Search

The quest for better nutritious foods has encouraged novel scientific investigations to find trans-fat reduction methods. This research proposes an innovative approach for the production of healthier trans-fat-free margarine from palm oil by the use of dielectric barrier discharge (DBD) plasma technology with glycerol serving as the principal source of hydrogen. The effectiveness of DBD plasma in hydrogenating palm olein was investigated. By employing a methodical series of experiments and thorough analytical approaches, examination of the saturated fatty acid conversion experienced its iodine value (IV) reduction from 67.16 ± 0.70 to 31.61 ± 1.10 under the optimal process parameters of 1 L min-1 He flow rate, 35 W plasma discharge power, 10 mm gap size, ambient initial temperature, and 12 h reaction time with solid texture. According to the method for producing trans-fat-free margarine in the absence of a catalyst and H2 gas, the hydrogenation rate of the prepared mixture of palm olein-glycerol was remarkably improved; the trans-fat content in the produced product was zero; the efficacy of incorporating cis- and trans-isomerization was lowered, and the method has a promising industrial application prospect.

Adsorption is regarded as an efficient method to eliminate per- and polyfluoroalkyl substances from an aqueous solution. In the present investigation, an adsorbent based on rice husks (RHs) was successfully prepared by phosphoric acid (PA) activation and dielectric barrier discharge (DBD) plasma treatment, and it was used to adsorb perfluorooctanoic acid (PFOA) from water. The electrodes employed in the experiment were planar type. This research investigated RH surface properties and adsorption capacity before and after modification using DBD plasma. The results revealed that the He-O2 plasma modification introduced oxygen-containing functional groups and increased the PFOA removal efficiency. Increasing the oxygen content and total gas flow rate to 30 vol.% and 1.5 L/min, respectively, with 10 min of RH plasma treatment time at 100 W plasma discharge power enhanced the PFOA removal efficiency to 92.0%, while non-treated RH showed the removal efficiency of only 46.4%. The removal efficiency of the solution increased to 96.7% upon adjusting the pH to 4. The adsorption equilibrium isotherms fitted the Langmuir model, and the adsorption kinetic followed the pseudo-second-order model. The maximum adsorption capacity was 565 mg/g when the Langmuir isotherm model was applied.

High rates of new cervical cancer cases and deaths occur in low- and middle-income countries yearly, and one reason was found related to limitation of regular cervical cancer screening in local and low-resource settings. HPV has over 150 types, yet certain 14-20 high-risk and 13-14 low-risk types are common, and, thus, most conventional HPV nucleic acid assays, for examples, Cobas 4800 HPV test (Roche Diagnostics, New Jersey, USA) and REBA HPV-ID (Molecules and Diagnostics, Wonju, Republic of Korea) were developed to cover these types. We thereby utilized bioinformatics combined with recent isothermal amplification technique at 35-42 °C to firstly describe multiplex recombinase polymerase amplification assay that is specific to these common 20 high-risk and 14 low-risk types, and also L1 and E6/E7 genes that target different stages of cervical cancer development. Multiplex primer concentrations and reaction incubation conditions were optimized to allow simultaneous two gene detections at limit of detection of 1000 copies (equivalent to 2.01 fg) for L1 and 100 copies (0.0125 fg) for E6/E7, respectively. The assay was validated against urogenital and other pathogens, normal flora, and human control. In 130 real clinical sample tests, the assay demonstrated 100% specificity, 78% diagnostic accuracy, and 75% sensitivity compared with REBA HPV-ID test, and is much more rapid (15-40 min), less expensive (~ 3-4 USD/reaction) and does not require instrumentation (35-42 °C reaction condition so hand holding or tropical temperature is possible). Hence, the developed novel assay provides alternative screening tool for potential local screening. Furthermore, as this assay uses safe chemical reagents, it is safe for users.

Fatty acid methyl esters (FAMEs) are sustainable biofuel that can alleviate high oil costs and environmental impacts of petroleum-based fuel. A modified 1200 W high-efficiency food blender was employed for continuous transesterification of various refined vegetable oils and waste cooking oil (WCO) using sodium hydroxide as a homogeneous catalyst. The following factors have been investigated on their effects on FAME yield: baffles, reaction volume, total reactant flow rate, methanol-oil molar ratio, catalyst concentration and reaction temperature. Results indicated that the optimal conditions were: 2000 mL reaction volume, 50 mL/min total flow rate, 1% and 1.25% catalyst concentration for refined palm oil and WCO, respectively, 6:1 methanol-to-oil molar ratio and 62-63 °C, obtaining yield efficiency over 96.5% FAME yield of 21.14 × 10-4 g/J (for palm oil) and 19.39 × 10-4 g/J (for WCO). All the properties of produced FAMEs meet the EN 14214 and ASTM D6751 standards. The modified household food blender could be a practical and low-cost alternative biodiesel production apparatus for continuous biodiesel production for small communities in remote areas.

Loop-mediated isothermal amplification (LAMP) has been widely used to detect many infectious diseases. However, minor inconveniences during the steps of adding reaction ingredients and lack of simple color results hinder point-of-care detection. We therefore invented a fluorometric paper-based LAMP by incorporating LAMP reagents, including a biotinylated primer, onto a cellulose membrane paper, with a simple DNA fluorescent dye incubation that demonstrated rapid and accurate results parallel to quantitative polymerase chain reaction (qPCR) methods. This technology allows for instant paper strip detection of methicillin-resistant Staphylococcus aureus (MRSA) in the laboratory and clinical samples. MRSA represents a major public health problem as it can cause infections in different parts of the human body and yet is resistant to commonly used antibiotics. In this study, we optimized LAMP reaction ingredients and incubation conditions following a central composite design (CCD) that yielded the shortest reaction time with high sensitivity. These CCD components and conditions were used to construct the paper-based LAMP reaction by immobilizing the biotinylated primer and the rest of the LAMP reagents to produce the ready-to-use MRSA diagnostic device. Our paper-based LAMP device could detect as low as 10 ag (equivalent to 1 copy) of the MRSA gene mecA within 36-43 min, was evaluated using both laboratory (individual cultures of MRSA and non-MRSA bacteria) and clinical blood samples to be 100% specific and sensitive compared to qPCR results, and had 35 day stability under 25 °C storage. Furthermore, the color readout allows for quantitation of MRSA copies. Hence, this device is applicable for point-of-care MRSA detection.

Perfluorooctanoic acid (PFOA), a widely used perfluorinated alkyl substance (PFAS), poses significant environmental and health risks. This study investigates PFOA adsorption in the existence of natural organic matter (NOM) using granular activated carbon (GAC) modified with dielectric barrier discharge (DBD) plasma. PFOA’s amphiphilic structure, characterized by a hydrophilic carboxyl group head and a hydrophobic perfluorinated tail, contributes to its versatility and persistence. The selection of the Chao Phraya River (CPR) water as the NOM source, captures the complexity of a major water body subjected to diverse pollution sources. The results were analyzed through the Toth and Temkin isotherm models. Application of the Toth isotherm model reveals enhanced PFOA adsorption capacity in CPR water compared to DI water, emphasizing the influence of NOM. The Temkin isotherm analysis further characterizes the strength and efficiency of the adsorption process, highlighting a stronger interaction between PFOA and plasma-modified GAC in CPR water. The study indicates that the adsorption process in CPR water may be more influenced by PFOA surface coverage on the GAC surface in the presence of NOM. Overall, this research contributes valuable insights into pollutant removal strategies, highlighting the potential of DBD plasma-modified GAC in addressing PFOA contamination challenges in water systems.