Search

The baseball pitch is a repetitive, full-body throwing motion that exposes the elbow to significant loads, leading to a high incidence of elbow injuries. Elbow injuries in pitching are often attributed to high external valgus torques as these are generally considered to be a good proxy for the load on the Ulnar Collateral Ligament. The aim of the study is to contribute to elbow load monitoring by developing a prediction model based on the pelvis and trunk peak angular velocities and their separation time. Eleven male youth elite baseball pitchers (age 17 ± 2.2 years) threw 25 fastballs at full effort off a mound. Two-level varying-intercept, varying-slope Bayesian models were used to predict external valgus torque based on (inter)segmental rotation in fastball pitching with pitcher’s weight and height added to strengthen the individualisation of the prediction. The results revealed the high predictive performance of the models including a set of kinematic parameters trunk peak angular velocity and the separation time between the pelvis and trunk peak angular velocities. Such an approach allows individualised prediction of the external valgus torque for each pitcher, which has a great practical advantage compared to group-based predictions in terms of injury assessment and injury prevention., Statistics, Biomechatronics & Human-Machine Control

In wheelchair sports, there is an increasing need to monitor mechanical power in the field. When rolling resistance is known, inertial measurement units (IMUs) can be used to determine mechanical power. However, upper body (i.e., trunk) motion affects the mass distribution between the small front and large rear wheels, thus affecting rolling resistance. Therefore, drag tests – which are commonly used to estimate rolling resistance – may not be valid. The aim of this study was to investigate the influence of trunk motion on mechanical power estimates in hand-rim wheelchair propulsion by comparing instantaneous resistance-based power loss with drag test-based power loss. Experiments were performed with no, moderate and full trunk motion during wheelchair propulsion. During these experiments, power loss was determined based on 1) the instantaneous rolling resistance and 2) based on the rolling resistance determined from drag tests (thus neglecting the effects of trunk motion). Results showed that power loss values of the two methods were similar when no trunk motion was present (mean difference [MD] of 0.6 ± 1.6 %). However, drag test-based power loss was underestimated up to −3.3 ± 2.3 % MD when the extent of trunk motion increased (r = 0.85). To conclude, during wheelchair propulsion with active trunk motion, neglecting the effects of trunk motion leads to an underestimated mechanical power of 1 to 6 % when it is estimated with drag test values. Depending on the required accuracy and the amount of trunk motion in the target group, the influence of trunk motion on power estimates should be corrected for., Biomechanical Engineering, Biomechatronics & Human-Machine Control

Background: In baseball, repetitive pitching leads to medial elbow injuries, particularly to the ulnar collateral ligament (UCL). To prevent pitchers from UCL injuries, it is important to quantify the response to elbow stress. Repetitive elbow external valgus torque and muscular fatigue induced by repetitive pitching could affect markers of the response, that is, humeroulnar joint gap and UCL morphology. The aims of the study were three-folded: to investigate the effect of (1) exerted handgrip force on the humeroulnar joint gap, (2) repetitive pitching on the humeroulnar joint gap and the UCL morphology, and (3) exerted handgrip force on the humeroulnar joint gap for different levels of elbow valgus stress is different after compared to before repetitive pitching in asymptomatic baseball pitchers. Methods: Medial elbow ultrasound images were collected in 15 asymptomatic male baseball pitchers. Three levels of static elbow valgus stress (0N, 50N, 100N) were applied with a TELOS device before and after repetitive pitching and with or without handgrip force. These images were used to assess the humeroulnar joint gap size and UCL length and thickness. After 110 fastball pitches or when 80% self-perceived fatigue on a VAS scale was reached, participants were instructed to stop throwing. Repeated measures ANOVAs were used to statistically test significant differences. Results: Handgrip force did not significantly affect the humeroulnar joint gap. The UCL thickness and length and the humeroulnar joint gap were also not different after compared to before repetitive pitching. While higher levels of applied valgus stress significantly increased the humeroulnar joint gap (P < .001), this effect was not significantly different in the interaction with handgrip force and repetitive pitching. Conclusion: The humeroulnar joint gap changes for different levels of elbow valgus stress. However, adult baseball pitchers did not respond to elbow stress after a single pitching sessi, Biomechatronics & Human-Machine Control

An important performance determinant in wheelchair sports is the power exchanged between the athlete-wheelchair combination and the environment, in short, mechanical power. Inertial measurement units (IMUs) might be used to estimate the exchanged mechanical power during wheelchair sports practice. However, to validly apply IMUs for mechanical power assessment in wheelchair sports, a well-founded and unambiguous theoretical framework is required that follows the dynamics of manual wheelchair propulsion. Therefore, this research has two goals. First, to present a theoretical framework that supports the use of IMUs to estimate power output via power balance equations. Second, to demonstrate the use of the IMU-based power estimates during wheelchair propulsion based on experimental data. Mechanical power during straight-line wheelchair propulsion on a treadmill was estimated using a wheel mounted IMU and was subsequently compared to optical motion capture data serving as a reference. IMU-based power was calculated from rolling resistance (estimated from drag tests) and change in kinetic energy (estimated using wheelchair velocity and wheelchair acceleration). The results reveal no significant difference between reference power values and the proposed IMU-based power (1.8% mean difference, N.S.). As the estimated rolling resistance shows a 0.9–1.7% underestimation, over time, IMU-based power will be slightly underestimated as well. To conclude, the theoretical framework and the resulting IMU model seems to provide acceptable estimates of mechanical power during straight-line wheelchair propulsion in wheelchair (sports) practice, and it is an important first step towards feasible power estimations in all wheelchair sports situations., Biomechatronics & Human-Machine Control

Up to 60% of patients experience recurrence after a first traumatic anterior shoulder dislocation (FTASD), which is often defined as having experienced either dislocation or subluxation. Thus surgical intervention after FTASD is worthy of consideration and is guided by the number of patients who need to receive surgical intervention to prevent 1 redislocation (i.e., number needed to treat), (subjective) health benefit, complication risk, and costs. Operative intervention through arthroscopic stabilization can be successful in reducing recurrence risk in FTASD, as has been shown in multiple randomized controlled trials. Nevertheless, there is a large “gray area” for the indication of arthroscopic stabilization, and it is therefore heavily debated which patients should receive operative treatment. Previous trials showed widely varying redislocation rates in both the intervention and control group, meta-analysis shows 2% to 19% after operative and 20% to 75% after nonoperative treatment, and redislocation rates may not correlate with patient-reported outcomes. The literature is quite heterogeneous, and a major confounder is time to follow-up. Furthermore, there is insufficient standardization of reporting of outcomes and no consensus on definition of risk factors. As a result, surgery is a reasonable intervention for FTASD patients, but in which patients it best prevents redislocation requires additional refinement., Biomechatronics & Human-Machine Control

The large stream of data from wearable devices integrated with sports routines has changed the traditional approach to athletes’ training and performance monitoring. However, one of the challenges of data-driven training is to provide actionable insights tailored to individual training optimization. In baseball, the pitching mechanics and pitch type play an essential role in pitchers’ performance and injury risk management. The optimal manipulation of kinematic and temporal parameters within the kinetic chain can improve the pitcher’s chances of success and discourage the batter’s anticipation of a particular pitch type. Therefore, the aim of this study was to provide a machine learning approach to pitch type classification based on pelvis and trunk peak angular velocity and their separation time recorded using wearable sensors (PITCHPERFECT). The Naive Bayes algorithm showed the best performance in the binary classification task and so did Random Forest in the multiclass classification task. The accuracy of Fastball classification was 71%, whilst the accuracy of the classification of three different pitch types was 61.3%. The outcomes of this study demonstrated the potential for the utilization of wearables in baseball pitching. The automatic detection of pitch types based on pelvis and trunk kinematics may provide actionable insight into pitching performance during training for pitchers of various levels of play., Statistics, Biomechanical Engineering, Biomechatronics & Human-Machine Control

