Search

Neomicrocalamus and Temochloa are closely-related genera for which ‘inflorescence’ structures were incompletely understood and difficult to reconcile. After re-examining the inflorescence morphology, the so-called ‘spikelets’ of both genera as described should instead be recognised as pseudospikelets with mostly inactive axillary buds. The new bamboo taxa, comprising two varieties of a new species, are placed in Temochloa, representing a new genus record for China and Vietnam.

Recently, several industries have been implementing the Cold Metal Transfer (CMT) powered Wire and Arc Additive Manufacturing (WAAM) technique because it fabricates large-scale products effectively. However, studies related to attaining uniformity in the microstructure and printing defects in the cylindrical components were lacking. So, the prime novelty is to examine the microstructural and mechanical homogeneity of the CMT-powered WAAM 304 austenitic stainless steel (SS) component. The X-ray diffraction (XRD) analysis substantiates the presence of austenite and ferrite phases all along the samples from the bottom to the top portion of the wall resulting in higher bond strength and uniformity in the microstructure. Optical Microscopy (OM) and the Scanning Electron Microscope (SEM) revealed the presence of dendritic microstructure with ferrite and austenite phases throughout the samples. The values connected to the dendritic formations are lower as a result of the reduced heat input by CMT, which leads to higher mechanical characteristics. The hardness values from the bottom to the top of the wall was 191 ± 10 HV, indicating uniformity and homogeneity in the microstructure. The tensile result showed a yield strength (σy) of 398 MPa and the ultimate tensile strength (σu) of 598 MPa and an elongation rate of 17 % in the building direction which proves the uniformity in the hardness values. Fracture morphology reveals the presence of microvoids and dimples, indicating lower ductility in the component. The Energy Dispersive Spectroscopy (EDS) also reveals the presence of higher Fe and Mn content, adding up to the successful fabrication of the cylindrical component.

Neomicrocalamus and Temochloa are closely related to bamboo genera. However, when considered with newly discovered and morphologically similar material from China and Vietnam, the phylogenetic relationship among these three groups was ambiguous in the analyses based on DNA regions. Here, as a means of investigating the relationships among the three bamboo groups and exploring potential sources of genomic conflicts, we present a phylogenomic examination based on the whole plastome, single-nucleotide polymorphism (SNP), and single-copy nuclear (SCN) gene datasets. Three different phylogenetic hypotheses were found. The inconsistency is attributed to the combination of incomplete lineage sorting and introgression. The origin of newly discovered bamboos is from introgressive hybridization between Temochloa liliana (which contributed 80.7% of the genome) and Neomicrocalamus prainii (19.3%), indicating that the newly discovered bamboos are closer to T. liliana in genetics. The more similar morphology and closer distribution elevation also imply a closer relationship between Temochloa and newly discovered bamboos.

Developing biostimulants from salt-tolerant plant growth-promoting (PGP) bacteria is an emerging strategy for sustainable agriculture in the context of increasing soil salinization. This study aimed to isolate endophytic bacteria (EB) capable of promoting rice seed germination and seedling growth at different NaCl concentrations. Nine salt-tolerant EB strains were isolated and two, ST.6 and ST.8, with the rice seed promoting effect 99.3 and 99.7 %, respectively, were selected and identified as Pantoea dispersa and Burkholderia cenocepacia, respectively. ST.6 showed a higher value of the activity of phosphatase (617 mg P ml-1), production of indole-3-acetic acid (19.7 µg IAA ml-1), the activity of 1-aminocyclopropane-1-carboxylic acid (ACC) deaminase (13.5 µmol mg−1 protein h−1), and production of siderophore (76.3 %). Especially, rice seedlings inoculated with strain ST.6 showed a significant improvement in root length (58.95 %), shoot length (16.6 %), dry biomass (7.0 %), the content of chlorophyll (46.2 and 57.1 % for chlorophyll a and b, respectively), carotenoids (22.2%), and proline (19.0 %). A decrease in antioxidant enzyme activities was also observed in the rice seedlings inoculated with either ST.6 or ST.8 strain under salt stress. Furthermore, the salt stress condition enhanced the colonization of roots by both studied endophytic bacteria. More experiments should be done to develop endophytic bacteria ST.6 and ST.8 as efficient bio-inoculants.

