low-voltage actuator that can perform various biomimetic locomotions by spraying and hot pressing is reported. Carbon nanotubes (CNTs) are enriched inside the surface layer of poly(ethylene- co -vinyl acetate) (EVA) to form a high-density conductive network without degradation of the reversible deformation. The bilayer CNT/EVA actuator exhibits a reversible transformation of more than 10% even with 100 cycles, which requires an applied voltage of just 15 V. Taking advantage of the reprogrammability of the CNT/EVA actuator and reversible shift between the different shapes, different biomimetic locomotions (sample actuator, gripper, and walking robot) are demonstrated without any additional mechanical components. A scheme combining the electrical properties and the shape-memory effect provides a versatile strategy to fabricate low-voltage-actuated polymeric actuators, providing inspiration in the development of electrical soft actuators and biomimetic devices.

Highlights: The cationic waterborne polyurethanes microspheres with Diels-Alder bonds were synthesized for the first time. The electrostatic attraction not only endows the composite with segregated structure to gain high electromagnetic-interference shielding effectiveness, but also greatly enhances mechanical properties. Efficient healing property was realized under heating environment. It is still challenging for conductive polymer composite-based electromagnetic interference (EMI) shielding materials to achieve long-term stability while maintaining high EMI shielding effectiveness (EMI SE), especially undergoing external mechanical stimuli, such as scratches or large deformations. Herein, an electrostatic assembly strategy is adopted to design a healable and segregated carbon nanotube (CNT)/graphene oxide (GO)/polyurethane (PU) composite with excellent and reliable EMI SE, even bearing complex mechanical condition. The negatively charged CNT/GO hybrid is facilely adsorbed on the surface of positively charged PU microsphere to motivate formation of segregated conductive networks in CNT/GO/PU composite, establishing a high EMI SE of 52.7 dB at only 10 wt% CNT/GO loading. The Diels-Alder bonds in PU microsphere endow the CNT/GO/PU composite suffering three cutting/healing cycles with EMI SE retention up to 90%. Additionally, the electrostatic attraction between CNT/GO hybrid and PU microsphere helps to strong interfacial bonding in the composite, resulting in high tensile strength of 43.1 MPa and elongation at break of 626%. The healing efficiency of elongation at break achieves 95% when the composite endured three cutting/healing cycles. This work demonstrates a novel strategy for developing segregated EMI shielding composite with healable features and excellent mechanical performance and shows great potential in the durable and high precision electrical instruments., (© 2021. The Author(s).)

Background: As an H3K27me3 demethylase and counteracts polycomb-mediated transcription repression, KDM6B has been implicated in the development and malignant progression in various types of cancers. However, its potential roles in esophageal squamous cell carcinoma (ESCC) have not been explored., Methods: The expression of KDM6B in human ESCC tissues and cell lines was examined using RT-qPCR, immunohistochemical staining and immunoblotting. The effects of KDM6B on the proliferation and metastasis of ESCC were examined using in vitro and in vivo functional tests. RNA-seq and ChIP-seq assay were used to demonstrate the molecular biological mechanism of KDM6B in ESCC., Results: We show that the expression level of KDM6B increased significantly in patients with lymph node metastasis. Furthermore, we confirmed that KDM6B knockdown reduces proliferation and metastasis of ESCC cells, while KDM6B overexpression has the opposite effects. Mechanistically, KDM6B regulates TNFA&#95;SIGNALING&#95;VIA&#95;NFκB signalling pathways, and H3K27me3 binds to the promoter region of C/EBPβ, leading to the promotion of C/EBPβ transcription. Besides, we show that GSK-J4, a chemical inhibitor of KDM6B, markedly inhibits proliferation and metastasis of ESCC cells., Conclusions: The present study demonstrated that KDM6B promotes ESCC progression by increasing the transcriptional activity of C/EBPβ depending on its H3K27 demethylase activity.

This publisher's note contains corrections to Opt. Lett.46, 290 (2021)OPLEDP0146-959210.1364/OL.412229.

At present, most of the gradient metasurfaces used to construct surface plasmon polaritons (SPPs)/spoof SPPs (SSPs) couplers are usually compact metal antennas working under reflection and transmission. In reflection mode, meta-couplers link propagating waves and surface waves (SWs), and SWs will undergo significant scattering before coupling to an Eigen SPP in the target system. In transmission mode, metal meta-couplers will encounter complex multilayer designing at the microwave/terahertz region and metal absorption loss at optical frequencies. In this Letter, to the best of our knowledge, a novel design using dielectric gradient metasurfaces instead of metal metasurface couplers is proposed to excite broadband SSPs on the metal groove array. We demonstrate that the well-designed phase dielectric gradient metasurface converts the normal incident terahertz wave to the predetermined angle in the dielectric substrate and then excites the broadband SSPs with the transmission coupling between the dielectric meta-coupler and SSPs surface. This research may open up new avenues in simple and broadband plane dielectric meta-couplers for SSPs in ultra-thin and compact functional devices for versatile applications.