In baseball pitchers the elbow is exposed to high and repetitive loads (i.e. external valgus torque), caused by pitching a high number of balls in a practice session or game. This can result in overuse injuries like the ulnar collateral ligament (UCL) injury. To understand injury mechanisms, the effect of repetitive pitching on the elbow load magnitude and variability was investigated. In addition, we explored whether repetitive pitching affects elbow muscle activation during pitching. Fifteen pitchers threw each 60 to 110 balls. The external valgus torque and electromyography of three elbow muscles were quantified during each pitch. Linear mixed model analyses were performed to investigate the effect of repetitive pitching. On a group level, the linear mixed models showed no significant associations of repetitive pitching with valgus torque magnitude and variability and elbow muscle activity. Significant differences exist between pitchers in their individual trajectories in elbow valgus torque and muscle activity with repetitive pitching. This shows the importance of individuality in relation to repetitive pitching. In order to achieve effective elbow injury prevention in baseball pitching, individual characteristics of changes in elbow load and muscle activity in relation to the development of UCL injuries should be investigated., Biomechanical Engineering, Biomechatronics & Human-Machine Control

Purpose: To evaluate the current literature on the effects of anatomic changes caused by the Latarjet procedure and to identify areas for future research. Methods: English-language studies that addressed the consequences of anatomic alterations after the open Latarjet procedure were included. Articles written in languages other than English, reviews, and case reports were excluded. Titles and abstracts were screened by 2 authors. Studies that met the inclusion criteria were screened by the same authors. The following data were extracted from the included studies: authors, year of publication, journal, country of origin, aims or purpose, study population and sample size, methods, procedure, intervention type, and key findings that relate to the scoping review questions. Results: Twenty-two studies were included for analysis, yielding the following findings: First, the Latarjet procedure may change the position of the scapula owing to pectoralis minor tenotomy and/or transfer of the conjoint tendon. Second, dissection of the coracoacromial ligament may result in increased superior translation of the humeral head. The impact of this increased translation on patients’ function remains unclear. Third, the subscapularis split shows, overall, better internal rotation strength compared with subscapularis tenotomy. Fourth, passive external rotation may be limited after capsular repair. Fifth, despite the movement of the conjoint tendon, elbow function seems unchanged. Finally, the musculocutaneous nerve is lengthened with a changed penetration angle into the coracobrachialis muscle, but the clinical impact seems limited. Conclusions: The Latarjet procedure leads to anatomic and biomechanical changes in the shoulder. Areas of future research may include better documentation of scapular movement (bilateral, as well as preoperative and postoperative) and elbow function, the effect of (degenerative) rotator cuff ruptures after the Latarjet procedure on shoulder function, and, Biomechatronics & Human-Machine Control

In wheelchair sports, the use of Inertial Measurement Units (IMUs) has proven to be one of the most accessible ways for ambulatory measurement of wheelchair kinematics. A three-IMU configuration, with one IMU attached to the wheelchair frame and two IMUs on each wheel axle, has previously shown accurate results and is considered optimal for accuracy. Configurations with fewer sensors reduce costs and could enhance usability, but may be less accurate. The aim of this study was to quantify the decline in accuracy for measuring wheelchair kinematics with a stepwise sensor reduction. Ten differently skilled participants performed a series of wheelchair sport specific tests while their performance was simultaneously measured with IMUs and an optical motion capture system which served as reference. Subsequently, both a one-IMU and a two-IMU configuration were validated and the accuracy of the two approaches was compared for linear and angular wheelchair velocity. Results revealed that the one-IMU approach show a mean absolute error (MAE) of 0.10 m/s for absolute linear velocity and a MAE of 8.1°/s for wheelchair angular velocity when compared with the reference system. The two-IMU approach showed similar differences for absolute linear wheelchair velocity (MAE 0.10 m/s), and smaller differences for angular velocity (MAE 3.0°/s). Overall, a lower number of IMUs used in the configuration resulted in a lower accuracy of wheelchair kinematics. Based on the results of this study, choices regarding the number of IMUs can be made depending on the aim, required accuracy and resources available., Biomechanical Engineering, Biomechatronics & Human-Machine Control

Objectives Home-based physiotherapy interventions to improve post-stroke mobility are successful in high-income countries. These programs require less resources compared to center-based programs. However, feasibility of such an intervention in a low and middle-income setting remains unknown. Therefore, the SunRISe (Stroke Rehabilitation In Suriname) study aimed to assess feasibility and preliminary effectiveness of a home-based semi-supervised physiotherapy intervention to promote post-stroke mobility in a low resource setting. Design Prospective randomized controlled trial. Methods Chronic stroke patients were recruited and randomized into either an intervention group (IG (N = 20)) or a control group (CG (N = 10)). The IG received a 3-days-a-week home-based physiotherapy program that was supervised in the first 4 weeks and tele-supervised during the second 4 weeks. The physiotherapy program consisted of walking as well as functional and mobilization exercises. The CG received usual care. Feasibility outcome measures included adherence, patient satisfaction and safety. Efficacy measures included functional exercise tolerance (six-minute walking test (6MWT), functional balance (Berg Balance Score (BBS), upper extremity (UE) function (Disabilities of the Arm, Shoulder and Hand (DASH) Questionnaire), and UE strength ((non-)paretic handgrip (HG) strength). Two-way analysis of variance was used for data analysis. Results Thirty participants (61.8 ± 9.2 years old, 13 men) were enrolled in the study. The intervention was completed by 14 participants (70%). Adherence was affected by rainy season associated infrastructural problems (n = 2), the medical status of participants (n = 3) and insufficient motivation to continue the program without direct supervision (n = 1). No adverse events were noted and participants were satisfied with the program. Functional exercise tolerance (57.2 ± 67.3m, p = 0.02) and UE function (-9.8 ± 15.2, p = 0.04) improved in the IG compared to n, Biomechanical Engineering

Introduction: It is unclear if the collar and cuff treatment improve alignment in displaced surgical neck fractures of the proximal humerus. Therefore, this study evaluated if the neckshaft angle and extent of displacement would improve between trauma and onset of radiographically visible callus in non-operatively treated surgical neck fractures (Boileau type A, B, C). Materials and Methods: A consecutive series of patients (≥ 18 years old) were retrospectively evaluated from a level 1 trauma center in Australia (inclusion period: 2016–2020) and a level 2 trauma center in the Netherlands (inclusion period: 2004 to 2018). Patients were included if they sustained a Boileau-type fracture and underwent initial non-operative treatment. The first radiograph had to be obtained within 24 h after the initial injury and the follow-up radiograph(s) 1 week after trauma and before the start of radiographically visible callus. On each radiograph, the maximal medial gap (MMG), maximal lateral gap (MLG), and neck-shaft angle (NSA) were measured. Linear mixed modelling was performed to evaluate if these measurements would improve over time. Results: Sixty-seven patients were included: 25 type A, 11 type B, and 31 type C fractures. The mean age (range) was 68 years (24–93), and the mean number (range) of follow-up radiographs per patient was 1 (1–4). Linear mixed modelling on both MMG and MLG revealed no improvement during follow-up among the three groups. Mean NSA of type A fractures improved significantly from 161° at trauma to 152° at last follow-up (p-value = 0.004). Conclusions: Apart from humeral head angulation improvement in type A, there is no increase nor reduction in displacement among the three fracture patterns. Therefore, it is advised that surgical decision-making should be performed immediately after trauma. Level of clinical evidence: Level IV, retrospective case series., Biomechanical Engineering

