Search

Nowadays, the integration of smart systems within the modern industrial scenario is a continuously growing paradigm. Computer Numerical Control (CNC) machinery can heavily benefit from the introduction of Artificial Intelligence (AI) based monitoring applications. In this paper, we present an industrial condition and fault prevention monitoring system for CNC tools. The developed system is the result of an industrial project aimed at realizing a multi-purpose machine which is currently in pre-commercial stage. The results of this work represent the base platform for the further commercial development, which will be carried on from the industrial partners in accordance with clients feedbacks and specifications. This work presents the hardware architecture of the system, the web-based monitoring platform for remote management, and the AI framework used for fault monitoring. The multi-purpose machine is equipped with accelerometer units to monitor the vibration in multiple points of the structure. The control unit of the machine is connected to the sensing nodes and is used to communicate the actual machine state to a remote web platform. The accelerometric data are analyzed through an AI algorithm to perform fault detection. The fault detection algorithm was trained with the measurements performed on the machine under controlled environment faulty operation. The Internet of Things (IoT) based architecture has proven to be effective to facilitate the supervision of the machining processes, and the AI-based classification shows good classification performances for the fault detection tests.

Nowadays quick fabrication of mechanical spare and replacement has become more and more necessary. This is the main reason why rapid prototyping and additive manufacturing has spread in several fields, including sensor manufacturing. In this work, we propose a Fused-Deposition-Fabricated Electro-Mechanical System (FDFEMS) accelerometer sensor. As the name suggests, it was implemented with Fused Deposition Modelling (FDM) additive manufacturing and material switching capabilities of the E3D ToolChanger motion platform. Fabrication process is based on insulating plastic to implement the mechanical structure of the device, conducting plastic to manufacture the actual differential capacitance sensing element and soluble material for sacrificial scaffolding. Together with the accelerometer, we also propose a novel fully differential interface circuit for differential capacitive sensors, based on the autobalanced bridge theory where capacitive sensor variations are balanced through voltage-controlled impedances placed in the bridge branches. Measurements from the sensor system were compared to theoretical values, showing good agreement. Furthermore, these measurements were repeated with different sensors and different test masses, to determine variations of the parameters evaluated. Specifically, measured sensitivity, damping factor and quality factor, with a fill factor of 100%, have resulted equal to 0.201 V/g, 0.055, and 9.042, respectively. It was then observed that the decrease of the proof mass fill factor led to a higher sensor resonant frequency, hence a wider flat band region in the frequency response, with decreased sensitivity and resolution. Mainly, this paper aims to evaluate and discuss the feasibility of the 3D printing Fused Deposition Modelling technique for manufacturing accelerometer sensors and classify sensor parameters as a function of its internal density, that is an easily selectable parameter for this kind of modelling.

Computer vision (CV)-based systems using cameras and recognition algorithms offer touchless, cost-effective, precise, and versatile hand tracking. These systems allow unrestricted, fluid, and natural movements without the constraints of wearable devices, gaining popularity in human–system interaction, virtual reality, and medical procedures. However, traditional CV-based systems, relying on stationary cameras, are not compatible with mobile applications and demand substantial computing power. To address these limitations, we propose a portable hand-tracking system utilizing the Leap Motion Controller 2 (LMC) mounted on the head and controlled by a single-board computer (SBC) powered by a compact power bank. The proposed system enhances portability, enabling users to interact freely with their surroundings. We present the system’s design and conduct experimental tests to evaluate its robustness under variable lighting conditions, power consumption, CPU usage, temperature, and frame rate. This portable hand-tracking solution, which has minimal weight and runs independently of external power, proves suitable for mobile applications in daily life.

