Search

Thermoresponsive polymer coatings on cell culture substrates enable noninvasive cell detachment and cell sheet fabrication for biomedical applications. Optimized coatings should support controlled culture and detachment of various cell types and allow chemical modifications, e.g., to introduce specific growth factors for enhanced gene expression. Furthermore, the sterilization and storage stability of the coatings must be assessed for translational attempts. Poly(glycidyl ether) ( PGE ) brush coatings with short alkoxy side chains provide a versatile platform for cell culture and detachment, but their polyether backbones are susceptible to oxidation and degradation. Thus, we rationally designed potential alternatives with thermoresponsive glycerol-based block copolymers comprising a stable polyacrylate or polymethacrylate backbone and an oligomeric benzophenone (BP)-based anchor. The resulting poly(ethoxy hydroxypropyl acrylate- b -benzophenone acrylate) ( pEHPA- b -BP ) and poly(ethoxy hydroxypropyl methacrylate- b -benzophenone methacrylate) ( pEHPMA- b -BP ) block copolymers preserve the short alkoxy-terminated side chains of the PGE derived structure on a stable, but hydrophobic, aliphatic backbone. The amphiphilicity balance is maintained through incorporated hydroxyl groups, which simultaneously can be used for chemical modification. The polymers were tailored into brush coatings on polystyrene surfaces via directed adsorption using the BP oligomer anchor. The resulting coatings with thickness values up to ∼3 nm supported efficient adhesion and proliferation of human fibroblasts despite minimal protein adsorption. The conditions for cell sheet fabrication on pEHPA- b -BP were gentler and more reliable than on pEHPMA- b -BP , which required additional cooling. Hence, the stability of pEHPA- b -BP and PGE coatings was evaluated post gamma and formaldehyde (FO) gas sterilization. Gamma sterilization partially degraded PGE coatings and hindered cell detachment on pEHPA- b -BP . In contrast, FO sterilization only slowed detachment on PGE coatings and had no adverse effects on pEHPA- b -BP , maintaining their efficient performance in cell sheet fabrication.

Intestinal parasitic worms are widespread throughout the world, causing chronic infections in humans and animals. However, very little is known about the locomotion of the worms in the host gut. We studied the movement of Heligmosomoides bakeri, naturally infecting mice, and used as an animal model for roundworm infections. We investigated the locomotion of H. bakeri in simplified environments mimicking key physical features of the intestinal lumen, i.e. medium viscosity and intestinal villi topology. We found that the motion sequence of these nematodes is non-periodic, but the migration could be described by transient anomalous diffusion. Aggregation as a result of biased, enhanced-diffusive locomotion of nematodes in sex-mixed groups was detected. This locomotion is probably stimulated by mating and reproduction, while single nematodes move randomly (diffusive). Natural physical obstacles such as high mucus-like viscosity or villi topology slowed down but did not entirely prevent nematode aggregation. Additionally, the mean displacement rate of nematodes in sex-mixed groups of 3.0 × 10 -3 mm s -1 in a mucus-like medium is in good agreement with estimates of migration velocities of 10 -4 to 10 -3 mm s -1 in the gut. Our data indicate H. bakeri motion to be non-periodic and their migration random (diffusive-like), but triggerable by the presence of kin.

Vascular surgery faces a critical demand for novel vascular grafts that are biocompatible and thromboresistant. This urgency particularly applies to bypass operations involving small caliber vessels. In the realm of tissue engineering, the development of fully vascularized organs holds great promise as a solution to organ shortage for transplantation. To achieve this, it is imperative to (re-)construct a biocompatible and non-thrombogenic vascular network within these organs. In this systematic review, we identify, classify and discuss basic principles and methods used to perform in vitro/ex vivo dynamic thrombogenicity testing of perfusable tissue engineered organs and tissues. We conducted a pre-registered systematic review of studies published in the last 23 years according to PRISMA-P Guidelines, comprising a systematic data extraction, in-depth analysis and risk of bias assessment of 116 included studies. We identified shaking (n=28), flow loop (n=17), ex vivo (arterio-venous shunt, n=33) and dynamic in vitro models (n=38) as main approaches for thrombogenicity assessment. This comprehensive review unveils a prevalent lack of standardization and serves as a valuable guide in the design of standardized experimental setups.

The luminal surface of the intestinal epithelium is protected by a vital mucus layer, which is essential for lubrication, hydration, and fostering symbiotic bacterial relationships. Replicating and studying this complex mucus structure in vitro presents considerable challenges. To address this, we developed a hydrogel-integrated millifluidic tissue chamber capable of applying precise apical shear stress to intestinal models cultured on flat or 3D structured hydrogel scaffolds with adjustable stiffness. The chamber is designed to accommodate nine hydrogel scaffolds, 3D-printed as flat disks with a storage modulus matching the physiological range of intestinal tissue stiffness (~3.7 kPa) from bioactive decellularized and methacrylated small intestinal submucosa (dSIS-MA). Computational fluid dynamics simulations were conducted to confirm a laminar flow profile for both flat and 3D villi-comprising scaffolds in the physiologically relevant regime. The system was initially validated with HT29-MTX seeded hydrogel scaffolds, demonstrating accelerated differentiation, increased mucus production, and enhanced 3D organization under shear stress. These characteristic intestinal tissue features are essential for advanced in vitro models as they critically contribute to a functional barrier. Subsequently, the chamber was challenged with human intestinal stem cells (ISCs) from the terminal ileum. Our findings indicate that biomimicking hydrogel scaffolds, in combination with physiological shear stress, promote multi-lineage differentiation, as evidenced by a gene and protein expression analysis of basic markers and the 3D structural organization of ISCs in the absence of chemical differentiation triggers. The quantitative analysis of the alkaline phosphatase (ALP) activity and secreted mucus demonstrates the functional differentiation of the cells into enterocyte and goblet cell lineages. The millifluidic system, which has been developed and optimized for performance and cost efficiency, enables the creation and modulation of advanced intestinal models under biomimicking conditions, including tunable matrix stiffness and varying fluid shear stresses. Moreover, the readily accessible and scalable mucus-producing cellular tissue models permit comprehensive mucus analysis and the investigation of pathogen interactions and penetration, thereby offering the potential to advance our understanding of intestinal mucus in health and disease.

Decellularized extracellular matrix (dECM) is an excellent natural source for 3D bioprinting materials due to its inherent cell compatibility. In vat photopolymerization, the use of dECM-based bioresins is just emerging, and extensive research is needed to fully exploit their potential. In this study, two distinct methacryloyl-functionalized, photocrosslinkable dECM-based bioresins were prepared from digested porcine liver dECM through functionalization with glycidyl methacrylate (GMA) or conventional methacrylic anhydride (MA) under mild conditions for systematic comparison. Although the chemical modifications did not significantly affect the structural integrity of the dECM proteins, mammalian cells encapsulated in the respective hydrogels performed differently in long-term culture. In either case, photocrosslinking during 3D (bio)printing resulted in transparent, highly swollen, and soft hydrogels with good shape fidelity, excellent biomimetic properties and tunable mechanical properties (~ 0.2-2.5 kPa). Interestingly, at a similar degree of functionalization (DOF ~ 81.5-83.5 %), the dECM-GMA resin showed faster photocrosslinking kinetics in photorheology resulting in lower final stiffness and faster enzymatic biodegradation compared to the dECM-MA gels, yet comparable network homogeneity as assessed via Brillouin imaging. While human hepatic HepaRG cells exhibited comparable cell viability directly after 3D bioprinting within both materials, cell proliferation and spreading were clearly enhanced in the softer dECM-GMA hydrogels at a comparable degree of crosslinking. These differences were attributed to the additional hydrophilicity introduced to dECM via methacryloylation through GMA compared to MA. Due to its excellent printability and cytocompatibility, the functional porcine liver dECM-GMA biomaterial enables the advanced biofabrication of soft 3D tissue analogs using vat photopolymerization-based bioprinting., Competing Interests: Declaration of competing interest The authors declare the following financial interests/personal relationships which may be considered as potential competing interests: Marie Weinhart reports financial support was provided by German Research Foundation. Sebastian Seiffert reports financial support was provided by German Research Foundation. Beate Koksch reports financial support was provided by German Research Foundation. Igor Maximilian Sauer reports financial support was provided by German Research Foundation. If there are other authors, they declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Authors. Published by Elsevier B.V. All rights reserved.)

