Search

To investigate the flow characteristics of sieve tray columns with circular downcomers, the Euler–Euler gas–liquid two‐phase flow model is used to simulate a three‐dimensional sieve tray column. Each phase is regarded as an interpenetrating continuum with independent transport equations. The velocity distribution, clear liquid height, and foam layer height are predicted by the model. The correlation is established for predicting the clear liquid height on the sieve tray. The results show the following: (1) The sensitivity of the clear liquid height to the gas phase load is greater than that of the liquid phase load. (2) When the gas–liquid distribution is stable, the flow on the round sieve tray column presents a piston flow pattern. (3) The average liquid holdup of the circular downcomer of the three heights all showed a slow decrease at first, and then an inflection point appeared near the height of 0.02 m, after which the liquid holdup dropped sharply. (4) The established correlation has good predictive performance for calculating the clear liquid height in the column, and the relative error between the calculated value and the actual value is less than 10%. [ABSTRACT FROM AUTHOR]

This study investigates the potential of using sewage sludge and low-rank coal for the sustainable production of sulfuric acid, which can then be used for the hydrolysis of straw through ASPEN PLUS simulation. Pyrolysis and gasification processes were used to convert sewage sludge and low-rank coal into syngas, which were then purified and oxidized to produce H2SO4 and NH3 gas. The pyro-gasification enhanced syngas yield. The effects of key process parameters such as temperature, steam-to-biomass ratio, equivalence ratio, and feedstock composition on the yield and composition of syngas and H2SO4 coupled with minor parameters like pressure were investigated. The simulation was conducted over the temperature and pressure range of 400 – 900°°C and 70 – 150 kPa respectively. While the steam-to-biomass ratio and equivalence ratio were respectively varied from 0.66 – 1.65 and 0.14 – 0.35. Part of the 1012.88 kg/h of H2SO4 produced was used to hydrolyze straw, producing glucose as a valuable feedstock for biorefineries. About 3989.10 kg/h of NH3 was produced. Results showed that the use of sewage sludge and low-rank coal as feedstocks for syngas production can be a sustainable and cost-effective alternative to traditional fossil fuels. The resulting H2SO4 can also be used for various other applications, such as in the production of fertilizers and detergents. Overall, this study agrees with the literature, demonstrates the potential of integrating biomass and waste resources for the sustainable production of high-value chemicals and fuels, and contributes to the field of sustainable chemical and energy production while addressing environmental and economic considerations. [ABSTRACT FROM AUTHOR]

Presently, selective catalytic reduction (SCR), with either carbon monoxide, urea, hydrocarbons, hydrogen, or ammonia as a reductant, has become a nitrogen oxide (NOx) removal technology (NOx conversion) of many catalytic companies and diesel engine exhaust gas. Although, there exists a serious threat of low-temperature limitations. So far, certain scientists have shown that barium-based (Ba-based) catalysts have the potential to be highly effective at SCR of NOx at low temperatures when ammonia is used as the reducing agent. The process of NOx storage and reduction which alternate SCR is known as the Lean NOx trap. Herein, we give the condensed advancements and production of the catalysts that involve BaO in low-temperature NH3-SCR of NOx, the advantages of BaO catalysts compared to the recently hot electrocatalysis, the stability of BaO catalyst materials, and the condensed advancements and production of the catalysts that involve BaO in low-temperature NH3-SCR of NOx. These catalysts are viewed in the light of their preparation method, particulate, and posture in mixed oxides. Also, the characteristic features of Ba-based catalysts are carefully considered and briefed under the following areas: preparation method and precursor, crystallinity, calcination temperature, morphology, acid sites, the specific surface area for reaction, redox property, and activation energy of catalysts. More to these are the discussions on Eley–Rideal [E-R] and Langmuir–Hinshelwood [L–H] mechanisms, the H2O/SO2 and O2 permissiveness, and the NH3-SCR reaction mechanism over Ba-based catalysts highlighting their possible effects. Finally, we proposed the prospect and the likely future research plan for the low-temperature NH3-SCR of NOx. [ABSTRACT FROM AUTHOR]

