Search

In this paper, we investigate the primary-side control of a Wireless Power Transfer (WPT) link, i.e., the capability of delivering the optimal power level to the load without compromising system efficiency, by only sensing quantities available at the primary side. When adding a simple power regulator at the secondary side, we observe and analyze the existence of a Maximum Efficiency Transfer point, easily detectable at the primary side, and corresponding to the additional power regulator being barely on, with negligible dissipated power. More important, the approach does not require any advanced system modeling, nor the estimation of the system parameters. A theoretical model is developed and verified by measurements on a prototype built upon a 60 mW-class-E based WPT link working at 6.78 MHz.

A fully-integrated complementary metal-oxide semiconductor (CMOS) sensor for combined temperature and humidity measurements is presented. The main purpose of the device is to monitor the hermeticity of micro-packages for implanted integrated circuits and to ensure their safe operation by monitoring the operating temperature and humidity on-chip. The smart sensor has two modes of operation, in which either the temperature or humidity is converted into a digital code representing a frequency ratio between two oscillators. This ratio is determined by the ratios of the timing capacitances and bias currents in both oscillators. The reference oscillator is biased by a current whose temperature dependency is complementary to the proportional to absolute temperature (PTAT) current. For the temperature measurement, this results in an exceptional normalized sensitivity of about 0.77%/°C at the accepted expense of reduced linearity. The humidity sensor is a capacitor, whose value varies linearly with relative humidity (RH) with a normalized sensitivity of 0.055%/% RH. For comparison, two versions of the humidity sensor with an area of either 0.2 mm2 or 1.2 mm2 were fabricated in a commercial 0.18 μm CMOS process. The on-chip readout electronics operate from a 5 V power supply and consume a current of approximately 85 μA.

Inductive powering for implanted medical devices, such as implantable biosensors, is a safe and effective technique that allows power to be delivered to implants wirelessly, avoiding the use of transcutaneous wires or implanted batteries. Wireless powering is very sensitive to a number of link parameters, including coil distance, alignment, shape, and load conditions. The optimum drive frequency of an inductive link varies depending on the coil spacing and load. This paper presents an optimum frequency tracking (OFT) method, in which an inductive power link is driven at a frequency that is maintained at an optimum value to ensure that the link is working at resonance, and the output voltage is maximised. The method is shown to provide significant improvements in maintained secondary voltage and system efficiency for a range of loads when the link is overcoupled. The OFT method does not require the use of variable capacitors or inductors. When tested at frequencies around a nominal frequency of 5 MHz, the OFT method provides up to a twofold efficiency improvement compared to a fixed frequency drive. The system can be readily interfaced with passive implants or implantable biosensors, and lends itself to interfacing with designs such as distributed implanted sensor networks, where each implant is operating at a different frequency.

The total economic cost of neurological disorders exceeds £100 billion per annum in the United Kingdom alone, yet pharmaceutical companies continue to cut investments due to failed clinical studies and risk [1]. These challenges motivate an alternative to solely pharmacological treatments. The emerging field of bioelectronics suggests a novel alternative to pharmaceutical intervention that uses electronic hardware to directly stimulate the nervous system with physiologically inspired electrical signals [2]. Given the processing capability of electronics and precise targeting of electrodes, the potential advantages of bioelectronics include specificity in the time, method, and location of treatment, with the ability to iteratively refine and update therapy algorithms in software [3]. A primary disadvantage of the current systems is invasiveness due to surgical implantation of the device.

Wireless data telemetry for implantable medical devices (IMDs) has, in general, been limited to a few Mbps, and used for applications such as transmitting recordings from an implanted monitoring device, or uploading commands to an implanted stimulator. However, modern neural interfaces need to record high resolution potentials from hundreds of neurons; this requires much higher data rates. While fast wireless communication is possible using existing standards such as WiFi, power consumption demands are far too high for IMDs. Short range inductive link based telemetry, in particular impulse-based systems such as pulse-harmonic modulation (PHM), have demonstrated transfer speeds of up to 20 Mbps with a small power budget. However, these systems require complex and precise circuits, making them potentially susceptible to inter-symbol-interference. This work presents a new method named Short-range Quality-factor Modulation (SQuirM), which retains the low power consumption and high data rate of PHM, while improving the resilience of the system and simplifying the circuit design. Transmitter and receiver circuits were fabricated using 0.35 ${\mu }m$ CMOS. The circuits were capable of reliably transceiving data at speeds of up to 50.4 Mbps, with a BER of $ , and a transmitter energy consumption of 8.11 pJ/b.