Solubilized, gel-forming decellularized extracellular matrix (dECM) is used in a wide range of basic and translational research and due to its inherent bioactivity can promote structural and functional tissue remodeling. The animal-derived protease pepsin has become the standard proteolytic enzyme for the solubilization of almost all types of collagen-based dECM. In this study, pepsin was compared with papain, α-amylase, and collagenase for their potential to solubilize porcine liver dECM. Maximum preservation of bioactive components and native dECM properties was used as a decisive criterion for further application of the enzymes, with emphasis on minimal destruction of the protein structure and maintained capacity for physical thermogelation at neutral pH. The solubilized dECM digests, and/or their physically gelled hydrogels were characterized for their rheological properties, gelation kinetics, GAG content, proteomic composition, and growth factor profile. This study highlights papain as a plant-derived enzyme that can serve as a cost-effective alternative to animal-derived pepsin for the efficient solubilization of dECM. The resulting homogeneous papain-digested dECM preserved its thermally triggered gelation properties similar to pepsin digests, and the corresponding dECM hydrogels demonstrated their enhanced bioadhesiveness in single-cell force spectroscopy experiments with fibroblasts. The viability and proliferation of human HepaRG cells on dECM gels were similar to those on pure rat tail collagen type I gels. Papain is not only highly effective and economically attractive for dECM solubilization but also particularly interesting when digesting human-tissue-derived dECM for regenerative applications, where animal-derived materials are to be avoided.

New experimental approaches for tissue repair have recently been proposed and include the application of natural or synthetic biomaterials and immune cells. Herein, fully synthetic poly(glycidyl ether) (PGE) copolymer coatings are evaluated as bioinstructive materials for the in vitro culture and intrinsic activation of human immune cells. Immature monocyte-derived dendritic cells (moDCs) are exposed to PGE brush and gel coatings of varying copolymer composition, wettability, and deformability immobilized on polystyrene culture dishes. Compared to moDCs cultured on standard tissue culture-treated polystyrene, activation marker levels on the cell surface are strongly enhanced on PGE substrates. Thereby, moDCs undergo a distinct morphological change and reach levels of activation comparable to those achieved by toll-like receptor (TLR) ligand liposaccharide (LPS), specifically for the expression of costimulatory molecules CD86 and CD40 as well as human leukocyte antigen (HLA)-DR. In addition, PGE coatings induce a significantly enhanced level of programmed cell death ligands 1 and 2 (PD-L1/-L2) on the moDC surface, two molecules crucially involved in maintaining immune tolerance. In addition, an increased release of matrix metalloproteinases MMP-1 and MMP-7, as well as transforming growth factor (TGF)-β1 and epidermal growth factor (EGF) was observed in moDCs cultured on PGE substrates. As fully synthetic biomaterials, PGE coatings demonstrate intrinsic functional competence in instructing immature human moDCs for phenotypic activation in vitro, accompanied by the secretion of bioactive molecules, which are known to be crucial for tissue regeneration. Hence, PGE coatings hold strong potential for immune-modulating implant coatings, while PGE-activated moDCs are promising candidates for future clinical cell-based immunoengineering therapies., Competing Interests: The authors declare the following financial interests/personal relationships which may be considered as potential competing interests: Marie Weinhart, Matthias Peiser, and Daniel D. Stöbener have filed a patent METHOD FOR ACTIVATING DENDRITIC CELLS pending to Freie Universität Berlin., (© 2023 The Authors.)

Thanks to its natural complexity and functionality, decellularized extracellular matrix (dECM) serves as an excellent foundation for creating highly cell-compatible bioinks and bioresins. This enables the bioprinted cells to thrive in an environment that closely mimics their native ECM composition and offers customizable biomechanical properties. To formulate dECM bioinks and bioresins, one must first pulverize and/or solubilize the dECM into non-crosslinked fragments, which can then be chemically modified as needed. In bioprinting, the solubilized dECM-derived material is typically deposited and/or crosslinked in a layer-by-layer fashion to build 3D hydrogel structures. Since the introduction of the first liver-derived dECM-based bioinks, a wide variety of decellularized tissue have been employed in bioprinting, including kidney, heart, cartilage, and adipose tissue among others. This review aims to summarize the critical steps involved in tissue-derived dECM bioprinting, starting from the decellularization of the ECM to the standardized formulation of bioinks and bioresins, ultimately leading to the reproducible bioprinting of tissue constructs. Notably, this discussion also covers photocrosslinkable dECM bioresins, which are particularly attractive due to their ability to provide precise spatiotemporal control over the gelation in bioprinting. Both in extrusion printing and vat photopolymerization, there is a need for more standardized protocols to fully harness the unique properties of dECM-derived materials. In addition to mammalian tissues, the most recent bioprinting approaches involve the use of microbial extracellular polymeric substances in bioprinting of bacteria. This presents similar challenges as those encountered in mammalian cell printing and represents a fascinating frontier in bioprinting technology., Competing Interests: The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (© 2023 The Authors.)

Non-temperature-induced effects of radiofrequency electromagnetic fields (RF) have been controversial for decades. Here, we established measurement techniques to prove their existence by investigating energy deposition in tumor cells under RF exposure and upon adding amplitude modulation (AM) (AMRF). Using a preclinical device LabEHY-200 with a novel in vitro applicator, we analyzed the power deposition and system parameters for five human colorectal cancer cell lines and measured the apoptosis rates in vitro and tumor growth inhibition in vivo in comparison to water bath heating. We showed enhanced anticancer effects of RF and AMRF in vitro and in vivo and verified the non-temperature-induced origin of the effects. Furthermore, apoptotic enhancement by AM was correlated with cell membrane stiffness. Our findings not only provide a strategy to significantly enhance non-temperature-induced anticancer cell effects in vitro and in vivo but also provide a perspective for a potentially more effective tumor therapy.

The bioengineering of artificial tissue constructs requires special attention to their fast vascularization to provide cells with sufficient nutrients and oxygen. We addressed the challenge of in vitro vascularization by employing a combined approach of cell sheet engineering, 3D printing, and cellular self-organization in dynamic maturation culture. A confluent cell sheet of human umbilical vein endothelial cells (HUVECs) was detached from a thermoresponsive cell culture substrate and transferred onto a 3D-printed, perfusable tubular scaffold using a custom-made cell sheet rolling device. Under indirect co-culture conditions with human dermal fibroblasts (HDFs), the cell sheet-covered vessel mimic embedded in a collagen gel together with additional singularized HUVECs started sprouting into the surrounding gel, while the suspended cells around the tube self-organized and formed a dense lumen-containing 3D vascular network throughout the gel. The HDFs cultured below the HUVEC-containing cell culture insert provided angiogenic support to the HUVECs via molecular crosstalk without competing for space with the HUVECs or inducing rapid collagen matrix remodeling. The resulting vascular network remained viable under these conditions throughout the 3 week cell culture period. This static indirect co-culture setup was further transferred to dynamic flow conditions, where the medium perfusion was enabled via two independently addressable perfusion circuits equipped with two different cell culture chambers, one hosting the HDFs and the other hosting the HUVEC-laden collagen gel. Using this system, we successfully connected the collagen-embedded HUVEC culture to a dynamic medium flow, and within 1 week of the dynamic cell culture, we detected angiogenic sprouting and dense microvascular network formation via HUVEC self-organization in the hydrogel. Our approach of combining a 3D-printed and cell sheet-covered vascular precursor that retained its sprouting capacity together with the self-assembling HUVECs in a dynamic perfusion culture resulted in a vascular-like 3D network, which is a critical step toward the long-term vascularization of bioengineered in vitro tissue constructs., (Creative Commons Attribution license.)