Selective catalytic reduction (SCR) is now an established NOx removal technology for industrial flue gas as well as for diesel engine exhaust gas. However, it is still a big challenge to develop a novel low-temperature catalyst for NH3-SCR of NOx, especially at a temperature below 200°C. In the past few years, many studies have demonstrated the potential of iron (Fe)-based catalysts as low-temperature catalysts for NH3-SCR of NOx. Herein, we summarize the recent progress and performance of Fe-based catalysts for low-temperature NH3-SCR of NOx. Catalysts are divided into three categories: single FexOy, Fe-based multimetal oxide, and Fe-based multimetal oxide with support catalysts. The catalytic activity and selectivity of Fe-based catalysts are systematically analyzed and summarized in light of some key factors such as activation energy, specific surface area, morphology, crystallinity, preparation method and precursor, acid sites, calcination temperature, other metal dopant/substitute, and redox property of catalysts. In addition, H2O/SO2 tolerance and the NH3-SCR reaction mechanism over Fe-based catalysts, including Eley-Rideal and Langmuir-Hinshelwood mechanism, are emphasized. Lastly, the perspectives and future research directions of low-temperature NH3-SCR of NOx are also proposed. [ABSTRACT FROM AUTHOR]

Selective catalytic reduction (SCR) is now an established NOx removal technology for industrial flue gas as well as for diesel engine exhaust gas. However, it is still a big challenge to develop a novel low-temperature catalyst for NH3-SCR of NOx, especially at a temperature below 200°C. In the past few years, many studies have demonstrated the potential of iron (Fe)-based catalysts as low-temperature catalysts for NH3-SCR of NOx. Herein, we summarize the recent progress and performance of Fe-based catalysts for low-temperature NH3-SCR of NOx. Catalysts are divided into three categories: single FexOy, Fe-based multimetal oxide, and Fe-based multimetal oxide with support catalysts. The catalytic activity and selectivity of Fe-based catalysts are systematically analyzed and summarized in light of some key factors such as activation energy, specific surface area, morphology, crystallinity, preparation method and precursor, acid sites, calcination temperature, other metal dopant/substitute, and redox property of catalysts. In addition, H2O/SO2 tolerance and the NH3-SCR reaction mechanism over Fe-based catalysts, including Eley-Rideal and Langmuir-Hinshelwood mechanism, are emphasized. Lastly, the perspectives and future research directions of low-temperature NH3-SCR of NOx are also proposed. [ABSTRACT FROM AUTHOR]

ABSTRACT The time evolution of the methane reburn process at high temperature was investigated by the simulation method. The simulated results show that the time evolutions of each component are different with the stoichiometric ratio (SR) of the reburn zone and the reaction time. In the simulation conditions, CH4, C2H2, and H appear as SR is from 0.66 to 0.96; CH3 appears as SR is from 0.66 to 0.76; HCN, NH3, and HNCO appear as SR is from 0.66 to 0.86; OH appears as SR is from 0.82 to 0.96. In the case with SR of 0.76, C2H2 and CH3 only appear in the initial 0.2 s, NH3 and HNCO appear in the whole 2.0 s; In the case with SR of 0.82, C2H2 also appears in the initial 0.2 s, NH3 and HNCO only appear in initial 0.5 s, CH3 does not appear in the whole reaction time of 2.0 s. The reaction between CH3 and NO mainly occurs in the strong reducing atmosphere, and contributes significantly to remove NO to HCN, NH3, and HNCO. The interactions of NO with H and OH radicals mainly occur in the weak reducing atmosphere, and contribute to remove a small part of NO to N2. Through comparing the time evolutions of total fixed nitrogen (TFN) with different SR, it is suggested that the optimum SR for reducing TFN in the methane reburn process is about 0.82. © 2011 Curtin University of Technology and John Wiley & Sons, Ltd. [ABSTRACT FROM AUTHOR]

The selective catalytic reduction of NO with NH3 at low temperatures has been investigated with natural iron ore catalysts. Four iron ore raw materials from different locations were taken and processed to be used as catalysts. The methods of X-ray diffraction (XRD), X-ray fluorescence (XRF), Brunauer-Emmett-Teller (BET), X-ray photoelectron spectroscopy (XPS), hydrogen temperature-programmed reduction (H2-TPR), ammonia temperature-programmed desorption (NH3-TPD), scanning electron microscopy (SEM) and Fourier-transform infrared spectroscopy (FTIR) were used to characterize the materials. The results showed that the sample A (comprised mainly of α-Fe2O3 and γ-Fe2O3), calcined at 250 °C, achieved excellent selective catalytic reduction (SCR) activity (above 80% at 170–350 °C) and N2 selectivity (above 90% up to 250 °C) at low temperatures. Suitable calcination temperature, large surface area, high concentration of surface-adsorbed oxygen, good reducibility, lots of acid sites and adsorption of the reactants were responsible for the excellent SCR performance of the iron ore. However, the addition of H2O and SO2 in the feed gas showed some adverse effects on the SCR activity. The FT-IR analysis indicated the formation of sulfate salts on the surface of the catalyst during the SCR reaction in the presence of SO2, which could cause pore plugging and result in the suppression of the catalytic activity. [ABSTRACT FROM AUTHOR]