For additional strength increase, 5, 10, and 15% TiC was added to the quinary CoCrFeMnNi high entropy alloy (HEA) at laser powers of 100, 400, and 700 watts while selective laser melting method was engaged in the fabrication. Microstructure, porosity, density, yield and tensile strengths, elongation, and microhardness are among the parameters analyzed. As TiC appreciated from 5 to 15%, the microstructure revealed that the particles were dispersed within the matrix. Also, the addition ensued grain size refinement with increasing particle proportion. Meanwhile, 15% caused an increase in porosity, 0–10% TiC dosage and 100–700 watts laser power led to a decrease in porosity. The same dosage of TiC resulted in a linear improvement in microhardness even as 0–15% TiC ensued gradual reductions in density and elongation Increases in laser power between 100 and 700 watts were detrimental to elongation but beneficial to density and microhardness enhancement. For composites produced at 100–700 watts laser power, 5–10% TiC increased yield and ultimate tensile strengths whereas 15% TiC decreased strength. For every TiC addition, laser power 100 - 400 watts generally showed an improvement in strength and microhardness, whereas 700 watts depicted a decrease in strength and microhardness. The optimal input combination was predicted by the developed models to be 15% TiC and 504 watts laser power. Since the deviation between anticipated outcome and validation values for the responses is

Background: The coronavirus disease-2019 (COVID-19) pandemic significantly affected management of cardiovascular disease around the world. The effect of the pandemic on volume of cardiovascular diagnostic procedures is not known. Objectives: This study sought to evaluate the effects of the early phase of the COVID-19 pandemic on cardiovascular diagnostic procedures and safety practices in Asia. Methods: The International Atomic Energy Agency conducted a worldwide survey to assess changes in cardiovascular procedure volume and safety practices caused by COVID-19. Testing volumes were reported for March 2020 and April 2020 and were compared to those from March 2019. Data from 180 centers across 33 Asian countries were grouped into 4 subregions for comparison. Results: Procedure volumes decreased by 47% from March 2019 to March 2020, showing recovery from March 2020 to April 2020 in Eastern Asia, particularly in China. The majority of centers cancelled outpatient activities and increased time per study. Practice changes included implementing physical distancing and restricting visitors. Although COVID testing was not commonly performed, it was conducted in one-third of facilities in Eastern Asia. The most severe reductions in procedure volumes were observed in lower-income countries, where volumes decreased 81% from March 2019 to April 2020. Conclusions: The COVID-19 pandemic in Asia caused significant reductions in cardiovascular diagnostic procedures, particularly in low-income countries. Further studies on effects of COVID-19 on cardiovascular outcomes and changes in care delivery are warranted.

A new genus of Arundinarieae, Khoonmengia, is established to accommodate a unique new bamboo species, K. honbaensis, from central-southern Vietnam. The morphological features, habitats and distribution of Khoonmengia and related genera, i.e. Ampelocalamus and Hsuehochloa, are compared. The characters of its scrambling habit, internodes with brownish green dots, conspicuous nodes swollen at one side, elliptic buds wholly sunken into culm, extravaginal branching pattern, mid-culm branch complement with one central dominant branch elongating to reiterate the culm accompanied by several lateral slender branches, swollen culm sheath base with a distinctive zone of transverse wrinkles, synflorescence composed of only one spikelet, single or several to many synflorescences arranged into a raceme or panicle terminal on leafy branches, purple anthers and nut-like caryopsis with hardened pericarp and loosely adherent lemma and palea distinguish K. honbaensis from morphologically similar taxa. In order to investigate the phylogenetic position of this unknown bamboo, molecular phylogenetic analyses based on the nuclear gene GBSSI were also conducted, and the results proved that K. honbaensis is definitely a member of Arundinarieae with an isolated position, which also indicated that this species could not be assigned to any of the already described genera and supported the establishment of the new genus.

In recent years several notions of discrete homotopy for graphs have been introduced, including a notion of ×-homotopy due to Dochtermann. In this paper, we define a ×-homotopy fundamental groupoid for graphs, and prove that it is a functorial ×-homotopy invariant for finite graphs. We also introduce tools to compute this fundamental groupoid, including a van Kampen theorem. We conclude with a comparison with previous definitions along these lines, including those built on polyhedral complexes of graph morphisms.

The fourth industrial revolution presents an upspring opportunity for the African continent to adopt technologies such as artificial intelligence, big data, internet-enabled industrial platforms, 3D printing, robotics, nanotechnology, and blockchains. This is more so because the past three industrial revolutions saw the African continent being left out of its opportunities despite its affluent population and natural resources. Africa stands to benefit from industrial development, digitalization, and greater integration, which would result in more excellent opportunities for the growing youthful populations. However, for the digital transformation strategy and other key industry 4.0 opportunities to be successful, reliable infrastructure, affordable and stable electricity, and greater awareness are critical and imperative. This review examines the possible energy options that the continent of Africa can explore and implement for the successful deployment of Industry 4.0. The impact, difficulties, and opportunities of the fourth industrial revolution technologies on African development are discussed. Also discussed are various forms of renewable energy options based on Africa’s geographic location. This review will assist researchers and policymakers in implementing Industry 4.0 in Africa.

