Search

The microcalorimetric hydrogen titration technique combined with conventional volumetric measurements has been used to reveal peculiarities of the hydrogenation of the single-phase TiZrVNbTa equiatomic high-entropy alloy. The alloy has been produced in the form of microfibers by the pendent drop melt extraction technique. Palladium coating of the fibers has been applied to enable first hydrogenation at room temperature without additional activation. An analysis of the obtained data allows us to evaluate the dependence of hydrogenation enthalpy on the hydrogen concentration in the alloy. Three concentration ranges, presumably related to the formation of the hydrogen solid solution, monohydride and dihydride phases, have been identified, and the corresponding ΔH values of about −100, −80 and −60 kJ/mol H2, respectively, have been determined.

In this work, composites based on a hydride-forming fiber of a multi-principal-component (MPC) Ti20Zr20Nb20V20Hf20 alloy, carbosil, dicumylperoxide and nitrile butadiene rubber (NBR) matrix were obtained. The composites were prepared in a three-stage process including the mixing of elastomeric compounds via a rubber mixing mill and low-temperature vulcanization by heat pressing. Using dynamical mechanical analysis (DMA) and differential scanning calorimetry (DSC) the effect of the metallic filler on the process of carbonization of the composite elastomeric matrix was studied. The microstructure and gas separation properties of the resulting composites were also studied. The results showed that the filler content increase in the elastomeric matrix leads to a noticeable and gradual decrease in the activation energy of the carbonization process, reduces the temperature of this process, and accelerates the growth of the elastic modulus during carbonization. It was shown that the finely dispersed fiber of the MPC acts as an activation center for the process of thermal-oxidative degradation in the elastomeric matrix accompanying the onset of carbonization. The gas permeability values were found to be relatively low and no visible correlation with the MPC alloy content in the composite membrane was observed.

Composites based on Zr65Cu17.5Ni10Al7.5/PTFE (polytetrafluoroethylene) with silane were prepared by ball milling with subsequent thermal pressing. Silanization was performed in the alcoholic solution with metallic glass powder. Different composites, 30/70 and 50/50 with silane, were prepared. During ball milling, Zr2Cu and Zr2Ni intermetallic phases were formed. The Zr-based metallic glass had a large supercooled region, and the melting point of the 30/70 and 50/50 composites with silane was near to the melting point of PTFE. The 50/50 composite (silane) had the highest thermal conductivity compared to the 30/70 composite samples. The incorporation of silane in metallic glass/polymer was investigated by Fourier-transform infrared spectroscopy (FTIR) and scanning electron microscope (SEM) analysis. Thermogravimetric analysis (TGA) showed the thermal stability of the composite samples up to 450–460 °C. It was also concluded that the 50/50 composite with silane has better thermal stability than the 30/70 composite with silane. The addition of silane in 30/70 and 50/50 composites increased the thermal conductivity compared to the composites without silane.

Metallic glasses are known for their mechanical properties but lack plasticity. This could be prevented by combining them with other materials or by inducing a second phase to form a composite. These composites have enhanced thermo-physical properties. The review paper aims to outline a summary of the current research done on metallic glass and its composites. A background in the history, properties, and their applications is discussed. Recent developments in biocompatible metallic glass composites, fiber-reinforced metallic glass, ex situ and in situ, are discussed.

Composites based on Zr65Cu17.5Ni10Al7.5 metallic glass (MG) and polytetrafluoroethylene (PTFE) were prepared by ball milling. Different composites (30/70, 50/50 and 70/30) were produced. Samples for dynamic mechanical analysis and laser flash analysis were fabricated in the supercooled region of the metallic glass and viscous region of the polymer. Spark plasma sintering (SPS) was performed at the supercooled region for the metallic glass powder. Characteristics such as thermal, mechanical, and structural properties were studied. A formation of the Zr2Cu and Zr2Ni intermetallic was found in the metallic glass after SPS. A formation of the nanocrystalline Zr2Cu was found in composite samples. Dynamical mechanical analysis (DMA) was used to study the mechanical behavior of the material. It was concluded that the 70/30-MG/PTFE composite sample had better thermal conductivity than the other composite samples. The thermal conductivity of the metallic glass was the highest among the samples and it increased with the MG content in composites.

In this work, the biomedical applicability and physical properties of magnesium-based metallic glass/polycaprolactone (PCL) composites are explored. The composites were fabricated via mechanical alloying and subsequent coextrusion. The coextrusion process was carried out at a temperature near to the supercooled liquid region of the metallic glass and the viscous region of the polymer. The structures, as well as thermal and mechanical properties of the obtained samples were characterized, and in vivo investigations were undertaken. The composite samples possess acceptable thermal and mechanical properties. Tensile tests indicate the ability of the composites to withstand more than 100% deformation. In vivo studies reveal that the composites are biologically compatible and could be promising for biomedical applications.

Rising demand for bone implants has led to the focus on future alternatives of alloys with better biocompatibility and mechanical strength. Thus, this research is dedicated to the synthesis and investigation of new compositions for low-alloyed Ti-based compounds, which conjoin relatively acceptable mechanical properties and low elastic moduli. In this regard, the structural and mechanical properties of α + β Ti-Fe-Cu-Sn alloys are described in the present paper. The alloys were fabricated by arc-melting and tilt-casting techniques which followed subsequent thermo-mechanical treatment aided by dual-axial forging and rolling procedures. The effect of the concentrations of the alloying elements, and other parameters, such as regimes of rolling and dual-axial forging operation, on the microstructure and mechanical properties were thoroughly investigated. The Ti94Fe1Cu1Sn4 alloy with the most promising mechanical properties was subjected to thermo-mechanical treatment. After a single rolling procedure at 750 °C, the alloy exhibited tensile strength and tensile plasticity of 1300 MPa and 6%, respectively, with an elastic modulus of 70 GPa. Such good tensile mechanical properties are explained by the optimal volume fraction balance between α and β phases and the texture alignment obtained, providing superior alternatives in comparison to pure α- titanium alloys.

A composite material based on polyethylene terephthalate (PET, about 1% by mass) and Al85Y8Ni5Co2 metallic glass was obtained by mechanical alloying and consequent spark plasma sintering. The spark plasma sintering was performed at a temperature near to the super cooled liquid region of the metallic glass. Mechanical properties and the structural characterization of the composite material were obtained. It was conceived that composite samples (Al85Y8Ni5Co2/PET) have a better thermal conductivity in comparison with pure PET samples. The formation of the crystalline phases causes degradation of physical properties. It was calculated that the activation energy for crystallization of the Al85Ni5Y8Co2 metallic glass is higher than that of the other types of metallic glasses (Mg67.5Ca5Zn27.5 and Cu54Pd28P18) used for composite preparation previously. This denotes a good thermal stability of the chosen metallic glass.