Appropriate daylight control could maximize occupants’ visual comfort, potentially saving energy. However, the deployment of daylight control systems (DLCSs) is not happening, mainly due to the complex system calibration and the frequent reluctance of occupants toward automatic control systems that exclude their participation. In this paper, a human-in-the-loop DLCS is presented. The system is designed to allow the users to have direct interaction via smartphone Bluetooth communication, enabling them to set the lighting values deemed most comfortable nimbly. Special attention has been paid to the power consumption of the DLCS, especially in standby mode. Accessibility of configuration has been taken into consideration, leading to the choice of a wireless configured device. The performance of the prototype DLCS was evaluated experimentally in a side-lit room and compared with that of a commercial controller. The illuminance on a reference work plane was measured during the operation of the systems to observe the controllers’ effect on the lamp’s luminous flux while simultaneously considering the variation of daylight conditions. Moreover, the energy performance of the systems was studied to obtain information about the energetic effectiveness and convenience of the studied DLCSs. The main results showed that the proposed system could maintain the required target illuminance values on the work plane as daylight conditions vary: the maximum deviation measured using the prototype never exceeded 11 lx. In comparison, the commercial controller reached peaks of 220 lx. Moreover, the energy consumption of the prototype (resulting equal to 370 mVA) was lower than the consumption of the commercial system (equal to 600 mVA), allowing for increased energy savings over the long period. The more straightforward configuration allows the user to better interact with the DLCS.

Rockfalls and landslide events are caused by different factors among which are included geomorphological and climatic factors and also human interaction. Therefore, the economic and social impacts can be significant and the remote monitoring of such hazards has become an essential topic in various applications. Wireless sensor networks (WSNs) are well suited for the deployment of monitoring systems, benefiting from the different technologies and topologies that are available and evolving nowadays. This review paper aims to summarize and overview the up-to-date state of the art of rockfall and landslide monitoring systems based on WSNs. The implementation and methods were analyzed for each solution, along with the system architecture and relevant hardware aspects. All the retrieved data were used to analyze the current trends and future possibilities in the field of WSN geohazard monitoring.

In this work we present a synthesis method for the design of RF and microwave Active Inductors (AI) based on S-parameters and conformal transformations. The proposed approach allows to study and define the desired AI characteristics directly managing the transfer function of an equivalent two-ports network, thus overcoming the difficulties relative to the characterization of the classical closed-loop architecture that characterizes both the proposed AI architecture and the classical gyrator-C capacitor scheme. By analyzing the obtained AI open-loop transfer function, it is possible to define the design criteria useful to obtain a single port equivalent network showing an inductive behavior at the desired frequency. An example of application of the proposed approach is also provided and the obtained AI is used for the design of a low-power active filter. Measurements are in good agreement with the simulation results, demonstrating the feasibility of the proposed design approach.

In this study, a review of second-generation voltage conveyor (VCII) and current conveyor (CCII) circuits for the conditioning of bio signals and sensors is presented. The CCII is the most known current-mode active block, able to overcome some of the limitations of the classical operational amplifier, which provides an output current instead of a voltage. The VCII is nothing more than the dual of the CCII, and for this reason it enjoys almost all the properties of the CCII but also provides an easy-to-read voltage as an output signal. A broad set of solutions for relevant sensors and biosensors employed in biomedical applications is considered. This ranges from the widespread resistive and capacitive electrochemical biosensors now used in glucose and cholesterol meters and in oximetry to more specific sensors such as ISFETs, SiPMs, and ultrasonic sensors, which are finding increasing applications. This paper also discusses the main benefits of this current-mode approach over the classical voltage-mode approach in the realization of readout circuits that can be used as electronic interfaces for different types of biosensors, including higher circuit simplicity, better low-noise and/or high-speed performance, and lower signal distortion and power consumption.

It is necessary to ensure safety in terms of health and accidents through the real-time monitoring of the construction site environment and workers. This problem has become of great importance due to the economic and social implications. Therefore, a sensor-based approach has been found to be beneficial in Building Information Modeling (BIM). Wireless Sensor Network (WSN) technologies are well-suited for the deployment of monitoring systems. A suitable technical solution for node communication in a WSN is Long Range (LoRa) modulation technology. In this study, an autonomous LoRa-based system for the monitoring of a construction site in Lungro, Calabria, Italy, is presented. The spatial monitoring of working personnel is achieved by employing a tracker device with an Inertial Measurement Unit (IMU) and a Global Positioning System (GPS) device. Accesses of personnel and gear to the site are registered using Radio Frequency Identification (RFID) tags equipped with protective gear. Fixed-position solar-powered sensor nodes are also employed for structural monitoring, i.e., movement sensors are used to monitor the variation of scaffolding, building structures, and under-work housing inclinations. Long Range Wide Area Network (LoRaWAN) gateways interface with the nodes and the internet for data exchange, enabling an Internet of Things (IoT) paradigm for the monitoring solution. A comprehensive overview of the workers and structural nodes, along with the RFID access management system and LoRaWAN gateway features, is provided in this article. A description of the web interface is also reported.