Medial elbow overuse injuries are rising in baseball. The external valgus torque magnitude is a possible risk factor for medial elbow injuries. The magnitude on its own cannot explain why one pitcher sustains an injury and another does not. Therefore, the aim of this study is to describe the within-individual external valgus torque variability and to determine whether the within-individual external valgus torque variability can be described by a Gaussian distribution. Eleven youth elite baseball pitchers threw twenty-five fastball pitches. Body kinematics were measured with VICON motion capture at 400 Hz. Elbow valgus torques of the total 270 pitches were calculated with a custom-made inverse dynamic model in Python. Visual inspection and the Shapiro–Wilk test were performed to test for the within-individual elbow valgus torque normality. The results showed that within-individual valgus torque variability was present in pitchers and differed among pitchers. Furthermore, it was shown that the within-individual valgus torque variability was normally distributed in nine out of eleven subjects. In conclusion, the presence of and differences in within-individual elbow load variability among baseball pitchers can be useful variables as they might be related to overuse elbow injuries., Biomechanical Engineering, Biomechatronics & Human-Machine Control

Background: The aim of this study was to evaluate the thoracohumeral (TH) and glenohumeral (GH) motion with muscle activity after latissimus dorsi transfer (LDT) in a shoulder with a massive irreparable posterosuperior rotator cuff tear (MIRT) and pseudoparalysis compared with the asymptomatic contralateral shoulder (ACS). Methods: We recruited and evaluated 13 patients after LDT in a shoulder with preoperative clinical pseudoparalysis and an MIRT on magnetic resonance imaging, with a minimum follow-up period of 1 year, and with a Hamada stage of 3 or less. Three-dimensional electromagnetic tracking was used to assess shoulder active range of motion in both the LDT shoulder and the ACS. The maximal active elevation of the shoulder (MAES) was assessed and consisted of forward flexion, scapular abduction, and abduction in the coronal plane. Maximal active internal rotation and external rotation were assessed separately. Surface electromyography (EMG) was performed to track activation of the latissimus dorsi (LD) and deltoid muscles during shoulder motion. EMG was scaled to its maximal isometric voluntary contraction recorded in specified strength tests. Results: In MAES, TH motion of the LDT shoulder was not significantly different from that of the ACS (F1,12 = 1.174, P = .300) but the GH contribution was significantly lower in the LDT shoulder for all motions (F1,12 = 11.230, P = .006). External rotation was significantly greater in the ACS (26° ± 10° in LDT shoulder vs. 42° ± 11° in ACS, P < .001). The LD percentage EMG maximum showed no significant difference between the LDT shoulder and ACS during MAES (F1,11 = 0.005, P = .946). During maximal active external rotation of the shoulder, the LDT shoulder showed a higher percentage EMG maximum than the ACS (3.0% ± 2.9% for LDT shoulder vs. 1.2% ± 2.0% for ACS, P = .006). Conclusions: TH motion improved after LDT in an MIRT with pseudoparalysis and was not different from the ACS e, Green Open Access added to TU Delft Institutional Repository 'You share, we take care!' - Taverne project https://www.openaccess.nl/en/you-share-we-take-care Otherwise as indicated in the copyright section: the publisher is the copyright holder of this work and the author uses the Dutch legislation to make this work public., Biomechanical Engineering

More insight into in-field mechanical power in cyclical sports is useful for coaches, sport scientists, and athletes for various reasons. To estimate in-field mechanical power, the use of wearable sensors can be a convenient solution. However, as many model options and approaches for mechanical power estimation using wearable sensors exist, and the optimal combination differs between sports and depends on the intended aim, determining the best setup for a given sport can be challenging. This review aims to provide an overview and discussion of the present methods to estimate in-field mechanical power in different cyclical sports. Overall, in-field mechanical power estimation can be complex, such that methods are often simplified to improve feasibility. For example, for some sports, power meters exist that use the main propulsive force for mechanical power estimation. Another non-invasive method usable for in-field mechanical power estimation is the use of inertial measurement units (IMUs). These wearable sensors can either be used as stand-alone approach or in combination with force sensors. However, every method has consequences for interpretation of power values. Based on the findings of this review, recommendations for mechanical power measurement and interpretation in kayaking, rowing, wheelchair propulsion, speed skating, and cross-country skiing are done., Medical Instruments & Bio-Inspired Technology, Biomechatronics & Human-Machine Control, Biomechanical Engineering

Background: Baseball pitching performance can be mechanically explained by the summation of speed principle and the principle of optimal coordination of partial momenta. Impeding optimal energy generation or transfer by or between the pelvis and trunk segments could provide valuable insight into possible compensation or catch-up mechanisms that may manifest themselves based on these principles. Aim: The aim of the present study was to explore the effects of experimentally impeding the mobility of and between the pelvis and trunk segments (1) on ball speed and mechanical peak joint power, and (2) on mechanical peak load of the elbow and shoulder joints at maximal external rotation (MER) during fastball pitching. Methods: Eleven elite baseball pitchers (mean age 17.4, SD 2.2 years; mean pitching experience 8.9, SD 3.0 years) were instructed to throw at least 15 fastballs as fast and accurately as possible under two conditions. One condition involved impeding the mobility of the pelvis and trunk segments to hamper their ability to rotate independently, which consequently should affect the separation time, defined as the time interval between the pelvis and trunk peak angular velocities. In the other condition, pitchers threw unimpeded. Ball speed, mechanical peak joint power and peak net moment of the elbow and shoulder at MER were compared between conditions using Generalized Estimating Equations (GEE). Results: In the impeded pitching condition, the mean difference of the separation time was 12.4 milliseconds [95% CI (4.0, 20.7)] and for ball speed 0.6 mph [95% CI (0.2, 0.9)] lower compared to the unimpeded condition. Only the peak pelvic angular velocity, in addition to the trunk, upper arm and forearm, was 45 deg/s [95% CI (24, 66)] higher impeded condition. The mean differences of the joint power and net moments at the shoulder and elbow did not reach statistical significance. Conclusion: In elite adolescent baseball, the observed pitching performance after exp, Biomechanical Engineering, Biomechatronics & Human-Machine Control

Monitoring the performance and functional status of baseball pitchers’ upper extremity is important in maintaining the athlete’s health and performance. This study validated a Dutch translation of the original English Kerlan-Jobe Orthopaedic Clinic (KJOC) against the previously validated Disabilities of the Arm, Shoulder and Hand (DASH) and Western Ontario Shoulder Instability Index (WOSI) questionnaires in a group of talented juvenile Dutch baseball pitchers. Three times, from 2014–2016, 107 pitchers completed the Dutch KJOC, DASH and WOSI questionnaires. Participants’ questionnaire scores were analysed for the whole group and the symptomatic player subgroup separately. Internal consistency, construct validity and ceiling and floor effects were examined. Cronbach’s alpha was consistently above 0.8 for the three time periods for the whole group, and ranged between 0.62 and 0.86 for the symptomatic subgroup. Spearman’s rank correlation coefficients ranged from 0.47 to 0.67 for the whole group and 0.32 to 0.99 for the symptomatic subgroup. No floor effects were observed in the scores of the KJOC and only a ceiling effect for the whole group (15.2%) at one time period. The Dutch version of the KJOC has shown acceptable internal consistency and construct validity and can be used to assess overhead athletes’ shoulder and elbow functionality., Biomechatronics & Human-Machine Control

It is generally accepted that most of the energy transferred to the ball during a baseball pitch is generated in the trunk and lower extremities. Therefore, purpose of this study was to assess the energy flow through the lower extremities during a baseball pitch. It was hypothesised that the (stabilising) leading leg mainly transfers energy in a distal-to-proximal order as a kinetic chain while the (driving) trailing leg generates most energy, primarily at the hip. A joint power analysis was used to determine the rates of energy (power) transfer and generation in the ankles, knees, hips and lumbosacral joint (L5-S1) for 22 youth pitchers. Analyses showed that the leading leg mainly transfers energy upwards in a distal-to-proximal order just before stride foot contact. Furthermore, energy generation was higher in the trailing leg and primarily arose from the trailing hip. In conclusion, the legs contribute differently to the energy flow where the leading leg acts as an initial kinetic chain component and the trailing leg drives the pitch by generating energy. The actions of both legs are combined in the pelvis and passed on to the subsequent, more commonly discussed, open kinetic chain starting at L5-S1., Support Biomechanical Engineering, Biomechanical Engineering