Thermoresponsive poly(glycidyl ether) (PGE) brushes have shown to be viable substrates for the culture and temperature-triggered detachment of confluent cell sheets. Surface-tethered PGEs with a cloud point temperature (T CP ) around ~30 °C exhibit phase transitions well-centered within the physiological range (20-37 °C), which makes them ideal candidates for cell sheet fabrication. However, PGEs with T CP s at ~20 °C also afford the detachment of various types of cell sheets, even at room temperature (20-23 °C), i.e., above the polymers' T CP s. In this study, we investigate the phase transition of PGE brushes tethered to polystyrene (PS) culture substrates with varying grafting density and T CP to arrive at a mechanistic understanding of their functionality in cell sheet fabrication. Using quartz crystal microbalance with dissipation (QCM-D) monitoring, we demonstrate that brushes fabricated from PGEs with T CP s at ~20 °C display volume phase transition temperatures (VPTTs) well below room temperature. Although the investigated coatings obviously do not exhibit marked thermal switching in terms of brush hydration and layer thickness, their physical properties at the brush-water interface, as ascertained by QCM-D and AFM measurements, undergo subtle changes upon cooling from 37 °C to room temperature which is sufficient to promote cell sheet detachment. Thus, it appears that discreet rehydration of the outmost brush layer, resembling "fuzzy hair" at the brush-water interface, renders the surfaces less protein- and cell-adhesive at room temperature. This minor structural change of the interface allows for the reliable detachment of human dermal fibroblast sheets already at 20 °C well above the VPTT of the brushes., Competing Interests: Declaration of competing interest The authors declare no competing interests., (Copyright © 2022 Elsevier B.V. All rights reserved.)

The relevance of cellular in vitro models highly depends on their ability to mimic the physiological environment of the respective tissue or cell niche. Static culture conditions are often unsuitable, especially for endothelial models, since they completely neglect the physiological surface shear stress and corresponding reactions of endothelial cells (ECs) such as alignment in the direction of flow. Furthermore, formation and maturation of the glycocalyx, the essential polysaccharide layer covering all endothelial surfaces and regulating diverse processes, is highly dependent on applied fluid flow. This fragile but utterly important macromolecular layer is hard to analyze, its importance is often underestimated and accordingly neglected in many endothelial models. Therefore, we exposed human umbilical vein ECs (HUVECs) and human induced pluripotent stem cell-derived ECs (iPSC-ECs) as two relevant EC models in a side-by-side comparison to static and physiological dynamic (6.6 dyn cm -2 ) culture conditions. Both cell types demonstrated an elongation and alignment along the flow direction, some distinct changes in glycocalyx composition on the surface regarding the main glycosaminoglycan components heparan sulfate, chondroitin sulfate or hyaluronic acid as well as an increased and thereby improved glycocalyx thickness and functionality when cultured under homogeneous fluid flow. Thus, we were able to demonstrate the maturity of the employed iPSC-EC model regarding its ability to sense fluid flow along with the general importance of physiological shear stress for glycocalyx formation. Additionally, we investigated EC monolayer integrity with and without application of surface shear stress, revealing a comparable existence of tight junctions for all conditions and a reorganization of the cytoskeleton upon dynamic culture leading to an increased formation of focal adhesions. We then fabricated cell sheets of EC monolayers after static and dynamic culture via non-enzymatic detachment using thermoresponsive polymer coatings as culture substrates. In a first proof-of-concept we were able to transfer an aligned iPSC-EC sheet to a 3D-printed scaffold thereby making a step in the direction of vascular modelling. We envision these results to be a valuable contribution to improvements of in vitro endothelial models and vascular engineering in the future., Competing Interests: The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest., (Copyright © 2022 Lindner, Laporte, Elomaa, Lee-Thedieck, Olmer and Weinhart.)

Vascular-disrupting agents are an interesting class of anticancer compounds because of their combined mode of action in preventing new blood vessel formation and disruption of already existing vasculature in the immediate microenvironment of solid tumors. The validation of vascular disruption properties of these drugs in vitro is rarely addressed due to the lack of proper in vitro angiogenesis models comprising mature and long-lived vascular-like networks. We herein report an indirect coculture model of human umbilical vein endothelial cells (HUVECs) and human dermal fibroblasts (HDFs) to form three-dimensional profuse vascular-like networks. HUVECs embedded and sandwiched in the collagen scaffold were cocultured with HDFs located outside the scaffold. The indirect coculture approach with the vascular endothelial growth factor (VEGF) producing HDFs triggered the formation of progressively maturing lumenized vascular-like networks of endothelial cells within less than 7 days, which have proven to be viably maintained in culture beyond day 21. Molecular weight-dependent Texas red-dextran permeability studies indicated high vascular barrier function of the generated networks. Their longevity allowed us to study the dose-dependent response upon treatment with the three known antiangiogenic and/or vascular disrupting agents brivanib, combretastatin A4 phosphate (CA4P), and 6´-sialylgalactose (SG) via semi-quantitative brightfield and qualitative confocal laser scanning microscopic (CLSM) image analysis. Compared to the reported data on in vivo efficacy of these drugs in terms of antiangiogenic and vascular disrupting effects, we observed similar trends with our 3D model, which are not reflected in conventional in vitro angiogenesis assays. High-vascular disruption under continuous treatment of the matured vascular-like network was observed at concentrations ≥3.5 ng·ml -1 for CA4P and ≥300 nM for brivanib. In contrast, SG failed to induce any significant vascular disruption in vitro . This advanced model of a 3D vascular-like network allows for testing single and combinational antiangiogenic and vascular disrupting effects with optimized dosing and may thus bridge the gap between the in vitro and in vivo experiments in validating hits from high-throughput screening. Moreover, the physiological 3D environment mimicking in vitro assay is not only highly relevant to in vivo studies linked to cancer but also to the field of tissue regeneration., Competing Interests: The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest., (Copyright © 2022 Yavvari, Laporte, Elomaa, Schraufstetter, Pacharzina, Daberkow, Hoppensack and Weinhart.)

The recent crystallization of the neuropeptide Y Y 1 receptor (Y 1 R) in complex with the argininamide-type Y 1 R selective antagonist UR-MK299 ( 2 ) opened up a new approach toward structure-based design of nonpeptidic Y 1 R ligands. We designed novel fluorescent probes showing excellent Y 1 R selectivity and, in contrast to previously described fluorescent Y 1 R ligands, considerably higher (∼100-fold) binding affinity. This was achieved through the attachment of different fluorescent dyes to the diphenylacetyl moiety in 2 via an amine-functionalized linker. The fluorescent ligands exhibited picomolar Y 1 R binding affinities (p K i values of 9.36-9.95) and proved to be Y 1 R antagonists, as validated in a Fura-2 calcium assay. The versatile applicability of the probes as tool compounds was demonstrated by flow cytometry- and fluorescence anisotropy-based Y 1 R binding studies (saturation and competition binding and association and dissociation kinetics) as well as by widefield and total internal reflection fluorescence (TIRF) microscopy of live tumor cells, revealing that fluorescence was mainly localized at the plasma membrane.