Elongator dysfunction is increasingly recognized as a contributor to multiple neurodevelopmental and neurodegenerative disorders including familial dysautonomia, intellectual disability, amyotrophic lateral sclerosis, and autism spectrum disorder. Although numerous cellular processes are perturbed in the context of Elongator loss, converging evidence from multiple studies has resolved Elongator's primary function in the cell to the modification of tRNA wobble uridines and the translational regulation of codon-biased genes. Here we characterize H2a.z, encoding the variant H2a histone H2A.Z, as an indirect Elongator target. We further show that canonical Notch signaling, a pathway directed by H2A.Z, is perturbed as a consequence of Elp1 loss. Finally, we demonstrate that hyperacetylation of H2A.Z and other histones via exposure to the histone deacetylase inhibitor Trichostatin A during neurogenesis corrects the expression of Notch3 and rescues the development of sensory neurons in embryos lacking the Elp1 Elongator subunit.

Augmented reality (AR) technology has recently been applied to outdoor learning in an attempt to overcome the drawbacks associated with traditional teaching environments. This study conducted an experiment designed to examine how augmented reality (AR) technology in mobile devices can be used to generate virtual objects to create a context-aware, AR-enabled guided tour application for outdoor learning. The participants were 70 elementary school students (average age: 11 years), who were randomly divided into control and experiment groups. The results showed the proposed system provided learners with a friendly, interactive interface and rich, engaging media to improve learning performance and stimulate the students’ internal motivation to learn. The system’s quantification of the learning motivations noted in Keller’s ARCS model and Kolb’s learning style theory can be used to improve the design of the learning materials. In conclusion: (1) The proposed system and activity helps stimulate learning intention via the pursuit of outdoor learning objectives, (2) the AR technology provides learners with contextual information related to the outdoor learning environment, and (3) the benefits of the proposed model do not differ for students with different learning styles.

Abstract Objective: To examine trends in leisure time physical activity and inactivity in Australians aged 15 years or older from 1989 to 2011. Method: We used data from six Australian National Health Surveys conducted from 1989/90 to 2011/12 in which physical activity was assessed using comparable questions. Analyses examined trends in the prevalence of sufficient physical activity (≥150 minutes/week moderate‐to‐vigorous physical activity) and of inactivity (

This study aimed to explore the trend in population levels, as well as the correlates, of occupational and leisure sitting time in full-time employed Australian adults between 2007 and 2015. We used data from the 2007/08, 2011/12 and 2014/15 Australian Health Surveys, in which nationally representative samples of the Australian population were interviewed. Full-time (≥35 hours/week) employed respondents reported sitting time at work and during leisure on a usual workday. Trends over time and associations between socio-demographic and health-related characteristics and sitting time were analysed in the combined dataset using multivariable logistic regression models. Over 21,000 observations were included in the analyses. Across the three surveys, approximately 51% of the respondents reported ≥4 hours/workday occupational sitting time, 40% reported ≥4 hours/workday leisure sitting time, and 55% reported ≥7 hours/workday combined occupational and leisure sitting time. There were no clear trends over time. All potential correlates were associated with occupational sitting time and all but educational level were associated with leisure sitting time. The directions of the associations with gender, age and leisure-time physical activity were reversed for occupational sitting time and leisure sitting time. These findings show that the average levels of occupational and leisure sitting time on workdays were high but stable over the past decade. The observed differences in correlates of occupational and leisure sitting time demonstrate the need to assess and address sedentary behaviour domains separately in research and policy.

Abstract Objective: To compare the level of agreement in results obtained from four physical activity (PA) measurement instruments that are in use in Australia and around the world. Methods: 1,280 randomly selected participants answered two sets of PA questions by telephone. 428 answered the Active Australia (AA) and National Health Surveys, 427 answered the AA and CDC Behavioural Risk Factor Surveillance System surveys (BRFSS), and 425 answered the AA survey and the short International Physical Activity Questionnaire (IPAQ). Results: Among the three pairs of survey items, the difference in mean total PA time was lowest when the AA and NHS items were asked (difference=24) (SE:17) minutes, compared with 144 (SE:21) mins for AA/BRFSS and 406 (SE:27) mins for AA/IPAQ). Correspondingly, prevalence estimates for ‘sufficiently active’ were similar for AA and NHS (56% and 55% respectively), but about 10% higher when BRFSS data were used, and about 26% higher when the IPAQ items were used, compared with estimates from the AA survey. Conclusions: The findings clearly demonstrate that there are large differences in reported PA times and hence in prevalence estimates of ‘sufficient activity’ from these four measures. Implications: It is important to consistently use the same survey for population monitoring purposes. As the AA survey has now been used three times in national surveys, its continued use for population surveys is recommended so that trend data over a longer period of time can be established.

