Search

Subject-specific computational models of anatomical components can now be generated from image data and used in the assessment of orthopaedic interventions. However, little work has been undertaken to model cement-augmented bone using these methods. The purpose of this study was to investigate different methods of representing a trabecular-like material (open-cell polyurethane foam, Sawbone, Sweden) augmented with poly(methyl methacrylate) (PMMA) bone cement in a finite element (FE) model. Three sets of specimens (untreated, fully augmented with cement, partially augmented with cement) were imaged using micro computed tomography (microCT) and tested under axial compression. Subject-specific continuum level FE models were built based on the microCT images. Using the first two sets of models, the material conversion factors between image greyscale and mechanical properties for the pure synthetic bone and cement-augmented composite were determined iteratively by matching the FE predictions to the experimental measurements. By applying these greyscale related mechanical properties to the FE models of the partially augmented specimens, the predicted stiffness was found to be more accurate (approximately 5 per cent error) than using homogeneous properties for the augmented and synthetic bone regions (approximately 18 per cent error). It was also found that the predicted stiffness using the modulus of pure cement to define the augmented region was overestimated, and generally the apparent elastic modulus was dominated by the properties of the synthetic bone. [ABSTRACT FROM AUTHOR]

The aim of this study was to determine the accuracy of specimen-specific finite element models of untreated and cement-augmented vertebrae by direct comparison with experimental results. Eleven single cadaveric vertebrae were imaged using micro computed tomography (microCT) and tested to failure in axial compression in the laboratory. Four of the specimens were first augmented with PMMA cement to simulate a prophylactic vertebroplasty. Specimen-specific finite element models were then generated using semi-automated methods. An initial set of three untreated models was used to determine the optimum conversion factors from the image data to the bone material properties. Using these factors, the predicted stiffness and strength were determined for the remaining specimens (four untreated, four augmented). The model predictions were compared with the corresponding experimental data. Good agreement was found with the non-augmented specimens in terms of stiffness (root-mean-square (r.m.s.) error 12.9 per cent) and strength (r.m.s. error 14.4 per cent). With the augmented specimens, the models consistently overestimated both stiffness and strength (r.m.s. errors 65 and 68 per cent). The results indicate that this method has the potential to provide accurate predictions of vertebral behaviour prior to augmentation. However, modelling the augmented bone with bulk material properties is inadequate, and more detailed modelling of the cement region is required to capture the bone-cement interactions if the models are to be used to predict the behaviour following vertebroplasty. [ABSTRACT FROM AUTHOR]

The principles of solid mechanics have many important applications in orthopaedics. The aim of this paper is to cover the basic concepts of statics and dynamics, including both kinetics and kinematics. The equations most commonly used in biomechanical analysis are introduced and examples are given of their use in orthopaedic applications. [ABSTRACT FROM AUTHOR]

Osteochondral grafting has demonstrated positive outcomes for treating articular cartilage defects by replacing the damaged region with a cylindrical graft consisting of bone with a layer of cartilage. However, factors that cause graft subsidence are not well understood. The aim of this study was to develop finite element (FE) models of osteochondral grafts within a tibiofemoral joint, suitable for an investigation of parameters affecting graft stability. Cadaveric femurs were used to experimentally calibrate the bone properties and graft-bone frictional forces for use in corresponding image-based FE models, generated from µCT scan data. Effects of cartilage defects and osteochondral graft repair were measured by examining contact pressure changes using further in vitro tests. Here, six defects were created in the femoral condyles, which were subsequently treated with osteochondral autografts or metal pins. Matching image-based FE models were created, and the contact patches were compared. The bone material properties and graft-bone frictional forces were successfully calibrated from the initial tests with good resulting levels of agreement (CCC = 0.87). The tibiofemoral joint experiment provided a range of cases that were accurately described in the resultant pressure maps and were well represented in the FE models. Cartilage defects and repair quality were experimentally measurable with good agreement in the FE model pressure maps. Model confidence was built through extensive validation and sensitivity testing. It was found that specimen-specific properties were required to accurately represent graft behaviour. The final models produced are suitable for a range of parametric testing to investigate immediate graft stability., (© 2024. The Author(s).)

Objectives: Fresh-frozen allograft is the gold-standard bone graft material used during revision hip arthroplasty. However, new technology has been developed to manufacture decellularised bone with potentially better graft incorporation. As these grafts cost more to manufacture, the aim of this cost-effectiveness study was to estimate whether the potential health benefit of decellularised bone allograft outweighs their increased cost., Study Design: A Markov model was constructed to estimate the costs and the quality-adjusted life years of impaction bone grafting during a revision hip arthroplasty., Setting: This study took the perspective of the National Health Service in the UK., Participants: The Markov model includes patients undergoing a revision hip arthroplasty in the UK., Intervention: Impaction bone grafting during a revision hip arthroplasty using either decellularised bone allograft or fresh-frozen allograft., Measures: Outcome measures included: total costs and quality-adjusted life years of both interventions over the lifetime of the model; and incremental cost-effectiveness ratios for both graft types, using base case parameters, univariate sensitivity analysis and probabilistic analysis., Results: The incremental cost-effectiveness ratio for the base case model was found to be £270 059 per quality-adjusted life year. Univariate sensitivity analysis found that changing the discount rate, the decellularised bone graft cost, age of the patient cohort and the revision rate all had a significant effect on the incremental cost-effectiveness ratio., Conclusions: As there are no clinical studies of impaction bone grafting using a decellularised bone allograft, there is a high level of uncertainty around the costs of producing a decellularised bone allograft and the potential health benefits. However, if a decellularised bone graft was manufactured for £2887 and lowered the re-revision rate to less than 64 cases per year per 10 000 revision patients, then it would most likely be cost-effective compared with fresh-frozen allograft., Competing Interests: Competing interests: None declared., (© Author(s) (or their employer(s)) 2023. Re-use permitted under CC BY. Published by BMJ.)

Self-assembling peptides are a promising biomaterial with potential applications in medical devices and drug delivery. In the right combination of conditions, self-assembling peptides can form self-supporting hydrogels. Here, we describe how balancing attractive and repulsive intermolecular forces is critical for successful hydrogel formation. Electrostatic repulsion is tuned by altering the peptide's net charge, and intermolecular attractions are controlled through the degree of hydrogen bonding between specific amino acid residues. We find that an overall net peptide charge of +/-2 is optimal to facilitate the assembly of self-supporting hydrogels. If the net peptide charge is too low then dense aggregates form, while a high molecular charge inhibits the formation of larger structures. At a constant charge, altering the terminal amino acids from glutamine to serine decreases the degree of hydrogen bonding within the assembling network. This tunes the viscoelastic properties of the gel, reducing the elastic modulus by two to three orders of magnitude. Finally, hydrogels could be formed from glutamine-rich, highly charged peptides by mixing the peptides in combinations with a resultant net charge of +/-2. These results illustrate how understanding and controlling self-assembly mechanisms through modulating intermolecular interactions can be exploited to derive a range of structures with tuneable properties.