We here present a 10-17 Degrees of Freedom (DoF) sensory gloves for Smart Healthcare implementing an energy harvesting architecture, aimed at enhancing the battery lasting when powering the electronics of the two different types of gloves, used to sense fingers movements. In particular, we realized a comparison in terms of measurement repeatability and reliability, as well as power consumption and battery lasting, between two sensory gloves implemented by means of different technologies. The first is a 3D printed glove with 10 DoF, featuring low-cost, low-effort fabrication and low-power consumption. The second is a classical Lycra® glove with 14 DoF suitable for a more detailed assessment of the hand postures, featuring a relatively higher cost and power consumption. An electronic circuitry was designed to gather and elaborate data from both types of sensory gloves, differing for number of inputs only. Both gloves are equipped with flex sensors and in addiction with the electronics (including a microcontroller and a transmitter) allow the control of hand virtual limbs or mechanical arts in surgical, military, space and civil applications.Six healthy subjects were involved in tests suitable to evaluate the performances of the proposed gloves in terms of repeatability, reproducibility and reliability. Particular effort was devoted to increase battery lasting for both glove-based systems, with the electronics relaying on Radio Frequency, Piezoelectric and Thermoelectric harvesters. The harvesting part was built and tested as a prototype discrete element board, that is interfaced with an external microcontroller and a radiofrequency transmitter board. Measurement results demonstrated a meaningful improvement in battery operation time up to 25%, considering different operating scenarios.

This work deals with the design of a new readoutelectronics for silicon photomultipliers sensors. The so-calledSiPMs sensors are an emerging technology currentlydiffusing in many applications and, among them, in thedefinition of a new generation of LIDAR systems. Thelatter, nowadays have a primary role in the evolutionprocess that is involving Smart Cities, being an enablingtechnology in different fields. The solution here proposed isrealized at electronic level with a 150 nm technology processfrom LFoundry and results provide a feasibledemonstration of the capability of the proposed designapproach to be employed in practical application.

Rockfalls and landslides are hazards triggered from geomorphological and climatic factors other than human interaction. The economic and social impacts are not negligible, therefore the topic has become an important field in the application of remote monitoring. Wireless sensor networks (WSNs) are particularly suited for the deployment of such systems, thanks to the different technologies and topologies that are evolving nowadays. Among these, LoRa modulation technique represents a fitting technical solution for nodes communication in a WSN. In this paper, a smart autonomous LoRa-based rockfall and landslide monitoring system is presented. The structure has been operating in Pantelleria Island, Sicily, Italy. The sensing elements are disposed in sensor nodes arranged in a star topology. Network access to the LoRaWAN and the Internet is provided through gateways using a portable, solar powered device assembly. A system overview concerning both hardware and functionality of the nodes and gateways devices, then a power analysis is reported, and a monthly recorded result is presented, with related discussion.

The need for accurate information and the availability of novel tool and technological advances in agriculture have given rise to innovative autonomous systems. The aim is to monitor key parameters for optimal water and fertilizer management. A key issue in precision agriculture is the in situ monitoring of soil macronutrients. Here, a proof-of-concept study was conducted that tested two types of sensors capable of capturing both the electrochemical response of the soil and the electrical potential generated by the interaction between the soil and plants. These two sensors can be used to monitor large areas using a network approach, due to their small size and low power consumption. The voltammetric sensor (BIONOTE-L) proved to be able to characterize different soil samples. It was able, indeed, to provide a reproducible voltammetric fingerprint specific for each soil type, and to monitor the concentration of CaCl2 and NaCl in the soil. BIONOTE-L can be coupled to a device capable of capturing the energy produced by interactions between plants and soil. As a consequence, the functionality of the microsystem node when applied in a large-area monitoring network can be extended. Additional calibrations will be performed to fully characterize the instrument node, to implement the network, and to specialize it for a particular application in the field.