Muscle force analysis can be essential for injury risk estimation and performance enhancement in sports like strength training. However, current methods to record muscle forces including electromyography or marker-based measurements combined with a musculoskeletal model are time-consuming and restrict the athlete's natural movement due to equipment attachment. Therefore, the feasibility and validity of a more applicable method, requiring only a single standard camera for the recordings, combined with a deep-learning model and musculoskeletal model is evaluated in the present study during upper-body strength exercises performed by five athletes. Comparison of muscle forces obtained by the single camera driven model against those obtained from a state-of-the art marker-based driven musculoskeletal model revealed strong to excellent correlations and reasonable RMSD's of 0.4–2.1% of the maximum force (Fmax) for prime movers, and weak to strong correlations with RMSD's of 0.4–0.7% Fmax for stabilizing and secondary muscles. In conclusion, a single camera deep-learning driven model is a feasible method for muscle force analysis in a strength training environment, and first validity results show reasonable accuracies, especially for prime mover muscle forces. However, it is evident that future research should investigate this method for a larger sample size and for multiple exercises., Biomechanical Engineering, Biomechatronics & Human-Machine Control

Background: After latissimus dorsi transfer (LDT), an increase in scapulothoracic (ST) contribution in thoracohumeral (TH) elevation is observed when compared to the asymptomatic shoulder. It is not known which shoulder muscles contribute to this change in shoulder kinematics, and whether the timing of muscle recruitment has altered after LDT. The aim of the study was to identify which shoulder muscles and what timing of muscle recruitment are responsible for the increased ST contribution and shoulder elevation after LDT for a massive irreparable posterosuperior rotator cuff tear (MIRT). Methods: Thirteen patients with a preoperative pseudoparalysis and MIRT were recruited after LDT with a minimum follow-up of 1 year. Three-dimensional electromagnetic tracking was used to assess maximum active elevation of the shoulder (MAES) in both the LDT and the asymptomatic contralateral shoulder (ACS). Surface electromyography (EMG) tracked activation (% EMG max) and activation timing of the latissimus dorsi (LD), deltoid, teres major, trapezius (upper, middle and lower) and serratus anterior muscles were collected. MAES was studied in forward flexion, scapular abduction and abduction in the coronal plane. Results: In MAES, no difference in thoracohumeral motion was observed between the LDT and ACS, P = .300. However, the glenohumeral motion for MAES was significantly lower in LDT shoulders F(1,12) = 11.230, P = .006. The LD % EMG max did not differ between the LDT and ACS in MAES. A higher % EMG max was found for the deltoid F(1,12) = 17.241, P = .001, and upper trapezius F(1,10) = 13.612, P = .004 in the LDT shoulder during MAES. The middle trapezius only showed a higher significant difference in % EMG max for scapular abduction, P = .020 (LDT, 52.3 ± 19.4; ACS, 38.1 ± 19.7).The % EMG max of the lower trapezius, serratus anterior and teres major did not show any difference in all movement types between the LDT and ACS and no difference in timing of recruitment of all the, Biomechanical Engineering

Shoulder problems (pain and pathology) are highly prevalent in manual wheelchair users with spinal cord injury. These problems lead to limitations in activities of daily life (ADL), labor- and leisure participation, and increase the health care costs. Shoulder problems are often associated with the long-term reliance on the upper limbs, and the accompanying “shoulder load”. To make an estimation of daily shoulder load, it is crucial to know which ADL are performed and how these are executed in the free-living environment (in terms of magnitude, frequency, and duration). The aim of this study was to develop and validate methodology for the classification of wheelchair related shoulder loading ADL (SL-ADL) from wearable sensor data. Ten able bodied participants equipped with five Shimmer sensors on a wheelchair and upper extremity performed eight relevant SL-ADL. Deep learning networks using bidirectional long short-term memory networks were trained on sensor data (acceleration, gyroscope signals and EMG), using video annotated activities as the target. Overall, the trained algorithm performed well, with an accuracy of 98% and specificity of 99%. When reducing the input for training the network to data from only one sensor, the overall performance decreased to around 80% for all performance measures. The use of only forearm sensor data led to a better performance than the use of the upper arm sensor data. It can be concluded that a generalizable algorithm could be trained by a deep learning network to classify wheelchair related SL-ADL from the wearable sensor data., Biomechanical Engineering

Introduction: It is unclear if the collar and cuff treatment improve alignment in displaced surgical neck fractures of the proximal humerus. Therefore, this study evaluated if the neckshaft angle and extent of displacement would improve between trauma and onset of radiographically visible callus in non-operatively treated surgical neck fractures (Boileau type A, B, C). Materials and Methods: A consecutive series of patients (≥ 18 years old) were retrospectively evaluated from a level 1 trauma center in Australia (inclusion period: 2016–2020) and a level 2 trauma center in the Netherlands (inclusion period: 2004 to 2018). Patients were included if they sustained a Boileau-type fracture and underwent initial non-operative treatment. The first radiograph had to be obtained within 24 h after the initial injury and the follow-up radiograph(s) 1 week after trauma and before the start of radiographically visible callus. On each radiograph, the maximal medial gap (MMG), maximal lateral gap (MLG), and neck-shaft angle (NSA) were measured. Linear mixed modelling was performed to evaluate if these measurements would improve over time. Results: Sixty-seven patients were included: 25 type A, 11 type B, and 31 type C fractures. The mean age (range) was 68 years (24–93), and the mean number (range) of follow-up radiographs per patient was 1 (1–4). Linear mixed modelling on both MMG and MLG revealed no improvement during follow-up among the three groups. Mean NSA of type A fractures improved significantly from 161° at trauma to 152° at last follow-up (p-value = 0.004). Conclusions: Apart from humeral head angulation improvement in type A, there is no increase nor reduction in displacement among the three fracture patterns. Therefore, it is advised that surgical decision-making should be performed immediately after trauma. Level of clinical evidence: Level IV, retrospective case series., Biomechanical Engineering

Medial elbow overuse injuries are rising in baseball. The external valgus torque magnitude is a possible risk factor for medial elbow injuries. The magnitude on its own cannot explain why one pitcher sustains an injury and another does not. Therefore, the aim of this study is to describe the within-individual external valgus torque variability and to determine whether the within-individual external valgus torque variability can be described by a Gaussian distribution. Eleven youth elite baseball pitchers threw twenty-five fastball pitches. Body kinematics were measured with VICON motion capture at 400 Hz. Elbow valgus torques of the total 270 pitches were calculated with a custom-made inverse dynamic model in Python. Visual inspection and the Shapiro–Wilk test were performed to test for the within-individual elbow valgus torque normality. The results showed that within-individual valgus torque variability was present in pitchers and differed among pitchers. Furthermore, it was shown that the within-individual valgus torque variability was normally distributed in nine out of eleven subjects. In conclusion, the presence of and differences in within-individual elbow load variability among baseball pitchers can be useful variables as they might be related to overuse elbow injuries., Biomechanical Engineering, Biomechatronics & Human-Machine Control

Objectives Home-based physiotherapy interventions to improve post-stroke mobility are successful in high-income countries. These programs require less resources compared to center-based programs. However, feasibility of such an intervention in a low and middle-income setting remains unknown. Therefore, the SunRISe (Stroke Rehabilitation In Suriname) study aimed to assess feasibility and preliminary effectiveness of a home-based semi-supervised physiotherapy intervention to promote post-stroke mobility in a low resource setting. Design Prospective randomized controlled trial. Methods Chronic stroke patients were recruited and randomized into either an intervention group (IG (N = 20)) or a control group (CG (N = 10)). The IG received a 3-days-a-week home-based physiotherapy program that was supervised in the first 4 weeks and tele-supervised during the second 4 weeks. The physiotherapy program consisted of walking as well as functional and mobilization exercises. The CG received usual care. Feasibility outcome measures included adherence, patient satisfaction and safety. Efficacy measures included functional exercise tolerance (six-minute walking test (6MWT), functional balance (Berg Balance Score (BBS), upper extremity (UE) function (Disabilities of the Arm, Shoulder and Hand (DASH) Questionnaire), and UE strength ((non-)paretic handgrip (HG) strength). Two-way analysis of variance was used for data analysis. Results Thirty participants (61.8 ± 9.2 years old, 13 men) were enrolled in the study. The intervention was completed by 14 participants (70%). Adherence was affected by rainy season associated infrastructural problems (n = 2), the medical status of participants (n = 3) and insufficient motivation to continue the program without direct supervision (n = 1). No adverse events were noted and participants were satisfied with the program. Functional exercise tolerance (57.2 ± 67.3m, p = 0.02) and UE function (-9.8 ± 15.2, p = 0.04) improved in the IG compared to n, Biomechanical Engineering

