Search

We propose and demonstrate a simple all-optic control for Si photonics using a photo-thermal heater. The control light is absorbed in a heavily doped control waveguide and the signal light phase is tuned through thermal diffusion in a signal waveguide adjacent to but not optically coupled with the control waveguide. We designed and fabricated Mach–Zehnder- and microring-type devices requiring 17 (π-phase shift) and 4 (switching between resonance and non-resonance with 6 dB extinction) mW of control power, respectively. We confirmed that the heating efficiency of all-optic control exceeded that of an electrical heater placed above the signal waveguide.

We developed a thermo-optically controlled nonmechanical optical beam scanner using a Si photonic crystal slow-light waveguide with a diffraction grating to achieve on-chip light detection and ranging (LIDAR). This Letter applies pre-emphasis signals to the thermo-optic control, and the cutoff frequency increases to 500 kHz. Observing the beam scanning in the space-time domain showed that the turn-on and turn-off times of the scanner for a rectangular drive voltage were 10 µs and reduced to 2.7 µs when the pre-emphasis signals were optimized. This new, to the best of our knowledge, result enables a frame rate of 29 fps for 12,800 resolution points in LIDAR.

We have developed a nonmechanical beam scanner equipped with a Si photonics slow-light grating toward an on-chip frequency-modulated continuous-wave light detection and ranging (FMCW LIDAR) device. An optical beam is scanned thermo-optically, but it is also shifted sensitively to the frequency modulation, which is inconvenient for FMCW LIDAR. In this study, we canceled this shift and obtained step-like beam scanning with synchronized thermo-optic signals, which was confirmed in space–time-domain beam observations. The step-like scanning allows finer angular resolution of the range profile.

Optical beam scanning is a widely utilized function in optical systems and a compact nonmechanical solid-state device has long been anticipated. Here, we have studied such a device consisting of photonic crystal slow-light waveguides and switch trees, fabricated by a Si photonics process, employing a bespoke prism lens for beam collimation. Further in this study, we particularly demonstrated the operation of the device only by the thermo-optic (TO) tuning of its components, at a fixed wavelength of light. A spot beam of ∼0.1° divergence, was scanned in two dimensions, in the angular range of 40° × 8.8° and average power consumption of < 0.7 W. Neglecting some disordered beams caused by the non-uniformity of the fabricated device, the estimated number of resolution points was 400 × 32 = 12,800, which required a significant effort in the device fabrication and calibration, utilizing optical-phased arrays, if the same performance was targeted.

We have studied frequency-modulated continuous-wave (FMCW) light detection and ranging which uses externally modulated light instead of a wavelength-chirped laser diode and a complicated clock sampling circuit. In this method, the FMCW beat signal is accompanied by a 3 dB average loss in principle when pseudo frequency-modulated light simply generated by an intensity modulation with frequency-swept signals is used. In this article, we first fabricated a Si in-phase/quadrature-phase modulator equipped with compact photonic-crystal phase shifters and generated carrier-suppressed single sideband modulation signals. Furthermore, we obtained almost ideal frequency modulation, with a side-mode suppression ratio of 22.3 dB, by temporally controlling the frequency and phase of the modulation signals. When the FMCW beat signal was produced with this modulated signal in a fiber delay interferometer, its intensity was increased by 5.3 dB, as compared with that using intensity modulation. This improvement corresponds to an 80% increase in the limit distance of FMCW ranging. We also generated similar signals using a single modulator with a bypass waveguide, which simplified modulation. The side-mode suppression ratio for the frequency-swept modulation was limited to 9.8 dB, while comparably large increase in the beat intensity was confirmed.

Synthetic dimensions, which simulate spatial coordinates using non-spatial degrees of freedom, are drawing interest in topological science and other fields for modelling higher-dimensional phenomena on simple structures. We present the first realization of a synthetic frequency dimension on a silicon ring resonator photonic device fabricated using a CMOS process. We confirm that its coupled modes correspond to a 1D tight-binding model through acquisition of up to 280 GHz bandwidth optical frequency comb-like spectra, and by measuring the first synthetic band structures on an integrated device. Furthermore, we realized two types of gauge potentials along the frequency dimension, and probed their effects through the associated band structures. An electric field analogue was produced via modulation detuning, whereas effective magnetic fields were induced using synchronized nearest- and second-nearest-neighbor coupling. Creation of coupled mode lattices and two effective forces on a monolithic Si CMOS device represents a key step towards wider adoption of topological principles., 12 pages, 5 figures

