Search

Cemented carbide tools are extensively used in the zipper industry, including shearing of a pre-formed Cu15Zn wire into individual zipper elements. Although the work material is significantly softer than the tool, wear is the life limiting factor for the tools and is considered to be of tribochemical nature. So far it has not been explained, however, it is known that the wear rate of uncoated, as well as CrC and CrN coated, cemented carbide increases dramatically when Zn is omitted from the Cu alloy. In this paper, worn tool surfaces, including any transferred material, were studied to investigate the tribochemical wear mechanism in detail. Material transfer occurred onto all tool surfaces. Cu and Zn were separated on the sub-micron scale, and preferential transfer of one of the constituents was observed. This is reflected in the outermost surface of the sheared element, which shows a homogeneous composition elsewhere. Oxidation was observed of all tool surfaces, which indicates elements of oxidative wear. Further, any Zn transferred to the tool surfaces was oxidized. Thus, it is suggested that the presence of Zn reduces the oxygen available and consequently reduces the oxidation rate of the tool surfaces, leading to the protective effect previously observed.

Cemented carbide tools are commonly used in both shearing and forging processes associated to zipper production. In the actual production, the tool life is often limited by wear after many millions of repeated contacts with copper alloys. A series of previous investigations has shown that the wear of the tools is tribochemical for both shearing and forging, however with different features. The mechanisms causing this wear are not well understood. To gain deeper insights into the active wear mechanisms during the copper alloy forging process, a new tribotester was proposed and developed. By this tester, a cemented carbide cylinder is repeatedly put in sliding contact with a rotating copper alloy cylinder in a crossed cylinders arrangement. The test was interrupted at selected intervals so that the cemented carbide cylinder could be repeatedly evaluated by SEM and EDS. It was revealed that the characteristic wear of actual tools, tribochemical smooth wear in common, and preferential removal of Co binder and partially Zn rich transfer for the forging tool, can be reproduced by this tribotester.

Additive manufacturing (AM) using powder bed fusion is becoming a mature technology that offers great possibilities and design freedom for manufacturing of near net shape components. However, for many gas turbine and aerospace applications, machining is still required, which motivates further research on the machinability and work piece integrity of additive-manufactured superalloys. In this work, turning tests have been performed on components made with both Powder Bed Fusion for Laser Beam (PBF-LB) and Electron Beam (PBF-EB) in as-built and heat-treated conditions. The two AM processes and the respective heat-treatments have generated different microstructural features that have a great impact on both the tool wear and the work piece surface integrity. The results show that the PBF-EB components have relatively lower geometrical accuracy, a rough surface topography, a coarse microstructure with hard precipitates and low residual stresses after printing. Turning of the PBF-EB material results in high cutting tool wear, which induces moderate tensile surface stresses that are balanced by deep compressive stresses and a superficial deformed surface that is greater for the heat-treated material. In comparison, the PBF-LB components have a higher geometrical accuracy, a relatively smooth topography and a fine microstructure, but with high tensile stresses after printing. Machining of PBF-LB material resulted in higher tool wear for the heat-treated material, increase of 49%, and significantly higher tensile surface stresses followed by shallower compressive stresses below the surface compared to the PBF-EB materials, but with no superficially deformed surface. It is further observed an 87% higher tool wear for PBF-EB in as-built condition and 43% in the heat-treated condition compared to the PBF-LB material. These results show that the selection of cutting tools and cutting settings are critical, which requires the development of suitable machining parameters that are, QC 20240122