Traditionally, the teaching of history course mostly utilizes face to face instruction and oral presentation. Along with the development of educational technology, the teaching methods could be more various such as using internet and multimedia. Literature reviews also indicate that using internet and multimedia may improve the effect of learning and teaching. This paper explores the development of a web-based instructional system for the course of Taiwanese History at Shih Hsin University. The result and the product of this development project is the web site, http://distance.shu.edu.tw/taiwan/list.htm. The content of the web-site includes instructional materials such as animations, videoes, pictures, textes, historical maps, and so on. The developmental methods used in this project use curriculum design, survey, interview, review of literatures and focus group discussion. (Article content in Chinese with English abstract)

Background: Little is known about the effect of recurrent episodes of communal violence on mental health in countries recovering from mass conflict. We report results of a 6-year longitudinal study in post-conflict Timor-Leste assessing changes in mental health after a period of communal violence. Methods: We assessed 1022 adults (600 from a rural village, 422 from an urban district) exposed to mass conflict during the Indonesian occupation after independence in 2004, and again in 2010–11, following a period of internal conflict. We took a census of all adults living at the two sites. The survey included measures of post-traumatic stress disorder, severe distress, traumatic events, poverty, ongoing conflict, and injustice. Findings: 1247 (80%) of 1554 invited adults participated in the baseline survey. 1038 (89% of those eligible) were followed up. The analysis included 1022 people who had sufficient data at baseline and follow-up. The prevalence of post-traumatic stress disorder increased from 23 of 1022 (2·3%) in 2004, to 171 of 1022 (16·7%) in 2010. The prevalence of severe distress also increased, from 57 of 1022 (5·6%) in 2004, to 162 of 1022 (15·9%) in 2010. Both these outcomes were associated with disability at follow-up. Having post-traumatic stress at follow-up was associated with being a woman (odds ratio [OR] 1·63, 95% CI 1·14–2·32), experience of human rights trauma (OR 1·25, 95% CI 1·07–1·47), or exposure to murder (OR 1·71, 95% CI 1·38–2·10) during the Indonesian occupation (1975–99), human rights trauma during the period of internal violence in 2006–07 (OR 1·46, 95% CI 1·04–2·03), and ongoing family or community conflict (OR 1·80, 95% CI 1·15–2·80) or preoccupations with injustice for two or three historical periods (OR 4·06, 2·63–6·28). Severe distress at follow-up was associated with health stress (OR 1·47, 1·14–1·90), exposure to murder (OR 1·57, 1·27–1·95), and natural disaster (OR 1·65, 1·03–2·64) during the Indonesian occupation, conflict-related trauma during the internal violence (OR 1·33, 1·02–1·74), and ongoing poverty (OR 1·53, 1·36–1·72) or preoccupations with injustice for two or three historical periods (OR 2·09, 1·25–3·50). Interpretation: Recurrent violence resulted in a major increase in post-traumatic stress disorder and severe distress in a community previously exposed to mass conflict. Poverty, ongoing community tensions, and persisting feelings of injustice contributed to mental disorders. The findings underscore the importance of preventing recurrent violence, alleviating poverty, and addressing injustices in countries emerging from conflict. Funding: Australian National Health and Medical Research Council.

INTRODUCTION: Findings regarding the association between overweight and all-cause mortality range from significantly lower to higher risk, compared with body-mass-index (BMI) within the "normal" range. METHODS: We examined empirically potential methodological explanations for these apparently conflicting results using questionnaire and linked mortality data from 246,314 individuals aged ≥45 years in the Australian 45 and Up Study (11,127 deaths; median follow-up 3.9 years). Hazard ratios (HR) for all-cause mortality associated with BMI were modelled according to different methods of accounting for illness at baseline, finer versus broader gradations of BMI and choice of reference group, adjusting for potential confounders. RESULTS: In analyses using the broad World Health Organization (WHO) categories, the all-cause mortality HR was significantly lower in the overweight category (25.0-29.99 kg/m²), than the normal weight (18.5-24.99 kg/m²) category. However, in analyses accounting for baseline illness, which excluded those with pre-existing illness at baseline, ever-smokers and the first 2 years of follow up, absolute age-standardised mortality rates varied up to two-fold between finer BMI categories within the WHO normal weight category; rates were lowest at 22.5-24.99 kg/m² and mortality HRs increased steadily for BMI above (p(trend)

