Search

While the mechanical performance of fused filament fabrication (FFF) parts has been extensively studied in terms of the tensile and bending strength, limited research accounts for their compressive performance. This study investigates the effect of four process parameters (layer height, extrusion width, nozzle temperature, and printing speed) on the compressive properties and surface smoothness of FFF parts made of Polylactic Acid (PLA). The orthogonal Taguchi method was employed for designing the experiments. The surface roughness and compressive properties of the specimens were then measured and optimized using the analysis of variance (ANOVA). A microscopic analysis was also performed to identify the failure mechanism under static compression. The results indicated that the layer height had the most significant influence on all studied properties, followed by the print speed in the case of compressive modulus, hysteresis loss, and residual strain; extrusion width in the case of compressive strength and specific strength; and nozzle temperature in the case of toughness and failure strain. The optimal design for both high compressive properties and surface smoothness were determined as a 0.05 mm layer height, 0.65 mm extrusion width, 205 °C nozzle temperature, and 70 mm/s print speed. The main failure mechanism observed by SEM analysis was delamination between layers, occurring at highly stressed points near the stitch line of the PLA prints. © 2023 by the authors.

This paper deals with an experimental investigation of hole quality in Al2024-T3, which is one of the aerospace alloys used in aircraft fuselage skin due to its high level of resistance to fatigue crack propagation. The experiments are conducted with 6 mm uncoated carbide and HSS drill bits using a CNC machine under dry conditions and different drilling parameters. The characteristics of the hole quality are investigated in terms of its perpendicularity, cylindricity, circularity and hole size. An ANOVA (analysis of variance) and Pareto charts are used to analyze the effects of the drilling parameters on the hole quality. The hole quality is also assessed using a digital microscope to observe the formation of hole burrs. Moreover, scanning electron microscopy is also used to investigate the inside-hole surface defects. Further investigations are carried out using optical microscopy to inspect the post-drilling tool condition at high drilling parameters. The results show that hole quality reduces as the feed rate and spindle speed increase. However, from the ANOVA results and Pareto charts, the influence of the feed rate on the hole quality is found to be insignificant. At the same time, the type of drill bit material shows the highest percentage of contribution affecting the hole quality, following the spindle speed. The HSS drill bit shows more adhesion and built-up edges than the uncoated carbide drill bit. There were more burrs formed at the hole edges when the holes were drilled with uncoated HSS drill bits. In the same way, the SEM analysis reveals more surface deformation and damage defects inside the hole walls of holes drilled using the uncoated HSS drill bit.

The advancement in 3D printing techniques has raised the hope to use additively manufactured parts as final products in various industries. However, due to the layer-by-layer nature of AM parts, they are highly susceptible to failure when they are subjected to fatigue loading. This review provides a detailed account of the influence of 3D printing parameters on the fatigue properties of parts manufactured by fused filament fabrication (FFF). Existing standards for fatigue testing of polymers and their limitation for 3D-printed parts are discussed. In addition, the cyclic behaviour of polymers is reviewed, and the impact of 3D printing parameters on the mechanical behaviour of FFF parts under tensile, compressive, flexural, and bending fatigue is investigated according to the published results in the literature. Finally, a summary of the works undertaken and suggestions for future research are provided. The influence of 3D printing parameters on the fatigue performance of prints can be different from that seen in the case of static loading and strongly depends on the fatigue loading type. While cross-over infill patterns, higher infill density, and higher layer height favour achieving higher fatigue strength in all loading types, raster orientation is best to be aligned parallel to the tensile loads and perpendicular to the compressive, flexural, and bending forces. In the case of tensile and flexural loading, Y build orientation yields the best result. Finally, print velocity was found to be less significant compared to other parameters, implying that it can be set at high values for faster printing.

Production engineering and advanced control systems make it possible to respond to the increasing needs of nations around the world. This book presents some of the new ideas, creative applications, and process optimization methods for more efficient utilization of resources available for improving productivity and reliability or lessening the times and costs of industrial production processes. It presents a variety of chapters on the development of production techniques and systems including abrasive waterjet machining, additive manufacturing, and production management. It also discusses the methods used for the development and improvement of control mechanisms with the objective of improving the reliability and efficiency of production systems. This book is useful for researchers, engineers, and experts working in different areas of production engineering and manufacturing control systems.

Abrasive waterjet machining is applied in various industries for contour cutting of heat-sensitive and difficult-to-cut materials like austenitic stainless steel 304L, with the goal of en-suring high surface integrity and efficiency. In alignment with this manufacturing aspiration, experimental analysis and optimization were carried out on abrasive waterjet machining of austenitic stainless steel 304L with the objectives of minimizing surface roughness and maximizing material removal rate. In this machining process, process parameters are critical factors influencing contour cutting performance. Accordingly, Taguchi’s S/N ratio method has been used in this study for the optimization of process parameters. Further in this work, the impacts of input parameters are in-vestigated, including waterjet pressure, abrasive mass flow rate, traverse speed and material thickness on material removal rate and surface roughness. The study reveals that an increasing level of waterjet pressure and abrasive mass flow rate achieved better surface integrity and higher material removal values. The average S/N ratio results indicate an optimum value of waterjet pressure at 300 MPa and abrasive mass flow rate of 500 g/min achieved minimum surface roughness and maximum material removal rate. It was also found that an optimized value of a traverse speed at 90 mm/min generates the lowest surface roughness and 150 mm/min produces the highest rate of material removed. Moreover, analysis of variance in the study showed that material thickness was the most influencing parameter on surface roughness and material removal rate, with a percentage contribution ranging 90.72–97.74% and 65.55–78.17%, respectively.