Conductive textiles (CTs) are promising electromagnetic interference (EMI) shielding materials. Nevertheless, limited stretchability and poor reliability restrict their potential applications in stretchable electronic devices because of the rigid conductive networks. Herein, a highly stretchable and reliable CT is developed for effective EMI shielding by designing a deformable liquid-metal (LM) coating and polydimethylsiloxane (PDMS) protective layer. The resultant PDMS-LM/Textile exhibits an outstanding EMI shielding efficiency (EMI SE) of 72.6 dB at a thickness of only 0.35 mm while maintaining EMI SEs of 66.0 and 52.4 dB under strains of 30 and 50%, respectively. The corresponding EMI SEs hold 91.7 and 80.3% retention after 5000 stretching-releasing cycles, respectively. The superior and durable EMI SE should be ascribed to the perfect connectivity and good deformability of conductive LM networks. Moreover, the LM coating has a robust fastness to the textile substrate, without any obvious decrease in EMI SE after 10 min of ultrasonic treatment and 100 peeling cycles because of the protective effect of the PDMS layer. This work provides a novel route to developing highly stretchable CTs for advanced EMI shielding applications, especially in the field of highly stretchable electronic devices.

In this paper, with the assumption that infectious individuals, once recovered for a period of fixed length, will relapse back to the infectious class, we derive an epidemic model for a population living in a two-patch environment (cities, towns, or countries, etc.). The model is given by a system of delay differential equations with a fixed delay accounting for the fixed constant relapse time and a non-local term caused by the mobility of the individuals during the recovered period. We explore the dynamics of the model under two scenarios: (i) assuming irreducibility for three travel rate matrices; (ii) allowing reducibility in some of the three matrices. For (i), we establish the global threshold dynamics in terms of the principal eigenvalue of a 2×2 matrix. For (ii), we consider three special cases so that we can obtain some explicit results, which allow us to explicitly explore the impact of the travel rates. We find that the role that the travel rate of recovered and infectious individuals differs from that of susceptible individuals. There is also an important difference between case (i) and (ii): under (ii), a boundary equilibrium is possible while under (i) it is impossible.

The pressure sensor with high sensitivity and a broad pressure sensing range is highly desired for flexible electronics. Here, a high-performance pressure sensor based on a hybrid structure was facilely fabricated using the glass template method, which consists of polyurethane (PU) mesodomes embedded with gradient-distributed silver nanowire (AgNW). Such a novel hybrid architecture enables the as-prepared PU/AgNW pressure sensor to have high sensitivity as well as a wide detection range. Moreover, the obtained PU/AgNW pressure sensors have a fast response time (20 ms), good cycling stability, and excellent flexibility. The pressure sensor, benefiting from its outstanding comprehensive sensing performance, can be used for expression recognition and human activity monitoring, showing tremendous application potential in wearable devices. The proposed architecture and developed methodology in this work is promising for future flexible electronic applications.

Developing high-performance electromagnetic interference (EMI) shielding materials with high absorption coefficient is highly desired for eliminating the secondary pollution of reflected electromagnetic wave (EMW). Nevertheless, it has long been a daunting challenge to achieve high shielding effectiveness (SE) and ultralow or no reflection SE simultaneously. Herein, highly porous and conductive carbon nanotube (CNT)-based carbon aerogel with a meticulously designed hierarchically porous structure from micro and sub-micro to nano levels is developed by specific two-stage pyrolysis and potassium hydroxide activation processes. The resultant activated cellulose-derived carbon aerogels (a-CCAs) exhibit an ultrahigh EMI SE of 96.4 dB in the frequency range of 8.2-12.4 GHz in conjunction with an exceptionally high absorption coefficient of 0.79 at a low density of 30.5 mg cm -3 . The successful construction of hierarchically porous structure is responsible for the excellent "structurally absorbing" ability of a-CCAs, and the introduction of CNT-based heterogeneous conductive network can effectively dissipate the incident EMWs by interfacial polarization and microcurrent losses. Moreover, the as-prepared a-CCAs have a water contact angle of as high as 158.3°and a sliding angle of as low as 5.3°, revealing their superhydrophobic feature. The ingenious structure design proposed here provides a possible pathway to overcome the conflict between high EMI shielding performance and ultralow or no secondary reflection, and the as-prepared a-CCAs are exceedingly promising in the application of telecommunication, microelectronics, and spacecraft.