This study reviews second-generation voltage conveyor (VCII)-based read-out circuits for sensors and bioelectrical signal conditioning from existing literature. VCII is the dual circuit of a second-generation current conveyor (CCII), which provides the possibility of processing signals in the current domain while providing output signals in the voltage form. The scope of this paper is to discuss the benefits and opportunities of new VCII-based read-out circuits over traditional ones and bioelectrical signals. The achieved main benefits compared to conventional circuits are the simpler read-out circuits, producing an output signal in a voltage form that can be directly used, improved accuracy, possibility of gain adjustment using a single grounded resistor, and the possibility of connecting several SiPM sensors to the readout circuit. The circuits studied in this paper include VCII- based read-out circuits suitable for all types of sensors configured in the current-mode Wheatstone bridge (CMWB) topology, the VCII-based read-out circuits solutions reported for silicon photomultiplier, spiral-shaped ultrasonic PVDF and differential capacitive sensors, and, finally, a simple readout circuitry for sensing bioelectrical signals. There are still not many VCII-based readout circuits, and we hope that the outcome of this study will enhance this area of research and inspire new ideas.

In this work we present a combined 90/900 MHz Energy Harvesting Architecture for active smart tag Application. The harvester takes advantages from a dedicated diplexer and a power manager for battery life enhancement purposes. The system has been optimized in the 900 MHz frequency range by analyzing a probabilistic approach used for modeling the possible amount of Global System for Mobile communication (GSM) energy that could be harvested while a fixed power downlink scenario has been adopted for the 90MHz band. A preliminary IC system with a 0.18μm CMOS SMIC technology has been designed and optimized at 90 and 900 MHz while discrete element board, to be integrated with the proposed IC, with commercial components has been developed and tested. Concerning simulation results on the IC design they have confirmed that the integrated system handles an incoming power typically ranging from -25 dBm to 5 dBm by rectifying the variable input signals into a DC voltage source with an average 50% efficiency.

The aim of this paper is to prove that, through a canonic approach, sinusoidal oscillators based on second-generation voltage conveyor (VCII) can be implemented. The investigation demonstrates the feasibility of the design results in a pair of new canonic oscillators based on negative type VCII (VCII−). Interestingly, the same analysis shows that no canonic oscillator configuration can be achieved using positive type VCII (VCII+), since a single VCII+ does not present the correct port conditions to implement such a device. From this analysis, it comes about that, for 5-node networks, the two presented oscillator configurations are the only possible ones and make use of two resistors, two capacitors and a single VCII−. Notably, the produced sinusoidal output signal is easily available through the low output impedance Z port of VCII, removing the need for additional voltage buffer for practical use, which is one of the main limitations of the current mode (CM) approach. The presented theory is substantiated by both LTSpice simulations and measurement results using the commercially available AD844 from Analog Devices, the latter being in a close agreement with the theory. Moreover, low values of THD are given for a wide frequency range.

In this work we present an IC architecture for RF energy harvesting. The system has been designed with a 0.18μm CMOS SMIC technology and optimized at 900MHz. Simulation results have confirmed that the integrated system handles an incoming power typically ranging from -25 dBm to 20 dBm by rectifying the variable input signals into a DC voltage source with an overall efficiency up to 50%. The chip area estimation for the proposed system is as low as 3x3mm2.

Exploiting the transmission and reception of low frequency ultrasounds in air is often associated with the innate echolocating abilities of some mammals, later emulated with sophisticated electronic systems, to obtain information about unstructured environments. Here, we present a novel approach for the reception of ultrasounds in air, which exploits a piezopolymer broadband sensor and an electronic interface based on a second-generation voltage conveyor (VCII). Taking advantage of its capability to manipulate both voltage and current signals, in this paper, we propose an extremely simple interface that presents a sensitivity level of about −100 dB, which is in line with commercially available references. The presented results are obtained without any filtration stage. The second-generation voltage conveyor active device is implemented through a commercially available AD844, with a supply voltage of ±15 V.