Finite element models (FEMs) of the spine commonly use a limited number of simplified geometries. Nevertheless, the geometric features of the spine are important in determining its FEM outcomes. The link between a spinal segment's shape and its biomechanical response has been studied, but the co-variances of the shape features have been omitted. We used a principal component (PCA)-based statistical shape modelling (SSM) approach to investigate the contribution of shape features to the intradiscal pressure (IDP) and the facets contact pressure (FCP) in a cohort of synthetic L4/L5 functional spinal units under axial compression. We quantified the uncertainty in the FEM results, and the contribution of individual shape modes to these results. This parameterisation approach is able to capture the variability in the correlated anatomical features in a real population and sample plausible synthetic geometries. The first shape mode ([Formula: see text]) explained 22.6% of the shape variation in the subject-specific cohort used to train the SSM, and had the largest correlation with, and contribution to IDP (17%) and FCP (11%). The largest geometric variation in ([Formula: see text]) was in the annulus-nucleus ratio., (© 2022. The Author(s).)

Osteoarthritis (OA) is the most prevalent chronic rheumatic disease worldwide with knee OA having an estimated lifetime risk of approximately 14%. Autologous osteochondral grafting has demonstrated positive outcomes in some patients, however, understanding of the biomechanical function and how treatments can be optimised remains limited. Increased short-term stability of the grafts allows cartilage surfaces to remain congruent prior to graft integration. In this study methods for generating specimen specific finite element (FE) models of osteochondral grafts were developed, using parallel experimental data for calibration and validation. Experimental testing of the force required to displace osteochondral grafts by 2 mm was conducted on three porcine knees, each with four grafts. Specimen specific FE models of the hosts and grafts were created from registered μCT scans captured from each knee (pre- and post-test). Material properties were based on the μCT background with a conversion between μCT voxel brightness and Young's modulus. This conversion was based on the results of the separate testing of eight porcine condyles and optimization of specimen specific FE models. The comparison between the experimental and computational push-in forces gave a strong agreement with a concordance correlation coefficient (CCC) = 0.75, validating the modelling approach. The modelling process showed that homogenous material properties based on whole bone BV/TV calculations are insufficient for accurate modelling and that an intricate description of the density distribution is required. The robust methodology can provide a method of testing different treatment options and can be used to investigate graft stability in full tibiofemoral joints., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2022 The Authors. Published by Elsevier Ltd.. All rights reserved.)

Involving research users in setting priorities for research is essential to ensure the outcomes are patient-centred and maximise its value and impact. The Musculoskeletal Disorders Research Advisory Group Versus Arthritis led a research priority setting exercise across musculoskeletal disorders. The Child Health and Nutrition Research Initiative (CHNRI) method of setting research priorities with a range of stakeholders was used, involving four stages and two surveys, to: (1) gather research uncertainties, (2) consolidate these, (3) score uncertainties against importance and impact, and (4) analyse scoring for prioritisation. 213 people responded to the first survey and 285 people to the second, representing clinicians, researchers, and people with musculoskeletal disorders. Key priorities included developing and testing new treatments, better treatment targeting, early diagnosis, prevention, and better understanding and management of pain, with an emphasis on understanding underpinning mechanisms. We present a call to action to researchers and funders to target these priorities., Competing Interests: FEW reports grants from UK Research and Innovation (UKRI), National Institute for Health and Care Research (NIHR), Versus Arthritis, Medical Research Council (MRC); consulting fees from Pfizer; and committee role for MRC and NIHR. ZP reports grants from NIHR, Versus Arthritis, Royal Osteoporosis Society, General Council for Nursing, Haywood Foundation, Chartered Society for Physiotherapy, and British Society for Rheumatology; honoraria from the Royal College of General Practitioners; non-paid consultancy for UCB, and unpaid committee roles with Royal Osteoporosis Society and Haywood Foundation. CB reports grants from Versus Arthritis and University of Liverpool (Liverpool, UK). EMC reports grants from Royal Osteoporosis Society, Elizabeth Blackwell Institute (University of Bristol, Bristol, UK) MRC Confidence in Concept Award, NIHR, Southmead Hospital Charity Research Fund, Healthcare Quality Improvement Partnership; payment or honoraria from Danske Fysioterapeuter and Journal of Bone and Mineral Research Plus; and an unpaid committee role with the Royal Osteoporosis Society. MG reports grants from Versus Arthritis and Clarendon Fund. RKJ reports grants from the Ministry of Defence. CLLM reports grants from H2020 ITN, Disc4All, Flexion Plc (Contract Research Funding), Engineering and Physical Sciences Research Council (EPSRC), MRC, and Versus Arthritis; consultancy fees and royalties or licensing fees from Flexion; committee roles for JOR Spine, Discovering Innovative Solutions for Conditions of the Spine, and Society of Back Pain Research. JL reports grants from MRC, The John George William Patterson Foundation, and the Ruth & Lionel Jacobson Charitable Trust. DJM reports grants from Orphelion, Innovation for All, Welsh Government with Knoell, Versus Arthritis, KESS2 & Hospital Innovations, EPSRC, Wellcome Trust Collaborative Award, Petplan Charitable Trust, and British Veterinary Orthopaedic Association; payment or honorarium from Eli Lilly; receipt of drugs from Novartis; participation on a data safety oversight board for NIHR (paid) and Innovative Medicines Initiative (paid), unpaid leadership role within British Orthopaedic Research Society and Orthopaedics Research Society, and paid committee role in Science Foundation Ireland Early Career Panel. NLM reports grants from MRC and Chan Zuckerberg Initiative. HP reports grants from Knowledge Transfer Partnership–Innovate UK, Pacira Pharmaceuticals, Zimmer Biomet Healthcare, B Braun, and Wellcome Trust; consulting fees from Medacta International, Smith and Nephew, Depuy Synthes, JRI Orthopaedics, Janssen, Meril Life, Zimmer Biomet, and Paradigm Pharmaceuticals; payment or honoraria from Invibio; payment for expert testimony from Kennedy's Law; support for attending meetings from Medacta International; participation on data safety oversight board for GreenBric Study; unpaid committee role for NIHR and National Joint Registry Regional Clinical Coordinators; and receipt of drug from Pacira Pharmaceuticals. GP reports grants from NIHR, Nuffield Foundation, and Versus Arthritis, and consulting fees from Office Health Inequalities & Disparities; participation on data safety monitoring board and role as Lancet Osteoarthritis Commissioner. SMR reports grants from Versus Arthritis and Wellcome Trust, honoraria from Portugal grant review, and had a role as treasurer and committee member for the Tissue and Cell Engineering Society. EJS reports grants from NHSX and committee role on musculoskeletal reform. LT reports grants from Versus Arthritis, The Macular Society, MRC, Rosetrees Trust, University of East Anglia Faculty of Medicine and Health Sciences (Norwich, UK), and the Kennedy Institute of Rheumatology; support for attending meetings from Advanced Course–Matrix Pathobiology, Signalling and Molecular Targets, and OACON 2019. RKW reports grants from EPSRC, DePuy Synthes, and Versus Arthritis; unpaid committee role in Royal Academy of Engineering; and receipt of materials from DePuy synthesis. CW reports support for attending meetings from European Pain Federation; participation on advisory board for University of Swansea (Swansea, UK), Health Data Research UK, and National Institute for Health and Care Excellence; and committee role for Versus Arthritis and University of Bath (Bath, UK). CF is employed by Versus Arthritis. All other authors declare no competing interests., (© 2022 The Author(s). Published by Elsevier Ltd. This is an Open Access article under the CC BY 4.0 license.)