Thermally "switchable" poly(glycidyl ether) (PGE) brushes constitute effective coatings for the temperature-triggered harvest of confluent cell sheets. Based on a simple "grafting-to" approach, such coatings can be tethered to various applied plastic culture substrate materials. Herein, we elucidate the self-assembly of PGE brushes with tunable grafting densities up to 0.12 and 0.22 chains nm -2 on polystyrene (PS) and tissue culture PS (TCPS), respectively. In terms of temperature-dependent wettability and protein adsorption, we found that brushes exhibit distinct grafting density-dependent properties which correlate with their cell sheet fabrication performance. In addition, temperature-ramped quartz-crystal microbalance with dissipation (QCM-D) measurements revealed marked substrate-specific PGE phase transitions which allowed us to deduce comprehensive switching mechanisms. Thus, we demonstrate that brushes tethered to hydrophilic TCPS (contact angle (CA) ∼ 60°) undergo a "cushioned" transition comprising a non-switchable, hydrated basal layer as well as a switchable top layer which regulates cell sheet detachment. In contrast, PGE brushes tethered to PS undergo a "grounded" transition which is substantially influenced by the dehydrating effect of the less hydrophilic PS substrate (CA ∼ 90°). These divergent phase transition mechanisms give rise to a broad scope in cell sheet fabrication performance, yielding staggered detachment times within a 30 min to 3 h range. Hence, we emphasize the importance of a detailed knowledge on the effect of applied culture substrates on the thermal switchability and phase transition characteristics of thermoresponsive brush coatings to accomplish an optimized design for functional cell culture dishes. STATEMENT OF SIGNIFICANCE: As the first comparative study of its kind, we elucidate the substrate-dependent thermal switchability of thermoresponsive brush coatings and evaluate their grafting density-dependent phase transition mechanism and its effect on cell sheet fabrication performance., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2021 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.)

Background: Since autologous veins are unavailable when needed in more than 20% of cases in vascular surgery, the production of personalized biological vascular grafts for implantation has become crucial. Surface modification of decellularized xenogeneic grafts with vascular cells to achieve physiological luminal coverage and eventually thromboresistance is an important prerequisite for implantation. However, ex vivo thrombogenicity testing remains a neglected area in the field of tissue engineering of vascular grafts due to a multifold of reasons., Methods: After seeding decellularized bovine carotid arteries with human endothelial progenitor cells and umbilical cord-derived mesenchymal stem cells, luminal endothelial cell coverage (LECC) was correlated with glucose and lactate levels on the cell supernatant. Then a closed loop whole blood perfusion system was designed. Recellularized grafts with a LECC > 50% and decellularized vascular grafts were perfused with human whole blood for 2 h. Hemolysis and complete blood count evaluation was performed on an hourly basis, followed by histological and immunohistochemical analysis., Results: While whole blood perfusion of decellularized grafts significantly reduced platelet counts, platelet depletion from blood resulting from binding to re-endothelialized grafts was insignificant (p = 0.7284). Moreover, macroscopic evaluation revealed thrombus formation only in the lumen of unseeded grafts and histological characterization revealed lack of CD41 positive platelets in recellularized grafts, thus confirming their thromboresistance., Conclusion: In the present study we were able to demonstrate the effect of surface modification of vascular grafts in their thromboresistance in an ex vivo whole blood perfusion system. To our knowledge, this is the first study to expose engineered vascular grafts to human whole blood, recirculating at high flow rates, immediately after seeding., (© 2021. The Author(s).)

We present a thermodynamic study of the interaction of synthetic, linear polyelectrolytes with bovine serum albumin (BSA). All polyelectrolytes are based on poly(allyl glycidyl ether) which has been modified by polymer-analogous reaction with anionic (-SO 3 Na), cationic (-NH 3 Cl or -NHMe 2 Cl) or zwitterionic groups (-NMe 2 (CH 2 ) 3 SO 3 ). While the anionic polymer shows a very weak interaction, the zwitterionic polymer exhibits no interaction with BSA (pI = 4.7) under the applied pH = 7.4, ionic strength (I = 23-80 mM) and temperature conditions (T = 20-37 °C). A strong binding, however, was observed for the polycations bearing primary amino or tertiary dimethyl amino groups, which could be analysed in detail by isothermal titration calorimetry (ITC). The analysis was done using an expression which describes the free energy of binding, Δ G b , as the function of the two decisive variables, temperature, T , and salt concentration, c s . The underlying model splits Δ G b into a term related to counterion release and a term related to water release. While the number of released counter ions is similar for both systems, the release of bound water is more important for the primary amine compared to the tertiary N , N -dimethyl amine presenting polymer. This finding is further traced back to a closer contact of the polymers' protonated primary amino groups in the complex with oppositely charged moieties of BSA as compared to the bulkier protonated tertiary amine groups. We thus present an investigation that quantifies both driving forces for electrostatic binding, namely counterion release and change of hydration, which contribute to a deeper understanding with direct impact on future advancements in the biomedical field.

Gastrointestinal (GI) mucus plays a pivotal role in the tissue homoeostasis and functionality of the gut. However, due to the shortage of affordable, realistic in vitro GI models with a physiologically relevant mucus layer, studies with deeper insights into structural and compositional changes upon chemical or physical manipulation of the system are rare. To obtain an improved mucus-containing cell model, we developed easy-to-use, reusable culture chambers that facilitated the application of GI shear stresses (0.002-0.08 dyn∙cm -2 ) to cells on solid surfaces or membranes of cell culture inserts in bioreactor systems, thus making them readily accessible for subsequent analyses, e.g., by confocal microscopy or transepithelial electrical resistance (TEER) measurement. The human mucus-producing epithelial HT29-MTX cell-line exhibited superior reorganization into 3-dimensional villi-like structures with highly proliferative tips under dynamic culture conditions when compared to static culture (up to 180 vs. 80 µm in height). Additionally, the median mucus layer thickness was significantly increased under flow (50 ± 24 vs. 29 ± 14 µm (static)), with a simultaneous accelerated maturation of the cells into a goblet-like phenotype. We demonstrated the strong impact of culture conditions on the differentiation and reorganization of HT29-MTX cells. The results comprise valuable advances towards the improvement of existing GI and mucus models or the development of novel systems using our newly designed culture chambers.

Influenza A virus (IAV) continuously causes epidemics and claims numerous lives every year. The available treatment options are insufficient and the limited pertinence of animal models for human IAV infections is hampering the development of new therapeutics. Bioprinted tissue models support studying pathogenic mechanisms and pathogen-host interactions in a human micro tissue environment. Here, we describe a human lung model, which consisted of a bioprinted base of primary human lung fibroblasts together with monocytic THP-1 cells, on top of which alveolar epithelial A549 cells were printed. Cells were embedded in a hydrogel consisting of alginate, gelatin and collagen. These constructs were kept in long-term culture for 35 days and their viability, expression of specific cell markers and general rheological parameters were analyzed. When the models were challenged with a combination of the bacterial toxins LPS and ATP, a release of the proinflammatory cytokines IL-1β and IL-8 was observed, confirming that the model can generate an immune response. In virus inhibition assays with the bioprinted lung model, the replication of a seasonal IAV strain was restricted by treatment with an antiviral agent in a dose-dependent manner. The printed lung construct provides an alveolar model to investigate pulmonary pathogenic biology and to support development of new therapeutics not only for IAV, but also for other viruses.

Thermoresponsive coatings that exhibit "switchable" protein- and cell-adhesive properties are frequently used for the fabrication of cell sheets. Among other architectures, polymer brush coatings have shown to be especially viable due to their distinct phase transition behavior, which can be tailored via a manifold of adjustable brush characteristics, such as the (co)monomer composition, polymer chain length, and grafting density. Brush coatings based on poly(glycidyl ether)s (PGEs) have shown to efficiently mediate cell sheet fabrication when tethered to various tissue culture substrates. Herein, we report the phase transition of self-assembled PGE brushes with respect to polymer molecular weight ( M : 10 and 22 kDa) and grafting density (0.07-0.5 chains nm -2 ) on gold model substrates studied by quasi-static QCM-D temperature ramp measurements. The brush grafting density can be tuned via the applied grafting conditions, and all brushes investigated feature broad phase transition regimes (Δ T ∼15 °C) with volume phase transition temperatures (VPTTs) close to the cloud point temperatures (CPTs) of the PGEs in solution. We further demonstrate that brush coatings with a low grafting density (0.07-0.12 chains nm -2 ) exhibit a continuous brush-to-mushroom transition, whereas brushes with medium grafting densities (0.3-0.5 chains nm -2 ) undergo a brush-to-brush transition comprising vertical phase separation during the phase transition progress. These insights help to understand the transition behavior of thin, thermoresponsive brushes prepared via grafting-to strategies and contribute to their rational design for improved functional surfaces.