BACKGROUND: Swimming is a genotype-specific trigger in long QT syndrome type 1 (LQT1). OBJECTIVE: To examine the autonomic response to water activities in children and adolescents with LQT1. METHODS: In this cross-sectional study, LQT1 patients were age and sex matched to one healthy control subject. Electrocardiograms (ECGs) were recorded during face immersion (FI), swimming, diving, and whole-body submersion (WBS). Heart rate (HR) and heart rate variability (HRV) was measured. The high frequency (HF) component of HRV was interpreted to reflect parasympathetic activity, while the low frequency (LF) component was interpreted as reflecting the combined influence of sympathetic and parasympathetic activity on autonomic nervous modulation of the heart. RESULTS: Fifteen LQT1 patients (aged 7-19 years, all on beta-blocker therapy) and fifteen age and sex matched non-medicated controls were included. No significant ventricular arrhythmias were observed in the LQT1 population during the water activities. Out of these 15 matched pairs, 12 pairs managed to complete FI and WBS for more than 10 seconds and were subsequently included in HR and HRV analyses. In response to FI, the LQT1 group experienced a drop in HR of 48 bpm, compared to 67 bpm in the control group (p = 0.006). In response to WBS, HR decreased by 48 bpm in the LQT1 group and 70 bpm in the control group (p = 0.007). A significantly lower PTOT (p < 0.001) and HF (p = 0.011) component was observed before, during and after FI in LQT1 patients compared with the controls. Before, during and after WBS, a significantly lower total power (p < 0.001), LF (p = 0.002) and HF (p = 0.006) component was observed in the LQT1 patients. CONCLUSION: A significantly lower HR decrease in response to water activities was observed in LQT1 subjects on beta-blocker therapy, compared to matched non-medicated controls. The data suggests an impaired parasympathetic response in LQT1 children and adolescents. An aberrant autonomic ner

BACKGROUND: Cerebral blood flow (CBF) is believed to be relatively constant within an upper and lower blood pressure limit. Different methods are available to monitor CBF autoregulation during surgery. This study aims to critically analyze the application of the cerebral oxygenation index (COx), one of the commonly used techniques, using a reference to data from a series of clinical registrations. METHOD: CBF was monitored using near-infrared spectroscopy, while cerebral blood pressure was estimated by recordings obtained from either the radial or femoral artery in 10 patients undergoing cardiopulmonary bypass. The association between CBF and blood pressure was calculated as a moving continuous correlation coefficient. A COx index > 0.4 was regarded as a sign of abnormal cerebral autoregulation (CA). Recordings were examined to discuss reliability measures and clinical feasibility of the measurements, followed by interpretation of individual results, identification of possible pitfalls, and suggestions of alternative methods. RESULTS AND CONCLUSION: Monitoring of CA during cardiopulmonary bypass is intriguing and complex. A series of challenges and limitations should be considered before introducing this method into clinical practice.

In the present study, crack propagation through the case hardened region of two different PM steels manufactured with different powder size distributions and sintered at different temperatures has been investigated. EBSD was used to study the microstructure before and after case hardening, revealing the relationship between powder particle grains after sintering and prior austenite grains after case hardening. A novel approach was used to achieve short cracks (10–20 µm) with high repeatability. The cracks were then analysed using EBSD and SEM, revealing detailed and novel information about the crack propagation route in the materials. Both tested materials show the same crack propagation behaviour. If a prior grain/prior austenite boundary is present within an angle from the crack initiation site, the cracks will follow the boundary and thus propagate intergranular, suggesting that the preferred route of crack propagation in case hardened sintered steel is along these boundaries.

Powder based metal additive manufacturing processes like Powder Bed Fusion – Laser Beam utilize gasatomized metal powders as feedstock material. Typically, for nickel-based alloys such as Alloy 625, argongas is used during the atomization process. Considering the larger environmental impact of argon gascompared to nitrogen gas, and the increasing use of gas atomized metal powders, the environmentalimpact of powder based additive manufacturing techniques could be mitigated if gas atomization ofalloys such as Alloy 625 using nitrogen was possible. This work investigates the feasibility of tailoringan alloy to allow atomization using nitrogen gas while remaining within the Alloy 625 specification.This is achieved by limiting the nitrogen pick-up during the atomization process, primarily by reducingthe titanium content. The metallurgical implications of this tailored alloy and the subsequent atomizationusing nitrogen, as well as the attained microstructure from the Powder Bed Fusion – Laser Beam processis investigated and compared to a more common 625 alloy composition which was atomized usingargon. Furthermore, the microstructural development of the alloys after heat treatments are evaluated.Lastly corrosive properties, as well as tensile and impact properties are evaluated both in the as-builtand hot isostatic pressed condition.