Back pain affects a person's health and mobility as well as being associated with large health and social costs. Lower back pain is frequently caused by degeneration of the intervertebral disc. Current operative and non-operative treatments are often ineffective and expensive. Nucleus augmentation is designed to be a minimally invasive method of restoring the disc to its native healthy state by restoring the disc height, and mechanical and/or biological properties. The majority of the candidate materials for nucleus augmentation are injectable hydrogels. In this review, we examine the materials that are currently under investigation for nucleus augmentation, and compare their ability to meet the design requirements for this application. Specifically, the delivery of the material into the disc, the mechanical properties of the material and the biological compatibility are examined. Recommendations for future testing are also made.

Total Hip Arthroplasty (THA) is one of the most common and successful surgical interventions. The survivorship at 10 years for the most commonly used systems is over 95%. However, the incidence of revision is usually much higher in the 0-1 year time period following the intervention. The most common reason for revision in this early time period is dislocation and subluxation, which may be defined as complete or permanent, and partial or temporary loss of contact between the bearing surfaces respectively. This study comprises the development of a geometric model of bone and an in situ total hip replacement, to predict the occurrence and location of bone and component impingement for a wide range of acetabular cup positions and for a series of frequently practiced activities of daily living. The model developed predicts that anterior-superior component impingement is associated with activities that result in posterior dislocation. The incidence may be reduced by increased cup anteversion and inclination. Posterior-inferior component impingement is associated with anterior dislocation activities. Its incidence may be reduced by decreased cup anteversion and inclination. A component impingement-free range was identified, running from when the cup was positioned with 45° inclination and 25° anteversion to 70° inclination and 15°-20° anteversion.

Patient variation affects the outcomes of a range of spinal interventions, from disc replacement to vertebral fixation and vertebroplasty. Statistical Shape and Appearance Modelling (SSAM) can be used to describe anatomical variation and pathological differences within the population. To better understand how bone density and shape variation affect load transfer with respect to surgical treatments, Finite Element (FE) models can be generated from a SSAM. The aim for this study is to understand whether geometric and density variation as well as multiple vertebral levels can be incorporated into a single SSAM and whether this can be used to investigate the relationships between, and effects of, the various modes of variation. FE models of 14 human lumbar vertebrae that had been μCT imaged and validated through experimental testing were used as input specimens for a SSAM. The validity of the SSAM was evaluated by using principal component analysis to identify the primary modes of geometric and bone density variation and comparing to those in the input set. FE models were generated from the SSAM to examine the response to loading. The mean error between the input set and generated models for volume, mean density and FE compressive stiffness were 10%, 3% and 10% respectively. Principal Component (PC) 1 captured the majority of the bone density variation. The remaining PCs described specific geometric variation. The FE models generated from the SSAM showed the variations in vertebral stiffness as a result of complex relationships between bone density and shape. The SSAM created has limited data for its input set, however, it acts as a proof of concept for the novel combination of material and shape variation into a single shape model. This approach and the tools developed can be applied to wider patient groups and treatment scenarios to improve patient stratification and to optimise treatments., (Copyright © 2022 The Authors. Published by Elsevier Ltd.. All rights reserved.)

Many early stage interventions for intervertebral disc degeneration are under development involving injection of a biomaterial into the affected tissue. Due to the complex mechanical behaviour of the intervertebral disc, there are challenges in comprehensively evaluating the performance of these injectable biomaterials in vitro. The aim of this review was to examine the different methods that have been developed to mechanically test injectable intervertebral disc biomaterials in an in vitro disc model. Testing methods were examined with emphasis on overall protocol, artificial degeneration method, mechanical testing regimes and injection delivery. Specifically, the effects of these factors on the evaluation of different aspects of device performance was assessed. Broad testing protocols varied between studies and enabled evaluation of different aspects of an injectable treatment. Studies employed artificial degeneration methodologies which were either on a macro scale through mechanical means or on a microscale with biochemical means. Mechanical loading regimes differed greatly across studies, with load being either held constant, ramped to failure, or applied cyclically, with large variability on all loading parameters. Evaluation of the risk of herniation was possible by utilising ramped loading, whereas cyclic loading enabled the examination of the restoration of mechanical behaviour for initial screening of biomaterials and surgical technique optimisation studies. However, there are large variations in the duration or tests, and further work is needed to define an appropriate number of cycles to standardise this type of testing. Biomaterial delivery was controlled by set volume or haptic feedback, and future investigations should generate evidence applying physiological loading during injection and normalisation of injection parameters based on disc size. Based on the reviewed articles and considering clinical risks, a series of recommendations have been made for future intervertebral disc mechanical testing., (Copyright © 2021 The Authors. Published by Elsevier Ltd.. All rights reserved.)