Abrasive water jet machining has been extensively used for cutting various materials. In particular, it has been applied for difficult-to-cut materials, mostly metals, which are used in various manufacturing processes in the fabrication industry. Due to its vast applications, in-depth comprehension of the systems behind its cutting process is required to determine its effective usage. This paper presents a review of the progress in the recent trends regarding abrasive waterjet cutting application to extend the understanding of the significance of cutting process parameters. This review aims to append a substantial understanding of the recent improvement of abrasive waterjet machine process applications, and its future research and development regarding precise cutting operations in metal fabrication sectors. To date, abrasive waterjet fundamental mechanisms, process parameter improvements and optimization reports have all been highlighted. This review can be a relevant reference for future researchers in investigating the precise machining of metallic materials or characteristic developments in the identification of the significant process parameters for achieving better results in abrasive waterjet cutting operations.

Abrasive water jet machining is a proficient alternative for cutting difficult-to-machine materials with complex geometries, such as austenitic stainless steel 304L (AISI304L). However, due to differences in machining responses for varied material conditions, the abrasive waterjet machining experiences challenges including kerf geometric inaccuracy and low material removal rate. In this study, an abrasive waterjet machining is employed to perform contour cutting of different profiles to investigate the impacts of traverse speed and material thickness in achieving lower kerf taper angle and higher material removal rate. Based on experimental investigation, a trend of decreasing the level of traverse speed and material thickness that results in minimum kerf taper angle values of 0.825° for machining curvature profile and 0.916° for line profiles has been observed. In addition, higher traverse speed and material thickness achieved higher material removal rate in cutting different curvature radii and lengths in line profiles with obtained values of 769.50 mm3/min and 751.5 mm3/min, accordingly. The analysis of variance revealed that material thickness had a significant impact on kerf taper angle and material removal rate, contributing within the range of 69–91% and 62–69%, respectively. In contrast, traverse speed was the least factor measuring within the range of 5–18% for kerf taper angle and 27–36% for material removal rate.

The integrity of machined holes depends on many parameters, some of which are related to the cutting tool (geometry, coating, material). Other influential parameters are related to the machining process variables (spindle speed, feed rate, workpiece material), all of which can affect the quality of the hole and drilling induced damage on its surface. This study investigates the effect of uncoated tools and four types of tool coatings (TiN-, TiCN-, TiAlN-, and TiSiN) on the hole quality and its microstructure. The study analyzed several hole geometrical metrics, namely hole size, circularity, cylindricity, and perpendicularity of an Al2024 aluminum alloy using a multi-spindle drilling process that utilizes three drills capable of creating multiple holes simultaneously. The results showed that the uncoated carbide drill gave a high-hole quality at low spindle speed. Regarding the coated drills, TiCN coated drills produced holes with the least deviation, circularity, cylindricity and perpendicularity at high spindle speeds. TiSiN–carbide coated drills produced the most oversized holes and noticeable damage and deformations on their surface following TiAlN and TiN. The common surface damage found on the inner hole surface was smearing, feed marks, and metal debris adhesion. The ANOVA results revealed that the tool type had the highest percentage contribution that mainly affected the hole quality.

Drilling is one of the most performed machining operations for riveting and assembly operations in many industrial sectors. The accuracy of the drilled holes and their surface finish play a vital role in the longevity and performance of the machined components, which, in turn, increase productivity. Therefore, this study investigated the effect of the multi-spindle drilling process on dimensional hole tolerances, such as hole size, circularity, cylindricity, and perpendicularity. In addition, the surface defects formed in the holes were examined using scanning electron microscopy. Three aluminium alloys, AA2024, AA6061, and AA5083, which are commonly used in the aerospace, automotive, and marine sectors, were chosen as the study materials. The results showed that the holes drilled in AA2024 gave less circularity error, cylindricity error, and perpendicularity error. In the case of hole size, the holes drilled in AA6061 were less deviated from the nominal size following holes drilled in AA2024 and AA5083 alloys. Surface damage in the form of metal debris adhesion, smeared material, side flow, and feed marks was found on the inner hole surface. Holes drilled in AA5083 alloy had the worst surface finish and were the most oversized, which was associated with noticeable damage and deformations in their inner surface. The ANOVA results revealed that the spindle speed was more influential than feed and mainly affected the hole size and cylindricity errors. However, in the case of circularity error and perpendicularity error, drilling parameters were found to be insignificant.