Excellent electromagnetic interference (EMI) shielding ability, light weight, and good heat resistance are highly required for practical applications of EMI shielding materials, such as in areas of aerospace, aircraft, and automobiles. Herein, a lightweight and robust carbon nanotube (CNT)/polyimide (PI) foam was developed for efficient and heat-resistant EMI shielding. Thanks to poly(vinyl pyrrolidone) (PVP) as a surfactant that not only promotes the uniform dispersion of CNTs to form perfect CNT conductive networks but also can be removed in situ during the polymerization process, the density of resultant CNT/PI foam is only 32.1 mg·cm -3 , and the EMI shielding effectiveness (EMI SE) is up to 41.1 dB, which represents one of the highest EMI SE values compared to previously reported polymer-based foams. The CNT/PI foam also achieves the absorption coefficient ( A ) of up to 82.3%, which is very impressive in CNT/polymer foams at comparable EMI SE levels. The PI matrix endows the foam with excellent heat resistance. The as-prepared CNT/PI foam presents a higher EMI SE than 35 dB even after being subjected to the flame of an alcohol burner. Moreover, the compressive strength and compressive modulus are up to 240.9 and 323.9 kPa. These results indicate its certain application potential in the harsh requirement of aeronautics and aerospace industries as a highly efficient and lightweight EMI shielding material.

Flexible strain sensors based on elastomeric conductive polymer composites (ECPCs) play an important role in wearable sensing electronics. However, the achievement of good conjunction between broad detection range and high sensitivity is still challenging. Herein, a highly stretchable and sensitive strain sensor was developed with the formation of porous segregated conductive network in the carbon nanotube/thermoplastic polyurethane composite via a facile and nontoxic compression-molding plus salt-leaching method. The strain sensor with porous segregated conductive network exhibited perfect combination of ultrawide sensing range (800% strain), large sensitivity (gauge factor of 356.4), short response time (180 ms) and recovery time (180 ms), as well as superior stability and durability. The integrated porous structure intensifies the deformation of segregated conductive network when tension strain is applied, which benefits enhancement of the sensitivity. Our sensor could monitor not only subtle oscillation and physiological signals but also energetic human motions efficiently, revealing promising potential applications in wearable motion monitoring systems. This work provides a unique and effective strategy for realizing ECPCs based strain sensors with excellent comprehensive sensing performances.

An efficient electromagnetic interference (EMI) shielding paper with excellent water repellency and mechanical flexibility has been developed, by assembling silver nanowires (AgNWs) and hydrophobic inorganic ceramic on the cellulose paper, via a facile dip-coating preparation. Scanning electron microscope (SEM) observations confirmed that AgNWs were interconnected and densely coated on both sides of the cellulose fiber, which endows the as-prepared paper with high conductivity (33.69 S/cm in-plane direction) at a low AgNW area density of 0.13 mg/cm 2 . Owing to multiple reflections and scattering between the two outer highly conductive surfaces, the obtained composite presented a high EMI shielding effectiveness (EMI SE) of up to 46 dB against the X band, and ultrahigh specific EMI SE of 271.2 dB mm -1 . Moreover, the prepared hydrophobic AgNW/cellulose (H-AgNW/cellulose) composite paper could also maintain high EMI SE and extraordinary waterproofness (water contact angle > 140°) by suffering dozens of bending tests or one thousand peeling tests. Overall, such a multifunctional paper might have practical applications in packaging conductive components and can be used as EMI shielding elements in advanced application areas, even under harsh conditions.

Terminthia paniculata (Sanyeqi) is widely used for treating inflammation and rheumatic arthritis in the folk areas of Yunnan province, China. Its total extract was first revealed with xanthine oxidase (XO) inhibitory activity in vitro and anti-hyperuricemic effect in vivo. Bioassay-guided separation on Fr. A5 yielded six chalcone-flavonone heterodimers, termipaniculatones A-F. Their structures were elucidated based on extensive spectroscopic analyses involving HRESIMS, 1D and 2D NMR, UV, IR and [α] D , and the absolute configuration of termipaniculatone F was verified by ECD calculation. Termipaniculatones A and E showed obvious XO inhibitory activity with IC 50 values of 55.6 and 89.5 μM, respectively, which took effects via a mix-type mode. A molecular modeling study revealed that termipaniculatone A was well located into the active site of XO by interacting with Glu802, Arg880, Thr1010 and Val1011 residues. Termipaniculatone A showed anti-hyperuricemic effects by decreasing serum uric acid levels and inhibiting XO activity in both serum and liver on potassium oxonate (PO)-induced hyperuricemia mice, and anti-inflammatory activity through alleviating paw swelling on monosodium urate (MSU)-induced mice, at the concentration of 20 mg/kg. This is the first time to reveal the anti-hyperuricemic and anti-acute gouty arthritis potency of T. paniculata and the characteristic biflavonoids as active constituents, which provides valuable information for searching new XO inhibitors from natural sources., (Copyright © 2019 Elsevier Ltd. All rights reserved.)