After hip replacement, in cases where there is instability at the joint, contact between the femoral head and the acetabular liner can move from the bearing surface to the liner rim, generating edge loading conditions. This has been linked to polyethylene liner fracture and led to the development of a regulatory testing standard (ISO 14242:4) to replicate these conditions. Performing computational modelling alongside simulator testing can provide insight into the complex damage mechanisms present in hard-on-soft bearings under edge loading. The aim of this work was to evaluate the need for inertia and elastoplastic material properties to predict kinematics (likelihood of edge loading) and plastic strain accumulation (as a damage indicator). While a static, rigid model was sufficient to predict kinematics for experimental test planning, the inclusion of inertia, alongside elastoplastic material, was required for prediction of plastic strain behaviour. The delay in device realignment during heel strike, caused by inertia, substantially increased the force experienced during rim loading (e.g. 600 N static rigid, ∼1800 N dynamic elastoplastic, in one case). The accumulation of plastic strain is influenced by factors including cup orientation, swing phase force balance, the moving mass, and the design of the device itself. Evaluation of future liner designs could employ dynamic elastoplastic models to investigate the effect of design feature changes on bearing resilience under edge loading., (Copyright © 2021 The Authors. Published by Elsevier Ltd.. All rights reserved.)

Self-assembling hydrogels are promising materials for regenerative medicine and tissue engineering. However, designing hydrogels that replicate the 3-4 order of magnitude variation in soft tissue mechanics remains a major challenge. Here hybrid hydrogels are investigated formed from short self-assembling β-fibril peptides, and the glycosaminoglycan chondroitin sulfate (CS), chosen to replicate physical aspects of proteoglycans, specifically natural aggrecan, which provides structural mechanics to soft tissues. Varying the peptide:CS compositional ratio (1:2, 1:10, or 1:20) can tune the mechanics of the gel by one to two orders of magnitude. In addition, it is demonstrated that at any fixed composition, the gel shear modulus can be tuned over approximately two orders of magnitude through varying the initial vortex mixing time. This tuneability arises due to changes in the mesoscale structure of the gel network (fibril width, length, and connectivity), giving rise to both shear-thickening and shear-thinning behavior. The resulting hydrogels range in shear elastic moduli from 0.14 to 220 kPa, mimicking the mechanical variability in a range of soft tissues. The high degree of discrete tuneability of composition and mechanics in these hydrogels makes them particularly promising for matching the chemical and mechanical requirements of different applications in tissue engineering and regenerative medicine., (© 2021 The Authors. Advanced Healthcare Materials published by Wiley-VCH GmbH.)

Finite element modelling of the spinal unit is a promising preclinical tool to assess the biomechanical outcome of emerging interventions. Currently, most models are calibrated and validated against range of motion and rarely directly against soft-tissue deformation. The aim of this contribution was to develop an in vitro methodology to measure disc bulge and assess the ability of different specimen-specific modelling approaches to predict disc bulge. Bovine bone-disc-bone sections ( N = 6) were prepared with 40 glass markers on the intervertebral disc surface. These were initially magnetic resonance (MR)-imaged and then sequentially imaged using peripheral-qCT under axial compression of 1 mm increments. Specimen-specific finite-element models were developed from the CT data, using three different methods to represent the nucleus pulposus geometry with and without complementary use of the MR images. Both calibrated specimen-specific and averaged compressive material properties for the disc tissues were investigated. A successful methodology was developed to quantify the disc bulge in vitro , enabling observation of surface displacement on qCT. From the finite element model results, no clear advantage was found in using geometrical information from the MR images in terms of the models' ability to predict stiffness or disc bulge for bovine intervertebral disc., Competing Interests: The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest., (Copyright © 2021 Mengoni, Zapata-Cornelio, Wijayathunga and Wilcox.)

Intervertebral disc (IVD) degeneration is a major cause of back pain. Current surgical interventions have limitations. An alternative approach is to replace degenerated IVDs with a natural biological scaffold. The removal of cellular components from human IVDs should render them nonimmunogenic upon implantation. The aim of this initial proof of technical feasibility study was to develop a decellularization protocol on bovine IVDs with endplates (EPs) and assess protocol performance before application of the protocol to human IVDs with attached EP and vertebral bone (VB). A decellularization protocol based on hypotonic low concentration sodium dodecyl sulfate (0.1% w/v) with proteinase inhibitors, freeze/thaw cycles, and nuclease and sonication treatments was applied to IVDs. Histological, biochemical, and biomechanical comparisons were made between cellular and decellularized tissue. Cell removal from bovine IVDs was demonstrated and total DNA levels of the decellularized inner annulus fibrosus (iAF), outer annulus fibrosus (oAF), and EP were 40.7 (±11.4), 25.9 (±3.8), and 29.3 (±3.1) ng.mg -1 dry tissue weight, respectively ( n  = 6, ±95% confidence level [CL]). These values were significantly lower than in cellular tissue. No significant difference in DNA levels between bovine cellular and decellularized nucleus pulposus (NP) was found. Glycosaminoglycans (GAGs) were largely retained in the NP, iAF, and oAF. Cyclic compression testing showed sufficient sensitivity to detect an increase in stiffness of bovine IVD postdecellularization (2957.2 ± 340.8 N.mm -1 ) (predecellularization: 2685.4 ± 263.1 N.mm -1 ; n  = 5, 95% CL), but the difference was within natural tissue variation. Total DNA levels for all decellularized tissue regions of human IVDs (NP, iAF, oAF, EP, and VB) were below 50 ng.mg -1 dry tissue weight (range: 2 ng.mg -1 , iAF to 29 ng.mg -1 , VB) and the tissue retained high levels of GAGs. Further studies to assess the biocompatibility and regenerative potential of decellularized human IVDs in vitro and in vivo are now required; however, proof of technical feasibility has been demonstrated and the retention of bone in the IVD samples would allow incorporation of the tissue into the recipient spine. Impact statement Intervertebral disc (IVD) degeneration is a major cause of back pain. Current surgical treatments have limitations and relatively poor outcomes. An implantable cell-free biological scaffold, which will not invoke adverse immune responses, has the potential to preserve the natural mobility of the patient's spine and be regenerated with endogenous cells, preventing further degeneration and improving surgical outcomes. This study demonstrates, for the first time, that it is possible to create a cell-free human IVD biological scaffold with attached bone using decellularization technology, the first step toward the development of an implantable regenerative device for IVD replacement.

The successful development of cartilage repair treatments for the knee requires understanding of the biomechanical environment within the joint. Computational finite element models play an important role in non-invasively understanding knee mechanics, but it is important to compare model findings to experimental data. The purpose of this study was to develop a methodology for generating subject-specific finite element models of porcine tibiofemoral joints that was robust and valid over multiple different constraint scenarios. Computational model predictions of two knees were compared to experimental studies on corresponding specimens loaded under several different constraint scenarios using a custom designed experimental rig, with variations made to the femoral flexion angle and level of tibial freedom. For both in vitro specimens, changing the femoral flexion angle had a marked effect on the contact distribution observed experimentally. With the tibia fixed, the majority of the contact region shifted to the medial plateau as flexion was increased. This did not occur when the tibia was free to displace and rotate in response to applied load. These trends in contact distribution across the medial and lateral plateaus were replicated in the computational models. In an additional model with the meniscus removed, contact pressures were elevated by a similar magnitude to the increase seen when the meniscus was removed experimentally. Overall, the models were able to capture specimen-specific trends in contact distribution under a variety of different loads, providing the potential to investigate subject-specific outcomes for knee interventions., (Copyright © 2020 The Authors. Published by Elsevier Ltd.. All rights reserved.)

