Search

Obesity has become a global problem that poses a serious threat to human health. Laparoscopic sleeve gastrectomy (LSG) is an effective long-term treatment. However, the weight loss of some patients after LSG is still insufficient. It is necessary to investigate the factors associated with inadequate weight loss after LSG.The objective of this study was to explore whether preoperative insulin secretion could be associated with weight loss after LSG in patients with obesity.This is a single-center prospective cohort study conducted in a university hospital.Patients from a prospective database who underwent LSG were analyzed. All 178 participants underwent a 75-g oral glucose tolerance test (OGTT) to assess preoperative insulin and c-peptide secretion before LSG. The areas under the curve (AUCs) for glucose, insulin, and c-peptide were determined in the OGTT. The percentage of excess weight loss (%EWL) and the percentage of total weight loss (%TWL) were used to estimate the effect of weight loss after LSG. Regression models were used to assess the correlation between preoperative insulin and c-peptide secretion with %EWL ≥75% and TWL ≥35% at 12 months after LSG.The AUCs of insulin and c-peptide were significantly lower in the %EWL ≥75% and %TWL ≥35% groups at 0-30 minutes, 0-60 minutes, and 0-120 minutes during the OGTT. At 30, 60, and 120 minutes during the OGTT, c-peptide levels were significantly lower in the %EWL ≥75% group and %TWL ≥35% group. The preoperative c-peptide level at 30 minutes during the OGTT (Csub30/sub) was significantly negatively correlated with %EWL (β = -.37, Plt; .001) and %TWL (β = -.28, P = .011). Univariate logistic regression analysis showed that preoperative Csub30/subwas associated with %EWL ≥75% and %TWL ≥35% after LSG. According to multiple logistic regression analysis, patients with a low preoperative Csub30/subhad an 8-fold higher %TWL ≥35% after LSG than those with a high Csub30/sub(odds ratio: 8.41 [95% confidence interval: 1.46-48.58], P = .017). Similarly, patients with a low preoperative Csub30/subhad a 7-fold higher EWL% ≥75% after LSG than patients with a high Csub30/sub(odds ratio: 7.25 [95% confidence interval: 1.11-47.50], P = .039).The rate of weight loss after LSG is low among patients with preoperative hyperinsulinemia. The preoperative c-peptide level at 30 minutes during the OGTT is associated with weight loss after LSG.

Liangjing Lv,1,&ast; Yangmei Zhou,1,&ast; Xiangjun Chen,1 Lilin Gong,1 Jinshan Wu,1 Wenjin Luo,1 Yan Shen,1 Shichao Han,2 Jinbo Hu,1 Yue Wang,1 Qifu Li,1 Zhihong Wang1 On behalf of the Chongqing Diabetes Registry Group1Department of Endocrinology, The First Affiliated Hospital of Chongqing Medical University, Chongqing, People’s Republic of China; 2Department of Statistics, University of California, Berkeley, CA, USA&ast;These authors contributed equally to this workCorrespondence: Zhihong WangDepartment of Endocrinology, The First Affiliated Hospital of Chongqing Medical University, Yuzhong District, Chongqing, People’s Republic of ChinaTel/Fax +86-023-89011552Email towzh713@126.comBackground: Diabetic kidney disease (DKD) lacks a simple and relatively accurate predictor. The Triglyceride–Glucose (TyG) Index is a proxy of insulin resistance, but the association between the TyG Index and DKD is less certain. We investigated if the TyG Index can predict DKD onset effectively.Materials and Methods: Cross-sectional and longitudinal analyses were undertaken. In total, 1432 type-2 diabetes mellitus (T2DM) patients were included in the cross-sectional analysis. The TyG Index (calculated by ln [fasting triglycerides (mg/dL) × fasting glucose (mg/dL)/2]) was split into three tertiles. Associations of the TyG Index with microalbuminuria and estimated glomerular filtration rate (eGFR) < 60 mL/min/1.73 m2 were calculated. Longitudinally, 424 patients without DKD at baseline were followed up for 21 (range, 12– 24) months. The main outcome was DKD prevalence as defined with eGFR < 60 mL/min/1.73 m2 or continuously increased urinary microalbuminuria: creatinine ratio (> 30 mg/mL) over 3 months. Cox regression was used to analyze the association between the TyG Index at baseline and DKD. Receiver operating characteristics curve (ROC) analysis was used to assess the sensitivity and specificity of the TyG Index in predicting DKD.Results: In cross-sectional analysis, patients with a higher TyG Index had a higher risk of microalbuminuria (OR = 2.342, 95% CI = 1.744– 3.144, p < 0.001), and eGFR < 60 mL/min/1.73 m2 (1.696, 95% CI =1.096– 2.625, p = 0.018). Longitudinally, 94 of 424 participants developed DKD. After confounder adjustment, patients in the high tertile of the TyG Index at baseline had a greater risk to developing DKD than those in the low tertile (HR = 1.727, 95% CI = 1.042– 2.863, p = 0.034). The area under the ROC curve was 0.69 (0.63– 0.76).Conclusion: The TyG Index is a potential predictor for DKD in T2DM patients.Clinical Trial: Clinical Trials identification number = NCT03692884.Keywords: diabetic kidney disease, triglyceride–glucose index, insulin resistance

