Search

The use of weightlifting exercises is prevalent in competitive and recreational environments, as well as sport-specific training. Traditionally, weightlifting coaches prescribe specific training loads based on an individual's maximal ability. Velocity-based training offers an alternative method that promises to quantify strength based on velocity and provides information that increases competitiveness through real-time feedback. Various velocity measurement devices are available on the market. Their precision is critical for the adequate implementation of velocity-based training. The aim of the present study was to compare the concentric peak velocity measurements of five of these devices during two weightlifting movements, the snatch and clean, to data collected with a 12-camera motion capture system, which was considered as gold standard. It was hypothesized that the velocity measurement devices used in this study would vary in accuracy based on their retail prices. Velocity readings associated with light and moderate (40% and 70% of one-repetition max) loads were measured for both the snatch and clean performed by 12 competitive weightlifters. A least products regression was used to assess validity by comparing five devices against a criterion measure. A general linear model showed statistical differences in the velocities measured with these five devices (p < 0.001). Specifically, the GymAware RS linear position transducer was the most accurate device, demonstrating no fixed or proportional bias when used to quantify velocity during the snatch and clean. The remaining four devices significantly underestimated peak velocity, which would directly impact the daily planning of lifters' training. Practitioners must consider the error and bias of each device before implementing velocity-based training. [ABSTRACT FROM AUTHOR]

Change of direction, stops, and pivots are among the most common non-contact movements associated with anterior cruciate ligament (ACL) injuries in soccer. By observing these dynamic movements, clinicians recognize abnormal kinematic patterns that contribute to ACL tears such as increased knee valgus or reduced knee flexion. Different motions and physical demands are observed across playing positions, which may result in varied lower limb kinematic patterns. In the present study, 28 college and sub-elite soccer players performed four dynamic motions (change of direction with and without ball, header, and instep kick) with the goal of examining the effect of on-field positioning, leg dominance, and gender in lower body kinematics. Motion capture software monitored joint angles in the knee, hip, and ankle. A three-way ANOVA showed significant differences in each category. Remarkably, centrally positioned players displayed significantly greater knee adduction (5° difference, p = 0.013), hip flexion (9° difference, p = 0.034), hip adduction (7° difference, p = 0.016), and dorsiflexion (12° difference, p = 0.022) when performing the instep kick in comparison to their laterally positioned counterparts. These findings suggest that central players tend to exhibit a greater range of motion when performing an instep kicking task compared to laterally positioned players. At a competitive level, this discrepancy could potentially lead to differences in lower limb muscle development among on-field positions. Accordingly, it is suggested to implement position-specific prevention programs to address these asymmetries in lower limb kinematics, which can help mitigate dangerous kinematic patterns and consequently reduce the risk of ACL injury in soccer players. [ABSTRACT FROM AUTHOR]

Damage to the meniscus has been associated with excessive shear loads. Aimed at elucidating meniscus pathophysiology, previous studies have investigated the shear properties of the meniscus fibrocartilaginous core. However, the meniscus is structurally inhomogeneous, with an external cartilaginous envelope (tibial and femoral surface layers) wrapping the tissue core. To date, little is known about the shear behavior of the surface layers. The objective of this study was to measure the dynamic shear properties of the surface layers and derive empirical relations with their composition. Specimens were harvested from tibial and femoral surface layers and core of porcine menisci (medial and lateral, n = 10 each). Frequency sweep tests yielded complex shear modulus (G*) and phase shifts (δ). Mechanical behavior of regions was described by a generalized Maxwell model. Correlations between shear moduli with water and glycosaminoglycans content of the tissue regions were investigated. The femoral surface had the lowest shear modulus, when compared to core and tibial regions. A 3‐relaxation times Maxwell model satisfactorily interpreted the shear behavior of all tissue regions. Inhomogeneous tissue composition was also observed, with water content in the surface layers being higher when compared with tissue core. Water content negatively correlated with shear properties in all regions. The lower measured shear properties in the femoral layer may explain the higher prevalence of meniscal tears on the superior surface of the tissue. The heterogenous behavior of the tissue in shear provides insight into meniscus pathology and has important implications for efforts to tissue engineer replacement tissues. [ABSTRACT FROM AUTHOR]

The intervertebral disk (IVD), characterized as a charged, hydrated soft tissue, is the largest avascular structure in the body. Mechanical loading to the disk results in electromechanical transduction phenomenon as well as altered transport properties. Electrical conductivity is a material property of tissue depending on ion concentrations and diffusivities, which are in turn functions of tissue composition and structure. The aim of this study was to investigate the effect of mechanical loading on electrical behavior in human IVD tissues. We hypothesized that electrical conductivity in human IVD is strain-dependent, due to change in tissue composition caused by compression, and inhomogeneous, due to tissue structure and composition. We also hypothesized that conductivity in human annulus fibrosus (AF) is anisotropic, due to the layered structure of the tissue. Three lumbar IVDs were harvested from three human spines. From each disk, four AF specimens were prepared in each of the three principal directions (axial, circumferential and radial), and four axial nucleus pulposus (NP) specimens were prepared. Conductivity was determined using a four-wire sense-current method and a custom-designed apparatus by measuring the resistance across the sample. Resistance measurements were taken at three levels of compression (0%, 10%, and 20%). Scanning electron microscopy (SEM) images of the human AF tissue were obtained in order to correlate tissue structure with conductivity results. Increasing compressive strain significantly decreased conductivity for all groups (p < 0.05, analysis of variance (ANOVA)). Additionally, specimen orientation significantly affected electrical conductivity in the AF tissue, with conductivity in the radial direction being significantly lower than that in the axial or circumferential directions at all levels of compressive strain (p < 0.05, ANOVA). Finally, conductivity in the NP tissue was significantly higher than that in the AF tissue (p < 0.05, ANOVA). SEM images of the AF tissues showed evidence of microtubes orientated in the axial and circumferential directions, but not in the radial direction. This may suggest a relationship between tissue morphology and the anisotropic behavior of conductivity in the AE The results of this investigation demonstrate that electrical conductivity in human IVD is strain-dependent and inhomogeneous, and that conductivity in the human AF tissue is anisotropic (i.e., direction-dependent). This anisotropic behavior is correlated with tissue structure shown in SEM images. This study provides important information regarding the effects of mechanical loading on solute transport and electrical behavior in IVD tissues. [DOI: 10.1115/1.3116152] Keywords: annulus fibrosus, nucleus pulposus, anisotropy, compression, tissue mechanics, electrical behavior, morphology, scanning electron microscopy