There is controversy over whether bone or cartilage is primarily involved in osteoarthritis (OA) pathogenesis; this is important for targeting early interventions. We explored evidence from animal models of knee OA by preforming a systematic review of PubMed, Scopus, and Web of Science for original articles reporting subchondral bone and cartilage pathology in animal models with epiphyseal closure. Extracted data included: method of induction; animal model; cartilage and bone assessment and method; meniscal assessment; skeletal maturity; controls; and time points assessed. Quality scoring was performed. The best evidence was synthesized from high-quality skeletally mature models, without direct trauma to tissues of interest and with multiple time points. Altogether, 2849 abstracts were reviewed. Forty-seven papers were included reporting eight different methods of inducing OA, six different species, six different methods of assessing cartilage, five different bone structural parameters, and four assessed meniscus as a potential initiator. Overall, the simultaneous onset of OA in cartilage and bone was reported in 82% of datasets, 16% reported bone onset, and 2% reported cartilage onset. No dataset containing meniscal data reported meniscal onset. However, using the best evidence synthesis (n = 8), five reported simultaneous onset when OA was induced, while three reported bone onset when OA occurred spontaneously; none reported cartilage onset. In summary, there is a paucity of well-designed studies in this area which makes the conclusions drawn conjectures rather than proven certainties. However, within the limitation of data quality, this review suggests that in animal models, the structural onset of knee OA occurs either in bone prior to cartilage pathology or simultaneously., (© 2020 The Authors. Journal of Orthopaedic Research® published by Wiley Periodicals, Inc. on behalf of Orthopaedic Research Society.)

Vertebroplasty has been widely used for the treatment of osteoporotic compression fractures but the efficacy of the technique has been questioned by the outcomes of randomized clinical trials. Finite-element (FE) models allow an investigation into the structural and geometric variation that affect the response to augmentation. However, current specimen-specific FE models are limited due to their poor reproduction of cement augmentation behavior. The aims of this study were to develop new methods of modeling the vertebral body in both a nonaugmented and augmented state. Experimental tests were conducted using human lumbar spine vertebral specimens. These tests included micro-computed tomography imaging, mechanical testing, augmentation with cement, reimaging, and retesting. Specimen-specific FE models of the vertebrae were made comparing different approaches to capturing the bone material properties and to modeling the cement augmentation region. These methods significantly improved the modeling accuracy of nonaugmented vertebrae. Methods that used the registration of multiple images (pre- and post-augmentation) of a vertebra achieved good agreement between augmented models and their experimental counterparts in terms of predictions of stiffness. Such models allow for further investigation into how vertebral variation influences the mechanical outcomes of vertebroplasty., Competing Interests: The authors declare no potential conflict of interest., (© 2020 The Authors. JOR Spine published by Wiley Periodicals, Inc. on behalf of Orthopaedic Research Society.)

The knee joint is a complex mechanical system, and computational modelling can provide vital information for the prediction of disease progression and of the potential for therapeutic interventions. This review provides an overview of the challenges involved in developing finite element models of the tibiofemoral joint, including the representation of appropriate geometry and material properties, loads and motions, and establishing pertinent outputs. The importance of validation for computational models in biomechanics has been highlighted by a number of papers, and finite element models of the tibiofemoral joint are a particular area in which validation can be challenging, due to the complex nature of the knee joint, its geometry and its constituent tissue properties. A variety of study designs have emerged to tackle these challenges, and these can be categorised into several different types. The role of validation, and the strategies adopted by these different study types, are discussed. Models representing trends and sensitivities often utilise generic representations of the knee and provide conclusions with relevance to general populations, usually without explicit validation. Models representing in vitro specimens or in vivo subjects can, to varying extents, be more explicitly validated, and their conclusions are more subject-specific. The potential for these approaches to examine the effects of patient variation is explored, which could lead to future applications in defining how treatments may be stratified for subgroups of patients., (Copyright © 2019 The Authors. Published by Elsevier Ltd.. All rights reserved.)

Study Design: An in vitro magnetic resonance imaging (MRI) study., Objective: Investigate the potential of high-field MRI for producing higher quality images of the intervertebral disc (IVD) to better distinguish structural details., Summary of Background Data: Higher spatial and contrast resolution are important advantages when imaging the complex tissue structures in the spine such as the IVDs. However, at present it is challenging to capture the substructural details in the IVD such as the lamellae., Methods: Three MRI sequences; two-dimensional proton-density-weighted Turbo-Spin-Echo (PD-TSE), 2D T2-weighted Turbo-Spin-Echo (T2W-TSE) with fat-saturation (FS), and 3D Spoiled-Gradient-Echo (3D-GE), were modified based on the image quality and scan duration. IVDs of three intact cadaveric lumbar-spines (T12-S1, Age 83-94 yr) were imaged using these optimized sequences. Thereafter each IVD was transversely sectioned and the exposed surfaces were photographed. Landmark observations from corresponding MRI slices and photographs were compared to confirm the MRI captured morphology. The image quality was evaluated using signal-to-noise ratio (SNR), and relative-contrast values. Finally, the underlying tissue structures, including specific pathological features, were qualitatively compared between the MR images and photographs., Results: Observations from photographs and corresponding MRI slices matched well. The PD-TSE sequence had better overall SNR, but the relative contrast between the tissue types was relatively poor. The 3D-GE sequence had higher relative contrast between the IVD and bone, but not between annulus and nucleus regions. The T2W images provided the best relative contrast between the annulus and nucleus, however the standard deviations here were high. Structural details including fissures, vascular and granular tissue proliferation, and pathologies in the endplate region, were identifiable from the MR images obtained using the optimized sequences., Conclusion: The results demonstrate the potential of high-field MRI to capture the IVD structural details. Since the acquisition durations were within clinically acceptable levels, these methodological improvements have the potential to enhance clinical diagnostics., Level of Evidence: 4.

