Search

Mullite fiber felt is a promising material that may fulfill the demands of advanced flexible external thermal insulation blankets. However, research on the fabrication and performance of mullite fiber felt with high-temperature resistance and thermal stability is still lacking. In this work, mullite fibers were selected as raw materials for the fabrication of mullite fibrous porous materials with a three-dimensional net structure. Said materials' high-temperature resistance and thermal stability were investigated by assessing the effects of various heat treatment temperatures (1100 °C, 1300 °C, and 1500 °C) on the phase composition, microstructure, and performance of their products. When the heat treatment temperature was below 1300 °C, both the phase compositions and microstructures of products exhibited stability. The compressive rebound rate of the product before and after 1100 °C reached 92.9% and 84.5%, respectively. The backside temperature of the as-prepared products was 361.6 °C when tested at 1500 °C for 4000 s. The as-prepared mullite fibrous porous materials demonstrated excellent high-temperature resistance, thermal stability, thermal insulation performance, and compressive rebound capacity, thereby indicating the great potential of the as-prepared mullite fibrous porous materials in the form of mullite fiber felt within advanced flexible external thermal insulation blankets. [ABSTRACT FROM AUTHOR]

To prepare a coating with a high emissivity and low solar absorption ratio on the surface of aluminum silicate fiber cloth, the sol-gel method was used with silica sol as a binder. In this study, the effects of two white fillers, titanium oxide and zirconia, on the substrate and radiation properties of coatings were compared after heat treatment at 800–1200 °C. The ZrO 2 -based coating had good stability after heat treatment at 800–1200 °C, and maintained its white color, exhibiting solar absorption ratio of approximately 0.14 and emissivity of 0.84. ZrO 2 -based coatings prevented harmful cracking, as observed for the TiO 2 -based coatings after heat treatment, because of the ZrO 2 phase transformation. The ZrO 2 -based coating did not have strong bonding with the substrate, and the substrate strength was improved by maintaining a weak bonding interface. Compared with the TiO 2 -based coatings, which exhibit reduced substrate strength above 1000 °C, the ZrO 2 -based coating was more suitable for the surface of flexible fiber cloths as a temperature-resistant coating with good development prospects. [ABSTRACT FROM AUTHOR]

Fibrous porous materials are one of the most commonly used high-temperature insulation materials because of their high porosity and low thermal conductivity. Due to their wide applications in the aerospace and energy industries, the investigation of high-elastic thermally insulating porous materials has attracted increasing attention. In order to improve the elasticity of fibrous porous materials, quartz fibers with high aspect ratio were used as matrix, sodium hexametaphosphate (SHMP) was selected as dispersant. We innovatively reported that a unique three-dimensional skeleton structure was constructed by adjusting the dispersion of fibers in the slurry, and the lightweight, thermal insulating and elastic SiO2 fibrous porous material was then prepared by the compression molding method. The characterization results of zeta potential and absorbance showed that the addition of SHMP was an effective method to enhance the dispersibility of quartz fibers in the slurry. SiO2 fibrous porous materials with 0.4 wt% SHMP content exhibited an ideal three-dimensional skeleton structure, which endowed the porous material with high porosity (89.39%), low density (0.04751 g/cm3), and low thermal conductivity (0.0356 W·m−1·K−1). The three-dimensional skeleton structure formed by overlapping fibers with high aspect ratios endowed the porous material with excellent elasticity. SiO2 fibrous porous materials with 0.4 wt% SHMP content could undergo large strains of 30% and achieved a resilience ratio of 81.69% under the 30th compression cycle. Moreover, after heat treatment at 800 °C, SiO2 fibrous porous materials also maintained good elasticity with a resilience ratio of more than 80%. [ABSTRACT FROM AUTHOR]

Graphene quantum dot (GQD) is an emerging class of zero-dimensional nanocarbon material with many novel applications. It is of scientific importance to prepare GQDs with more perfect structures, that is, GQDs containing negligible oxygenous defects, for both optimizing their optical properties and helping in their photovoltaic applications. Herein, a new strategy for the facile preparation of "pristine" GQDs is reported. The method we presented is a combination of a bottom-up synthetic and a solvent-induced interface separation process, during which the target products with highly crystalline structure were selected by the organic solvent. The obtained organic soluble GQDs (O-GQDs) showed a significant difference in structure and composition compared with ordinary aqueous soluble GQDs, thus leading to a series of novel properties. Furthermore, O-GQDs were applied as electron-acceptors in a poly(3-hexylthiophene) (P3HT)-based organic photovoltaic device. The performance highlights that O-GQD has potential to be a novel electron-acceptor material due to the sp(2) hybridized carbon atom dominant structure and good solubility in organic solvents.