In this paper, we propose and demonstrate a frequency-modulated continuous-wave light detection and ranging (LiDAR) with a Si photonic crystal beam scanner, simultaneously enabling scanning laser Doppler measurements. This nonmechanical solid-state device can reduce the size of conventional scanning laser Doppler vibrometers, making LiDAR a multimodal imaging sensor, which can measure the distributions of distance, velocity, and vibration frequency. We fabricated this device using Si photonics process and confirmed the expected operations. Distance and velocity resolutions were less than 15 mm and 19 mm/s, respectively. The detection limit of the vibration amplitude determined by the signal-to-noise ratio was 2.5 nm.

The doubly periodic Si photonic crystal waveguide operates as a nonmechanical beam-steering device that can be applied in light detection and ranging. In this Letter, we develop and describe a prism lens that collimates a fan-shaped beam, emitted from the waveguide independent of the steering angle. Its fundamental profile is investigated using a theoretical analysis for thick lenses, and then, its detailed aspherical design is obtained. In ray tracing, this prism lens suppresses the beam divergence to less than the diffraction limit in most of the targeted beam-steering range. The prism lens is fabricated by acrylic cutting, and its expected characteristics are observed.

Refractive index fronts propagating in waveguides are special spatiotemporal perturbations. The interaction of light with such fronts can be described in terms of an indirect transition where the frequency and wavenumber of a guided mode both are changed. In recent years, front-induced transitions have been used in dispersion-engineered waveguides for frequency conversion, optical delays, and bandwidth and pulse duration manipulation. These concepts have originated from different research areas of photonics, such as nonlinear fibre optics, slow-light waveguides, plasma physics, moving media and relativistic effects. Here, we discuss these concepts, providing a unifying theoretical description and highlight the potential of this exciting research field for light manipulation in guided optics., Gaafar, M.A., Baba, T., Eich, M. et al. Front-induced transitions. Nat. Photonics 13, 737–748 (2019) doi:10.1038/s41566-019-0511-6

This paper proposes and demonstrates an optical leaky wave antenna (OWLA) excited by a beam expander consisting of a slab waveguide and parabolic photonic bandgap (PBG) reflector. Conventional OLWAs are usually excited through an adiabatic taper waveguide, but its large size is a drawback. The PBG reflector is easy to fabricate with the OLWA using Si photonics technology and its size is ten times smaller than that of the adiabatic taper waveguide. We confirmed the excitation of a shallow grating waveguide, which is a kind of OLWAs, through the beam expander in simulations and measurements.

We propose an electromagnetic wave imaging system using Si photonics microring modulators (MRMs) as radio over fiber components. In this system, radio frequency signals detected at microwave probes are applied to the connected MRMs; an MRM is tuned to the laser wavelength using the thermo-optic effect to read-out through the optical transmission. By repeating this process for all MRMs and mapping the read-out signals in two dimensions, the distribution of electromagnetic waves can be visualized. Such system operation was demonstrated at 3.5 GHz in a 37.5 × 37.5 mm2 probing area, for which we confirmed the agreement with theoretical simulations.

Significance There are no biomarkers for schizophrenia (SCZ), a disorder of dysfunctional neural networks. We demonstrate that a master regulator of cytoskeleton (“CRMP2”) and, hence, neural circuitry, may form the basis for such a biomarker because its activity is uniquely imbalanced in SCZ patients. We show that SCZ patients are characterized by an excess of active CRMP2 not only in their brains (where it is correlated with dendritic abnormalities) but also in their peripheral blood lymphocytes. The abundance of active CRMP2 and insufficiency of opposing inactive p-CRMP2 likely disrupts neuronal function. Because peripheral blood CRMP2 appears to reflect intracerebral processes, it could form the basis of a rapid, minimally invasive, sensitive, and specific clinical diagnostic aid for SCZ in young patients., There are no validated biomarkers for schizophrenia (SCZ), a disorder linked to neural network dysfunction. We demonstrate that collapsin response mediator protein-2 (CRMP2), a master regulator of cytoskeleton and, hence, neural circuitry, may form the basis for a biomarker because its activity is uniquely imbalanced in SCZ patients. CRMP2’s activity depends upon its phosphorylation state. While an equilibrium between inactive (phosphorylated) and active (nonphosphorylated) CRMP2 is present in unaffected individuals, we show that SCZ patients are characterized by excess active CRMP2. We examined CRMP2 levels first in postmortem brains (correlated with neuronal morphometrics) and then, because CRMP2 is expressed in lymphocytes as well, in the peripheral blood of SCZ patients versus age-matched unaffected controls. In the brains and, more starkly, in the lymphocytes of SCZ patients