Flexible strain sensors have attracted a great amount of attention for promising applications in next-generation artificially intelligent devices. However, it is difficult for conventional planar strain sensors to meet the requirements of miniature size and light weight for flexible electronics. Herein, a highly sensitive and stretchable fiber strain sensor with a millimeter diameter was innovatively fabricated by the capillary tube method to integrate silver nanowires (AgNWs) in polyurethane (PU) fibers. Scanning electron microscopy results demonstrate that AgNWs were embedded into the surface layer of PU fibers and formed completely conductive networks. The unique AgNW networks endow the PU/AgNW fibers with superior electrical conductivity of 3.1 S/cm, high elongation at break of 265%, wide response range of 43%, high gauge factor of 87.6 up to 22% strain, fast response time of 49 ms, and excellent reliability and stability. Such satisfactory stretchability and sensitivity is attributed to the combination of the highly stretchable PU matrix and the embedded architecture of the AgNW conductive network. Moreover, PU/AgNW fibers can be employed as wearable devices to detect various human motions and to drive light-emitting diodes at a lower voltage (2.7 V).

In this work, an SIRS model with age structure is proposed for recurrent infectious disease by incorporating temporary immunity and delay. We formulate the model as an abstract non-densely defined Cauchy problem and derive the conditions for the global stability of disease free equilibrium, the local stability of endemic equilibrium, and the existence of Hopf bifurcation. Both non-periodic and periodic behaviors are possible when the disease persists in population, where time delay plays an important role. Numerical examples are provided to illustrate our theoretical results.

Conventional polymers are usually processed at a much higher temperature than room temperature, which inevitably leads to huge energy consumption and degradation of the polymers and thus a low recycling ability. Herein, we synthesized a poly( n-butyl acrylate)@polystyrene (PBA@PS) core-shell polymer to prepare a typical baroplastic (processible at room temperature). However, this type of baroplastics always has a low mechanical property. To solve this problem, in this work, we introduced hydrogen bonds into the matrix and successfully reinforced baroplastics for the first time. The hydrogen-bonded interaction was introduced by complexing PBA@PS with poly(acrylic acid) and poly(ethylene oxide). The results show that the reinforced baroplastics possessed notably enhanced mechanical properties and good processability. Their mechanical strength and modulus reached as high as 5.6 (by 73%) and 10 MPa (by 400%), respectively. Moreover, the baroplastics could be remolded many times at room temperature and, at the same time, still showed a higher tensile strength (10.5 MPa, 3.3 times that of the initial PBA@PS, which was never achieved in previous works), which resulted from the reversible hydrogen bonds and reserved orientation of molecular chains. Our work opened a new path to reinforce baroplastics and could widen their applications. Furthermore, not limited to the hydrogen bonds, more sacrificial bonds, such as ionic bonds, host-guest interactions, and metal-ligand coordination bonds, could be used to fabricate high-performance baroplastics.

Superhydrophobic electromagnetic interference (EMI) shielding textile (EMIST) is of great significance to the safety and long-term service of all-weather outdoor equipment. However, it is still challenging to achieve long-term durability and stability under external mechanical deformations or other harsh service conditions. Herein, by designing and implementing silver nanowire (AgNW) networks and a superhydrophobic coating onto a commercial textile, we demonstrate a highly robust superhydrophobic EMIST. The resultant EMIST shows a synergy of high water contact angle (160.8°), low sliding angle (2.9°), and superior EMI shielding effectiveness (51.5 dB). Remarkably, the EMIST still maintains its superhydrophobic feature and high EMI shielding level (42.6 dB) even after 5000 stretching-releasing cycles. Moreover, the EMIST exhibits strong resistance to ultrasonic treatment up to 60 min, peeling test up to 100 cycles, strong acidic/alkaline solutions, and different organic solvents, indicating its outstanding mechanical robustness and chemical durability. These attractive features of the EMIST are mainly a result of the joint action of AgNWs, carbon nanotubes, polytetrafluoroethylene nanoparticles, and fluoroacrylic polymer. This work offers a promising approach for the design of future durable, superhydrophobic EMISTs, which are capable of remaining fully functional against long-time exposure to extreme conditions, for example, wet and corrosive environments.