Each year, about six million tons of lactose are generated from liquid whey as industrial byproduct, and optimally this large carbohydrate waste should be used for the production of value-added products. Trametes multicolor pyranose 2-oxidase (TmP2O) catalyzes the oxidation of various monosaccharides to the corresponding 2-keto sugars. Thus, a potential use of TmP2O is to convert the products from lactose hydrolysis, D-glucose and D-galactose, to more valuable products such as tagatose. Oxidation of glucose is however strongly favored over galactose, and oxidation of both substrates at more equal rates is desirable. Characterization of TmP2O variants (H450G, V546C, H450G/V546C) with improved D-galactose conversion has been given earlier, of which H450G displayed the best relative conversion between the substrates. To rationalize the changes in conversion rates, we have analyzed high-resolution crystal structures of the aforementioned mutants with bound 2- and 3-fluorinated glucose and galactose. Binding of glucose and galactose in the productive 2-oxidation binding mode is nearly identical in all mutants, suggesting that this binding mode is essentially unaffected by the mutations. For the competing glucose binding mode, enzyme variants carrying the H450G replacement stabilize glucose as the α-anomer in position for 3-oxidation. The backbone relaxation at position 450 allows the substrate-binding loop to fold tightly around the ligand. V546C however stabilize glucose as the β-anomer using an open loop conformation. Improved binding of galactose is enabled by subtle relaxation effects at key active-site backbone positions. The competing binding mode for galactose 2-oxidation by V546C stabilizes the β-anomer for oxidation at C1, whereas H450G variants stabilize the 3-oxidation binding mode of the galactose α-anomer. The present study provides a detailed description of binding modes that rationalize changes in the relative conversion rates of D-glucose and D-galactose and can be used to refine future enzyme designs for more efficient use of lactose-hydrolysis byproducts.

Varying concentrations of lipopolysaccharide (LPS) in ovalbumin (OVA) may influence the airway response to allergic sensitization and challenge. We assessed the contribution of LPS to allergic airway inflammatory responses following challenge with LPS-rich and LPS-free commercial OVA. BALB/c mice were sensitized with LPS-rich OVA and alum and then underwent challenge with the same OVA (10 µg intranasally) or an LPS-free OVA. Following challenge, bronchoalveolar lavage (BAL), airway responsiveness to methacholine and the lung regulatory T cell population (Treg) were assessed. Both OVA preparations induced BAL eosinophilia but LPS-rich OVA also evoked BAL neutrophilia. LPS-free OVA increased interleukin (IL)-2, IL-4 and IL-5 whereas LPS-rich OVA additionally increased IL-1β, IL-12, IFN-γ, TNF-α and KC. Both OVA-challenged groups developed airway hyperresponsiveness. TLR4-deficient mice challenged with either OVA preparation showed eosinophilia but not neutrophilia and had increased IL-5. Only LPS-rich OVA challenged mice had increased lung Tregs and LPS-rich OVA also induced in vitro Treg differentiation. LPS-rich OVA also induced a Th1 cytokine response in human peripheral blood mononuclear cells.We conclude that LPS-rich OVA evokes mixed Th1, Th2 and innate immune responses through the TLR-4 pathway, whereas LPS-free OVA evokes only a Th2 response. Contaminating LPS is not required for induction of airway hyperresponsiveness but amplifies the Th2 inflammatory response and is a critical mediator of the neutrophil, Th1 and T regulatory cell responses to OVA.

Pyranose dehydrogenases (PDHs) are extracellular flavin-dependent oxidoreductases secreted by litter-decomposing fungi with a role in natural recycling of plant matter. All major monosaccharides in lignocellulose are oxidized by PDH at comparable yields and efficiencies. Oxidation takes place as single-oxidation or sequential double-oxidation reactions of the carbohydrates, resulting in sugar derivatives oxidized primarily at C2, C3 or C2/3 with the concomitant reduction of the flavin. A suitable electron acceptor then reoxidizes the reduced flavin. Whereas oxygen is a poor electron acceptor for PDH, several alternative acceptors, e.g., quinone compounds, naturally present during lignocellulose degradation, can be used. We have determined the 1.6-Å crystal structure of PDH from Agaricus meleagris. Interestingly, the flavin ring in PDH is modified by a covalent mono- or di-atomic species at the C(4a) position. Under normal conditions, PDH is not oxidized by oxygen; however, the related enzyme pyranose 2-oxidase (P2O) activates oxygen by a mechanism that proceeds via a covalent flavin C(4a)-hydroperoxide intermediate. Although the flavin C(4a) adduct is common in monooxygenases, it is unusual for flavoprotein oxidases, and it has been proposed that formation of the intermediate would be unfavorable in these oxidases. Thus, the flavin adduct in PDH not only shows that the adduct can be favorably accommodated in the active site, but also provides important details regarding the structural, spatial and physicochemical requirements for formation of this flavin intermediate in related oxidases. Extensive in silico modeling of carbohydrates in the PDH active site allowed us to rationalize the previously reported patterns of substrate specificity and regioselectivity. To evaluate the regioselectivity of D-glucose oxidation, reduction experiments were performed using fluorinated glucose. PDH was rapidly reduced by 3-fluorinated glucose, which has the C2 position accessible for oxidation, whereas 2-fluorinated glucose performed poorly (C3 accessible), indicating that the glucose C2 position is the primary site of attack.