Anterior cruciate ligament (ACL) cell sheets combined with biomechanically competent scaffolds might facilitate ACL tissue engineering. Since thermoresponsive polymers allow a rapid enzyme-free detachment of cell sheets, we evaluated the applicability of a thermoresponsive poly(glycidyl ether) (PGE) coating for cruciate ligamentocyte sheet formation and its influence on ligamentocyte phenotype during sheet-mediated colonization of embroidered scaffolds. Ligamentocytes were seeded on surfaces either coated with PGE or without coating. Detached ligamentocyte sheets were cultured separately or wrapped around an embroidered scaffold made of polylactide acid (PLA) and poly(lactic-co-ε-caprolactone) (P(LA-CL)) threads functionalized by gas-phase fluorination and with collagen foam. Ligamentocyte viability, protein and gene expression were determined in sheets detached from surfaces with or without PGE coating, scaffolds seeded with sheets from PGE-coated plates and the respective monolayers. Stable and vital ligamentocyte sheets could be produced within 24 h with both surfaces, but more rapidly with PGE coating. PGE did not affect ligamentocyte phenotype. Scaffolds could be colonized with sheets associated with high cell survival, stable gene expression of ligament-related type I collagen, decorin, tenascin C and Mohawk after 14 d and extracellular matrix (ECM) deposition. PGE coating facilitates ligamentocyte sheet formation, and sheets colonizing the scaffolds displayed a ligament-related phenotype.

Islet-based recellularization of decellularized, repurposed rat livers may form a transplantable Neo-Pancreas. The aim of this study is the establishment of the necessary protocols, the evaluation of the organ structure and the analysis of the islet functionality ex vivo. After perfusion-based decellularization of rat livers, matrices were repopulated with endothelial cells and mesenchymal stromal cells, incubated for 8 days in a perfusion chamber, and finally repopulated on day 9 with intact rodent islets. Integrity and quality of re-endothelialization was assessed by histology and FITC-dextran perfusion assay. Functionality of the islets of Langerhans was determined on day 10 and day 12 via glucose stimulated insulin secretion. Blood gas analysis variables confirmed the stability of the perfusion cultivation. Histological staining showed that cells formed a monolayer inside the intact vascular structure. These findings were confirmed by electron microscopy. Islets infused via the bile duct could histologically be found in the parenchymal space. Adequate insulin secretion after glucose stimulation after 1-day and 3-day cultivation verified islet viability and functionality after the repopulation process. We provide the first proof-of-concept for the functionality of islets of Langerhans engrafted in a decellularized rat liver. Furthermore, a re-endothelialization step was implemented to provide implantability. This technique can serve as a bioengineered platform to generate implantable and functional endocrine Neo-Pancreases., Competing Interests: Declaration of Competing Interest The authors have no conflicts of interest to declare., (Copyright © 2020. Published by Elsevier Ltd.)

The production of biomaterials that endow significant morphogenic and microenvironmental cues for the constitution of cell integration and regeneration remains a key challenge in the successful implementation of functional organ replacements. Despite the vast development in the production of biological and architecturally native matrices, the complex compositions and pivotal figures by which the human matrisome mediates many of its essential functions are yet to be defined. Here we present a thorough analysis of the native human liver proteomic landscape using decellularization and defatting protocols to create extracellular matrix scaffolds of natural origin that can further be used in both bottom-up and top-down approaches in tissue engineering based organ replacements. Furthermore, by analyzing human liver extracellular matrices in different stages of fibrosis and cirrhosis, we have identified distinct attributes of these tissues that could potentially be exploited therapeutically and thus require further investigation. The general experimental pipeline presented in this study is applicable to any type of tissue and can be widely used for different approaches in regenerative medicine and in the construction of novel biomaterials for organ engineering approaches., (Copyright © 2020 Elsevier Ltd. All rights reserved.)

Thermoresponsive poly(glycidyl ether) brushes can be grafted to applied tissue culture substrates and used for the fabrication of primary human cell sheets. The self-assembly of such brushes is achieved via the directed physical adsorption and subsequent UV immobilization of block copolymers equipped with a short, photo-reactive benzophenone-based anchor block. Depending on the chemistry and hydrophobicity of the benzophenone anchor, we demonstrate that such block copolymers exhibit distinct thermoresponsive properties and aggregation behaviors in water. Independent on the block copolymer composition, we developed a versatile grafting-to process which allows the fabrication of poly(glycidyl ether) brushes on various tissue culture substrates from dilute aqueous-ethanolic solution. The viability of this process crucially depends on the chemistry and hydrophobicity of, both, benzophenone-based anchor block and substrate material. Utilizing these insights, we were able to manufacture thermoresponsive poly(glycidyl ether) brushes on moderately hydrophobic polystyrene and polycarbonate as well as on rather hydrophilic polyethylene terephthalate and tissue culture-treated polystyrene substrates. We further show that the temperature-dependent switchability of the brush coatings is not only dependent on the cloud point temperature of the block copolymers, but also markedly governed by the hydrophobicity of the surface-bound benzophenone anchor and the subjacent substrate material. Our findings demonstrate that the design of amphiphilic thermoresponsive block copolymers is crucial for their phase transition characteristics in solution and on surfaces.

Gelatin methacryloyl (GelMA) is a chemically modified extracellular matrix (ECM)-derived biopolymer that is widely used for 3D fabrication of tissue engineering scaffolds. However, its tendency for physical gelation limits its use in aqueous 3D printing resins to low concentrations, yielding a poor printing resolution in stereolithography (SLA). To obtain a GelMA-based resin that can be printed into high-resolution tissue scaffolds, we formulated resins of fish and porcine-derived GelMA in formamide using GelMA alone or mixed with star-shaped poly(ε-caprolactone) methacrylate (PCL-MA). We identified GelMA resins and GelMA/PCL-MA hybrid resins with a ratio of 70/30 wt-% to yield a suitable viscosity for SLA at 32 °C and demonstrated the resolution of the new resins in SLA by 3D printing acellular human small intestine-mimicking tissue scaffolds. The presence of PCL-MA in the hybrid resins improved the 3D printing fidelity compared to the neat GelMA resins, while GelMA provided the hybrid materials with enhanced swelling and proliferation of seeded cells. We further demonstrated the transferability of our resin formulation to native organ-derived materials by successfully replacing GelMA in the hybrid resin with solubilized, methacryloyl-functionalized decellularized liver ECM (dECM-MA) and by 3D printing multi-layer dECM/PCL-MA hydrogels., Competing Interests: Declaration of competing interest A European patent application entitled “Photocurable composition” (European patent office, 19189493.0) by Laura Elomaa and Marie Weinhart was submitted on 31.07.2019 based on the results in the current manuscript. The authors declare no other conflicts of interest., (Copyright © 2020 Elsevier B.V. All rights reserved.)

A complex of an N-heterocyclic carbene I t Bu (1,3-di-tert-butylimidazolin-2-ylidene) and aluminum hydride was observed to isomerize into an abnormal carbene complex aI t Bu·AlH 3 (aI t Bu = 1,3-di-tert-butylimidazolin-4-ylidene) in a polar solvent, and, for the first time, in the solid state. I t Bu·AlH 3 and aI t Bu·AlH 3 were structurally characterized by single crystal X-ray diffraction analysis. NMR studies and DFT computations indicate that the polarity of the solvent promotes the isomerization process. The possible pathways for the isomerization are discussed on the basis of the DFT computational studies.