Polypropylene random co-polymer (PPR)/styrene-ethylene-butylene-styrene (SBS) block copolymer blends with high toughness and favorable tensile properties were successfully obtained by blending with traces of multi-wall carbon nanotubes (MWCNTs) and β-nucleating agents (β-NAs). β-NAs can effectively induce the ductile β-form crystal in the PPR matrix. Although the addition of MWCNTs was reported to be only benefit for the tensile strength of PPR and relatively disadvantageous for the toughness, the obviously synergistic toughening effect in PPR/SBS blends was found when MWCNTs and β-NAs coexisted. The notched izod impact strength of PPR/30 wt % SBS blend with MWCNTs and β-NAs increased from 11.3 to 58.9 kJ/m²; more than 5-fold increment compared with pure PPR. Meanwhile, the tensile strength retention of this PPR blend is still above 72.2%. The micro-morphology indicated that the MWCNTs can act as bridges between SBS particle and PPR matrix, effectively transferring the stress and absorbing impact energy among SBS particles.

Composite aerogels consisting of graphene oxide (GO) and regenerated cellulose (RCE) were prepared via a solution mixing-regeneration and freeze-drying process. The prepared RCE/GO composites aerogel exhibited 3D network thin-walled pore structure with large specific surface area, also favorable compression recovery capability, outstanding dye elimination efficiency and reusability after the addition of GO. With addition of only 0.5 wt% GO, the methylene blue (MB) elimination efficiency of RCE/GO aerogel reached 99.0% and still remained at 90.5% after five-time reused under oscillation adsorption. In addition, our research indicates that the excellent MB adsorption of RCE/GO composite aerogel was driven by electrostatic interactions and followed a pseudo-second-order adsorption kinetic and monolayer Langmuir adsorption isotherm. This investigation provides the guidance for the development of green environmental adsorbents to remove organic dye from sewage water., (Copyright © 2018 Elsevier Inc. All rights reserved.)

Personal cooling technologies (PCTs) locally control the temperature of an individual instead of a whole building and are thus energy saving. However, most PCTs still consume energy and are heavy in weight, restricting their application among human beings. To achieve personal thermal comfort and no energy consumption on hot summer days, we designed a bilayer structure fabric with high thermal comfort by increasing the dissipation of human thermal radiation and reducing solar energy absorption simultaneously. The fabric consisted of two layers, including a polyethylene film with nanopores (100-1000 nm in pore size) and a film made of nylon 6 nanofibers (ca. 100 nm in diameter) with beads (ca. 230 nm in diameter), which could increase the visible light reflectance but not affect the infrared wave radiation. Therefore, the designed fabric showed a high heat dissipation power, which was 14.13, 17.93, and 17.93 W/m 2 higher than that of the selected traditional textiles of cotton, linen, and odile, respectively, suggesting good cooling capability. Its cooling performance was better than those reported by the previous research works even at a higher ambient temperature. Meanwhile, the moisture penetrability and hygroscopic property results indicated that the wearing comfort of the designed fabric reached the levels of the selected traditional textiles.

Lightweight conductive polymer composites based on biomass could be a promising candidate for electromagnetic interference (EMI) shielding application. Herein, tailoring porous microstructure and regulating the distribution of carbon nanotubes (CNTs) in cellulose composites are attempts to achieve highly efficient EMI shielding properties accompanying desired mechanical property and low density. Specifically, aligned porous structure is fabricated by ice-template freeze-drying method; meanwhile, CNT is regulated to decorate inside the cellulose matrix (CNT-matrix/cellulose porous composites) or to directly bind over the cellulose cell walls (CNT-interface/cellulose porous composites). It is found that, owing to the preferential distribution of CNT on the cell walls, the CNT-interface/cellulose porous composites possess a very high electrical conductivity of 38.9 S m -1 with an extremely low percolation threshold of 0.0083 vol % with regard to CNT-matrix/cellulose porous composites. Therefore, a shielding effectiveness of 40 dB with merely 0.51 vol % CNT under a thickness of 2.5 mm is achieved in CNT-interface/cellulose porous composites, which is attributed to efficient multiple reflections and the accompanying absorption with promoted conductivity and better-defined porous structure. More laudably, the CNT-interface/cellulose porous composites reveal a superior mechanical property with a specific modulus of 279 MPa g -1 cm 3 . The value behind the current work is to pave an effective way to fabricate environmentally benign, high-performance EMI shielding materials to practically boost numerous advanced applications of cellulose.

Lightweight and robust carbon nanotube (CNT)/chitosan (CS) foams were assembled by a facile unidirectional freeze-drying method in this work. The CNT/CS foam exhibited an excellent electromagnetic interference (EMI) shielding effectiveness (SE) of 37.6 dB while the density was only 17.6 mg·cm -3 , and thus the corresponding specific SE was up to 8556 dB·cm 2 ·g -1 . The superior EMI shielding performance was mainly attributed to the perfect conductive networks. Additionally, the absorption coefficient of CNT/CS foam was up to 81.73% under high EMI SE of 37.6 dB, which was remarkable among the reported EMI shielding materials with comparable EMI shielding level. More importantly, the addition of CS significantly increased the compressive strength and modulus of CNT/CS foam to 34.1 KPa and 177.1 KPa, which were 84% and 149% higher than those for the pure CNT foam, respectively. These results indicate that the CNT/CS foam is an ideal high-efficient EMI shielding material, which has high potential applications in the fields of aerospace, automotive, and electronic devices., (Copyright © 2018 Elsevier Inc. All rights reserved.)