Long bone fractures are common and although treatments are highly effective in most cases, it is challenging to achieve successful repair for groups such as open and periprosthetic fractures. Previous biomechanical studies of fracture repair, including computer and experimental models, have simplified the fracture with a flat geometry or a gap, and there is a need for a more accurate fracture representation to mimic the situation in-vivo . The aims of this study were to develop a methodology for generating repeatable transverse fractures in long bones in-vitro and to characterise the fracture surface using non-invasive computer tomography (CT) methods. Ten porcine femora were fractured in a custom-built rig under high-rate loading conditions to generate consistent transverse fractures (angle to femoral axis < 30 degrees). The bones were imaged using high resolution peripheral quantitative CT (HR-pQCT). A method was developed to extract the roughness and form profiles of the fracture surface from the image data using custom code and Guassian filters. The method was tested and validated using artificially generated waveforms. The results revealed that the smoothing algorithm used in the script was robust but the optimum kernel size has to be considered.

Intervertebral disc degeneration is one of the leading causes of back pain, but treatment options remain limited. Recently, there have been advances in the development of biomaterials for nucleus augmentation; however, the testing of such materials preclinically has proved challenging. The aim of this study was to develop methods for fabricating and testing bone-disc-bone specimens in vitro for examining the performance of nucleus augmentation procedures. Control, nucleotomy and treated intervertebral disc specimens were fabricated and tested under static load. The nucleus was removed from nucleotomy specimens using a trans-endplate approach with a bone plug used to restore bony integrity. Specimen-specific finite element models were developed to elucidate the reasons for the variations observed between control specimens. Although the computational models predicted a statistically significant difference between the healthy and nucleotomy groups, the differences found experimentally were not significantly different. This is likely due to variations in the material properties, hydration and level of annular collapse. The deformation of the bone was also found to be non-negligible. The study provides a framework for the development of testing protocols for nucleus augmentation materials and highlights the need to control disc hydration and the length of bone retained to reduce inter-specimen variability.

Image-based continuum-level finite element models have been used for bones to evaluate fracture risk and the biomechanical effects of diseases and therapies, capturing both the geometry and tissue mechanical properties. Although models of vertebrae of various species have been developed, an inter-species comparison has not yet been investigated. The purpose of this study was to derive species-specific modelling methods and compare the accuracy of image-based finite element models of vertebrae across species. Vertebral specimens were harvested from porcine (N = 12), ovine (N = 13) and bovine (N = 14) spines. The specimens were experimentally loaded to failure and apparent stiffness values were derived. Image-based finite element models were generated reproducing the experimental protocol. A linear relationship between the element grayscale and elastic modulus was calibrated for each species matching in vitro and in silico stiffness values, and validated on independent sets of models. The accuracy of these relationships were compared across species. Experimental stiffness values were significantly different across species and specimen-specific models required species-specific linear relationship between image grayscale and elastic modulus. A good agreement between in vitro and in silico values was achieved for all species, reinforcing the generality of the developed methodology.

The development of current surgical treatments for intervertebral disc damage could benefit from virtual environment accounting for population variations. For such models to be reliable, a relevant description of the mechanical properties of the different tissues and their role in the functional mechanics of the disc is of major importance. The aims of this work were first to assess the physiological hoop strain in the annulus fibrosus in fresh conditions ( n  = 5) in order to extract a functional behaviour of the extrafibrillar matrix; then to reverse-engineer the annulus fibrosus fibrillar behaviour ( n  = 6). This was achieved by performing both direct and global controlled calibration of material parameters, accounting for the whole process of experimental design and in silico model methodology. Direct-controlled models are specimen-specific models representing controlled experimental conditions that can be replicated and directly comparing measurements. Validation was performed on another six specimens and a sensitivity study was performed. Hoop strains were measured as 17 ± 3% after 10 min relaxation and 21 ± 4% after 20-25 min relaxation, with no significant difference between the two measurements. The extrafibrillar matrix functional moduli were measured as 1.5 ± 0.7 MPa. Fibre-related material parameters showed large variability, with a variance above 0.28. Direct-controlled calibration and validation provides confidence that the model development methodology can capture the measurable variation within the population of tested specimens., Competing Interests: The authors have no competing interests.

The aims of this study were to assess the damage and failure strengths of lamellar fibrous tissues, such as the anterior annulus fibrosus (AF), and to develop a mathematical model of damage propagation of the lamellae and inter-lamellar connections. This level of modelling is needed to accurately predict the effect of damage and failure induced by trauma or clinical interventions. 26 ovine anterior AF cuboid specimens from 11 lumbar intervertebral discs were tested in radial tension and mechanical parameters defining damage and failure were extracted from the in-vitro data. Equivalent 1D analytical models were developed to represent the specimen strength and the damage propagation, accounting for the specimen dimensions and number of lamellae. Model parameters were calibrated on the in-vitro data. Similar to stiffness values reported for other orientations, the outer annulus was found stronger than the inner annulus in the radial direction, with failure at higher stress values. The inner annulus failed more progressively, showing macroscopic failure at a higher strain value. The 1D analytical model of damage showed that lamellar damage is predominant in the failure mechanism of the AF. The analytical model of the connections between lamellae allowed us to represent separately damage processes in the lamellae and the inter-lamellar connections, which cannot be experimentally tested individually., (Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.)

The aim of this study was to develop a finite element (FE) hip model with subject-specific geometry and biphasic cartilage properties. Different levels of detail in the representation of fibre reinforcement were considered to evaluate the feasibility to simplify the complex depth-dependent fibre pattern in the native hip joint. A FE model of a cadaveric hip with subject-specific geometry was constructed through micro-computed-tomography (µCT) imaging. The cartilage was assumed to be biphasic and fibre-reinforced with different levels of detail in the fibre representation. Simulations were performed for heel-strike, mid-stance and toe-off during walking and one-leg-stance over 1500s. It was found that the required level of detail in fibre representation depends on the parameter of interest. The contact stress of the native hip joint could be realistically predicted by simplifying the fibre representation to being orthogonally reinforced across the whole thickness. To predict the fluid pressure, depth-dependent fibre organisation is needed but specific split-line pattern on the surface of cartilage is not necessary. Both depth-dependent and specific surface fibre orientations are required to simulate the strains., (Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.)