Three-dimensional tissue cultures are important models for the study of cell-cell and cell-matrix interactions, as well as, to investigate tissue repair and reconstruction pathways. Therefore, we designed a reproducible and easy to handle printable bioreactor system (Teburu), that is applicable for different approaches of pathway investigation and targeted tissue repair using human tissue slices as a three-dimensional cell culture model. Here, we definitively describe Teburu as a controlled environment to reseed a 500-µm thick decellularized human liver slice using human mesenchymal stroma cells. During a cultivation period of eight days, Teburu, as a semi-open and low consumption system, was capable to maintain steady pH and oxygenation levels. Its combination with additional modules delivers an applicability for a wide range of tissue engineering approaches under optimal culture conditions., (© 2019 International Center for Artificial Organs and Transplantation and Wiley Periodicals, Inc.)

3D organ models have gained increasing attention as novel preclinical test systems and alternatives to animal testing. Over the years, many excellent in vitro tissue models have been developed. In parallel, microfluidic organ-on-a-chip tissue cultures have gained increasing interest for their ability to house several organ models on a single device and interlink these within a human-like environment. In contrast to these advancements, the development of human disease models is still in its infancy. Although major advances have recently been made, efforts still need to be intensified. Human disease models have proven valuable for their ability to closely mimic disease patterns in vitro, permitting the study of pathophysiological features and new treatment options. Although animal studies remain the gold standard for preclinical testing, they have major drawbacks such as high cost and ongoing controversy over their predictive value for several human conditions. Moreover, there is growing political and social pressure to develop alternatives to animal models, clearly promoting the search for valid, cost-efficient and easy-to-handle systems lacking interspecies-related differences. In this review, we discuss the current state of the art regarding 3D organ as well as the opportunities, limitations and future implications of their use., (Copyright © 2018 Elsevier Ltd. All rights reserved.)

Thermoresponsive brushes based on linear poly(glycidyl ether)s (PGEs) have already shown to be functional coatings for cell sheet fabrication. In here, we introduce a method to functionalize polystyrene (PS) tissue culture substrates with thermoresponsive coatings comprising glycidyl ether-based bottlebrush architectures. Utilizing the UV-induced "grafting-from" approach, thermoresponsive oligo(glycidyl ether) acrylate (OGEA) macromonomers were polymerized from PS substrates under bulk conditions. Applying ellipsometry, water contact angle (CA), and atomic force microscopy (AFM) measurements, we found that OGEA coatings exhibit a complex, gel-like structure comprising nanosized roughness and exhibit a temperature-dependent phase transition in water through the reversible hydration of OGEA bottlebrush side chains. To assess the utility of the coatings as functional substrates for cell sheet fabrication, human dermal fibroblast (HDF) adhesion and detachment were investigated. By adjusting the bottlebrush properties via the grafting procedure and coating structure, we were able to harvest confluent HDF sheets from functionalized PS substrates in a temperature-triggered, controlled manner. As the first report on surface-grafted bottlebrushes comprising thermoresponsive side chains with molecular weight of up to 1 kDa, this study demonstrates the potential of OGEA-based coatings for cell sheet fabrication.

In this study, we introduce a platform to fabricate human dermal fibroblast (HDF), human aortic smooth muscle cell (HAoSMC) and human umbilical vein endothelial cell (HUVEC) sheets using thermoresponsive poly(glycidyl ether) coatings. Copolymer brushes based on glycidyl methyl ether (GME) and ethyl glycidyl ether (EGE) were self-assembled onto polystyrene (PS) culture substrates via the physical adsorption of a hydrophobic, photoreactive benzophenone anchor block based on the monomer 4-[2-(2,3-epoxypropoxy)ethoxy]benzophenone (EEBP). The directed self-assembly of well-defined, end-tethered poly(GME-ran-EGE)-block-poly(EEBP) (PGE) brushes was achieved via the selective, EEBP-driven adsorption of the asymmetric block copolymer from dilute aqueous solution below its cloud point temperature (CPT). Subsequently, the PGE brush layers were covalently immobilized onto the PS surfaces by irradiation with UV light and characterized by ellipsometry, static water contact angle (CA) measurements and atomic force microscopy (AFM). We found that, by decreasing the temperature from 37 to 20 °C, the coatings undergo a pancake-to-brush transition, which triggers cell sheet detachment. In addition, cell culture parameters were optimized to allow proper adhesion and controlled detachment of confluent HDF, HAoSMC and HUVEC sheets, which can be applied in vascular tissue engineering.

Bioprinting is a novel technology that may help to overcome limitations associated with two-dimensional (2D) cell cultures and animal experiments, as it allows the production of three-dimensional (3D) tissue models composed of human cells. The present study describes the optimization of a bioink composed of alginate, gelatin and human extracellular matrix (hECM) to print human HepaRG liver cells with a pneumatic extrusion printer. The resulting tissue model was tested for its suitability for the study of transduction by an adeno-associated virus (AAV) vector and infection with human adenovirus 5 (hAdV5). We found supplementation of the basic alginate/gelatin bioink with 0.5 and 1 mg/mL hECM provides desirable properties for the printing process, the stability of the printed constructs, and the viability and metabolic functions of the printed HepaRG cells. The tissue models were efficiently transduced by AAV vectors of serotype 6, which successfully silenced an endogenous target (cyclophilin B) by means of RNA interference. Furthermore, the printed 3D model supported efficient adenoviral replication making it suitable to study virus biology and develop new antiviral compounds. We consider the approach described here paradigmatic for the development of 3D tissue models for studies including viral vectors and infectious viruses.

Bioprinting is a new technology, which arranges cells with high spatial resolution, but its potential to create models for viral infection studies has not yet been fully realized. The present study describes the optimization of a bioink composition for extrusion printing. The bioinks were biophysically characterized by rheological and electron micrographic measurements. Hydrogels consisting of alginate, gelatin and Matrigel were used to provide a scaffold for a 3D arrangement of human alveolar A549 cells. A blend containing 20% Matrigel provided the optimal conditions for spatial distribution and viability of the printed cells. Infection of the 3D model with a seasonal influenza A strain resulted in widespread distribution of the virus and a clustered infection pattern that is also observed in the natural lung but not in two-dimensional (2D) cell culture, which demonstrates the advantage of 3D printed constructs over conventional culture conditions. The bioink supported viral replication and proinflammatory interferon release of the infected cells. We consider our strategy to be paradigmatic for the generation of humanized 3D tissue models by bioprinting to study infections and develop new antiviral strategies.

Thermoresponsive polymer coatings can facilitate cell sheet fabrication under mild conditions by promoting cell adhesion and proliferation at 37 °C. At lower temperatures the detachment of confluent cell sheets is triggered without enzymatic treatment. Thus, confluent cell sheets with intact extracellular matrix for regenerative medicine or tissue engineering applications become available. Herein, we applied the previously identified structural design parameters of functional, thermoresponsive poly(glycidyl ether) brushes on gold to the more application-relevant substrate glass via the self-assembly of a corresponding block copolymer (PGE-AA) with a short surface-reactive, amine-presenting anchor block. Both, physical and covalent immobilization on glass via either multivalent ionic interactions of the anchor block with bare glass or the coupling of the anchor block to a polydopamine (PDA) adhesion layer on glass resulted in stable coatings. Atomic force microscopy revealed a high degree of roughness of covalently attached coatings on the PDA adhesion layer, while physically attached coatings on bare glass were smooth and in the brush-like regime. Cell sheets of primary human dermal fibroblasts detached reliably (86%) and within 20 ± 10 min from physically tethered PGE-AA coatings on glass when prepared under cloud point grafting conditions. The presence of the laterally inhomogeneous PDA adhesion layer, however, hindered the spontaneous temperature-triggered cell detachment from covalently grafted PGE-AA, decreasing both detachment rate and reliability. Despite being only physically attached, self-assembled monolayer brushes of PGE-AA block copolymers on glass are functional and stable thermoresponsive coatings for application in cell sheet fabrication of human fibroblasts as determined by X-ray photoelectron spectroscopy.