We demonstrate a 266 nm ultraviolet (UV) picosecond laser by fourth-harmonic generation of a Nd:YAG laser with a 5.4 mm thick NaSr 3 Be 3 B 3 O 9 F 4 (NSBBF) crystal. A maximum output power exceeding 1 W at 266 nm was obtained (the highest output power being 1.6 W), corresponding to a conversion efficiency of 10.3%. The stability measurements on the NSBBF crystal with a fluctuation of 3.34% at 200 mW within 1 h indicate that it is a promising UV nonlinear optical material for practical applications. In addition, for the first time, to the best of our knowledge, we measured the effective nonlinear coefficient of NSBBF crystal at 266 nm and compared it with that of β-BaB 2 O 4 crystal.

In this work, we propose novel layer-structured polymer composites (PCs) for manipulating the electromagnetic (EM) wave transport, which holds unique electromagnetic interference (EMI) shielding features. The as-prepared PCs with a multilayered structure exhibits significant improvement in overall EMI shielding effectiveness (EMI SE) by adjusting the contents and distribution of electrical and magnetic loss fillers. The layer-structured PCs with low nanofiller content (5 wt % graphene nanosheets (GNSs) and 15 wt % Fe₃O₄) and a thickness of only 2 mm exhibited ultrahigh electrical conductivity and excellent EMI SE, reaching up to 2000 S/m and 45.7 dB in the X-band, respectively. The increased EMI SE of the layer-structured PCs was mainly based on the improved absorption rather than the reflection of electromagnetic waves, which was attributed to the "absorb-reflect-reabsorb" process for the incident electromagnetic waves. This work may provide a simple and effective approach to achieve new EMI shielding materials, especially for absorption-dominated EMI shielding.

Depression is associated with high mortality and morbidity rates worldwide. By our random screening, it was first revealed that 23 magnolol derivatives were synthesized followed by in vitro and in vivo evaluation of their antidepressive potential. Compound 7c was found to be the most promising compound, with EC 50 values of 396.5 and 383.0 μM agitating on MT 1 and MT 2 receptors, respectively. Additionally, we carried out in vivo experiments to confirm the efficacy and safety of compound 7c; the compound was found to be orally bioavailable and highly effective, leading to a significant reduction of immobility time in a mouse model of depression (forced swimming test and tail suspension test); the acting mechanism was explored by determining its effect on the levels of monoamine neurotransmitters and their metabolites in different mice brain regions; the acute toxicity study showed that the 50% lethal dose (LD50) of 7c was higher than 2000 mg/kg, p. o. A total of 25 metabolites of 7c were identified, including 5 metabolites in phase I and 20 metabolites in phase II. Altogether, these results indicate that magnolol derivative 7c is a promising lead compound for the development of a new chemical class of antidepressant drugs., (Copyright © 2018 Elsevier Masson SAS. All rights reserved.)

Ten new (1-10) and ten known (11-20) diterpenoids involving ent-atisane, ent-seco-atisane, ent-kaurane and ent-seco-kaurane types were isolated from Sapium insigne under the guidance of LCMS-IT-TOF analyses. Their structures were characterized by extensive spectroscopic analyses (HRESIMS, UV, IR, 1D and 2D NMR). A putative biosynthetic pathway was proposed for ent-seco-atisane diterpenoids. Their inhibitory activities on α-glucosidase in vitro were tested for the first time. Compound 4 showed moderate inhibitory effect on α-glucosidase with an IC 50 value of 0.34 mM via a noncompetitive inhibition mechanism (K i  = 0.27 mM). The preliminary structure-activity relationships of the ent-atisane diterpenoids inhibiting α-glucosidase were discussed., (Copyright © 2018 Elsevier B.V. All rights reserved.)

