Search

The purpose of this study is to clarify the porcelain firing temperature conditions that give strongest bonding strength of porcelain to zirconia to manufacture all-ceramic fixed dental prostheses (FDPs) with excellent long-term stability.Opaque porcelain samples (8.0 × 3.0 × 1.2 mm) were placed in the center of zirconia plates (25.0 × 3.0 × 0.5 mm) and fired at temperatures of 950°C, 1,050°C, 1,100°C, and 1,150°C. Schwickerath crack initiation tests, elemental analyses, and morphological changes of the samples were compared.There was no difference in the bonding strength among all the groups of porcelain fired at different temperatures. Elemental analysis of Si and OIt is suggested that silicon is also involved in chemical bonds due to firing at high temperatures.

Purpose To perform an international survey on current practices in imaging-based surveillance, diagnosis, staging, and assessment of treatment response for HCC. Materials and methods Three themes were covered in this international survey: demographics of respondents and liver imaging expertise; imaging practices for screening, surveillance, diagnosis, staging, and assessment of treatment response for HCC; and diagnostic imaging systems used. Descriptive summaries were created. Results Of 151 respondents, 22.5% were from Asia, 6.0% from Europe, 19.9% from North America, 26.5% from South America, and 25.2% from Australasia; 57.0% respondents worked in academic and 34.4% in private or mixed settings. Non-contrast ultrasound was most commonly used for screening and surveillance of HCC (90.7%), and multiphase computed tomography was used for diagnosis (96.0%). Extracellular contrast agents (69.5%) were the most commonly used MRI contrast agents and Lumason/SonoVue (31.1%) is the most commonly used contrast-enhanced ultrasound contrast agent. A majority (94.0%) of respondents use ancillary imaging features for assessment of liver lesions in at-risk patients. Usage of diagnostic imaging systems for HCC varied by region. RECIST or mRECIST criteria were most commonly used for assessing HCC treatment response (48.3%). Most respondents agreed that a standardized classification for the diagnosis of HCC is needed (68.9%) and that an atlas and lexicon would help improve inter-reader agreement (71.5%). Conclusion Practices and recommendations for imaging of HCC vary between geographical regions. Future efforts to develop a unified system should address regional differences and potential barriers for adoption of a standardized diagnostic system for HCC.

The aim of this study was to investigate histologically the amount of peri-implant tissue augmentation after volume-stable porcine collagen matrix transplantation. Six male beagle dogs were used in the experiment. P2, P4, and M1 distal roots were extracted under general anesthesia. After 6 months, implants were placed in the same sites, and volume-stable porcine collagen matrix transplantation was performed. Impressions were taken at 1 and 2 weeks and at 1, 2, and 3 months after transplantation. The dogs were euthanized at 3 months, and their mandibles were removed and scanned using micro-computed tomography. Standard Triangulated Language data were also obtained. Using preoperative models as a reference, the data for all time points were compared, and changes in the thickness of the cross-section of the implant sites were measured. The model created at 3 months was then compared with the mandible data, and the thickness of collected peri-implant soft tissue was measured under optical microscopy. Increased thickness was found at some of the sites on the buccal side. Regarding the peri-implant soft tissue, the thickness of the measured sites on the buccal side was significantly increased at 3 months in the experimental group. Histological observations of the internal structures of the tissue in the experimental group revealed irregular collagen fibers and a remnant collagen matrix. Endogenous tissue was observed within the collagen matrix, indicating good fusion with the surrounding autologous tissue. These results suggest that volume-stable porcine collagen matrix transplantation promotes peri-implant tissue augmentation on the buccal side.