In wheelchair sports, the use of Inertial Measurement Units (IMUs) has proven to be one of the most accessible ways for ambulatory measurement of wheelchair kinematics. A three-IMU configuration, with one IMU attached to the wheelchair frame and two IMUs on each wheel axle, has previously shown accurate results and is considered optimal for accuracy. Configurations with fewer sensors reduce costs and could enhance usability, but may be less accurate. The aim of this study was to quantify the decline in accuracy for measuring wheelchair kinematics with a stepwise sensor reduction. Ten differently skilled participants performed a series of wheelchair sport specific tests while their performance was simultaneously measured with IMUs and an optical motion capture system which served as reference. Subsequently, both a one-IMU and a two-IMU configuration were validated and the accuracy of the two approaches was compared for linear and angular wheelchair velocity. Results revealed that the one-IMU approach show a mean absolute error (MAE) of 0.10 m/s for absolute linear velocity and a MAE of 8.1°/s for wheelchair angular velocity when compared with the reference system. The two-IMU approach showed similar differences for absolute linear wheelchair velocity (MAE 0.10 m/s), and smaller differences for angular velocity (MAE 3.0°/s). Overall, a lower number of IMUs used in the configuration resulted in a lower accuracy of wheelchair kinematics. Based on the results of this study, choices regarding the number of IMUs can be made depending on the aim, required accuracy and resources available., Biomechanical Engineering, Biomechatronics & Human-Machine Control

Background: Baseball pitching is associated with a high prevalence of ulnar collateral ligament injuries, potentially due to the high external valgus load on the medial side of the elbow at the instant of maximal shoulder external rotation (MER). In-vitro studies show that external valgus torque is resisted by the ulnar collateral ligament but could also be compensated by elbow muscles. As the potential active contribution of these muscles in counteracting external valgus load during baseball pitching is unknown, the aim of this study is to determine whether and to what extent the elbow muscles are active at and around MER during a fastball pitch in baseball. Methods: Eleven uninjured pitchers threw 15 fastball pitches. Surface electromyography of six muscles crossing the elbow were measured at 2000 Hz. Electromyography signals were normalized to maximal activity values. Co-contraction index (CCI) was calculated between two pairs of the flexor and extensor elbow muscles. Confidence intervals were calculated at the instant of MER. Four ranges of muscle activity were considered; 0–20% was considered low; 21–40% moderate; 41–60% high and over 60% as very high. To determine MER, the pitching motion was captured with a highspeed camera at 240 Hz. Results: The flexor pronator mass, pronator teres, triceps brachii, biceps brachii, extensor supinator mass and anconeus show moderate activity at MER. Considerable variation between participants was found in all muscles. The CCI revealed co-contraction of the two flexor-extensor muscle pairs at MER. Interpretation: The muscle activation of the flexor and pronator muscles at MER indicates a direct contribution of forearm muscles crossing the medial side of the elbow in counteracting the external valgus load during fastball pitching. The activation of both flexor and extensor muscles indicates an in-direct contributory effect as the combined activity of these muscles counteract opening of the humeroulna, Biomechanical Engineering, Biomechatronics & Human-Machine Control

Ball velocity is considered an important performance measure in baseball pitching. Proper pitching mechanics play an important role in both maximising ball velocity and injury-free participation of baseball pitchers. However, an individual pitcher’s characteristics display individuality and may contribute to velocity imparted to the ball. The aim of this study is to predict ball velocity in baseball pitching, such that prediction is tailored to the individual pitcher, and to investigate the added value of the individuality to predictive performance. Twenty-five youth baseball pitchers, members of a national youth baseball team and six baseball academies in The Netherlands, performed ten baseball pitches with maximal effort. The angular velocity of pelvis and trunk were measured with IMU sensors placed on pelvis and sternum, while the ball velocity was measured with a radar gun. We develop three Bayesian regression models with different predictors which were subsequently evaluated based on predictive performance. We found that pitcher’s height adds value to ball velocity prediction based on body segment rotation. The developed method provides a feasible and affordable method for ball velocity prediction in baseball pitching, Statistics, Biomechanical Engineering

In sports, inertial measurement units are often used to measure the orientation of human body segments. A Madgwick (MW) filter can be used to obtain accurate inertial measurement unit (IMU) orientation estimates. This filter combines two different orientation estimates by applying a correction of the (1) gyroscope-based estimate in the direction of the (2) earth frame-based estimate. However, in sports situations that are characterized by relatively large linear accelerations and/or close magnetic sources, such as wheelchair sports, obtaining accurate IMU orientation estimates is challenging. In these situations, applying the MW filter in the regular way, i.e., with the same magnitude of correction at all time frames, may lead to estimation errors. Therefore, in this study, the MW filter was extended with machine learning to distinguish instances in which a small correction magnitude is beneficial from instances in which a large correction magnitude is beneficial, to eventually arrive at accurate body segment orientations in IMU-challenging sports situations. A machine learning algorithm was trained to make this distinction based on raw IMU data. Experiments on wheelchair sports were performed to assess the validity of the extended MW filter, and to compare the extended MW filter with the original MW filter based on comparisons with a motion capture-based reference system. Results indicate that the extended MW filter performs better than the original MW filter in assessing instantaneous trunk inclination (7.6 vs. 11.7° root-mean-squared error, RMSE), especially during the dynamic, IMU-challenging situations with moving athlete and wheelchair. Improvements of up to 45% RMSE were obtained for the extended MW filter compared with the original MW filter. To conclude, the machine learning-based extended MW filter has an acceptable accuracy and performs better than the original MW filter for the assessment of body segment orientation in IMU-challenging sports situation, Biomechanical Engineering, Team Manon Kok

Ulnar collateral ligament (UCL) weakening or tears occur in 16% of professional baseball pitchers. To prevent players from sustaining a UCL injury, it is important to understand the relationship between the UCL properties and elbow stabilizers with the load on the UCL during pitching. In-vitro studies showed that the ultimate external valgus torque of 34 Nm would rupture the UCL, which is in apparent conflict with the reported peak valgus torques in pitching (40–120 Nm). Assuming both observations are correct, the question rises why ‘only’ 16 out of 100 professional pitchers sustain a UCL rupture. Underestimation of the effect of other structures in in-vivo studies is most likely the explanation of this mismatch because the calculated in-vivo torque also includes possible contributions of functional and structural stabilizers. In-vitro studies show that the flexor-pronator mass has the potential to counteract valgus torque directly, whereas the elbow flexor-extensor muscles combined with the humeroradial joint might have an indirect effect on valgus torque by increasing the joint compression force. Accurate experimental electromyography data and a more detailed (musculoskeletal)mechanical model of the elbow are needed to investigate if and to what extent the structural and functional stabilizers can shield the UCL during pitching., Biomechanical Engineering