Highly efficient electromagnetic shielding materials entailing strong electromagnetic wave absorption and low reflection have become an increasing requirement for next-generation communication technologies and high-power electronic instruments. In this study, a new strategy is employed to provide flexible waterborne polyurethane composite films with an ultra-efficient electromagnetic shielding effectiveness (EMI SE) and low reflection by constructing gradient shielding layers with a magnetic ferro/ferric oxide deposited on reduced graphene oxide (rGO@Fe 3 O 4 ) and silver-coated tetraneedle-like ZnO whisker (T-ZnO/Ag) functional nanoparticles. Because of the differences in density between rGO@Fe 3 O 4 and T-ZnO/Ag, a gradient structure is automatically formed during the film formation process. The gradient distribution of rGO@Fe 3 O 4 over the whole thickness range forms an efficient electromagnetic wave absorption network that endows the film with a strong absorption ability on the top side, while a thin layer of high-density T-ZnO/Ag at the bottom constructs a highly conductive network that provides an excellent electromagnetic reflection ability for the film. This specific structure results in an "absorb-reflect-reabsorb" process when electromagnetic waves penetrate into the composite film, leading to an excellent EMI shielding performance with an extremely low reflection characteristic at a very low nanofiller content (0.8 vol % Fe 3 O 4 @rGO and 5.7 vol % T-ZnO/Ag): the EMI SE reaches 87.2 dB against the X band with a thickness of only 0.5 mm, while the shielding effectiveness of reflection (SE R ) is only 2.4 dB and the power coefficient of reflectivity ( R) is as low as 0.39. This result means that only 39% of the microwaves are reflected in the propagation process when 99.9999998% are attenuated, which is the lowest value among the reported references. This composite film with remarkable performance is suitable for application in portable and wearable smart electronics, and this method offers an effective strategy for absorption-dominated EMI shielding.

Electromagnetic protection in optoelectronic instruments such as optical windows and electronic displays is challenging because of the essential requirements of a high optical transmittance and an electromagnetic interference (EMI) shielding effectiveness (SE). Herein, we demonstrate the creation of an efficient transparent EMI shielding film that is composed of calcium alginate (CA), silver nanowires (AgNWs), and polyurethane (PU), via a facile and low-cost Mayer-rod coating method. The CA/AgNW/PU film with a high optical transmittance of 92% achieves an EMI SE of 20.7 dB, which meets the requirements for commercial shielding applications. A superior EMI SE of 31.3 dB could be achieved, whereas the transparent film still maintains a transmittance of 81%. The integrated efficient EMI SE and high transmittance are superior to those of most previously reported transparent EMI shielding materials. Moreover, our transparent films exhibit a highly reliable shielding ability in a complex service environment, with 98 and 96% EMI SE retentions even after 30 min of ultrasound treatment and 5000 bending cycles (1.5 mm radius), respectively. The comprehensive performance that is associated with the facile fabrication strategy imparts the CA/AgNW/PU film with great potential as an optimized EMI shielding material in emerging optoelectronic devices, such as flexible solar cells, displays, and touch panels.

Carbon nanotube/high density polyethylene (CNT/HDPE) foam composites with high electrical conductivity and electromagnetic interference (EMI) shielding performance were developed by means of compression molding plus salt-leaching. The uniform porous structure and interconnected CNT networks throughout the cell backbones endowed the as-prepared foam composites with a significantly lower electrical percolation threshold (0.22 vol%) than that of the solid composites (0.84 vol%). Owing to the multiple reflections and scattering between the cell-matrix interfaces, the foam composites presented a superior specific EMI shielding effectiveness (EMI SE) of 104.3 dB cm 3 g -1 , 2.2 times higher than that of their solid counterpart. Besides this, the pore sizes of the CNT/HDPE foam composites could be easily tuned by controlling the particle size of the porogen. Also, the electrical conductivity and specific EMI SE increased with an increase in the cell diameter, which was attributed to the formation of a more perfect conductive network in the cell backbones. Our approach provides a novel idea for fabricating new lightweight EMI shielding materials, especially for aircraft and spacecraft applications., Competing Interests: There are no conflicts to declare., (This journal is © The Royal Society of Chemistry.)

Magnetic bentonite is modified by an amphoteric surfactant (dodecyl dimethyl betaine, BS-12), then modified by a cationic surfactant (Cetyl Trimethyl Ammonium Bromide, CTMAB) and anionic surfactant (Sodium lauryl sulfonate, SDS). Amphoteric-cationic modified magnetic bentonite (BS-CT-MBT) and amphoteric-anionic modified magnetic bentonite (BS-SDS-MBT) are obtained. Structural identification of the samples were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), thermogravimetric analyses (TG), Fourier transform infrared spectra (FTIR), and vibrating sample magnetometer (VSM). The carbon-nitrogen content, specific surface area, and pore volume were also evaluated. Batch isotherm studies were conducted to evaluate the sorption of phenol. The results show that BS-CT-MBT and BS-SDS-MBT can be separated by magnetic separation. The carbon content-nitrogen content and content of surfactants of the BS-CT-MBT increase, while surface area and pore volume decrease compared to those of BS-MBT. Compared with BS-MBT, the carbon-nitrogen content, content of surfactants, and pore volume of BS-SDS-MBT are decreasing and surface area is increasing. The desorption rate of the surfactants is less than 9% at pH 6.0 and in 0.1 mol·L -1 NaCl solution. The Henry equation is the optimal description for the phenol sorption isotherms, implying a partitioning sorption process. The amount of phenol sorption follows the order:BS-CT-MBT > BS-MBT > BS-SDS-MBT > BT > MBT, which significantly correlates with the variation of the content of surfactant. Amphoteric magnetic bentonites modified by CTMAB have better absorption performance for phenol than those modified by SDS.