In the last decades, the applications of structural monitoring are moving toward the field of civil engineering and infrastructures. Nevertheless, if the structures have damages, it does not mean that they have a complete loss of functionality, but rather that the system is no longer in an optimal condition so that, if the damage increases, the structure can collapse. Structural Health Monitoring (SHM), a process for the identification of damage, periodically collects data from suitable sensors that allow to characterize the damage and establishes the health status of the structure. Therefore, this monitoring will provide information on the structure condition, mostly about its integrity, in a short time, and, for infrastructures and civil structures, it is necessary to assess performance and health status. The aim of this work is to design an Internet of Things (IoT) system for Structural Health Monitoring to find possible damages and to see how the structure behaves over time. For this purpose, a customized datalogger and nodes have been designed. The datalogger is able to acquire the data coming from the nodes through RS485 communication and synchronize acquisitions. Furthermore, it has an internal memory to allow for the post-processing of the collected data. The nodes are composed of a digital triaxial accelerometer, a general-purpose microcontroller, and an external memory for storage measures. The microcontroller communicates with an accelerometer, acquires values, and then saves them in the memory. The system has been characterized and the damage indicator has been evaluated on a testing structure. Experimental results show that the estimated damage indicator increases when the structure is perturbed. In the present work, the damage indicator increased by a maximum value of 24.65 when the structure is perturbed by a 2.5 mm engraving.

The development of Internet of Things (IoT) systems is a rapidly evolving scenario, thanks also to newly available low-power wide area network (LPWAN) technologies that are utilized for environmental monitoring purposes and to prevent potentially dangerous situations with smaller and less expensive physical structures. This paper presents the design, implementation and test results of a flood-monitoring system based on LoRa technology, tested in a real-world scenario. The entire system is designed in a modular perspective, in order to have the capability to interface different types of sensors without the need for making significant hardware changes to the proposed node architecture. The information is stored through a device equipped with sensors and a microcontroller, connected to a LoRa wireless module for sending data, which are then processed and stored through a web structure where the alarm function is implemented in case of flooding.

This work presents the design of a discrete second-generation voltage conveyor (VCII) and its capability to be used as electronic interface for silicon photomultipliers. The design addressed here exploits directly at the transistor level, with commercial components, the proposed interface; the obtained performance is valuable considering both the discrete elements and the application. The architecture adopted here realizes a transimpedance amplifier that is also able to drive very high input impedance, as usually requested by photons detection. Schematic and circuital design of the discrete second-generation voltage conveyor is presented and discussed. The complete circuit interface requires a bias current of 20 mA with a dual 5V supply voltage; it has a useful bandwidth of about 106 MHz, and considering also the reduced dimensions, it is a good candidate to be used in portable applications without the need of high-cost dedicated integrated circuits.

The evaluation of photovoltaic (PV) system’s efficiency loss, due to the onset of faults that reduce the output power, is crucial. The challenge is to speed up the evaluation of electric efficiency by coupling the electric characterization of panels with information gathered from module diagnosis, amongst which the most commonly employed technique is thermographic inspection. The aim of this work is to correlate panels’ thermal images with their efficiency: a “thermal signature” of panels can be of help in identifying the fault typology and, moreover, for assessing efficiency loss. This allows to identify electrical power output losses without interrupting the PV system operation thanks to an advanced PV thermography characterization. In this paper, 12 faulted working panels were investigated. Their electrical models were implemented in MATLAB environment and developed to retrieve the ideal I-V characteristic (from ratings), the actual (operative) I-V characteristics and electric efficiency. Given the curves shape and relative difference, based on three reference points (namely, open circuit, short circuit, and maximum power points), faults’ typology has been evidenced. Information gathered from infrared thermography imaging, simultaneously carried out on panels during operation, were matched with those from electrical characterization. Panels’ “thermal signature” has been coupled with the “electrical signature”, to obtain an overall depiction of panels’ health status.