In sports, inertial measurement units are often used to measure the orientation of human body segments. A Madgwick (MW) filter can be used to obtain accurate inertial measurement unit (IMU) orientation estimates. This filter combines two different orientation estimates by applying a correction of the (1) gyroscope-based estimate in the direction of the (2) earth frame-based estimate. However, in sports situations that are characterized by relatively large linear accelerations and/or close magnetic sources, such as wheelchair sports, obtaining accurate IMU orientation estimates is challenging. In these situations, applying the MW filter in the regular way, i.e., with the same magnitude of correction at all time frames, may lead to estimation errors. Therefore, in this study, the MW filter was extended with machine learning to distinguish instances in which a small correction magnitude is beneficial from instances in which a large correction magnitude is beneficial, to eventually arrive at accurate body segment orientations in IMU-challenging sports situations. A machine learning algorithm was trained to make this distinction based on raw IMU data. Experiments on wheelchair sports were performed to assess the validity of the extended MW filter, and to compare the extended MW filter with the original MW filter based on comparisons with a motion capture-based reference system. Results indicate that the extended MW filter performs better than the original MW filter in assessing instantaneous trunk inclination (7.6 vs. 11.7° root-mean-squared error, RMSE), especially during the dynamic, IMU-challenging situations with moving athlete and wheelchair. Improvements of up to 45% RMSE were obtained for the extended MW filter compared with the original MW filter. To conclude, the machine learning-based extended MW filter has an acceptable accuracy and performs better than the original MW filter for the assessment of body segment orientation in IMU-challenging sports situation, Biomechanical Engineering, Team Manon Kok

Ball velocity is considered an important performance measure in baseball pitching. Proper pitching mechanics play an important role in both maximising ball velocity and injury-free participation of baseball pitchers. However, an individual pitcher’s characteristics display individuality and may contribute to velocity imparted to the ball. The aim of this study is to predict ball velocity in baseball pitching, such that prediction is tailored to the individual pitcher, and to investigate the added value of the individuality to predictive performance. Twenty-five youth baseball pitchers, members of a national youth baseball team and six baseball academies in The Netherlands, performed ten baseball pitches with maximal effort. The angular velocity of pelvis and trunk were measured with IMU sensors placed on pelvis and sternum, while the ball velocity was measured with a radar gun. We develop three Bayesian regression models with different predictors which were subsequently evaluated based on predictive performance. We found that pitcher’s height adds value to ball velocity prediction based on body segment rotation. The developed method provides a feasible and affordable method for ball velocity prediction in baseball pitching, Statistics, Biomechanical Engineering

Background: Baseball pitching is associated with a high prevalence of ulnar collateral ligament injuries, potentially due to the high external valgus load on the medial side of the elbow at the instant of maximal shoulder external rotation (MER). In-vitro studies show that external valgus torque is resisted by the ulnar collateral ligament but could also be compensated by elbow muscles. As the potential active contribution of these muscles in counteracting external valgus load during baseball pitching is unknown, the aim of this study is to determine whether and to what extent the elbow muscles are active at and around MER during a fastball pitch in baseball. Methods: Eleven uninjured pitchers threw 15 fastball pitches. Surface electromyography of six muscles crossing the elbow were measured at 2000 Hz. Electromyography signals were normalized to maximal activity values. Co-contraction index (CCI) was calculated between two pairs of the flexor and extensor elbow muscles. Confidence intervals were calculated at the instant of MER. Four ranges of muscle activity were considered; 0–20% was considered low; 21–40% moderate; 41–60% high and over 60% as very high. To determine MER, the pitching motion was captured with a highspeed camera at 240 Hz. Results: The flexor pronator mass, pronator teres, triceps brachii, biceps brachii, extensor supinator mass and anconeus show moderate activity at MER. Considerable variation between participants was found in all muscles. The CCI revealed co-contraction of the two flexor-extensor muscle pairs at MER. Interpretation: The muscle activation of the flexor and pronator muscles at MER indicates a direct contribution of forearm muscles crossing the medial side of the elbow in counteracting the external valgus load during fastball pitching. The activation of both flexor and extensor muscles indicates an in-direct contributory effect as the combined activity of these muscles counteract opening of the humeroulna, Biomechanical Engineering, Biomechatronics & Human-Machine Control

Ulnar collateral ligament (UCL) weakening or tears occur in 16% of professional baseball pitchers. To prevent players from sustaining a UCL injury, it is important to understand the relationship between the UCL properties and elbow stabilizers with the load on the UCL during pitching. In-vitro studies showed that the ultimate external valgus torque of 34 Nm would rupture the UCL, which is in apparent conflict with the reported peak valgus torques in pitching (40–120 Nm). Assuming both observations are correct, the question rises why ‘only’ 16 out of 100 professional pitchers sustain a UCL rupture. Underestimation of the effect of other structures in in-vivo studies is most likely the explanation of this mismatch because the calculated in-vivo torque also includes possible contributions of functional and structural stabilizers. In-vitro studies show that the flexor-pronator mass has the potential to counteract valgus torque directly, whereas the elbow flexor-extensor muscles combined with the humeroradial joint might have an indirect effect on valgus torque by increasing the joint compression force. Accurate experimental electromyography data and a more detailed (musculoskeletal)mechanical model of the elbow are needed to investigate if and to what extent the structural and functional stabilizers can shield the UCL during pitching., Biomechanical Engineering

Upper extremity injuries are common in baseball. One of these is the ulnar collateral ligament (UCL) injury. In the field of sports injuries, most research focuses on average kinematics and kinetics between subjects, whereas focusing on within-subject variability appears to be more relevant for determining injury risk. We constructed a simple explanatory simulation model to illustrate the relationship between within-subject load variability and risk, illustrating how pitchers with a higher load variability are more likely to sustain an injury compared to pitchers with less load variability. Furthermore, the model comprises the (theoretical) effect of fatigue on load variability and injury threshold over time., Biomechanical Engineering, Biomechatronics & Human-Machine Control

The purpose of the present study was to investigate the effect of an experimentally imposed kinetic chain disturbance in baseball pitching on ball speed and elbow kinetics. The experimental design consisted of two (within-subject) conditions. In one condition there was no manipulation (control condition). The other condition involved a manipulation of the kinetic chain by taping the pelvis and trunk. In both conditions, pitchers were instructed to throw fastballs until a minimum of 15 pitches were captured. Inverse dynamic solutions were used calculate the internal elbow moments of six elite youth baseball pitchers. The pitchers that were hampered in throwing fastballs, by the taped pelvis and trunk, showed significant lower ball speeds and peak internal varus moments compared to the pitchers that were allowed to throw without any hindrance., Biomechanical Engineering

Background: Handrim wheelchair propulsion is often assessed in the laboratory on treadmills (TM) or ergometers (WE), under the assumption that they relate to regular overground (OG) propulsion. However, little is known about the agreement of data obtained from TM, WE, and OG propulsion under standardized conditions. The current study aimed to standardize velocity and power output among these three modalities to consequently compare obtained physiological and biomechanical outcome parameters. Methods: Seventeen able-bodied participants performed two submaximal practice sessions before taking part in a measurement session consisting of 3 × 4 min of submaximal wheelchair propulsion in each of the different modalities. Power output and speed for TM and WE propulsion were matched with OG propulsion, making them (mechanically) as equal as possible. Physiological data and propulsion kinetics were recorded with a spirometer and a 3D measurement wheel, respectively. Results: Agreement among conditions was moderate to good for most outcome variables. However, heart rate was significantly higher in OG propulsion than in the TM condition. Push time and contact angle were smaller and fraction of effective force was higher on the WE when compared to OG/TM propulsion. Participants used a larger cycle time and more negative work per cycle in the OG condition. A continuous analysis using statistical parametric mapping showed a lower torque profile in the start of the push phase for TM propulsion versus OG/WE propulsion. Total force was higher during the start of the push phase for the OG conditions when compared to TM/WE propulsion. Conclusions: Physiological and biomechanical outcomes in general are similar, but possible differences between modalities exist, even after controlling for power output using conventional techniques. Further efforts towards increasing the ecological validity of lab-based equipment is advised and the possible impact of these differences -if at all- in, Biomechanical Engineering