Platelets have a limited shelf life, due to the risk of bacterial contamination and platelet quality loss. Most platelet storage bags are made of a mixture of polyvinyl chloride with a plasticizer, denoted as pPVC. To improve biocompatibility of pPVC with platelets and to inhibit bacterial biofilm formation, an antifouling polymer coating is developed using mussel-inspired chemistry. A copolymer of N,N-dimethylacrylamide and N-(3-aminopropyl)methacrylamide hydrochloride is synthesized and coupled with catechol groups, named DA51-cat. Under mild aqueous conditions, pPVC is first equilibrated with an anchoring polydopamine layer, followed by a DA51-cat layer. Measurements show this coating decreases fibrinogen adsorption to 5% of the control surfaces. One-step coating with DA51-cat does not coat pPVC efficiently although it is sufficient for coating silicon wafers and gold substrates. The dual layer coating on platelet bags resists bacterial biofilm formation and considerably decreases platelet adhesion. A cationic antimicrobial peptide, E6, is conjugated to DA51-cat then coated on silicon wafers and introduces bactericidal activity to these surfaces. Time-of-flight second ion-mass spectroscopy is successfully applied to characterize these surfaces. pPVC is widely used in medical devices; this method provides an approach to controlling biofouling and bacterial growth on it without elaborate surface modification procedures., (© 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

The fabrication of cell sheets is a major requirement for bottom-up tissue engineering purposes (e.g., cell sheet engineering) and regenerative medicine. Employing thermoresponsive polymer coatings as tissue culture substrates allows for the mild, temperature-triggered detachment of intact cell sheets along with their extracellular matrix (ECM). It has been shown before that biocompatible, thermoresponsive poly(glycidyl ether) monolayers on gold substrates can be utilized to harvest confluent cell sheets by simply reducing the temperature to 20 °C. Herein, we report on the first poly(glycidyl ether)-based coating on an application-relevant tissue culture plastic substrate. We devised a simple, substrate-geometry-independent method to functionalize polystyrene (PS) surfaces from dilute ethanolic solution via the physical adsorption process of a thermoresponsive poly(glycidyl ether) block copolymer (PGE) bearing a short, hydrophobic, and photoreactive benzophenone (BP) anchor block. Subsequently, the PGE-coated PS is UV-irradiated for covalent photoimmobilization of the polymer on the PS substrate. Online monitoring of the adsorption process via QCM-D measurements and detailed characterization of the resulting coatings via AFM, ellipsometry, and water contact angle (CA) measurements revealed the formation of an ultrathin PGE layer with an average dry thickness of 0.7 ± 0.1 nm. Adhesion and proliferation of human dermal fibroblasts on PGE-coated PS and tissue culture PS (TCPS) were comparable. For temperature-triggered detachment, fibroblasts were cultured in PGE-coated PS culture dishes at 37 °C for 24 h until they reached confluency. Intact cell sheets could be harvested from the thermoresponsive substrates within 51 ± 17 min upon cooling to 20 °C, whereas sheets could not be harvested from uncoated PS and TCPS control dishes. Live/dead staining and flow cytometry affirmed a high viability of the fibroblasts within the cell sheets. Hence, ultrathin layers of thermoresponsive poly(glycidyl ether)s on hydrophobic PS substrates are functional coatings for cell sheet fabrication.

Thermoresponsive polymer coatings, optimized for cell adhesion and thermally-triggered cell detachment, allow the fabrication of confluent cell sheets with intact extracellular matrix. However, rational design guidelines for such coatings are rare, since temperature-triggered cell adhesion and detachment from thermoresponsive surfaces are mechanistically not well understood. Herein, we investigated the impact of molecular weight (2, 9, 24kDa), grafting density (0.04-1.4 chains nm -2 ), morphology, and roughness of well-characterized thermoresponsive poly(glycidyl ether) brushes on the cell response at 37 and 20°C. NIH 3T3 mouse fibroblasts served as a model cell line for adhesion, proliferation, and cell sheet detachment. The cell response was correlated with serum protein adsorption from cell culture medium containing 10% fetal bovine serum. Intact cell sheets could be harvested from all the studied poly(glycidyl ether) coated surfaces, irrespective of the molecular weight, provided that the morphology of the coating was homogenous and the surface was fully shielded by the hydrated brush. The degree of chain overlap was estimated by the ratio of twice the polymer's Flory radius in a theta solvent to its interchain distance, which should be located in the strongly overlapping brush regime (2 R f /l>1.4). In contrast, dense PNIPAM (2.5kDa) control monolayers did not induce protein adsorption from cell culture medium at 37°C and, as a result, did not allow a significant cell adhesion. These structural design parameters of functional poly(glycidyl ether) coatings on gold will contribute to future engineering of these thermoresponsive coatings on more common, cell culture relevant substrates., Statement of Significance: Cell sheet engineering as a scaffold-free approach towards tissue engineering resembles a milestone in regenerative medicine. The fabrication of confluent cell sheets maintains the extracellular matrix of cells which serves as the physiological cell scaffold. Thermoresponsive poly(glycidyl ether)s are highly cell-compatible and brushes thereof promote cell adhesion and growth without modification with additional cell adhesive ligands. Thus, a direct correlation of temperature-dependent serum protein adsorption and cell response with surface design parameters such as grafting density and molecular weight became accessible. Hence, surface engineering parameters of well-defined poly(glycidyl ether) monolayers for reproducible cell sheet fabrication have been identified. These design guidelines may also prove beneficial in the development of other brush-like thermoresponsive coatings for cell sheet engineering., (Copyright © 2017 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.)

N-Heterocyclic carbene adducts of the parent arsinidene (AsH) were prepared by two different synthetic routes, either by reaction of As(SiMe 3 ) 3 with 2,2-difluoroimidazolines followed by desilylation or by reaction of [Na(dioxane) 3.31 ][AsCO] with imidazolium chlorides.

For a meaningful correlation of surface coatings with their respective biological response reproducible coating procedures, well-defined surface coatings, and thorough surface characterization with respect to layer thickness and grafting density are indispensable. The same applies to polymeric monolayer coatings which are intended to be used for, e.g., fundamental studies on the volume phase transition of surface end-tethered thermoresponsive polymer chains. Planar gold surfaces are frequently used as model substrates, since they allow a variety of straightforward surface characterization methods. Herein we present reproducible grafting-to procedures performed with thermoresponsive poly(glycidyl ether) copolymers composed of glycidyl methyl ether (GME) and ethyl glycidyl ether (EGE). The copolymers feature different molecular weights (2 kDa, 9 kDa, 24 kDa) and are equipped with varying sulfur-containing anchor groups in order to achieve adjustable grafting densities on gold surfaces and hence control the tethered polymers' chain conformation. We determined "wet" and "dry" thicknesses of these coatings by QCM-D and ellipsometry measurements and deduced anchor distances and degrees of chain overlap of the polymer chains assembled on gold. Grafting under cloud point conditions allowed for higher degrees of chain overlap compared to grafting from a good solvent like ethanol, independent of the used sulfur-containing anchor group for polymers with low (2 kDa) and medium (9 kDa) molecular weights. By contrast, the achieved grafting densities and thus chain overlaps of surface-tethered polymers with high (24 kDa) molecular weights were identical for both grafting methods. Monolayers prepared from an ethanolic solution of poly(glycidyl ether)s equipped with sterically demanding disulfide-containing anchors revealed the lowest degrees of chain overlap. The ratio of the radius of gyration to the anchor distance (2 R g /l) of the latter coating was found to be lower than 1.4, indicating that the assembly was rather in the mushroom-like than in the brush regime. Polymer chains with thiol-containing anchors of different alkyl chain lengths (C 11 SH vs C 4 SH) formed assemblies with comparable degrees of chain overlap with 2 R g /l values above 1.4 and are thus in the brush regime. Molecular weights influenced the achievable degree of chain overlap on the surface. Coatings prepared with the medium molecular weight polymer (9 kDa) resulted in the highest chain packing density. Control of grafting density and thus chain overlap in different regimes (brush vs mushroom) on planar gold substrates are attainable for monolayer coatings with poly(GME-ran-EGE) by adjusting the polymer's molecular weight and anchor group as well as the conditions for the grafting-to procedure.