The association between fat mass and mortality has been equivocally shown to be linear, J-shaped, and U-shaped. We aimed to clarify this relationship based on Mendelian randomization (MR) analysis and lifestyle modification.This prospective analysis included 449,831 participants from UK Biobank. Linear MR analysis was used to estimate the linear relationship between fat mass and mortality. We assessed whole body fat mass by bioimpedance analysis at baseline and categorized subjects into five equal groups based on fat mass index (FMI). The association between FMI and mortality were investigated among whole population and in subgroups stratified by individual lifestyle factors, including diet, physical activity, smoking, alcohol, sleep and psychological health.Linear MR analyses indicated a positive association between genetically predicted fat mass and all-cause mortality (HR 1.10, 95 % CI 1.08-1.12, P 0.001). The association between FMI and all-cause mortality was manifested as J-shaped (HRs across FMI categories: 1.04, 1.00, 1.07, 1.21, 1.54), which was significantly modified by the number of low-risk lifestyle factors (P for interaction0.001). When evaluating individual lifestyle factors, we observed a nonlinear relationship between FMI and all-cause mortality among participants who had high-risk lifestyle factors, while a linear relationship was observed among participants who had low-risk lifestyle factors, especially for those with adequate physical activity (HRs across FMI categories: 0.95, 1.00, 1.05, 1.17, 1.44) and who never smoked (0.96, 1.00, 1.03, 1.14, 1.51).Genetically determined fat mass is causally and linearly associated with mortality. The J-shape association between anthropometric FMI and mortality is caused by high-risk lifestyle factors.

The oxygen dissociation and the oxidized structure on the pristine C3N monolayer in exposure to air are the inevitably critical issues for the C3N engineering and surface functionalization yet have not been revealed in detail. Using the first-principles calculations, we have systematically investigated the possible O2 adsorption sites, various O2 dissociation pathways and the oxidized structures. It is demonstrated that the pristine C3N monolayer shows more O2 physisorption sites and exhibits stronger O2 adsorption than the pristine graphene. Among various dissociation pathways, the most preferable one is a two-step process involving an intermediate state with the chemisorbed O2 and the barrier is lower than that on the pristine graphene, indicating that the pristine C3N monolayer is more susceptible to oxidation than the pristine graphene. Furthermore, we found that the most stable oxidized structure is not produced by the most preferable dissociation pathway but generated from a direct dissociation process. These results can be generalized into a wide range of temperatures and pressures using ab initio atomistic thermodynamics. Our findings deepen the understanding of the chemical stability of 2D crystalline carbon nitrides under ambient conditions, and could provide insights into the tailoring of the surface chemical structures via doping and oxidation., Comment: 23 pages,8 figures

Using correlative adiabatic plasmonic nanofocused four-wave mixing and two-photon photoluminescence we image nanoscale heterogeneity, resolve few- to 10’s fs coherent dynamics, and model underlying interlayer coupling in 2D graphene/WSe2 heterostructures.

Single-photon detectors (SPDs) that can sense individual photons are the most sensitive instruments for photodetection. Established SPDs such as conventional silicon or III-V compound semiconductor avalanche diodes and photomultiplier tubes have been used in a wide range of time-correlated photon-counting applications, including quantum information technologies, in vivo biomedical imaging, time-of-flight 3D scanners, and deep-space optical communications. However, further development of these fields requires more sophisticated detectors with high detection efficiency, fast response, and photon-number-resolving ability, etc. Thereby, significant efforts have been made to improve the performance of conventional SPDs and to develop new photon-counting technologies. In this review, the working mechanisms and key performance metrics of conventional SPDs are first summarized. Then emerging photon-counting detectors (in the visible to infrared range) based on 0D quantum dots, 1D quantum nanowires, and 2D layered materials are discussed. These low-dimensional materials exhibit many exotic properties due to the quantum confinement effect. And photodetectors built from these nD-materials (n = 0, 1, 2) can potentially be used for ultra-weak light detection. By reviewing the status and discussing the challenges faced by SPDs, this review aims to provide future perspectives on the research directions of emerging photon-counting technologies.