We consider the design of Wireless Power Transfer (WPT) systems based on inductive links and focus on recent works where the whole WPT system (i.e. both energy transmitter and energy receiver) is designed as an isolated resonant class-E DC-DC converter characterized by a loosely-coupled transformer. The aim of this work is to compare the classic WPT design approach with a novel one, which allows achieving the same performance with a significant reduction in the number of reactive components of the circuit, with beneficial effects in terms of system complexity, size, and cost. We will also show that such a reduction in the number of reactive components leads to improved performance robustness to variations in the inductive link coupling factor.

Wireless biosensors are playing a pivotal role in health monitoring, disease detection and management. The development of wireless biosensor nodes and networks strongly relies on the design of novel low-power, low-cost and flexible CMOS sensor readouts. This brief presents a CMOS potentiostat that integrates a control amplifier, a dual-slope ADC and a wireless unit on the same chip. It implements a novel time-based readout scheme, whereby the counter of the dual-slope ADC is moved to the receiver and the sensor current is encoded in the timing between two wireless pulses transmitted via pulse-harmonic modulation across an inductive link. Measured results show that the potentiostat chip can resolve a minimum input current of 10pA at a sampling frequency of 125 Hz and a power consumption of $12~\mu \text{W}$ .

This paper presents a second-generation integrated circuit for the Active Books neural stimulation microsystem. It provides multi-channel stimulation with versatile control of stimulation profiles and reduced crosstalk from other stimulation channels. The new design features enhanced safety by monitoring the temperature and humidity inside the micropackage, and the peak electrode voltage at any stimulating electrode. The humidity sensor uses an interdigitated capacitor covered by a passivation layer and a polyimide covering. To boost sensitivity in the operating range of interest, the temperature sensor uses a temperature-insensitive current that is subtracted from a proportional-to-absolute-temperature current. A 3-b analog-to-digital converter is used to record the peak electrode voltage. All sensor data is sent to an implanted central hub using bidirectional connection with error checking. Both the stimulation electronics and sensors are integrated on a 6.2 mm $\times $ 4 mm silicon die using XFAB’s 0.6- $\mu \text{m}$ CMOS high-voltage process. No post-processing steps are involved. The stimulator uses a five-wire cable to provide the power supply and bidirectional data signals. The chip operates from a 7.5–18 V power supply and can generate stimulation currents of 1 mA, 4 mA or 8 mA with a pulse duration of 2 $\mu \text{s}$ –1.07 ms. The humidity sensor output varies linearly with relative humidity (RH) with a normalized sensitivity of 0.04%/%RH over the range of 20–90%RH. The temperature sensor has a nonlinearity of 0.4% over the range of 20–90 °C and a resolution of 0.12 °C. The stimulator is the first of its kind to include integrated temperature and humidity sensors.

The patch clamp has been widely considered the gold standard to measure intracellular ionic activity of single cells [1]. However, patch clamping is a laborious method and suffers from low throughput. To mitigate the disadvantages of patch clamping, planar patch clamp (PPC) chips with higher throughput have been recently introduced [2-3]. Yet those microfluidic chips do not allow to concurrently monitor the extracellular and the intracellular activity of the cells. Understanding of the complex cellular network activity and electrochemical processes, requires correlation between local field potentials (LFPs) of a population of cells and action potentials (APs) of single cells. This abstract presents a novel CMOS compatible microfluidic system that integrates flip-tip planar patch clamps (FTPPCs) and microelectrode arrays (MEAs) on the same wafer, for invitro extra- and intra-cellular recordings of electrical activity of cardiac cells. The device is fabricated using conventional wafer front- and back-side photolithography. The fabrication process leverages anisotropic wet etching selectivity of potassium hydroxide (KOH) and deep reactive ion etching (DRIE) to pattern FTPPCs. Before DRIE process, plasma-enhanced chemical vapor deposition (PECVD) of silicon dioxide (SiO2) is applied as passivation layer. After DRIE process, a metallization step is performed by sputtering titanium nitride (TiN) on patterned structures. As the final step, SiO2 is removed and backside DRIE is used to open apertures approximately with 2 µm diameter. The FTPPCs are intended to have a tip in 20 µm depth after KOH etching, and a spacing of 200 µm to ensure that mechanical stability of the device after DRIE. The planar MEAs are then patterned on the front side with 50 µm diameter and a pitch of 200 µm. A PDMS culture chamber is attached the front-side of the wafer, while a PDMS microfluidic channel is constructed on the back-side. By applying suction through the microfluidic channels, the cells are trapped in the FTPPC apertures. Potentiostatic measurements are used to record the ionic activity of the cells intracellularly, while low-noise instrumentation amplifiers are used in combination with the MEAs, to concurrently measure LPFs. Co-integration of PPC and MEAs on the same wafer can provide valuable insight in the correlation between sing