Degeneration of the spinal discs is a major cause of back pain. During the degeneration process, there is a loss of glycosaminoglycans (GAGs) from the proteoglycan-rich gel in the disc's nucleus, which adversely alters biomechanical performance. Current surgical treatments for back pain are highly invasive and have low success rates; there is an urgent need for minimally-invasive approaches that restore the physiological mechanics of the spine. Here we present an injectable peptide:GAG hydrogel that rapidly self-assembles in situ and restores the mechanics of denucleated intervertebral discs. It forms a gel with comparable mechanical properties to the native tissue within seconds to minutes depending on the peptide chosen. Unlike other biomaterials that have been proposed for this purpose, these hybrid hydrogels can be injected through a very narrow 25 G gauge needle, minimising damage to the surrounding soft tissue, and they mimic the ability of the natural tissue to draw in water by incorporating GAGs. Furthermore, the GAGs enhance the gelation kinetics and thermodynamic stability of peptide hydrogels, significantly reducing effusion of injected material from the intervertebral disc (GAG leakage of 8 ± 3% after 24 h when peptide present, compared to 39 ± 3% when no peptide present). In an ex vivo model, we demonstrate that the hydrogels can restore the compressive stiffness of denucleated bovine intervertebral discs. Compellingly, this novel biomaterial has the potential to transform the clinical treatment of back pain by resolving current surgical challenges, thus improving patient quality of life.

The complex motion and geometry of the spine in the cervical region makes it difficult to determine how loads are distributed through adjacent vertebrae or between the zygapophysial (facet) joints and the intervertebral disc. Validated finite element modes can give insight on this distribution. The aim of this contribution was to produce direct validation of subject-specific finite element models of Functional Spinal Units (FSU׳s) of the cervical spine and to evaluate the importance of including fibre directionality in the mechanical description of the annulus fibrosus. Eight specimens of cervical FSU׳s were prepared from five ovine spines and mechanically tested in axial compression monitoring overall load and displacements as well as local facet joints pressure and displacement. Subject-specific finite element models were produced from microCT image data reproducing the experimental setup and measuring global axial force and displacement as well as local facet joints displacement and contact forces. Material models and parameters were taken from the literature, testing isotropic and anisotropic materials for the annulus fibrosus. The validated models showed that adding the direction of the fibres to their non-linear behaviour in the description of the annulus fibrosus improves the predictions at large strain values but not at low strain values. The load transferred through the facet joints was always accurate, irrespective of the annulus material model, while the predicted facet displacement was larger than the measured one but not significantly. This is, to the authors׳ knowledge, the first subject-specific direct validation study on a group of specimens, accounting for inter-subject variability., (Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.)

Study Design: An in vitro study of the intervertebral disc (IVD) structure using 9.4T magnetic resonance imaging (MRI)., Objective: Investigate the potential of ultrahigh-field strength MRI for higher quality 3-dimensional (3D) volumetric MRI datasets of the IVD to better distinguish structural details., Summary of Background Data: MRI has the advantages of being nondestructive and 3D in comparison to most techniques used to obtain the structural details of biological tissues, however, its poor image quality at higher resolution is a limiting factor. Ultrahigh-field MRI could improve the imaging of biological tissues but the current understanding of its application for spinal tissue is limited., Methods: 2 ovine spinal segments (C7-T1, T2-T3) containing the IVD were separately imaged using 2 sequences; 3D spin echo (multislice-multiecho) pulse sequence for the C7-T1 sample and 3D gradient echo (fast-low-angle-shot) pulse sequence for the T2-T3 sample. The C7-T1 sample was subsequently decalcified and imaged again using the same scanning parameters. Histological sections obtained from the decalcified sample were stained followed by digital scanning. Observations from corresponding MRI slices and histological sections were compared as a method of confirmation of morphology captured under MRI. The signal-to-noise ratio (SNR), contrast-to-noise ratio (CNR) and relative-contrast values were calculated for quantitative evaluation of image quality., Results: Measurements from histology sections and corresponding MRI slices matched well. Both sequences revealed finer details of the IVD structure. Under the spin echo sequence, the annulus lamellae architecture was distinguishable and the SNR and CNR values were higher. The relative contrast was considerably higher between high (nucleus) and low (bone) signal constituents, but between the nucleus and the annulus the relative contrast was low. Under the gradient echo sequence, although the relative contrasts between constituents were poor, the fiber orientation was clearly manifested., Conclusion: The obtained positive results demonstrate the potential of ultrahigh-field strength MRI to nondestructively capture the IVD structure., Level of Evidence: N/A.

Background: The incidence of periprosthetic femoral fractures (PFF) around a stable stem is increasing. The aim of this biomechanical study was to examine how three different methods of fixation, for Vancouver type B1 PFF, alter the stiffness and strain of a construct under various configurations, in order to gain a better insight into the optimal fixation method., Methods: Three different combinations of proximal screws and Dall-Miles cables were used: (A) proximal unicortical locking screws alone; (B) proximal cables and unicortical locking screws; (C) proximal cable alone, each in combination with distal bicortical locking screws, to fix a stainless steel locking compression plate to five synthetic femora with simulated Vancouver type B1 PFFs. In one synthetic femora, there was a 10-mm fracture gap, in order to simulate a comminuted injury. The other four femora had no fracture gap, to simulate a stable injury. An axial load was applied to the constructs at varying degrees of adduction, and the overall construct stiffness and surface strain were measured., Results: With regards to stiffness, in both the gap and no gap models, method of fixation A was the stiffest form of fixation. The inclusion of the fracture gap reduced the stiffness of the construct quite considerably for all methods of fixation. The strain across both the femur and the plate was considerably less for method of fixation C, compared to A and B, at the locations considered in this study., Conclusion: This study highlights that the inclusion of cables appears to damage the screw fixations and does not aid in construct stability. Furthermore, the degree of fracture reduction affects the whole construct stability and the bending behaviour of the fixation.

Parameterised finite element models of the human hip have the potential to allow controlled analysis of the effect of individual geometric features on the contact mechanics of the joint. However, the challenge lies in defining a set of parameters which sufficiently capture the joint geometry in order to distinguish between individuals. In this study, a simple set of parameters to describe the geometries of acetabulum and cartilage in the hip were extracted from two segmentation-based models, which were then used to generate the parameterised finite element models for the two subjects. The contact pressure and contact area at the articular surface predicted from the parameterised finite element models were compared with the results from the segmentation-based models. The differences in the predicted results between the parameterised models and segmentation-based models were found to be within 11% across seven activities simulated. In addition, the parameterised models were able to replicate features of the contact pressure/area fluctuations over the loading cycle that differed between the two subjects. These results provide confidence that the parameterised approach could be used to generate representative finite element models of the human hip for contact analysis. Such a method has the potential to be used to systematically evaluate geometric features that can be captured from simple clinical measurements and provide a cost- and time-effective approach for stratification of the acetabular geometries in the patient population., (© IMechE 2015.)