Purpose: To assess the utility of measurement of the computed tomography (CT) attenuation value (CTav) in predicting tumor necrosis in hepatocellular carcinoma (HCC) patients who achieve a complete response (CR), defined using modified Response Evaluation Criteria in Solid Tumors (mRECIST), after lenvatinib treatment. Method: We compared CTav in arterial phase CT images with postoperative histopathology in four patients who underwent HCC resection after lenvatinib treatment, to determine CTav thresholds indicative of histological necrosis (N-CTav). Next, we confirmed the accuracy of the determined N-CTav in 15 cases with histopathologically proven necrosis in surgical specimens. Furthermore, the percentage of the tumor with N-CTav, i.e. the N-CTav occupancy rate, assessed using Image J software in 30 tumors in 12 patients with CR out of 571 HCC patients treated with lenvatinib, and its correlation with local recurrence following CR were examined. Results: Receiver operating characteristic (ROC) curve analysis revealed an optimal cut-off value of CTav of 30.2 HU, with 90.0% specificity and 65.0% sensitivity in discriminating between pathologically identified necrosis and degeneration, with a CTav of less than 30.2 HU indicating necrosis after lenvatinib treatment (N30-CTav). Furthermore, the optimal cut-off value of 30.6% for the N30-CTav occupancy rate by ROC analysis was a significant indicator of local recurrence following CR with 76.9% specificity and sensitivity (area under the ROC curve; 0.939), with the CR group with high N30-CTav occupancy (>30.6%) after lenvatinib treatment showing significantly lower local recurrence (8.3% at 1 year) compared with the low (30.6% might be a predictor of maintenance of CR. Use of these indicators have the potential to impact systemic chemotherapy for HCC.

Purpose The purpose of this study was to compare the marginal and internal fit of three-unit fixed dental prostheses (FDPs) fabricated using CAD/CAM with two designs, two cement space (CS), and two zirconia types. Methods A master model with two zirconia abutments and a missing tooth was scanned with an intraoral scanner. FDPs were fabricated with two designs (Full contour: FC, Framework: FW), two zirconia types (multi-layer: L, single-layer: W), and two CS values (30 and 45 μm for L and 30 μm for W). There were six experimental groups. The fit of the FDPs was evaluated using the replica method. The space between an abutment and the FDPs in the marginal (MO), chamfer (CH), axial (AX), and occlusal (OC) areas was measured under an optical microscope and the data was statistically analyzed using three-way ANOVA and Bonferroni test (p Results FW- l -45 μm showed a significantly smaller space than those for the FC in MO (p = 0.011), CH (p = 0.001) and AXE (p = 0.003). FW- l -30 μm showed a significantly smaller space than that for the 45 µm in AXE (p = 0.000) and OC (p = 0.016). FW-W-30 µm showed a significantly smaller space than that for the L in MO (p = 0.000), CH (p = 0.000), AXE (p = 0.000), and OC (p = 0.002). Conclusions The design and CS of the FDPs affected the fit. FDPs with single-layer zirconia showed better fit than that obtained with multi-layer zirconia.

The purpose of this study is to investigate, in vitro, how two different implant placement methods (one and two-stage implant placement) affect implant surface temperature after thermal stimulation. Two titanium screw implants were used and three thermocouples were attached to the implant surface at 0.5 mm (ch1), 5.5 mm (ch2) and 9.0 mm (ch3) under each platform. Experimental devices were fabricated pouring polymerization resin under a condition that imitated the two embedded technique with the one-stage implant placement model (1-stage) and the two-stage implant placement model (2-stage). A hot water storage device was installed in each model and hot water at three temperatures (60 °C, 70 °C and 100 °C) was flowed. The temperature change over time at the implant surface by the thermocouple was recorded. From the measurement data, the maximum temperature (Max-temp) at the implant surface, the time to reach 47 °C (47 °C r-time), and the duration of 47 °C or more (47 °C c-time) were calculated, and the test was repeated 26 times using the same method. The mean of repeated measurements was determined and statistical analysis was performed. Max-temp showed significant differences between each implant placement method, each channel and each thermal stimulation (p

Sinus floor augmentation (SFA) is the most predictable treatment option in the atrophic posterior maxilla. However, exposure of the apical implant body into the maxillary sinus cavity is an occasionally observed phenomenon after SFA. Although most penetrating dental implants remain completely asymptomatic, they may induce recurrent rhinosinusitis or implant loss. Removal of the implant should be considered if there is significant implant exposure that results in prolonged treatment and increased costs. This case report demonstrates a recovery approach using sinus floor reaugmentation without implant removal in a patient with an apically exposed implant into the maxillary sinus cavity.