OBJECTIVE: The purpose of this study was to determine the effects of seat height, wheelchair mass and grip on mobility performance among wheelchair basketball players and to investigate whether these effects differ between classification levels. METHODS: Elite wheelchair basketball players with a low (n= 11, class 1 or 1.5) or high (n= 10, class 4 or 4.5) classification performed a field-based wheelchair mobility performance (WMP) test. Athletes performed the test six times in their own wheelchair, of which five times with different configurations, a higher or lower seat height, with additional distally or centrally located extra mass, and with gloves. The effects of these configurations on performance times and the interaction with classification were determined. RESULTS: Total performance time on the WMP test was significantly reduced when using a 7.5% lower seat height. Additional mass (7.5%) and glove use did not lead to changes in performance time. Effects were the same for the two classification levels. CONCLUSIONS: The methodology can be used in a wheelchair fitting process to search for the optimal individual configuration to enhance mobility performance. Out of all adjustments possible, this study focused on seat height, mass and grip only. Further research can focus on these possible adjustments to optimize mobility performance in wheelchair basketball., Accepted Author Manuscript, Biomechatronics & Human-Machine Control, Biomechanical Engineering

Athlete impairment level is an important factor in wheelchair mobility performance (WMP) in sports. Classification systems, aimed to compensate impairment level effects on performance, vary between sports. Improved understanding of resemblances and differences in WMP between sports could aid in optimizing the classification methodology. Furthermore, increased performance insight could be applied in training and wheelchair optimization. The wearable sensor-based wheelchair mobility performance monitor (WMPM) was used to measure WMP of wheelchair basketball, rugby and tennis athletes of (inter-)national level during match-play. As hypothesized, wheelchair basketball athletes show the highest average WMP levels and wheelchair rugby the lowest, whereas wheelchair tennis athletes range in between for most outcomes. Based on WMP profiles, wheelchair basketball requires the highest performance intensity, whereas in wheelchair tennis, maneuverability is the key performance factor. In wheelchair rugby, WMP levels show the highest variation comparable to the high variation in athletes’ impairment levels. These insights could be used to direct classification and training guidelines, with more emphasis on intensity for wheelchair basketball, focus on maneuverability for wheelchair tennis and impairment-level based training programs for wheelchair rugby. Wearable technology use seems a prerequisite for further development of wheelchair sports, on the sports level (classification) and on individual level (training and wheelchair configuration)., Research Funding National, Biomechanical Engineering

The use of a manual wheelchair is critical to 1% of the world's population. Human powered wheeled mobility research has considerably matured, which has led to improved research techniques becoming available over the last decades. To increase the understanding of wheeled mobility performance, monitoring, training, skill acquisition, and optimization of the wheelchair-user interface in rehabilitation, daily life, and sports, further standardization of measurement set-ups and analyses is required. A crucial stepping-stone is the accurate measurement and standardization of external power output (measured in Watts), which is pivotal for the interpretation and comparison of experiments aiming to improve rehabilitation practice, activities of daily living, and adaptive sports. The different methodologies and advantages of accurate power output determination during overground, treadmill, and ergometer-based testing are presented and discussed in detail. Overground propulsion provides the most externally valid mode for testing, but standardization can be troublesome. Treadmill propulsion is mechanically similar to overground propulsion, but turning and accelerating is not possible. An ergometer is the most constrained and standardization is relatively easy. The goal is to stimulate good practice and standardization to facilitate the further development of theory and its application among research facilities and applied clinical and sports sciences around the world., Biomechanical Engineering

The measurement of handrim wheelchair propulsion characteristics and performance in the field is complicated due to the non-stationary nature of wheelchair driving. In contrast, the laboratory provides a constrained and standardisable environment to conduct measurements and experiments. Apart from wheelchair treadmills, dynamometers or ergometers for handrim wheelchairs are often custom-made, one-of-a-kind, expensive, and sparsely documented in the research literature. To facilitate standardised and comparable lab-based measurements in research, as well as in clinical settings and adapted sports, a new wheelchair ergometer was developed. The ergometer with instrumented dual rollers allows for the performance analysis of individuals in their personal handrim wheelchair and facilitates capacity assessment, training and skill acquisition in rehabilitation or adapted sports. The ergometer contains two servomotors, one for each rear wheel roller, that allow for the simulation of translational inertia and resistive forces as encountered during wheelchair propulsion based on force input and a simple mechanical model of wheelchair propulsion. A load cell configuration for left and right roller enables the measurement of effective user-generated torque and force on the handrim and the concomitant timing patterns. Preliminary results are discussed., Accepted Author Manuscript, Biomechanical Engineering

There are many ways to simulate handrim wheelchair propulsion in the laboratory. Ideally, these would be able to, at least mechanically, simulate field conditions. This narrative review provides an overview of the lab-based equipment used in published research and critically assesses their ability to simulate and measure wheelchair propulsion performance. A close connection to the field can only be achieved if the instrument can adequately simulate frictional losses and inertia of real-life handrim wheelchair propulsion, while maintaining the ergonomic properties of the wheelchair-user interface. Lab-based testing is either performed on a treadmill or a wheelchair ergometer (WCE). For this study WCEs were divided into three categories: roller, flywheel, and integrated ergometers. In general, treadmills are mechanically realistic, but cannot simulate air drag and acceleration tasks cannot be performed; roller ergometers allow the use of the personal wheelchair, but calibration can be troublesome; flywheel ergometers can be built with commercially-available parts, but inertia is fixed and the personal wheelchair cannot be used; integrated ergometers do not employ the personal wheelchair, but are suited for the implementation of different simulation models and detailed measurements. Lab-based equipment is heterogeneous and there appears to be little consensus on how to simulate field conditions., Biomechanical Engineering

The purpose of the present study was to investigate the effect of an experimentally imposed kinetic chain disturbance in baseball pitching on ball speed and elbow kinetics. The experimental design consisted of two (within-subject) conditions. In one condition there was no manipulation (control condition). The other condition involved a manipulation of the kinetic chain by taping the pelvis and trunk. In both conditions, pitchers were instructed to throw fastballs until a minimum of 15 pitches were captured. Inverse dynamic solutions were used calculate the internal elbow moments of six elite youth baseball pitchers. The pitchers that were hampered in throwing fastballs, by the taped pelvis and trunk, showed significant lower ball speeds and peak internal varus moments compared to the pitchers that were allowed to throw without any hindrance., Biomechanical Engineering

Upper extremity injuries are common in baseball. One of these is the ulnar collateral ligament (UCL) injury. In the field of sports injuries, most research focuses on average kinematics and kinetics between subjects, whereas focusing on within-subject variability appears to be more relevant for determining injury risk. We constructed a simple explanatory simulation model to illustrate the relationship between within-subject load variability and risk, illustrating how pitchers with a higher load variability are more likely to sustain an injury compared to pitchers with less load variability. Furthermore, the model comprises the (theoretical) effect of fatigue on load variability and injury threshold over time., Biomechanical Engineering, Biomechatronics & Human-Machine Control

Background: Handrim wheelchair propulsion is often assessed in the laboratory on treadmills (TM) or ergometers (WE), under the assumption that they relate to regular overground (OG) propulsion. However, little is known about the agreement of data obtained from TM, WE, and OG propulsion under standardized conditions. The current study aimed to standardize velocity and power output among these three modalities to consequently compare obtained physiological and biomechanical outcome parameters. Methods: Seventeen able-bodied participants performed two submaximal practice sessions before taking part in a measurement session consisting of 3 × 4 min of submaximal wheelchair propulsion in each of the different modalities. Power output and speed for TM and WE propulsion were matched with OG propulsion, making them (mechanically) as equal as possible. Physiological data and propulsion kinetics were recorded with a spirometer and a 3D measurement wheel, respectively. Results: Agreement among conditions was moderate to good for most outcome variables. However, heart rate was significantly higher in OG propulsion than in the TM condition. Push time and contact angle were smaller and fraction of effective force was higher on the WE when compared to OG/TM propulsion. Participants used a larger cycle time and more negative work per cycle in the OG condition. A continuous analysis using statistical parametric mapping showed a lower torque profile in the start of the push phase for TM propulsion versus OG/WE propulsion. Total force was higher during the start of the push phase for the OG conditions when compared to TM/WE propulsion. Conclusions: Physiological and biomechanical outcomes in general are similar, but possible differences between modalities exist, even after controlling for power output using conventional techniques. Further efforts towards increasing the ecological validity of lab-based equipment is advised and the possible impact of these differences -if at all- in, Biomechanical Engineering