We aim to explore the relationship between early-onset diabetes and proliferative diabetic retinopathy (PDR) in type 2 diabetes mellitus (T2DM) patients with microalbuminuria. A total of 461 T2DM patients with microalbuminuria were enrolled. Subjects were defined as early-onset or late-onset based on the age at which they were diagnosed with diabetes (

Using plasmonic nanofocusing coupled with ultrafast femtosecond pulses, we perform spatio-temporal nonlinear optical imaging of graphene and MoSe2. We resolve for the first time the nanoscale heterogeneity in the few-femtosecond coherent dynamics in two-dimensional materials.

The ability to use infrared imaging systems with multicolor capabilities, high photoresponsivity and polarization sensitivity, is central to practical photodetectors and has been demonstrated with conventional devices based on Ⅲ-Ⅴ or Ⅱ-Ⅵ semiconductors. However, the photodetectors working at room temperature with high responsivity for polarized infrared light detection remains elusive. Here, we first demonstrate a broadband photodetector using a vertical photogate heterostructure of BP-on-WSe 2 (black phosphorus-on-tungsten diselenide) in which BP serves as the photogate and WSe 2 as the conductive channel. Ultrahigh visible and infrared photoresponsivity at room temperature can reach up to ~10 3 A/W and ~5×10 −1 A/W, respectively, and ultrasensitive visible and infrared specific detectivity is obtained up to ~10 14 and ~10 10 Jones respectively at room temperature. Moreover, the high sensitivity to infrared polarization is about 40 mA/W with incident light polarized along the horizontal axis (defined as 0° polarization). This performance is due to the strong intrinsic linear dichroism of BP and the device design which can sufficiently collect the photoinduced carriers isotropically, as well as the influence from the orientation of the edge of the BP-on-WSe 2 overlapped area which is the same for all polarizations. The high responsivity, good sensitive detectivity and highly polarization-sensitive infrared photoresponse suggest that the photodetectors based on photogate structure afford new opportunities for infrared detecting or imaging at room temperature by using two-dimensional materials.

Metal-semiconductor-metal (MSM)-structured GaAs-based nanowire photodetectors have been widely reported because they are promising as an alternative for high-performance devices. Owing to the Schottky built-in electric fields in the MSM structure photodetectors, enhancements in photoresponsivity can be realized. Thus, strengthening the built-in electric field is an efficacious way to make the detection capability better. In this study, we fabricate a single GaAs nanowire MSM photodetector with superior performance by doping-adjusting the Fermi level to strengthen the built-in electric field. An outstanding responsivity of 1175 A/W is obtained. This is two orders of magnitude better than the responsivity of the undoped sample. Scanning photocurrent mappings and simulations are performed to confirm that the enhancement in responsivity is because of the increase in the hole Schottky built-in electric field, which can separate and collect the photogenerated carriers more effectively. The eloquent evidence clearly proves that doping-adjusting the Fermi level has great potential applications in high-performance GaAs nanowire photodetectors and other functional photodetectors.

The development of prefabricated building is a transformation of the traditional construction mode, a new cut-in point for the sustainable development of the construction industry, and can promote the supply-side structural reform of the construction industry in China. As an important city in the development of the western region, the development and promotion of prefabricated buildings in Chongqing has played an exemplary role for other cities. Therefore, this research provides a certain degree of theoretical exploration and practical application. In this paper, SWOT analysis is used to analyze the advantages, disadvantages, opportunities and challenges of the prefabricated building, and to gain a full understanding of the development conditions of the prefabricated building. On this basis, the paper summarizes the four major constraints on the development of prefabricated building, including policy factors, economic factors, technological factors and industrial factors, and analyzes the weight of these constraints, in view of each restriction factor proposed the corresponding solution countermeasure.