A library of hyperbranched polyglycerols (HPGs) functionalized with different mole fractions of zwitterionic sulfabetaine and cationic quaternary ammonium ligands was synthesized and characterized. A post-polymerization method was employed that utilized double bond moieties on the dendritic HPG for the coupling of thiol-terminated ligands via UV initiated thiol-ene "click" chemistry. The proportions of different ligands were precisely controlled by varying the ligand concentration during the irradiation process. The effect of the polymer library on hemostasis was investigated using whole human blood. It was found that polymer with ≥40% of alkenes converted to positive charges and the remainder to sulfabetaines caused hemagglutination at ≥1 mg/mL, without causing red blood cell lysis. The quaternary ammonium groups can interact with the negative charged sites on the membranes of erythrocytes, which provides the bioadhesion. The zwitterionic sulfabetaine evidently provides a hydration layer to partially mask the adverse effects that are likely to be caused by cationic moieties. The polymer was also found able to enhance platelet aggregation and activation in a concentration and positive charge density-dependent manner, which would contribute to initiating hemostasis. In a variety of other assays the material was found to be largely biocompatible. The polymer-induced hemostasis is obtained by a process independent of the normal blood clotting cascade but dependent on red blood cell agglutination, where the polymers promote hemostasis by linking erythrocytes together to form a lattice to entrap the cells., (Copyright © 2016 Elsevier Ltd. All rights reserved.)

In droplet-based microfluidics, non-ionic, high-molecular weight surfactants are required to stabilize droplet interfaces. One of the most common structures that imparts stability as well as biocompatibility to water-in-oil droplets is a triblock copolymer surfactant composed of perfluoropolyether (PFPE) and polyethylene glycol (PEG) blocks. However, the fast growing applications of microdroplets in biology would benefit from a larger choice of specialized surfactants. PEG as a hydrophilic moiety, however, is a very limited tool in surfactant modification as one can only vary the molecular weight and chain-end functionalization. In contrast, linear polyglycerol offers further side-chain functionalization to create custom-tailored, biocompatible droplet interfaces. Herein, we describe the synthesis and characterization of polyglycerol-based triblock surfactants with tailored side-chain composition, and exemplify their application in cell encapsulation and in vitro gene expression studies in droplet-based microfluidics.

Scaffold-free cell sheet engineering using thermoresponsive substrates provides a promising alternative to conventional tissue engineering which in general employs biodegradable scaffold materials. We have previously developed a thermoresponsive coating with glycerol based linear copolymers that enables gentle harvesting of entire cell sheets. In this article we present an in-depth analysis of these thermoresponsive linear polyglycidyl ethers and their performance as coating for substrates in cell culture in comparison with commercially available poly(N-isopropylacrylamide) (PNIPAM) coated culture dishes. A series of copolymers of glycidyl methyl ether (GME) and glycidyl ethyl ether (EGE) was prepared in order to study their thermoresponsive properties in solution and on the surface with respect to the comonomer ratio. In both cases, when grafted to planar surfaces or spherical nanoparticles, the applied thermoresponsive polyglycerol coatings render the respective surfaces switchable. Protein adsorption experiments on copolymer coated planar surfaces with surface plasmon resonance (SPR) spectroscopy reveal the ability of the tested thermoresponsive coatings to be switched between highly protein resistant and adsorptive states. Cell culture experiments demonstrate that these thermoresponsive coatings allow for adhesion and proliferation of NIH 3T3 fibroblasts comparable to TCPS and faster than on PNIPAM substrates. Temperature triggered detachment of complete cell sheets from copolymer coated substrates was accomplished within minutes while maintaining high viability of the harvested cells. Thus such glycerol based copolymers present a promising alternative to PNIPAM as a thermoresponsive coating of cell culture substrates., (Copyright © 2015 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.)

Hyperactivity of microglia and loss of functional circuitry is a common feature of many neurological disorders including those induced or exacerbated by inflammation. Herein, we investigate the response of microglia and changes in hippocampal dendritic postsynaptic spines by dendritic polyglycerol sulfate (dPGS) treatment. Mouse microglia and organotypic hippocampal slices were exposed to dPGS and an inflammogen (lipopolysaccharides). Measurements of intracellular fluorescence and confocal microscopic analyses revealed that dPGS is avidly internalized by microglia but not CA1 pyramidal neurons. Concentration and time-dependent response studies consistently showed no obvious toxicity of dPGS. The adverse effects induced by proinflammogen LPS exposure were reduced and dendritic spine morphology was normalized with the addition of dPGS. This was accompanied by a significant reduction in nitrite and proinflammatory cytokines (TNF-α and IL-6) from hyperactive microglia suggesting normalized circuitry function with dPGS treatment. Collectively, these results suggest that dPGS acts anti-inflammatory, inhibits inflammation-induced degenerative changes in microglia phenotype and rescues dendritic spine morphology.

Heparin-based anticoagulant drugs have been widely used for the prevention of blood clotting during surgical procedures and for the treatment of thromboembolic events. However, bleeding risks associated with these anticoagulants demand continuous monitoring and neutralization with suitable antidotes. Protamine, the only clinically approved antidote to heparin, has shown adverse effects and ineffectiveness against low-molecular weight heparins and fondaparinux, a heparin-related medication. Alternative approaches based on cationic molecules and recombinant proteins have several drawbacks including limited efficacy, toxicity, immunogenicity, and high cost. Thus, there is an unmet clinical need for safer, rapid, predictable, and cost-effective anticoagulant-reversal agents for all clinically used heparins. We report a design strategy for a fully synthetic dendritic polymer-based universal heparin reversal agent (UHRA) that makes use of multivalent presentation of branched cationic heparin binding groups (HBGs). Optimization of the UHRA design was aided by isothermal titration calorimetry studies, biocompatibility evaluation, and heparin neutralization analysis. By controlling the scaffold's molecular weight, the nature of the protective shell, and the presentation of HBGs on the polymer scaffold, we arrived at lead UHRA molecules that completely neutralized the activity of all clinically used heparins. The optimized UHRA molecules demonstrated superior efficacy and safety profiles and mitigated heparin-induced bleeding in animal models. This new polymer therapeutic may benefit patients undergoing high-risk surgical procedures and has potential for the treatment of anticoagulant-related bleeding problems., (Copyright © 2014, American Association for the Advancement of Science.)

Objective: To investigate the role of adhesion molecules in C protein-induced myositis (CIM), a murine model of polymyositis (PM)., Methods: CIM was induced in wild-type mice, L-selectin-deficient (L-selectin(-/-) ) mice, intercellular adhesion molecule 1 (ICAM-1)-deficient (ICAM-1(-/-) ) mice, and mice deficient in both L-selectin and ICAM-1 (L-selectin(-/-) ICAM-1(-/-) mice). Myositis severity, inflammatory cell infiltration, and messenger RNA expression in the inflamed muscles were analyzed. The effect of dendritic polyglycerol sulfate, a synthetic inhibitor that suppresses the function of L-selectin and endothelial P-selectin, was also examined., Results: L-selectin(-/-) mice and L-selectin(-/-) ICAM-1(-/-) mice developed significantly less severe myositis compared to wild-type mice, while ICAM-1 deficiency did not inhibit the development of myositis. L-selectin(-/-) mice that received wild-type T cells developed myositis. Treatment with dendritic polyglycerol sulfate significantly diminished the severity of myositis in wild-type mice compared to treatment with control., Conclusion: These data indicate that L-selectin plays a major role in the development of CIM, whereas ICAM-1 plays a lesser role, if any, in the development of CIM. L-selectin-targeted therapy may be a candidate for the treatment of PM., (Copyright © 2014 by the American College of Rheumatology.)