OBJECTIVE: The purpose of this study was to determine the effects of seat height, wheelchair mass and grip on mobility performance among wheelchair basketball players and to investigate whether these effects differ between classification levels. METHODS: Elite wheelchair basketball players with a low (n= 11, class 1 or 1.5) or high (n= 10, class 4 or 4.5) classification performed a field-based wheelchair mobility performance (WMP) test. Athletes performed the test six times in their own wheelchair, of which five times with different configurations, a higher or lower seat height, with additional distally or centrally located extra mass, and with gloves. The effects of these configurations on performance times and the interaction with classification were determined. RESULTS: Total performance time on the WMP test was significantly reduced when using a 7.5% lower seat height. Additional mass (7.5%) and glove use did not lead to changes in performance time. Effects were the same for the two classification levels. CONCLUSIONS: The methodology can be used in a wheelchair fitting process to search for the optimal individual configuration to enhance mobility performance. Out of all adjustments possible, this study focused on seat height, mass and grip only. Further research can focus on these possible adjustments to optimize mobility performance in wheelchair basketball., Accepted Author Manuscript, Biomechatronics & Human-Machine Control, Biomechanical Engineering

Athlete impairment level is an important factor in wheelchair mobility performance (WMP) in sports. Classification systems, aimed to compensate impairment level effects on performance, vary between sports. Improved understanding of resemblances and differences in WMP between sports could aid in optimizing the classification methodology. Furthermore, increased performance insight could be applied in training and wheelchair optimization. The wearable sensor-based wheelchair mobility performance monitor (WMPM) was used to measure WMP of wheelchair basketball, rugby and tennis athletes of (inter-)national level during match-play. As hypothesized, wheelchair basketball athletes show the highest average WMP levels and wheelchair rugby the lowest, whereas wheelchair tennis athletes range in between for most outcomes. Based on WMP profiles, wheelchair basketball requires the highest performance intensity, whereas in wheelchair tennis, maneuverability is the key performance factor. In wheelchair rugby, WMP levels show the highest variation comparable to the high variation in athletes’ impairment levels. These insights could be used to direct classification and training guidelines, with more emphasis on intensity for wheelchair basketball, focus on maneuverability for wheelchair tennis and impairment-level based training programs for wheelchair rugby. Wearable technology use seems a prerequisite for further development of wheelchair sports, on the sports level (classification) and on individual level (training and wheelchair configuration)., Research Funding National, Biomechanical Engineering

The measurement of handrim wheelchair propulsion characteristics and performance in the field is complicated due to the non-stationary nature of wheelchair driving. In contrast, the laboratory provides a constrained and standardisable environment to conduct measurements and experiments. Apart from wheelchair treadmills, dynamometers or ergometers for handrim wheelchairs are often custom-made, one-of-a-kind, expensive, and sparsely documented in the research literature. To facilitate standardised and comparable lab-based measurements in research, as well as in clinical settings and adapted sports, a new wheelchair ergometer was developed. The ergometer with instrumented dual rollers allows for the performance analysis of individuals in their personal handrim wheelchair and facilitates capacity assessment, training and skill acquisition in rehabilitation or adapted sports. The ergometer contains two servomotors, one for each rear wheel roller, that allow for the simulation of translational inertia and resistive forces as encountered during wheelchair propulsion based on force input and a simple mechanical model of wheelchair propulsion. A load cell configuration for left and right roller enables the measurement of effective user-generated torque and force on the handrim and the concomitant timing patterns. Preliminary results are discussed., Accepted Author Manuscript, Biomechanical Engineering

There are many ways to simulate handrim wheelchair propulsion in the laboratory. Ideally, these would be able to, at least mechanically, simulate field conditions. This narrative review provides an overview of the lab-based equipment used in published research and critically assesses their ability to simulate and measure wheelchair propulsion performance. A close connection to the field can only be achieved if the instrument can adequately simulate frictional losses and inertia of real-life handrim wheelchair propulsion, while maintaining the ergonomic properties of the wheelchair-user interface. Lab-based testing is either performed on a treadmill or a wheelchair ergometer (WCE). For this study WCEs were divided into three categories: roller, flywheel, and integrated ergometers. In general, treadmills are mechanically realistic, but cannot simulate air drag and acceleration tasks cannot be performed; roller ergometers allow the use of the personal wheelchair, but calibration can be troublesome; flywheel ergometers can be built with commercially-available parts, but inertia is fixed and the personal wheelchair cannot be used; integrated ergometers do not employ the personal wheelchair, but are suited for the implementation of different simulation models and detailed measurements. Lab-based equipment is heterogeneous and there appears to be little consensus on how to simulate field conditions., Biomechanical Engineering

The use of a manual wheelchair is critical to 1% of the world's population. Human powered wheeled mobility research has considerably matured, which has led to improved research techniques becoming available over the last decades. To increase the understanding of wheeled mobility performance, monitoring, training, skill acquisition, and optimization of the wheelchair-user interface in rehabilitation, daily life, and sports, further standardization of measurement set-ups and analyses is required. A crucial stepping-stone is the accurate measurement and standardization of external power output (measured in Watts), which is pivotal for the interpretation and comparison of experiments aiming to improve rehabilitation practice, activities of daily living, and adaptive sports. The different methodologies and advantages of accurate power output determination during overground, treadmill, and ergometer-based testing are presented and discussed in detail. Overground propulsion provides the most externally valid mode for testing, but standardization can be troublesome. Treadmill propulsion is mechanically similar to overground propulsion, but turning and accelerating is not possible. An ergometer is the most constrained and standardization is relatively easy. The goal is to stimulate good practice and standardization to facilitate the further development of theory and its application among research facilities and applied clinical and sports sciences around the world., Biomechanical Engineering

Speed skates are the most important part of equipment of a speed skater, where weight, rocker and bend are just a few characteristics that are to a high degree individualized. This poses a challenge for any type of research in speed skating where forces have to be measured in a reliable manner. For this purpose, a 5 degrees of freedom (DoF) instrumented speed skate (VU-Skate) has been designed and validated, weighing only 130 gram extra. Skaters use their own blades and shoes, something skaters are very keen on. A calibration tool has been developed to calibrate the 5 DoF. The quality of the data has been validated in 2 ways: 1. With the use of force plates and 2. By comparing the signals to another (also newly developed) Ultra-light Forces sensor. The results are remarkably good. This is the first step in being able to measure power continuously during each stroke., Biomechatronics & Human-Machine Control, Biomechanical Engineering

Understanding the biomechanics of the drag-flick is important for refining the performance of this task in field hockey. The aim of this study was to determine whether the maximal knee angle and maximal angular velocity of the lead knee extension are associated with ball speed in elite drag-flick players. The kinematics of the drag flick was studied in 19 elite field-hockey players who performed 15 drag-flick shots each towards a target located 1.30 m high at optimal speed. A motion capture suit was used to capture full body drag-flick behaviour sampling at 240 Hz. Multiple regression analyses were used to study the association between both the maximal knee flexion angle and maximal angular velocity of the leading knee extension and ball speed. Significant positive associations were found between knee extension velocity and ball speed (R2 =.127, p <.001). A higher knee extension velocity resulted in higher ball speeds within the individual, without negatively affecting the accuracy. It is advised to train, within an elite drag-flick group, for higher knee extension speed to improve the drag-flick performance. Whether training to improve this parameter results in higher ball speeds should be subject of future studies., Biomechanical Engineering, Biomechatronics & Human-Machine Control, (OLD) CRE Building & Installations