Search

The rheological behavior of concrete pumping in the bend section is complex. The existing conversion calculation for pumping pressure loss based on the straight pipe section often fails to meet engineering precision requirements. This paper develops a pressure loss correction model for a concrete pumping bend section based on a new one-dimensional flow model for the straight pipe section simulation of particle flow; the study analyzes the impact of parameters such as elbow shape and pumping flow rate on pressure loss. An equivalent conversion relationship between the bend section and the straight section is established. The comparison with the measured pressure values from the project shows that the relative error between the pressure loss values calculated by the correction model and the actual measurements is 15.8%. [ABSTRACT FROM AUTHOR]

The stability and Hopf bifurcation of a class of flywheel governor systems subject to stochastic excitation under time-delay feedback are studied. The model is simplified using center manifold reduction to obtain a paradigm for a two-dimensional central subsystem. The system converges asymptotically to an Itô stochastic differential equation based on polar transformations and stochastic averaging method. The stochastic stability of the system is analyzed by applying the maximum Lyapunov exponent and the singular boundary theory, and its probability density function is calculated. In addition, it is found through Monte Carlo numerical simulations that the effects of noise intensity and time-delay on the stochastic P-bifurcation of the system are opposite, and proper noise intensity makes the flywheel governor system converge to the equilibrium position, while a large time-delay leads to stochastic bifurcation and makes the flywheel governor system unstable. Finally, the two-parameter bifurcation diagram is used to further analyze the impact of time-delay and noise intensity on the bifurcation of the system under variable load torque. It is found that the influence of noise intensity and time-delay on the periodic oscillation state is the same, and the stability of the flywheel governor system will decrease with both of their increases. This also further demonstrates the duality of the impact of noise intensity on the same system under different conditions. The above research provides better theoretical references for the design and safe operation of speed control systems. [ABSTRACT FROM AUTHOR]

In this paper, a wind turbine generator drive system with stochastic excitation under both displacement and velocity delayed feedback is considered. Firstly, the center manifold method is used to approximate the delay term of the system, so that the Itô-stochastic differential equation can be obtained by random average method. Through the maximal Lyapunov exponential method, the local stochastic stability and random D-bifurcation conditions of the system are obtained. Secondly, it is verified that the increase of noise intensity and delay value induces the occurrence of random P-bifurcation of the system through Monte Carlo numerical simulations. In addition, the theoretical chaos threshold of the system is derived by the random Melnikov method. The results show that the chaos threshold decreases as the noise intensity increases, and the increase in time delay leads to a delay in the chaotic behavior of the system. Finally, the correctness and effectiveness of the chaos-theoretic analysis are verified based on the one-parameter bifurcation diagrams and the two-parameter bifurcation diagrams. [ABSTRACT FROM AUTHOR]

This paper analyzes the power-cycling capability of insulated-gate bipolar transistor (IGBT) modules in a conventional matrix converter used as a motor drive. The analysis is made under various conditions for this topology, including low-speed-operation capability, high-speed thermal- and power-cycling capabilities, etc. It was found that the power-cycling mean time to failure of IGBT in a matrix converter is low when the input and output frequencies are close to each other or when the output frequency of the converter is low. As a result, the chip size of the conventional matrix converter may be larger than the other candidates. In the end of this paper, some guidance for designing a matrix converter for long-term reliabilities is also discussed. Index Terms--Conventional matrix converter, mean time to failure (MTTF), power cycle, thermal cycle.

Multipulse rectifier system has been shown to be a cost-effective harmonic solution in many industries where IEEE 519 is specified. However, it is susceptible to poor quality of the input source of the power distribution system where the phase unbalance of the source voltage and preexisting low-order harmonic voltages are presented. A small amount of voltage unbalance with preexisting harmonics can create large amount of current harmonics to the input source. Consequently, a stricter preexisting voltage total harmonic distortion condition has to be specified for an 18-pulse rectifier to meet the IEEE 519 current-harmonics requirement. This paper introduces a dc link passive filtering method to solve this problem. It greatly reduces the current harmonics created by the phase unbalance, the fifth-, and the seventh-order voltage harmonics by adding several series LC resonant loops into the dc link. As a result, the proposed 18-pulse rectifier can meet IEEE 519 under several abnormal source voltage conditions of the ac line. Theory analysis, simulation, and experimental result are provided in this paper to verify the effectiveness of this method. Index Terms--IEEE 519, passive filtering, unbalance control, 18-pulse rectifier.