Search

Anisotropic surfaces with micropillar- or micropillar/nanobump structures and anisotropic wetting behavior were fabricated. Structures were arranged as three parallel zones where the structure of the middle zone differed from that of the edge zones. The widths of the middle zones were increased systematically, and the effects of the middle zone structures and widths on the contact and sliding angles of water were investigated. Structures were fabricated on PP by injection molding. Microstructured mold inserts for injection molding were obtained by structuring aluminum foils with a microworking robot, and hierarchically structured mold inserts by anodizing the microstructured foils. It was possible to create surfaces where the microstructure in the middle zone was lower or higher than on the edges, or where the middle zone had only nanostructure or was unstructured. The behavior of water on the surfaces was characterized by measuring the dynamic contact angles and sliding angles parallel and perpendicular to the zones. Hydrophobic surfaces were achieved. With appropriate middle zone widths, clearly differing parallel and perpendicular contact angles were measured and elongation of droplets along the middle zones was detected.

Micropit surfaces and hierarchically structured micropit/nanodepression surfaces were fabricated in polypropylene by injection moulding. The first step in the process was the microstructuring of aluminium foils with a micro-working robot to obtain a pattern of micropits. Dimensions of the micropits could be controlled by adjusting the working parameters of the robot. The microstructured faces of some of the foils were anodized to aluminium oxide giving a surface in which both micropits and the smooth areas between were covered with nanopores. Mould inserts for the injection moulding were obtained by cold mounting of an epoxy resin mixture on the foils. After the epoxy resin had hardened, the foils were etched away. Dimensions of the micropillars and micropillars/nanobumps on the epoxy related to the dimensions of the structures on the foils. Finally, structures were replicated in polypropylene as micropits and hierarchical micropits/nanodepressions by injection moulding. The dimensions of these hollow structures corresponded well with those of the epoxy pillars and the original micropits. Static and dynamic contact angles on the micropit-structured polypropylene surfaces were elevated from the slightly hydrophobic values of smooth polypropylene. With hierarchical micropit/nanodepression structures, the contact angles approached the superhydrophobic limit of 150°. The work demonstrates an inexpensive and reproducible technique to fabricate hollow structures of various dimensions and scales on polypropylene and modify the surface properties of the polymer.

Anisotropically microstructured and hierarchically micro/nanostructured surfaces were fabricated on polypropylene by injection moulding. Microstructured mould inserts were obtained by structuring electropolished aluminium foils with a micro-working robot, and hierarchically structured mould inserts by anodizing the microstructured aluminium foils. On both types of inserts, the microstructures were anisotropic, consisting of alternating smooth and microstructured zones. Anisotropy, and other properties of microstructures, can be controlled by adjusting the parameters of the micro-working robot. The mould inserts were used to prepare micro- and hierarchically structured polypropylene discs by injection moulding. Replication accuracy at both structure levels can be controlled through the moulding conditions. The behaviour of water on the structures was characterized by measuring the contact and sliding angles parallel and perpendicular to the microstructured zones. Surfaces with microstructures alone were highly hydrophobic, where water droplets adopted the Wenzel state and had clearly different parallel and perpendicular contact angles. Surfaces with dual structures had contact angles near 170° and sliding angles near 0°, and again the angles in parallel and perpendicular directions differed. Superhydrophobic, anisotropic Cassie–Baxter state was achieved.

Superhydrophobic polyolefin surfaces were prepared by simultaneous micro- and nanostructuring. Electropolished aluminum foil was microstructured with a micro working robot and then anodized in polyprotic acid. The surface microstructure can be tailored by adjusting the settings of the micro working robot and the nanostructure by adjusting the parameters of the anodization procedure. Surface structuring was done by injection molding where a microstructured anodized aluminum oxide mold insert was used to pattern the surfaces. Structuring had a marked effect on the contact angle between the injection-molded polyolefins and water. When the optimized microstructure was covered with nanostructure, the static contact angle between polypropylene and water obtained a value of about 165 degrees and the sliding angle decreased to about 2.5 degrees. The superhydrophobic state was achieved.

The wetting properties of polypropylene (PP) surfaces were modified by adjusting the dimensions of the surface nanostructure. The nanostructures were generated by injection molding with nanoporous anodized aluminum oxide (AAO) as the mold insert. Atomic layer deposition (ALD) of molybdenum nitride film was used to control the pore diameters of the AAO inserts. The original 50-nm pore diameter of AAO was adjusted by depositing films of thickness 5, 10, and 15 nm on AAO. Bis(tert-butylimido)-bis(dimethylamido)molybdenum and ammonia were used as precursors in deposition. The resulting pore diameters in the nitride-coated AAO inserts were 40, 30, and 20 nm, respectively. Injection molding of PP was conducted with the coated inserts, as well as with the non-coated insert. Besides the pore diameter, the injection mold temperature was varied with temperatures of 50, 70, and 90 degrees C tested. Water contact angles of PP casts were measured and compared with theoretical contact angles calculated from Wenzel and Cassie-Baxter theories. The highest contact angle, 140 degrees , was observed for PP molded with the AAO mold insert with 30-nm pore diameter. The Cassie-Baxter theory showed better fit than the Wenzel theory to the experimental values. With the optimal AAO mask, the nanofeatures in the molded PP pieces were 100 nm high. In explanation of this finding, it is suggested that some sticking and stretching of the nanofeatures occurs during the molding. Increase in the mold temperature increased the contact angle.