To quantify the association between daily total sitting and all-cause mortality risk and to examine dose-response relationships with and without adjustment for moderate-to-vigorous physical activity.Studies published from 1989 to January 2013 were identified via searches of multiple databases, reference lists of systematic reviews on sitting and health, and from authors' personal literature databases. We included prospective cohort studies that had total daily sitting time as a quantitative exposure variable, all-cause mortality as the outcome and reported estimates of relative risk, or odds ratios or hazard ratios with 95% confidence intervals. Two authors independently extracted the data and summary estimates of associations were computed using random effects models.Six studies were included, involving data from 595,086 adults and 29,162 deaths over 3,565,569 person-years of follow-up. Study participants were mainly female, middle-aged or older adults from high-income countries; mean study quality score was 12/15 points. Associations between daily total sitting time and all-cause mortality were not linear. With physical activity adjustment, the spline model of best fit had dose-response HRs of 1.00 (95% CI: 0.98-1.03), 1.02 (95% CI: 0.99-1.05) and 1.05 (95% CI: 1.02-1.08) for every 1-hour increase in sitting time in intervals between 0-3, >3-7 and >7 h/day total sitting, respectively. This model estimated a 34% higher mortality risk for adults sitting 10 h/day, after taking physical activity into account. The overall weighted population attributable fraction for all-cause mortality for total daily sitting time was 5.9%, after adjusting for physical activity.Higher amounts of daily total sitting time are associated with greater risk of all-cause mortality and moderate-to-vigorous physical activity appears to attenuate the hazardous association. These findings provide a starting point for identifying a threshold on which to base clinical and public health recommendations for overall sitting time, in addition to physical activity guidelines.

BackgroundMental disorders are likely to be elevated in the Libyan population during the post-conflict period. We estimated cases of severe PTSD and depression and related health service requirements using modelling from existing epidemiological data and current recommended mental health service targets in low and middle income countries (LMIC's).MethodsPost-conflict prevalence estimates were derived from models based on a previously conducted systematic review and meta-regression analysis of mental health among populations living in conflict. Political terror ratings and intensity of exposure to traumatic events were used in predictive models. Prevalence of severe cases was applied to chosen populations along with uncertainty ranges. Six populations deemed to be affected by the conflict were chosen for modelling: Misrata (population of 444,812), Benghazi (pop. 674,094), Zintan (pop. 40,000), displaced people within Tripoli/Zlitan (pop. 49,000), displaced people within Misrata (pop. 25,000) and Ras Jdir camps (pop. 3,700). Proposed targets for service coverage, resource utilisation and full-time equivalent staffing for management of severe cases of major depression and post-traumatic stress disorder (PTSD) are based on a published model for LMIC's.FindingsSevere PTSD prevalence in populations exposed to a high level of political terror and traumatic events was estimated at 12.4% (95%CI 8.5-16.7) and was 19.8% (95%CI 14.0-26.3) for severe depression. Across all six populations (total population 1,236,600), the conflict could be associated with 123,200 (71,600-182,400) cases of severe PTSD and 228,100 (134,000-344,200) cases of severe depression; 50% of PTSD cases were estimated to co-occur with severe depression. Based upon service coverage targets, approximately 154 full-time equivalent staff would be required to respond to these cases sufficiently which is substantially below the current level of resource estimates for these regions.DiscussionThis is the first attempt to predict the mental health burden and consequent service response needs of such a conflict, and is crucially timed for Libya.

Abstract Replication of the Japanese encephalitis virus (JEV) genome depends on host factors for successfully completing their life cycles; to do this, host factors have been recruited and/or relocated to the site of viral replication. Glyceraldehyde-3-phosphate dehydrogenase (GAPDH), a cellular metabolic protein, was found to colocalize with viral RNA-dependent RNA polymerase (NS5) in JEV-infected cells. Subcellular fractionation further indicated that GAPDH remained relatively constant in the cytosol, while increasing at 12 to 24 hours postinfection (hpi) and decreasing at 36 hpi in the nuclear fraction of infected cells. In contrast, the redistribution patterns of GAPDH were not observed in the uninfected cells. Co-immunoprecipitation of GAPDH and JEV NS5 protein revealed no direct protein-protein interaction; instead, GAPDH binds to the 3' termini of plus- and minus-strand RNAs of JEV by electrophoretic mobility shift assays. Accordingly, GAPDH binds to the minus strand more efficiently than to the plus strand of JEV RNAs. This study highlights the findings that infection of JEV changes subcellular localization of GAPDH suggesting that this metabolic enzyme may play a role in JEV replication.