Objective: Myocardial cell apoptosis represents important pathologic basis of ischemia-reperfusion injury (I/R). MiR-23a is related to myocardial hypertrophy and cardiac remodeling by regulating myocardial cell growth and apoptosis. This study intended to observe the regulating effect of miR-23a in myocardial cell and related target, and investigate its clinical significance to I/R injury., Materials and Methods: The rats were divided into sham group and myocardial I/R group. Myocardial cell cycle and miR-23a expression were tested. H2O2 was applied to treat H9c2 rat myocardial cell to simulate oxidative stress during I/R. The cells were divided into blank group, NC group, miR-23a mimic group, H2O2 group, and miR-23a + H2O2 group. ROS content and cell apoptosis were detected by flow cytometry. MiR-23a, FoxO3a, and BIM gene expression were determined by qRT-PCR. FoxO3a and BIM protein levels were measured by Western blot., Results: Compared with sham group, myocardial apoptosis increased, while miR-23a expression was significantly downregulated in I/R group. H2O2 treatment markedly increased ROS levels in H9c2 cells and elevated apoptosis. The overexpression of mMiR-23a effectively reduced cell apoptosis induced by H2O2 treatment. H2O2 treatment significantly decreased miR-23a expression, while markedly elevated the levels of FoxO3a and BIM. The overexpression of miR-23a apparently impeded the induction of FoxO3a and BIM by H2O2., Conclusions: The downregulation of miR-23a plays a negative role in oxidative stress and cell apoptosis induced by I/R. The overexpression of miR-23a is of significance to alleviate cell apoptosis through inhibiting FoxO3a and downstream target BIM expression.

This study was designed to assess the efficacy of vacuum sealing drainage (VSD) on skull exposure wounds in rabbits and to investigate the underlying mechanism of the process. Full-thickness excisional circular wounds 2×2 cm with or without periosteum involvement were created in 88 New Zealand white rabbits (mean body weight: 3.0±0.65 kg). Animals were randomly divided into 4 groups: periosteum-intact wounds treated with traditional dressing (p+control), periosteum-intact wounds treated with VSD (p+VSD), periosteum-lacking wounds treated with traditional dressing (p-control) and periosteum-lacking wounds treated with VSD (p-VSD). The wounds treated with traditional dressing were covered with Vaseline gauze, while VSD treatment was accompanied with continuous -120 mmHg pressure. Finally, wound tissues were harvested for analysis of hydroxyproline content and histologic detection. VSD hastened the wound healing process significantly (P<0.05) compared to the corresponding control groups. VSD alleviated the inflammation reaction, accelerated re-epithelialization and facilitated the organization of collagen fibers into neat rows. During the wound healing process, the hydroxyproline content increased overtime [i.e., postoperative days (POD) 7, POD 10 and POD 15] in all four groups, and it peaked in the p+VSD group. VSD also promoted angiogenesis via increasing number and quality of collagen. We concluded that VSD can promote healing in bone-exposed wounds via increasing hydroxyproline content and vessel density, reducing inflammatory responses and generating ordered collagen arrangement.

In this paper, the dispersion of carbon nanotube (CNT) in ethylene vinyl acetate (EVA) is demonstrated to be significantly improved by the addition of octadecylamine (ODA)-grafted graphene oxide (GO) (GO⁻ODA). Compared to the CNT/EVA composite, the resultant GO⁻ODA/CNT/EVA (G⁻CNT/EVA) composite shows simultaneous increases in tensile strength, Young's modulus and elongation at break. Notably, the elongation at break of the G⁻CNT/EVA composite still maintains a relatively high value of 1268% at 2.0 wt % CNT content, which is more than 1.6 times higher than that of CNT/EVA composite (783%). This should be attributed to the homogeneous dispersion of CNT as well as the strong interfacial interaction between CNT and EVA originating from the solubilization effect of GO⁻ODA. Additionally, the G⁻CNT/EVA composites exhibit superior electrical conductivity at low CNT contents but inferior value at high CNT contents, compared to that for the CNT/EVA composite, which depends on the balance of CNT dispersion and the preservation of insulating GO⁻ODA. Our strategy provides a new pathway to prepare high performance polymer composites with well-dispersed CNT., Competing Interests: The authors declare no conflict of interest.