Drilling is an important machining process in various manufacturing industries. High-quality holes are possible with the proper selection of tools and cutting parameters. This study investigates the effect of spindle speed, feed rate, and drill diameter on the generated thrust force, the formation of chips, post-machining tool condition, and hole quality. The hole surface defects and the top and bottom edge conditions were also investigated using scan electron microscopy. The drilling tests were carried out on AA2024-T3 alloy under a dry drilling environment using 6 and 10 mm uncoated carbide tools. Analysis of Variance was employed to further evaluate the influence of the input parameters on the analysed outputs. The results show that the thrust force was highly influenced by feed rate and drill size. The high spindle speed resulted in higher surface roughness, while the increase in the feed rate produced more burrs around the edges of the holes. Additionally, the burrs formed at the exit side of holes were larger than those formed at the entry side. The high drill size resulted in greater chip thickness and an increased built-up edge on the cutting tools.

Drilling is a vital machining process for many industries. Automotive and aerospace industries are among those industries which produce millions of holes where productivity, quality, and precision of drilled holes plays a vital role in their success. Therefore, a proper selection of machine tools and equipment, cutting tools and parameters is detrimental in achieving the required dimensional accuracy and surface roughness. This subsequently helps industries achieving success and improving the service life of their products. This chapter provides an introduction to the drilling process in manufacturing industries which helps improve the quality and productivity of drilling operations on metallic materials. It explains the advantages of using multi-spindle heads to improve the productivity and quality of drilled holes. An analysis of the holes produced by a multi-spindle head on aluminum alloys Al2024, Al6061, and Al5083 is presented in comparison to traditional single shot drilling. Also the effects of using uncoated carbide and high speed steel tools for producing high-quality holes in the formation of built-up edges and burrs are investigated and discussed.

Despite the growth of composites and other lightweight materials, aluminium alloys remain an attractive choice of the aerospace industry due to their mature manufacturing processes, good resistance to fatigue crack growth and superior damage tolerance. In the aerospace industry, the drilling process is the most challenging among all the other machining process as millions of holes are required for producing riveted and bolted joints in the assembly operation of the aircraft's structures. The major challenges which arise from the drilling of these alloys are characterized by the poor hole quality which might initiate cracks within the airframe structure and reduces their reliability. This results in the rejection of parts at the assembly stage which directly impacts the manufacturing cost. Hence, appropriate selection of tool geometry, tool material and coatings, optimal cutting speed and feed rate, as well as drilling machines, is required to meet the requirement of machined parts. This motivates both academia and industries to further research on the application of drilling operations in the aircraft industry. This review aims to document details on drilling forces, drilling parameters, drill tool geometry, drill materials and coatings, chips formation, analysis of tool wear and hole metrics such as the hole size and circularity error, surface roughness, and burrs formation during the drilling of different aluminium alloys used in the aerospace industry. The focus will be mainly on Al2024 and Al7075 alloys since they are most commonly used and reported in the open literature.

Aluminium alloys are extensively used in different industries due to their good mechanical properties, machinability, low cost and reliable inspection. Drilling is one of the most important machining processes for assembly operations. The number of holes required in an assembly may vary from several holes to millions depending on the application which increases the manufacturing time and costs. In this study, a multi-spindle drill head also known as the poly-drill head is used to perform multi-hole simultaneous drilling with the aim to increase productivity. Dry drilling tests are performed on Al2024, Al6061, and Al5083 aluminium alloys using uncoated carbide tools. Thrust force, hole quality in terms of surface roughness, burr and chip formation, as well as post-machining tool conditions, were investigated under different drilling parameters. Experimental results showed that Al2024 produced fewer burrs around the hole edges, less built-up edge on tools and formed short and broken chips. Holes machined in Al6061 alloy had a good surface roughness while lowest thrust force was recorded in holes drilled in Al5083 alloy.

In industries such as aerospace and automotive, drilling many holes is commonly required to assemble different structures where machined holes need to comply with tight geometric tolerances. Multi-spindle drilling using a poly-drill head is an industrial hole-making approach that allows drilling several holes simultaneously. Optimizing process parameters also improves machining processes. This work focuses on the optimization of drilling parameters and two drilling processes-namely, one-shot drilling and multi-hole drilling-using the Taguchi method. Analysis of variance and regression analysis was implemented to indicate the significance of drilling parameters and their impact on the measured responses i.e., surface roughness and hole size. From the Taguchi optimization, optimal drilling parameters were found to occur at a low cutting speed and feed rate using a poly-drill head. Furthermore, a fuzzy logic approach was employed to predict the surface roughness and hole size. It was found that the fuzzy measured values were in good agreement with the experimental values; therefore, the developed models can be effectively used to predict the surface roughness and hole size in multi-hole drilling. Moreover, confirmation tests were performed to validate that the Taguchi optimized levels and fuzzy developed models effectively represent the surface roughness and hole size.