An efficient ferroelectric-enhanced side-gated single CdS nanowire (NW) ultraviolet (UV) photodetector at room temperature is demonstrated. With the ultrahigh electrostatic field from polarization of ferroelectric polymer, the depletion of the intrinsic carriers in the CdS NW channel is achieved, which significantly reduces the dark current and increases the sensitivity of the UV photodetector even after the gate voltage is removed. Meanwhile, the low frequency noise current power of the device reaches as low as 4.6 × 10−28 A2 at a source-drain voltage Vds = 1 V. The single CdS NW UV photodetector exhibits high photoconductive gain of 8.6 × 105, responsivity of 2.6 × 105 A W−1, and specific detectivity (D*) of 2.3 × 1016 Jones at a low power density of 0.01 mW cm−2 for λ = 375 nm. In addition, the spatially resolved scanning photocurrent mapping across the device shows strong photocurrent signals near the metal contacts. This is promising for the design of a controllable, high-performance, and low power consumption ultraviolet photodetector.

In recent years, 2D layered materials have been considered as promising photon absorption channel media for next-generation phototransistors due to their atomic thickness, easily tailored single-crystal van der Waals heterostructures, ultrafast optoelectronic characteristics, and broadband photon absorption. However, the photosensitivity obtained from such devices, even under a large bias voltage, is still unsatisfactory until now. In this paper, high-sensitivity phototransistors based on WS2 and MoS2 are proposed, designed, and fabricated with gold nanoparticles (AuNPs) embedded in the gate dielectric. These AuNPs, located between the tunneling and blocking dielectric, are found to enable efficient electron trapping in order to strongly suppress dark current. Ultralow dark current (10−11 A), high photoresponsivity (1090 A W−1), and high detectivity (3.5 × 1011 Jones) are obtained for the WS2 devices under a low source/drain and a zero gate voltage at a wavelength of 520 nm. These results demonstrate that the floating-gate memory structure is an effective configuration to achieve high-performance 2D electronic/optoelectronic devices.

Single-photon detectors that can resolve photon number play a key role in advanced quantum information technologies. Despite significant progress in improving conventional photon-counting detectors and developing novel device concepts, single-photon detectors that are capable of distinguishing incident photon number at room temperature are still very limited. We demonstrate a room-temperature photon-number-resolving detector by integrating a field-effect transistor configuration with core/shell-like nanowires. The shell serves as a photosensitive gate, shielding negative back-gated voltage, and leads to a persistent photocurrent. At room temperature, our detector is demonstrated to identify 1, 2, and 3 photon-number states with a confidence of >82%. The detection efficiency is determined to be 23%, and the dark count rate is 1.87 × 10-3 Hz. Importantly, benefiting from the anisotropic nature of 1D nanowires, the detector shows an intrinsic photon-polarization selection, which distinguishes itself from existing intensity single-photon detectors. The unique performance for the single-photon detectors based on single nanowire demonstrates the great potential for future single-photon detection applications.

Molybdenum disulfide (MoS

2D Molybdenum disulfide (MoS2 ) is a promising candidate material for high-speed and flexible optoelectronic devices, but only with low photoresponsivity. Here, a large enhancement of photocurrent response is obtained by coupling few-layer MoS2 with Au plasmonic nanostructure arrays. Au nanoparticles or nanoplates placed onto few-layer MoS2 surface can enhance the local optical field in the MoS2 layer, due to the localized surface plasmon (LSP) resonance. After depositing 4 nm thick Au nanoparticles sparsely onto few-layer MoS2 phototransistors, a doubled increase in the photocurrent response is observed. The photocurrent of few-layer MoS2 phototransistors exhibits a threefold enhancement with periodic Au nanoarrays. The simulated optical field distribution confirms that light can be trapped and enhanced near the Au nanoplates. These findings offer an avenue for practical applications of high performance MoS2 -based optoelectronic devices or systems in the future.

Low dimensional semiconductors have attracted enormous attention in recent years. Owing to the special dimension confinement, photodetectors based on low dimensional materials and their hybrid systems exhibit considerable performance at room temperature. This differs from traditional thin-film infrared photodetectors which require liquid nitrogen cooling. In this paper, we introduce uncooled photodetectors based on one dimensional (1D) nanowires, two-dimensional (2D) materials, 2D hybrid structures and 1D/2D heterostructures. We illustrate their working mechanisms and reveal the potential for practical infrared detection.