The purpose of this study was to investigate how differences in dental implant and screw materials affected screw loosening. Screws (pure titanium; Ti4S, titanium alloy; TiAS), blocks (Y-TZP; ZrB, pure titanium; Ti4B) and plates (Y-TZP; ZrP), representing abutment screws, implant bodies and superstructures, respectably, were used. Plates were fastened to blocks by screws using a torque of 20 N•cm, and the loosening torque was measured after cyclic loading. Tests was performed on 13 specimens per group, with four groups for loading at the eccentric point (9 mm from screw center) and one group at the centric point (3 mm from screw center). In eccentric point tests, Ti4S screws led to significantly more loosening than TiAS screws (p

The purpose of this study is to investigate the effects of porcelain veneering methods on the marginal and internal fit of a three-unit zirconia framework. A zirconia master model, in which the lower-left second premolar and the second left molar were used as the abutment, was obtained using an intraoral scanner. Based on the data, three-unit zirconia frameworks for fabricating all-ceramic bridges were designed and milled (FW group). Two types of all-ceramic bridge were fabricated by veneering porcelain onto these frameworks using the press-over technique (P group) and the layering technique (L group). The replica technique was used to measure the gap size between the abutments and the bridges. Measurements were taken in the marginal opening area (MO), chamfer area (CH), axial area (AX), and occlusal area (OC). Statistical analysis was performed using the Mann–Whitney U-test. There was no significant difference in MO and CH between the P and L groups. However, in AX, the L group had a significantly larger gap size than that of the P group (p = 0.003). In addition, compared with the FW group, the P group showed a significantly larger gap size in MO (p

The torsional fracture strength at the interface between a base plate and veneering material was evaluated for three kinds of veneered restoration: porcelain fused to zirconia (PFZ), porcelain fused to metal (PFM), and composite resin veneered metal (CRVM). The metal and zirconia base plate (30×4×0.4 mm) were prepared and these plates were veneered as test specimens using each material to a total thickness of 1.2 mm. Torsional force was applied to each specimen using a rotational speed of 1.0 deg/min until the veneering material underwent fracture or exfoliation. The torsional fracture values were measured and the data were statistically analyzed using one-way ANOVA. The torsional fracture strength for PFZ, PFM, and CRVM was 3.0, 3.1, and 11.1 N•cm, respectively.

AIM To verify the utility of the 2-in-1-out-compartment model analysis (CMA) of intravenous contrast-enhanced dynamic computed tomography (IV-CT) for evaluating hepatic arterial and portal venous flow using intra-arterial contrast-enhanced CT (IA-CT). METHODS We retrospectively evaluated 49 consecutive patients who underwent IV-CT and were radiologically or histologically diagnosed as having hepatic malignant lesion (51 classical hepatocellular carcinomas [HCC], 4 early HCC, 3 cholangiolocellular carcinomas, 1 mixed HCC, 3 cholangiocellular carcinomas). As a gold standard for hepatic arterial and portal blood flows, we defined the normalized enhancement in CT values on CTAP (nCTAP) and CTHA (nCTHA). The hepatic arterial (k1a ) and portal venous inflow velocity (k1p ) constants in hepatic lesions and surrounding liver parenchyma were obtained from the CMA of IV-CT with various outflow velocity constant (k2 ) limits using the nonlinear least square method. The correlation coefficient between the normalized enhancement in IA-CT and CMA of IV-CT was statistically evaluated according to various k2 limits. RESULTS The highest mean correlation coefficient between k1a and nCTHA (r = 0.65, P

AIM The purpose of this study was to determine whether the liver stiffness (LS) measured on magnetic resonance (MR) elastography can be estimated by a combination of gadoxetate disodium-enhanced MR imaging (EOB-MRI) and ordinary blood tests. METHODS We evaluated 33 consecutive patients with suspected liver disease who underwent EOB-MRI using a Differential Subsampling with Cartesian Ordering MR sequence and MR elastography using a 1.5-T MR system in this prospective study. A stepwise multiple linear regression model analysis of LS was performed using various predictive values obtained from two-in-one-uptake, two-compartment model analysis of EOB-MRI (velocity constants of arterial inflow [K1a ], portal venous inflow [K1p ], hepatocellular uptake [Ki ]), and ordinary blood test results (blood platelet count, serum albumin level [ALB], total serum bilirubin level [T-BIL], and prothrombin time [PT%]). RESULTS Multiple linear regression model analysis revealed that hepatic perfusion-uptake index (HPUI = -K1a + K1p + Ki ) (P 5.0 kPa) and lower (LS