In the present study, crack propagation through the case hardened region of two different PM steels manufactured with different powder size distributions and sintered at different temperatures has been investigated. EBSD was used to study the microstructure before and after case hardening, revealing the relationship between powder particle grains after sintering and prior austenite grains after case hardening. A novel approach was used to achieve short cracks (10–20 µm) with high repeatability. The cracks were then analysed using EBSD and SEM, revealing detailed and novel information about the crack propagation route in the materials. Both tested materials show the same crack propagation behaviour. If a prior grain/prior austenite boundary is present within an angle from the crack initiation site, the cracks will follow the boundary and thus propagate intergranular, suggesting that the preferred route of crack propagation in case hardened sintered steel is along these boundaries.

The use of implantable cardioverter defibrillators (ICDs) in long QT syndrome (LQTS) patients is essential in high-risk patients. However, it is sometimes used in patients without high-risk profiles for whom the expected benefit may be lower than the risk of ICD harm. Here, we evaluated ICD benefit and harm by assessing risk according to risk scores and pre-ICD clinical characteristics. Design. We studied 109 Swedish LQTS patients drawn from the Swedish ICD and Pacemaker Registry with data collected from medical records. In addition to clinical characteristics, we used two risk scores to assess pre-ICD risk, and evaluated ICD benefit and harm. Results. Twenty percent of all patients received ≥1 appropriate shock with a first appropriate shock incidence rate of 4.3 per 100 person-years. A long QTc (≥550 ms) and double mutations were significantly associated with appropriate shock. Low risk scores among patients without pre-ICD aborted cardiac arrest were not significantly associated with low risk of first appropriate shock. The incidence rates of a first inappropriate shock and first complication were 3.0 and 7.6 per 100 person-years, respectively. Conclusion. Our findings on ICD harm emphasize the importance of careful individual pre-ICD consideration. When we applied two risk scores to patients without pre-ICD aborted cardiac arrest, we could not validate their ability to identify patients with low risk of appropriate shocks and patients who were assessed as having a low risk still received appropriate shocks. This further supports the complexity of risk stratification and the difficulty of using risk scores.

Cemented carbide tools are commonly used in both cutting and forging processes associated to zipper produc-tion. In production, the tools experience many millions of repeated contacts, hence they must be very durable to keep the wear at acceptable levels. Although the zipper elements in this investigation are made in a relatively soft CuZn alloy, the wear becomes significant and the tool life a production limiting factor. The wear process is to a large extent unknown. To increase the understanding, forging dies used for an increasing number of forgings in actual production, have been studied in detail. Initially the Co binder is preferentially worn off, and transferred CuZn partly fills the cavities. Interestingly, the repeating forging contacts lead to modification of the composition of the transferred material, which partly separates into Cu rich and Zn rich parts, where the Zn rich parts show a high presence of oxygen. During the life span of the tool, represented by the controlled use of forging tools to different percentages of their estimated life, the WC grains are gradually worn into faceted shapes. The most severely worn region of the forging dies develops an increasing surface roughness, which act to shape a corre-sponding pattern on the zipper elements.

Introduction/aim: Young patients with Fontan circulation may have low serum 25-hydroxyvitamin D levels, an affected liver, and unhealthy body compositions. This study aimed to explore the association between vitamin D intake/levels, liver biomarkers, and body composition in young Fontan patients. Method: We collected prospective data in 2017 to 2018, obtained with food-frequency questionnaires, biochemical analyses of liver biomarkers, and dual-energy X-ray absorptiometry scans in 44 children with Fontan circulation. Body compositions were compared to matched controls (n = 38). Linear regression analyses were used to investigate associations of biomarkers, leg pain, and lean mass on serum levels of 25-hydroxyvitamin D. Biomarkers were converted to z scores and differences were evaluated within the Fontan patients. Results: Our Fontan patients had a daily mean vitamin D intake of 9.9 µg and a mean serum 25-hydroxyvitamin D of 56 nmol/L. These factors were not associated with fat or lean mass, leg pain, or biomarkers of liver status. The Fontan patients had significantly less lean mass, but higher fat mass than controls. Male adolescents with Fontan circulation had a greater mean abdominal fat mass than male controls and higher cholesterol levels than females with Fontan circulation. Conclusion: Vitamin D intake and serum levels were not associated with body composition or liver biomarkers in the Fontan group, but the Fontan group had lower lean mass and higher fat mass than controls. The more pronounced abdominal fat mass in male adolescents with Fontan circulation might increase metabolic risks later in life., Originally included in thesis in manuscript form.