Two-dimensional materials are promising candidates for electronic and optoelectronic applications. MoTe2 has an appropriate bandgap for both visible and infrared light photodetection. Here we fabricate a high-performance photodetector based on few-layer MoTe2. Raman spectral properties have been studied for different thicknesses of MoTe2. The photodetector based on few-layer MoTe2 exhibits broad spectral range photodetection (0.6-1.55 μm) and a stable and fast photoresponse. The detectivity is calculated to be 3.1 × 10(9) cm Hz(1/2) W(-1) for 637 nm light and 1.3 × 10(9) cm Hz(1/2) W(-1) for 1060 nm light at a backgate voltage of 10 V. The mechanisms of photocurrent generation have been analyzed in detail, and it is considered that a photogating effect plays an important role in photodetection. The appreciable performance and detection over a broad spectral range make it a promising material for high-performance photodetectors.

One-dimensional InAs nanowires (NWs) have been widely researched in recent years. Features of high mobility and narrow bandgap reveal its great potential of optoelectronic applications. However, most reported work about InAs NW-based photodetectors is limited to the visible waveband. Although some work shows certain response for near-infrared light, the problems of large dark current and small light on/off ratio are unsolved, thus significantly restricting the detectivity. Here in this work, a novel "visible light-assisted dark-current suppressing method" is proposed for the first time to reduce the dark current and enhance the infrared photodetection of single InAs NW photodetectors. This method effectively increases the barrier height of the metal-semiconductor contact, thus significantly making the device a metal-semiconductor-metal (MSM) photodiode. These MSM photodiodes demonstrate broadband detection from less than 1 μm to more than 3 μm and a fast response of tens of microseconds. A high detectivity of ∼10

All-inorganic cesium lead halide perovskite (CsPbX3, X = Cl, Br, and I) nanocrystals (NCs) are emerging as an important class of semiconductor materials with superior photophysical properties and wide potential applications in optoelectronic devices. So far, only a few studies have been conducted to control the shape and geometry of CsPbX3 NCs. Here we report a general approach to directly synthesize two-dimensional (2D) CsPbX3 perovskite and mixed perovskite nanosheets with uniform and ultrathin thicknesses down to a few monolayers. The key to the high-yield synthesis of perovskite nanosheets is the development of a new Cs-oleate precursor. The as-synthesized CsPbX3 nanosheets exhibit bright photoluminescence with broad wavelength tunability by composition modulation. The excellent optoelectronic properties of CsPbX3 nanosheets combined with their unique 2D geometry and large lateral dimensions make them ideal building blocks for building functional devices. To demonstrate their potential applications in optoelectronics, photodetectors based on CsPbBr3 nanosheets are fabricated, which exhibit high on/off ratios with a fast response time.

Molybdenum disulfide (MoS2 ), a typical 2D metal dichalcogenide (2DMD), has exhibited tremendous potential in optoelectronic device applications, especially in photodetection. However, due to the weak light absorption of planar mono-/multilayers, limited cutoff wavelength edge, and lack of high-quality junctions, most reported MoS2 -based photodetectors show undesirable performance. Here, a structurized 3D heterojunction of RGO-MoS2 /pyramid Si is demonstrated via a simple solution-processing method. Owing to the improved light absorption by the pyramid structure, the narrowed bandgap of the MoS2 by the imperfect crystallinity, and the enhanced charge separation/transportation by the inserted reduced graphene oxide (RGO), the assembled photodetector exhibits excellent performance in terms of a large responsivity of 21.8 A W-1 , extremely high detectivity up to 3.8 × 1015 Jones (Jones = cm Hz1/2 W-1 ) and ultrabroad spectrum response ranging from 350 nm (ultraviolet) to 4.3 µm (midwave infrared). These device parameters represent the best results for MoS2 -based self-driven photodetectors, and the detectivity value sets a new record for the 2DMD-based photodetectors reported thus far. Prospectively, the design of novel 3D heterojunction can be extended to other 2DMDs, opening up the opportunities for a host of high-performance optoelectronic devices.

