Search

This study investigates the impact of varying extrusion ratios on the microstructure and mechanical properties of AlSiCuFeMnYb alloy. Following hot extrusion, significant enhancements are observed in the microstructure of the cast rare earth aluminium alloy. Within the cross-sectional microstructure, the α-Al phase is reduced in size, and its dendritic morphology is eliminated. The morphology of the eutectic Si phase transitions from long strips to short rods, fine fibres, or granular forms. Similarly, the Fe-rich phase changes from a coarse skeletal and flat noodle shape to small strips and short skeletal forms resembling Chinese characters. The CuAl2 phase evolves from large blocks to smaller blocks and granular forms, while the Yb (Ytterbium)-rich rare earth phase shifts from large blocks to smaller, more uniformly distributed blocks. In the longitudinal section, the structure aligns into strips along the extrusion direction, with the spacing between these strips decreasing as the extrusion ratio increases. At an extrusion ratio of 22.56, the alloy demonstrates superior mechanical properties with a tensile strength of 325.50 MPa, a yield strength of 254.44 MPa, a hardness of 143.90 HV, and an elongation of 15.47%. These represent improvements of 27.8%, 36.5%, 38.9%, and 236.4%, respectively, compared with the as-cast rare earth alloy. In addition, the fracture surface of the extruded rare earth alloy exhibits obvious ductile fracture characteristics. Additionally, the alloy undergoes dynamic recrystallisation and dislocation entanglement during hot extrusion. The emergence of a twinned Si phase and a dynamically precipitated nanoscale CuAl2 phase are critical for enhancing deformation strengthening, modification strengthening, and dynamic precipitation strengthening of the extruded alloys. [ABSTRACT FROM AUTHOR]

With the development of technology, people's demand for pressure sensors with high sensitivity and a wide working range is increasing. An effective way to achieve this goal is simulating human skin. Herein, we propose a facile, low-cost, and reproducible method for preparing a skin-like multi-layer flexible pressure sensor (MFPS) device with high sensitivity (5.51 kPa−1 from 0 to 30 kPa) and wide working pressure range (0–200 kPa) by assembling carbonized fabrics and micro-wrinkle-structured Ag@rGO electrodes layer by layer. In addition, the highly imitated skin structure also provides the device with an extremely short response time (60/90 ms) and stable durability (over 3000 cycles). Importantly, we integrated multiple sensor devices into gloves to monitor finger movements and behaviors. In summary, the skin-like MFPS device has significant potential for real-time monitoring of human activities in the field of flexible wearable electronics and human–machine interaction. [ABSTRACT FROM AUTHOR]

In order to study the adsorption process and adsorption characteristics of shale oil at the macro scale, the isothermal adsorption experiments of illite and kerogen on a heptadecane (oil phase) solution were carried out by infrared spectrophotometry and gas chromatography–mass spectrometry. Based on the adsorption isotherm model and adsorption thermodynamic model, the characteristics of heptadecane adsorbed by illite and kerogen at different temperatures and oily solution concentrations were studied. The experimental results show that the concentration and temperature of the alkane solution help to enhance the adsorption and increase the saturated adsorption capacity. The difference is that the concentration will have a certain effect on the adsorption rate, while the temperature will not. Based on the three adsorption isotherm models, it was found that Langmuir and Freundlich were more suitable for describing the adsorption process of the heptadecane solution by illite and kerogen, and the adsorption characteristics of heptadecane molecules at different temperatures and adsorbents were evaluated. Heating leads to an increase in the collision efficiency between adsorbate molecules and adsorbents, thereby accelerating the migration rate of alkanes. Therefore, increasing temperature helps to enhance the adsorption capacity of rocks and increase the saturated adsorption capacity of minerals. The research results clarify the adsorption characteristics of shale oil heavy components from the macro level and fill the research gap in the application of solid–liquid isothermal adsorption physical experiments on the adsorption and occurrence of shale oil. [ABSTRACT FROM AUTHOR]

To remove the metronidazole, the iron oxides loaded on granular activated carbon (FeOx-GAC) were prepared by the impregnation–calcination approach. The physicochemical properties of the catalysts were characterized by electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The results show that FeOx-GAC has a porous structure, in which the iron oxides with a variety of valence states are smoothly attached on the activated carbon. The catalytic activity of FeOx-GAC was evaluated for metronidazole removal, exhibiting great catalytic efficiency of the catalyst. Besides, the catalytic ozonation of metronidazole was optimized by varying the dose of ozone and catalyst, as well as the pH of the solution. [ABSTRACT FROM AUTHOR]