Study Design: Meta-analysis., Objective: To compare the effectiveness of postoperative pain control between erector spinae plane block (ESPB) and thoracolumbar interfascial plane (TLIP) block in lumbar spine surgery., Methods: PubMed, Embase, and MEDLINE electronic databases were searched for articles containing randomized controlled trials (RCTs) published between January 1900 and January 2024. We extracted the postoperative mean pain score, the first 24-h postoperative morphine consumption, and their standard deviation from the included studies. Meta-analysis was performed using the functions available in the metafor package in R software. We pooled continuous variables using an inverse variance method with a random-effects model and summarized them as standardized mean differences., Results: Five RCTs that directly compared the ESPB and TLIP block in lumbar spine surgery were included, enrolling 432 participants randomly into the two groups with 216 participants in each group. The pooled analyses showed that there was no significant difference between the ESPB and TLIP groups in terms of lower pain scores during the early (1 h) (standardized mean difference [SMD] -1.49, 95% confidence interval [CI], -3.10; 0.11), middle (12 h) (SMD -3.12, 95% CI, -6.86; 0.61), and late (24 h) (SMD -1.38, 95% CI, -3.01; 0.24) postoperative periods. There was also no significant difference in the first 24-h postoperative morphine equivalent consumption between the ESPB and TLIP groups (SMD -0.46 mg, 95% CI -1.23; 0.31)., Conclusion: No significant difference was observed between the ESPB and TLIP block in terms of postoperative pain control and 24-h morphine equivalent consumption for lumbar spine surgery., Competing Interests: Declaration of Conflicting InterestsThe author(s) declared no potential conflicts of interest with respect to the research, authorship, and/or publication of this article.

All-inorganic perovskites show great promise as an emission layer in perovskite light-emitting diodes (PeLEDs) owing to their easy solution processing, low manufacturing cost, and excellent optoelectronic properties. However, there is still an immense performance gap from small-area devices to large-area PeLED devices. The inhomogeneity of large-area high-quality perovskite films inevitably leads to vast defects and electroluminescence performance losses. Herein, a post-hot-cast annealing deposition scheme and the introduction of the multifunctional molecule 2-amino-1,3-propanediol (APDO) were proposed to regulate the crystallization of the perovskite film. As a result, uniform APDO:CsPbBr 2.5 Cl 0.5 perovskite films with high crystallinity and lower defect density were deposited by post-hot-cast annealing. A decent maximum brightness of 2659 cd m -2 was achieved for the large-area cyan PeLEDs with an emitting area of 400 mm 2 ., Competing Interests: The authors declare no competing interests., (This journal is © The Royal Society of Chemistry.)

This study uses different doping ratios of CsCl and MACl dual additives to improve the quality of the perovskite, where CsCl reduces the perovskite trap density and increases the resistance of charge recombination, and MACl was used to improve the phase stability. Finally, the composition of Cs 0.1 MA 0.09 FA 0.81 PbCl 0.14 I 2.86 perovskite solar cell (PeSC) can achieve better open-circuit voltage (Voc), short-circuit current density (Jsc), and photoelectric conversion efficiency (PCE). To achieve a better PCE of PeSC, the use of organic ammonium salt butane-1,4-diammonium iodide (BDAI 2 ) to passivate the perovskite bottom surface (buried interface) can effectively suppress the formation of defects at the perovskite buried interface, obtain higher crystallinity, and thereby reduce the probability of carrier recombination. The Jsc, fill factor (FF), and PCE of the PeSC based on BDAI 2 passivation increased from 24.0 mA cm -2 , 74.1%, and 18.6% to 24.5 mA cm -2 , 79.9%, and 20.5%, respectively., Competing Interests: The authors declare no competing financial interest., (© 2024 The Authors. Published by American Chemical Society.)

Lensless computational imaging, a technique that combines optical-modulated measurements with task-specific algorithms, has recently benefited from the application of artificial neural networks. Conventionally, lensless imaging techniques rely on prior knowledge to deal with the ill-posed nature of unstructured measurements, which requires costly supervised approaches. To address this issue, we present a self-supervised learning method that learns semantic representations for the modulated scenes from implicitly provided priors. A contrastive loss function is designed for training the target extractor (measurements) from a source extractor (structured natural scenes) to transfer cross-modal priors in the latent space. The effectiveness of the new extractor was validated by classifying the mask-modulated scenes on unseen datasets and showed the comparable accuracy to the source modality (contrastive language-image pre-trained [CLIP] network). The proposed multimodal representation learning method has the advantages of avoiding costly data annotation, being more adaptive to unseen data, and usability in a variety of downstream vision tasks with unconventional imaging settings.

