Search

Wound healing can be delayed if the biomechanical stability of the wound closure is inadequate. Therefore, it is necessary to investigate different suturing techniques for their biomechanical stability. In this study, suturing techniques suitable for the forehead area were investigated. For this application, a special test setup was developed to simulate the curvature of the forehead and the corresponding physiological configuration. The average forehead curvature is 62.24 ± 4.11 mm in radius. To simulate this curvature, the skin specimens are subjected to tensile stress over the spherical surface using a standard uniaxial testing machine. For the evaluation, an automated evaluation tool for MATLAB was also developed. Three different suturing techniques (Straight, Lazy-S, Zigzag) were investigated and tested for their biomechanical stability. Of the three suturing techniques, the Zigzag suture proved to be the most stable with the highest stiffness of 44.23 ± 8.18 % and the highest final failure of 32.60 ± 4.95 % (relative to the control sample without incision). The study has shown that the test setup can be used to investigate different forehead suture techniques.

Introduction: Osteosynthesis of the equine femur is still a challenge for veterinary medicine. Even though intramedullary fracture fixation is possible nowadays, the varying geometry of the medullary cavity along the bone axis is a critical factor. Limited contact area between implant and bone can cause insufficient primary stability. In this study, it was investigated whether the osteosynthesis stability can be improved with a form-adaptive reinforcement for the diaphyseal part of the proximal fragment. Material and Methods: Eight equine femora were fitted with intramedullary nail osteosynthesis and analyzed by 4-point bending. Virtual position planning of the ex-vivo implantation using CT-data increased comparability. For five femora the proximal fragment was reinforced with a flexible polymer mixture. Longterm stability was tested via cyclic loading. Bending stiffness and its development due to cyclic loading was evaluated before and after reinforcement procedure. Finally, load-to-failure was tested in the same setup. Results and Discussion: The application of the polymer reinforcement increased the maximum torque in the load-tofailure measurement by 26%. Bending stiffness was not affected in the measured loading range by the reinforcement. Cyclic loading increased bending stiffness for a conditioned state but showed to be reversible for the most part. Conclusion: The fracture adjacent reinforcement showed to be beneficial to the osteosynthesis stability, but further investigation is necessary for surgical application.

For the development of new types of hip implants for acetabulum revision, it is beneficial to analyse the acetabular defects of the indication group in advance. In order to be able to specially compare the bone defects with each other, a normalisation and accompanying scaling of the pelvis is necessary. Uniform scaling is required so that the bone structures are not distorted. In the following study, three scaling methods based on the minimal bounding box and sphere principle are compared with a method using 14 landmarks on the pelvis.The landmark method is applied to determine the true scaling factor. For the comparison of the different methods, 40 female pelvic models with an acetabular defect are analysed. In the comparison of the scaling methods, the method using minimal bounding spheres shows the least deviation from the landmark method (mean difference 3.30 ± 2.17 %). Due to the fact that no preprocessing (definition of the landmarks) is required and the fast implementation of the algorithm, the minimal bounding sphere is to be preferred to the landmark method for a fast size estimation.

Bioreactors with a controlled physiological environment are being developed to study various cell processes. The influences of mechanostimulation on bone cell cultures can be investigated using a compression bioreactor. The developed bioreactor system applies a cyclic compression force to the specimen via an eccentrically mounted push rod. The compression force is monitored by a force sensor to detect changes in the material properties of the specimen. Depending on the piston setting, a stroke of 0.28 - 2.50 mm can be applied to the specimen. The bioreactor system was tested with a trial run of 18 days. A sample was continuously stimulated with a loading frequency of 2 Hz and a stroke of 1.50 mm. The sterility in the cell chamber as well as the functionality of the realised bioreactor stimulation system could be successfully confirmed