Powering of medical implants by inductive coupling is an effective technique, which avoids the use of bulky implanted batteries or transcutaneous wires. On the external unit side, class-D and class-E power amplifiers (PAs) are conventionally used, thanks to their high efficiency at high frequencies. The initial specifications driving this study require the use of multiple independent stimulators, which imposes serious constraints on the area and functionality of the external unit. An integrated circuit class-D PA has been designed to provide both small area and enhanced functionality, the latter achieved by the addition of an on-chip (PLL) a dead-time generator and a phase detector. The PA was designed in a 0.18- $\mu$ m CMOS high-voltage process technology and occupies an area of 9.86 mm $^2$ . It works at frequencies up to 14 MHz and 30-V supply and efficiencies higher than 80 $\%$ are obtained at 14 MHz. The PA is intended for a closed-loop transmitter system that optimizes power delivery to medical implants.

Point-of-care (PoC) diagnostics rely on the design of low-power and miniaturized readout units that can offer rapid and accurate test results, replacing the need for specialized equipment. CMOS technology can be exploited in order to design complex systems while achieving high energy efficiency for suitable operation in a mobile settings. This paper presents the design of a novel energy-efficient 4-channel wireless potentiostat chip, based on a dual-slope ADC architecture, that features a low-complexity wireless unit and a calibration approach that does not require additional circuitry. The chip was designed in a 0.35μm CMOS process. The simulated results suggest that each potentiostat channel can achieve an estimated energy efficiency of 2.5 pJ/bit from a 1.2 V supply.

A novel pixel architecture for CMOS image sensors is presented. It uses only one amplifier for both integration of the photocurrent and in-pixel noise cancelation, thus minimizing power consumption. The circuit is specifically designed to be used in readout systems for lateral flow immunoassays. In addition a switching technique is introduced enabling the use of column correlated double sampling technique in capacitive transimpedance amplifier pixel architectures without the use of any memory cells. As a result the reset noise which is crucial in these architectures can be suppressed. The circuit has been designed in a 0.35-μm CMOS technology and simulations are presented to show its performance.

Presents corrections to the paper, “Practical inductive link design for biomedical wireless power transfer: A tutorial,” (Schormans, M., et al), IEEE Trans. Biomed. Circuits Syst., vol. 12, no. 5, pp. 1112–1130, Oct. 2018.

Inductive powering for implanted medical devices, such as implantable biosensors, is a safe and effective technique that allows power to be delivered to implants wirelessly, avoiding the use of transcutaneous wires or implanted batteries. Wireless powering is very sensitive to a number of link parameters, including coil distance, alignment, shape, and load conditions. The optimum drive frequency of an inductive link varies depending on the coil spacing and load. This paper presents an optimum frequency tracking (OFT) method, in which an inductive power link is driven at a frequency that is maintained at an optimum value to ensure that the link is working at resonance, and the output voltage is maximised. The method is shown to provide significant improvements in maintained secondary voltage and system efficiency for a range of loads when the link is overcoupled. The OFT method does not require the use of variable capacitors or inductors. When tested at frequencies around a nominal frequency of 5 MHz, the OFT method provides up to a twofold efficiency improvement compared to a fixed frequency drive. The system can be readily interfaced with passive implants or implantable biosensors, and lends itself to interfacing with designs such as distributed implanted sensor networks, where each implant is operating at a different frequency.