Light detection and ranging (LiDAR) is drawing attention along with the topic of autonomous vehicles, but conventional LiDAR is large and expensive due to its mechanical scanner. Therefore, compact nonmechanical solid-state LiDAR, exploiting flash illumination, optical phased array, and slow light grating have been actively developed. This presentation reviews the status of the mechanical and nonmechanical LiDAR development and introduces the challenge to realize a solid-state one using Si photonic crystal slow light waveguide.

We have developed photonic crystal slow-light devices and photonic integration. Inverse design and compatibility to Si CMOS foundry process enable practically low loss components and demonstrations of LiDAR and high-speed modulator.

We present a dynamically modulated ring resonator on a Si CMOS platform, hosting a synthetic dimension lattice over 180 GHz. The frequency and time domain synthetic band structure was acquired and photonic transport phenomena were explored.

This paper presents the comparison of optical leaky waveguide antenna, i.e., grating waveguide (GWG), waffle waveguide (WWG) and waffle-iron waveguide (WIWG) by the optical experiment.

In this chapter, the authors discuss some spontaneous emission characteristics in microcavity surface emitting lasers (SELs). Modified distribution of modes in the SEL is calculated and displayed over the optical wave vector space (k-space). The spontaneous emission factor is calculated to evaluate the amount of spontaneous emission control in the SELs and the possibility of the thresholdless operation. The spontaneous emission factor for the Bragg resonant mode in microcavity SELs is as large as 103 to 105 times that in conventional horizontal cavities. It is not so dependent on the vertical cavity quality but is almost inversely proportional to the cavity lateral size. To realize such an SEL experimentally, the reduction of the nonradiative recombination at the microcavity surface will be the important issue. In addition, investigation of the absolutely closed cavity structure will provide more remarkable effects of the microcavities.

Moving refractive index fronts in waveguides with dispersion is a special type of spatio-temporal modulation leading to the change of signal frequency and wavenumber. The interaction of light with such fronts allows frequency conversion, light stopping, optical delays as well as bandwidth and pulse duration manipulation. We will present theoretical and experimental examples of signal transmission, reflection and trapping by the front and highlight special situations such as light stopping, time reversal or optical push broom effect. We will geometrically consider indirect transitions in the dispersion relation using the phase continuity relation at the front and present numerical solutions of the linear Schrodinger equation which follows from the slowly varying envelope approximation of the wave equation. In particular, for highly dispersive waveguides a temporal evolution of the spatial wave envelopes are considered in contrast to conventional spatial evolution of temporal envelopes. Further, we will present an overview of experimental results and estimate the maximal achievable effects for each of the application in different waveguide systems.

Moving refractive index fronts in waveguides with dispersion is a special type of spatio-temporal modulation. The interaction of light with that front allows frequency conversion, light stopping, optical delays, and bandwidth and pulse duration manipulation. Here, we present examples of signal transmission, reflection, trapping and stopping. We will geometrically consider indirect transitions in the dispersion relation using the phase continuity relation at the front and present numerical solutions of the linear Schrodinger equation which follows from the slowly varying envelope approximation of the wave equation.

We modeled the photonic bands of S i O 2 -cladded Si lattice-shifted photonic crystal waveguides via machine learning and found a structure that generates low-dispersion slow light with a group index of approximately 20 in the full C-band at telecom wavelengths. The normalized delay-bandwidth product is as large as 0.45, which is close to the theoretical upper limit. The transition structure between this waveguide and a Si-channel waveguide was designed using an evolutional optimization, and a C-band average loss of 0.116 dB/transition was calculated. These results prove the possibility of further enhancing the versatility of slow light.