This work proposes a new simplified five-parameter estimation method for a single-diode model of photovoltaic panels. The method, based on an iterative algorithm, is able to estimate the parameter of the electrical single-diode model from the panel’s datasheet. Two iterative steps are used to estimate the five parameters starting from data provided by the manufacturer (nameplate values or I−V curves). The first step permits finding the optimal value of the diode ideality factor A, and the second step allows the calculation of the Rp value to improve the accuracy. A model that takes into account variations in temperature and solar irradiance has been used to validate the behavior of the output parameters. Compared to other estimation work, the proposed method shows the best result in the standard test condition (STC) and with a variable solar irradiance. Indeed, the optimization of the A, Rs, and Rp parameters allows guaranteeing the minimum error between I−V curves obtained from method and datasheet.

In this paper, a novel approach to implement a stray insensitive CMOS interface for differential capacitive sensors is presented. The proposed circuit employs, for the first time, second-generation voltage conveyors (VCIIs) and produces an output voltage proportional to differential capacitor changes. Using VCIIs as active devices inherently allows the circuit to process the signal in the current domain, and hence, to benefit from its intrinsic advantages, such as high speed and simple implementation, while still being able to natively interface with voltage mode signal processing stages at necessity. The insensitiveness to the effects of parasitic capacitances is achieved through a simple feedback loop. In addition, the proposed circuit shows a very simple and switch-free structure (which can be used for both linear and hyperbolic sensors), improving its accuracy. The readout circuit was designed in a standard 0.35 μm CMOS technology under a supply voltage of ±1.65 V. Before the integrated circuit fabrication, to produce tangible proof of the effectiveness of the proposed architecture, a discrete version of the circuit was also prototyped using AD844 and LF411 to implement a discrete VCII. The achieved measurement results are in good agreement with theory and simulations, showing a constant sensitivity up to 412 mV/pF, a maximum linearity error of 1.9%FS, and acknowledging a good behavior with low baseline capacitive sensors (10 pF in the proposed measurements). A final table is also given to summarize the key specs of the proposed work comparing them to the available literature.

In this paper, a novel integrated measuring and control system for hot box experiments is presented. The system, based on a general-purpose microcontroller and on a wireless sensors network, is able to fully control the thermal phenomena inside the chambers, as well as the heat flux that involves the specimen wall. Thanks to the continuous measurements of air and surfaces temperatures and energy input into the hot chamber, the thermal behavior of each hot box component is analyzed. A specific algorithm allows the post-process of the measured data for evaluating the specimen wall thermal quantities and for creating 2D and 3D thermal models of each component. The system reliability is tested on a real case represented by a double insulating X-lam wall. The results of the 72 h experiment show the system’s capability to maintain stable temperature set points inside the chambers and to log the temperatures measured by the 135 probes, allowing to know both the U-value of the sample (equal to 0.216 ± 0.01 W/m2K) and the thermal models of all the hot box components. The U-value obtained via hot box method has been compared with the values gathered through theoretical calculation and heat flow meter measurements, showing differences of less than 20%. Finally, thanks to the data postprocessing, the 2D and 3D thermal models of the specimen wall and of the chambers have been recreated.

The background shows that intervention on historical walls highlights the difficulty of identifying design solutions that are effective and compatible due to the lack of specific data on the thermal characteristics of the specific contexts investigated. This determines the choice of design solutions that are frequently inadequate and unsustainable from an environmental and economic point of view. Starting from acquired data a methodology has been developed that is based on in situ experimental investigations able to return the most probable value of transmittance of the historical walls. The values measured on the samples analysed do not reflect the literature data. For some of the samples analysed, the measured transmittance is lower than the one recorded in literature of about 10⁻15%. For the remaining ones, there are no reference values. The importance of an in-depth knowledge of the real behaviour of an existing historical envelope of a building is therefore fundamental, given that any evaluation mistake can have serious consequences from both an economic and environmental point of view. Underestimating the transmittance of a wall implies a waste in the use of available resources but also the disposal of greater quantities of building materials in relation to the end of life. The developed methodology can be easily replicated in other contexts and extended to all building elements that make up the historical envelope. The study will be continued by analysing further samples in order to create a reference knowledge database accessible to researchers, professionals and organizations.

