Search

This publication presents the effect of hypochlorous acid dry mist as a disinfectant on selected bacteria, viruses, spores, and fungi as well as on portable Microlife OXY 300 finger pulse oximeters and electronic systems of Raspberry Pi Zero microcomputers. The impact of hypochlorous acid on microbiological agents was assessed at concentrations of 300, 500, and 2000 ppm of HClO according to PN-EN 17272 (Variant I). Studies of the impact of hypochlorous acid fog on electronic components were carried out in an aerosol chamber at concentrations of 500 ppm and 2000 ppm according to two models consisting of 30 (Variant II) and 90 fogging cycles (Variant III). Each cycle included the process of generating a dry mist of hypochlorous acid (25 mL/m3), decontamination of the test elements, as well as cleaning the chamber of the disinfectant agent. The exposure of the materials examined on hypochlorous acid dry mist in all variants resulted in a decrease in the number of viruses, bacteria, spores, and fungi tested. In addition, the research showed that in the variants of hypochlorous acid fogging cycles analyzed, no changes in performance parameters and no penetration of dry fog of hypochlorous acid into the interior of the tested medical devices and electronic systems were observed.

. During shooting operations in garrison shooting ranges, a phenomenon of random deflection of the bullet flight path was noticed which may cause secondary reflections from accidentally hit technical and ballistic shooting range elements and the ground of the actual plane of the shooting range (ricochets posing a threat to people and property within the shooting range and safety zones). Minimisation of this phenomenon must be considered during the design and operation of the shooting ranges. In 20202022 the Military Institute of Armament Technology (Zielonka, Poland) carried out tests with the aim of determining the impact of the shooting target or military target material or design (hereinafter referred to as the targets) on the risk of occurrence of modifications of bullet trajectory that cause the bullets to leave the shooting zone. The paper presents example results of these tests that show, but are not limited to, that the reasons to modify the direction of the bullet path after target penetration and any ricochets include: target material (flat or corrugated sheet metal, cardboard, plywood, etc.), target wooden legs, and even metal elements fixing the legs to the target. On the basis of the test it was shown that the metal targets prohibited on intermediate lines may cause significant deflections of the bullet flight path after penetration and dangerous ricochets. Due to the reason presented above, the metal targets are placed on the last line of targets before the main bullet trap only where the technical and ballistic parameters of the bullet trap ensure that any ricochets are captured. It was stated that the contact targets used on intermediate target lines and provided with wooden legs may cause bullet trajectory changes comparable to or even greater than in the case of the prohibited metal targets. To this end it is advisable to establish legal framework covering the ballistic inspection of the target materials to be used in garrison shooting ranges.

This paper presents a concept for shielding the MSBS (Modular Firearms System) Grot rifle upper receiver against foreign objects. The concept guidelines involve feedback from Grot operators concerning the regular operation of the rifle plus an extensive analysis of desktop patent research into foreign debris shields (or dust shields) for protection of the upper receiver interior in firearms. The completed patent desktop research included solutions used with automatic, semi-automatic and non-automatic firearms. The research work drove the formulation of the requirements for an upper receiver dust shield for the 5.56 mm calibre MSBS Grot rifle as part of the ongoing improvement process. This paper presents three concepts of the carrier charging handle assembly dust shield (for the protection of the upper receiver against foreign objects) for the MSBS-5.56 rifle system. The concepts described vary in terms of the level of structural complexity of the dust shield, and the extent of the modifications required to the upper receiver of the rifle. With test units of the upper receiver dust shield manufactured and comparative tests completed on the three concepts, the version selected should be the one which improves the protection of the rifle internals from foreign objects found in the local environment, including sand, clay, silt, and mud, the latter being an aqueous suspension of these particles.

The formation of craters is an important issue in the investigations of the surface of the earth and other planets. The aim of the study was to check whether the different textures of sand beds affect the size and dynamics of the formation of craters and ejection curtain after high-velocity impacts. The experiments were conducted using an aluminium impactor at two impact speeds (~700 and ~1300 m∙s-1) and a sand bed composed of either a broad range of sizes (

The development of unmanned air vehicles (UAVs) has been very rapid recently. The wide accessibility of UAVs has unlocked a great potential for the malicious or accidental damage or destruction of property or other aircraft in flight. UAVs can be used for espionage, contraband, and the trafficking or transport of arms and hazardous materials. Every month sees a growing number of reports of incidents that involve remote-controlled UAVs operated for aerial video recording. These incidents justify undertaking research into minimizing the hazards which UAVs may potentially cause. A concept was developed for a solution dedicated to this problem and comprising an integrated modular anti-UAV system for application in commercial (civilian) markets in the areas of security of mass events, strategic enterprises, and critical strategic infrastructure in Poland. The proposed system is intended to incapacitate any UAVs that breach a predefined air space and bring the incapacitated UAVs safely to the ground. The project is developed jointly by the Institute of Armament Technology at the Military University of Technology (Warsaw, Poland) and Polish company Ellipsis Sp. z o.o.

In the presented paper, kinematic characteristics of movable parts of investigated pistols have been experimentally determined with application of high speed camera and appropriate software TEMA motion. Results of measurements can be useful in validation of various theoretical models and can reveal the influence of some technical solutions on parameters of motion of selected parts. Obtained curves presenting dependence of slide velocity versus time, allowed for rough estimation of average value of interaction force between slide and frame of the investigated construction. The results of study highlights advantage of HK USP pistol design. The achieved results are from reduction of the value of the mentioned interaction force (approximately 50%) due to elongation of the most intensive phase of slide motion damping process.