The gastric bacterial pathogen Helicobacter pylori persistently colonizes the gastric mucosa of humans and plays a critical role in the development of gastritis, peptic ulceration and gastric adenocarcinoma. Consequently, the eradication of H. pylori might contribute to the prevention of H. pylori-associated gastric diseases. In this study, a multi-epitope vaccine CTB-UE (CUE) was displayed on the surface of non-genetically modified Lactococcus lactis particles (GEM) to enhance immunogenicity. This particulate vaccine CUE-GEM induced serum and mucosal specific antibody responses against native H. pylori urease and provided potent protection to eliminate H. pylori colonization and relieve gastritis in an H. pylori-infected BALB/c mouse model. The immuno-protective mechanisms are highly associated with CD4(+) Th cell-mediated and humoral immunity, especially local immunity. There might be two main aspects of this association. One aspect is related to the suppression of urease activity by promotion of the production of specific mucosal neutralizing antibody. The other aspect is correlated with alleviating gastritis by regulating the gastric pro-inflammatory cytokine profile, especially IFN-γ and IL-17. These results demonstrated that conjugating antigen vaccines with GEM particles could lead to promising oral therapeutic vaccine formulations against H. pylori infection.

MoS2 is a promising candidate material for high speed optoelectronic devices, but with low photoresponsivity. Recently, we reported a large enhancement of photocurrent response by coupling few-layer MoS2 with Au nanoparticles or periodic Au nanoarrays[1].

An advanced visible/infrared dual-band photodetector with high-resolution imaging at room temperature is proposed and demonstrated for intelligent identification based on the 2D GaSe/GaSb vertical heterostructure. It resolves the challenges of producing large-scale 2D growth, achieving fast response speed, outstanding detectivity, and lower manufacture cost, which are the main obstacles for industrialization of 2D-materials-based photodetection.

Epidemiologic studies have provided solid evidence for the neurotoxic effect of lead for decades of years. In view of the fact that children are more vulnerable to the neurotoxicity of lead, lead exposure has been an urgent public health concern for decades of years. The modes of action of lead neurotoxic effects include disturbance of neurotransmitter storage and release, damage of mitochondria, as well as induction of apoptosis in cerebrovascular endothelial cells, astroglia and oligodendroglia. Our studies here, from a novel point of view, demonstrates that lead specifically caused induction of COX-2, a well known inflammatory mediator in neurons and glia cells. Furthermore, we revealed that COX-2 was induced by lead in a transcription-dependent manner, which relayed on transcription factor NFAT, rather than AP-1 and NFκB, in glial cells. Considering the important functions of COX-2 in mediation of inflammation reaction and oxidative stress, our studies here provide a mechanistic insight into the understanding of lead-associated inflammatory neurotoxicity effect via activation of pro-inflammatory NFAT3/COX-2 axis.

The aim of the work reported is to design and develop a kind of data acquisition system for pulmonary function based on flow sensor. The hardware design includes the collection of sensor signal, single-chip microcomputer (SCM), flow sensor and their electro circuit schematics. The system employs a flow sensor FS1022CL, which is specially configured for pulmonary function meter, to measure the flow rate, coupled with the SCM AT89S52. Vital capacity data acquired by the flow sensor is transmitted to a software platform, where data processing software runs in order to calculate the volume of a gas. Delphi is used to complete the design of the software platform, in order to realize data analysis and error compensation. Experimental results show that this system could calculate the gas volume, and provide the vital capacity for the pulmonary function meter.

Excellent scalability of a novel Cu x Si y O emRRAM down to 22 nm node is demonstrated based on statistical data of 1 Mb test chip for the first time. The integration utilizes the standard logic process and the RRAM size is shrunk by spacer pattern technology. The reset current decreases by 5X from 130nm to 22nm node with maintaining robust data retention (10yrs. @150°C), good resistance distribution (with 10X window @125°C), significant read disturbance immunity (after 1010 cycles @0.5V, 50ns pulse), acceptable fast speed (set 100ns; reset 60us), and competitive cost effectiveness (no dedicated tools). This solution is promising in the advanced logic node for SOC applications of post-emFLASH era.

This work studies the electrical and testing reliability issues of Cu x O based RRAM (Resistive Random Access Memory). Firstly, we study the most important electrical reliability issue-data retention capability, and propose a filament/charge trap combined model to clarify the retention failure mechanism. Secondly, we respectively study the reliability problems caused by the SET compliance current in 1R-architecture and 1T1R-architecture devices during the electrical testing, and observe the compliance current overshoot phenomenon for the first time in 1R-architecture device by using a self-build compliance current capturing system.

We demonstrate coherent spatio-temporal nano-imaging of graphene and its plasmonic nano-structures in four-wave mixing through adiabatic plasmonic nanofocusing. We resolve nanoscale heterogeneity and ultrafast dephasing affected by weakly screened carrier-carrier scattering.