Recent advances in sensing technologies, especially those for Microsensor Integrated Systems, have led to several new commercial applications. [...]

In this manuscript, the authors propose a novel interface for silicon photomultipliers based on a second-generation voltage conveyor as an active element, performing as a transimpedance amplifier. Due to the absence of internal feedback, this solution offers a static bandwidth regardless of the tunable gain level. The simulation results have shown good performances, confirming the possibility of the proposed interface being effectively used in different scenarios. A preliminary hybrid solution has also been developed using second-generation current conveyors and measurements conducted on an equivalent discrete-elements board, which is promising.

The study of ladder networks made by sequences of directly coupled inductor–capacitor single cells has led us to discover a new property, which may be of certain interest in the sensor field. In the case of n cells, the n-frequencies vector characterizing each node may allow for the identification of that capacitor (sensor), which has experienced a variation of its nominal value. This localization is possible independently from the observable node of the ladder network as proven by the application of the following multivariate data analysis techniques: principal component analysis and partial least square discriminant analysis. This property can be applied on a large scale down to micrometric dimensions in agreement with the technologic ability to shrink the capacitive sensor dimensions.

In this work, the authors introduce a new full-analog front-end for differential capacitance sensors which provides a DC output voltage, directly proportional to the measurand variations. The readout circuit architecture is based on a De Sauty bridge as core of the capacitive sensing whereas the feedback circuitry performs the bridge autobalancing operation by means of changes in a multiplier output. The circuit is designed in a standard CMOS technology (AMS 0.35 µm) so is suitable for portable systems. Simulated results have shown a good agreement with the theoretical model being the percentage relative error less than 2.5%. Interface sensitivity is constant and values around 0.055 V/mm for the considered application.

In this work, the authors propose a novel directional anemometric system, showing a compact design and the absence of external mechanical moving parts. The measuring principle is based on a dual channel spherical wind conveyor structure, combined with a pressure difference sensing technique of the conveyed air flows by the employment of electromagnetic inductive transducers.

In this work, we present a flexible and multi-probe temperature measurement system, suitable for real time monitoring and long-term applications. The proposed sensor system allows to investigate the thermal performance of different environments such as building areas, walls or external places. The equipment has been characterized both at device and system levels and validated through experimental tests through a comparison with different sensors. The conceived system consists of a control unit with a microcontroller, a user interface and an internal recording section for data storage and management, and digital temperature sensors with a 12-bit resolution, whose number can be freely defined, having the system a modular architecture. The low-cost and open-source characteristics, beyond of its flexibility and capability to manage several sensors placed also very far from the control unit (up to 500 m), make the proposed solution a suitable candidate to be used for practical applications that require on-field measurements.

In this work; we present an innovative sensing system able to recognize a rock fall event and to monitor the structural parameters of a falling rock protection barrier. The system has been conceived and optimized for any protection barrier; gabion mesh or concrete blocks; it has a modular and flexible architecture; organized with a control unit and sensing nodes that can be arranged directly on the considered site. This architecture provides information about the vibration and the inclination of the falling rock protection barrier. The data; continuously monitored; are collected on a web server responsible to check the overall status of the barrier itself and to generate and send automatic messages for any criticisms. A web application has been also developed for system monitoring; to create summary report and to analyze the data collected. The novel system is currently working on a gabion protecting mesh installed in the south of Italy.

Sensors for monitoring oxygen and carbon dioxide are crucial as investigational devices in many different research fields, including environmental, biomedical and industrial. They must be easily configurable, fast responding, and with good reproducibility and sensitivity. The state of art reports different sensing and transducing strategies: electrochemical, optical, conductometric etc., based on specific chemically interactive materials. In this work, a multisensor system based on electrochemical sensors acting via a liquid medium and controlled by a dedicated low-noise electronic interface is equipped with an elaboration unit able in extracting/storing a committed model for oxygen and carbon dioxide detection.