The inter-lamellar connectivity of the annulus fibrosus in the intervertebral disc has been shown to affect the prediction of the overall disc behaviour in computational models. Using a combined experimental and computational approach, the inter-lamellar mechanical behaviour of the disc annulus was investigated under conditions of radial loading. Twenty-seven specimens of anterior annulus fibrosus were dissected from 12 discs taken from four frozen ovine thoracolumbar spines. Specimens were grouped depending on their radial provenance within the annulus fibrosus. Standard tensile tests were performed. In addition, micro-tensile tests under microscopy were used to observe the displacement of the lamellae and inter-lamellar connections. Finite elements models matching the experimental protocols were developed with specimen-specific geometries and boundary conditions assuming a known lamellar behaviour. An optimisation process was used to derive the interface stiffness values for each group. The assumption of a linear cohesive interface was used to model the behaviour of the inter-lamellar connectivity. The interface stiffness values derived from the optimisation process were consistently higher than the corresponding lamellar values. The interface stiffness values of the outer annulus were from 43% to 75% higher than those of the inner annulus. Tangential stiffness values for the interface were from 6% to 39% higher than normal stiffness values within each group and similar to values reported by other investigators. These results reflect the intricate fibrous nature of the inter-lamellar connectivity and provide values for the representation of the inter-lamellar behaviour at a continuum level., (Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.)

Hip hemiarthroplasty is a common treatment for femoral neck fracture. However, the acetabular cartilage may degenerate after hemiarthroplasty leading to postoperative failure and the need for revision surgery. The clearance between the acetabular cartilage and head of the prosthesis is one of the potential reasons for this failure. In this study, the influence of joint clearance on the biomechanical function of a generic hip model in hemiarthroplasty was investigated using biphasic numerical simulation. Both a prolonged loading period of 4000 s and dynamic gait load of 10 cycles were considered. It was found that a larger clearance led to a higher stress level, a faster reduction in load supported by the fluid and a faster cartilage consolidation process. Additionally, the mechanical performance of the acetabular cartilage in the natural model was similar to that in the hemiarthroplasty model with no clearance but different from the hemiarthroplasty models with clearances of 0.5mm and larger. The results demonstrated that a larger clearance in hip hemiarthroplasty is more harmful to the acetabular cartilage and prosthesis heads with more available dimensions (i.e. smaller increments in diameter) could be manufactured for surgeons to achieve a lower clearance, and reduced contact stress in hemiarthroplasty surgeries., (Copyright © 2014 The Authors. Published by Elsevier Ltd.. All rights reserved.)

Finite element models are becoming increasingly useful tools to conduct parametric analysis, design optimisation and pre-clinical testing for hip joint replacements. However, the verification of the finite element model is critically important. The purposes of this study were to develop a three-dimensional anatomic finite element model for a modular metal-on-polyethylene total hip replacement for predicting its contact mechanics and to conduct experimental validation for a simple finite element model which was simplified from the anatomic finite element model. An anatomic modular metal-on-polyethylene total hip replacement model (anatomic model) was first developed and then simplified with reasonable accuracy to a simple modular total hip replacement model (simplified model) for validation. The contact areas on the articulating surface of three polyethylene liners of modular metal-on-polyethylene total hip replacement bearings with different clearances were measured experimentally in the Leeds ProSim hip joint simulator under a series of loading conditions and different cup inclination angles. The contact areas predicted from the simplified model were then compared with that measured experimentally under the same conditions. The results showed that the simplification made for the anatomic model did not change the predictions of contact mechanics of the modular metal-on-polyethylene total hip replacement substantially (less than 12% for contact stresses and contact areas). Good agreements of contact areas between the finite element predictions from the simplified model and experimental measurements were obtained, with maximum difference of 14% across all conditions considered. This indicated that the simplification and assumptions made in the anatomic model were reasonable and the finite element predictions from the simplified model were valid., (© IMechE 2014.)

The aim of this study was to determine the cartilage contact mechanics and the associated fluid pressurisation of the hip joint under eight daily activities, using a three-dimensional finite element hip model with biphasic cartilage layers and generic geometries. Loads with spatial and temporal variations were applied over time and the time-dependent performance of the hip cartilage during walking was also evaluated. It was found that the fluid support ratio was over 90% during the majority of the cycles for all the eight activities. A reduced fluid support ratio was observed for the time at which the contact region slid towards the interior edge of the acetabular cartilage, but these occurred when the absolute level of the peak contact stress was minimal. Over 10 cycles of gait, the peak contact stress and peak fluid pressure remained constant, but a faster process of fluid exudation was observed for the interior edge region of the acetabular cartilage. The results demonstrate the excellent function of the hip cartilage within which the solid matrix is prevented from high levels of stress during activities owing to the load shared by fluid pressurisation. The findings are important in gaining a better understanding of the hip function during daily activities, as well as the pathology of hip degeneration and potential for future interventions. They provide a basis for future subject-specific biphasic investigations of hip performance during activities., (© IMechE 2014.)

Hip models that incorporate the biphasic behaviour of articular cartilage can improve understanding of the joint function, pathology of joint degeneration and effect of potential interventions. The aim of this study was to develop a specimen-specific biphasic finite element model of a porcine acetabulum incorporating a biphasic representation of the articular cartilage and to validate the model predictions against direct experimental measurements of the contact area in the same specimen. Additionally, the effect of using a different tension-compression behaviour for the solid phase of the articular cartilage was investigated. The model represented different radial clearances and load magnitudes. The comparison of the finite element predictions and the experimental measurement showed good agreement in the location, size and shape of the contact area, and a similar trend in the relationship between contact area and load was observed. There was, however, a deviation of over 30% in the magnitude of the contact area, which might be due to experimental limitations or to simplifications in the material constitutive relationships used. In comparison with the isotropic solid phase model, the tension-compression solid phase model had better agreement with the experimental observations. The findings provide some confidence that the new biphasic methodology for modelling the cartilage is able to predict the contact mechanics of the hip joint. The validation provides a foundation for future subject-specific studies of the human hip using a biphasic cartilage model., (© IMechE 2014.)

Significant advances in the functional analysis of musculoskeletal systems require the development of modelling techniques with improved focus, accuracy and validity. This need is particularly visible in the fields, such as palaeontology, where unobservable parameters may lie at the heart of the most interesting research questions, and where models and simulations may provide some of the most innovative solutions. Here, we report on the development of a computational modelling method to generate estimates of the mechanical properties of vertebral bone across two living species, using elderly human and juvenile porcine specimens as cases with very different levels of bone volume fraction and mineralization. This study is presented in two parts; part I presents the computational model development and validation, and part II the virtual loading regime and results. This work paves the way for the future estimation of mechanical properties in fossil mammalian bone.