Addressing the critical challenge of mitigating defect generation and enhancing the extended durability of perovskite solar cells (PeSCs) requires effective passivation materials. In our study, we investigated the impact of varying concentrations of cesium iodide (CsI), an alkali halide, on the interface layer among the hole transporting layer (HTL) and the perovskite film in a triple-cation lead hybrid halide Cs 0.15 FA 0.81 MA 0.04 Pb(I 2.86 Br 0.14 ) 3 perovskite layer. Our findings revealed that the introduction of CsI into the NiOx HTL led to improved crystallinity and a reduction in defects within the perovskite film. Consequently, the photovoltaic performance of the CsI-modified PeSC exhibited a notable enhancement. Specifically, the photoelectric conversion efficiency (PCE) increased from 18.7 % in the original PeSC, which lacked CsI modification, to 20.5 %. Moreover, this improvement in PCE was accompanied by excellent stability, with the CsI-modified PeSC retaining 80 % of its opening PCE even afterward 144 h of testing., Competing Interests: The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (© 2024 The Authors.)

Background: Oligoprogression is an emerging issue in patients with epidermal growth factor receptor (EGFR)-mutated non-small cell lung cancer (NSCLC). However, the surgical treatment for central nervous system (CNS) oligoprogression is not widely discussed. We investigated the outcomes of craniotomy with adjuvant whole-brain radiotherapy (WBRT) and subsequent therapies for CNS oligoprogression in patients with EGFR-mutated NSCLC., Methods: NSCLC patients with CNS oligoprogression were identified from a tertiary medical center. The outcomes of surgery with adjuvant WBRT or WBRT alone were analyzed, along with other variables. Overall survival and progression-free survival were analyzed using the log-rank test as the primary and secondary endpoints. A COX regression model was used to identify the possible prognostic factors., Results: Thirty-seven patients with CNS oligoprogression who underwent surgery or WBRT were included in the study after reviewing 728 patients. Twenty-one patients underwent surgery with adjuvant WBRT, and 16 received WBRT alone. The median overall survival for surgery and WBRT alone groups was 43 (95% CI 17-69) and 22 (95% CI 15-29) months, respectively. Female sex was a positive prognostic factor for overall survival (OR 0.19, 95% CI 0.06-0.57). Patients who continued previous tyrosine kinase inhibitors (OR 3.48, 95% CI 1.06-11.4) and induced oligoprogression (OR 3.35, 95% CI 1.18-9.52) were associated with worse overall survival. Smoking history (OR 4.27, 95% CI 1.54-11.8) and induced oligoprogression (OR 5.53, 95% CI 2.1-14.7) were associated with worse progression-free survival., Conclusions: Surgery combined with adjuvant WBRT is a feasible treatment modality for CNS oligoprogression in patients with EGFR-mutated NSCLC. Changing the systemic-targeted therapy after local treatments may be associated with improved overall survival., (© 2023. The Author(s).)

The clip-induced spinal cord injury (SCI) rat model is pivotal in preclinical SCI research. However, the literature exhibits variability in compression duration and limited attention to clip deformation-related loss of closure force. We aimed to investigate the impact of compression duration on SCI severity and the influence of clip deformation on closure force. Rats received T10-level clip-induced SCI with durations of 1, 5, 10, 20, and 30 s, and a separate group underwent T10 transection. Outcomes included functional, histological, electrophysiological assessments, and inflammatory cytokine analysis. A tactile pressure mapping system quantified clip closure force after open-close cycles. Our results showed a positive correlation between compression duration and the severity of functional, histological, and electrophysiological deficits. Remarkably, even a brief 1-s compression caused significant deficits comparable to moderate-to-severe SCI. SSEP waveforms were abolished with durations over 20 s. Decreased clip closure force appeared after five open-close cycles. This study offers critical insights into regulating SCI severity in rat models, aiding researchers. Understanding compression duration and clip fatigue is essential for experiment design and interpretation using the clip-induced SCI model.

Introduction: Hypothyroidism is a rare and possible cause of hyponatremia. However, the clinical epidemiology and risk of mortality (ROM) when they coexist still remain elusive., Objectives: We assessed the epidemiology and ROM among index patients with coexisting hypothyroidism and hyponatremia via a national population database., Patients and Methods: This retrospective cohort study utilized Taiwan's National Health Insurance program database. Distributions of definite sociodemographic factors were analyzed. The annual incidence among the overall group and sex-subgroups was investigated. In addition, potential factors influencing the ROM were also evaluated., Results: Of 4,549,226 patients from 1998 to 2015, a total of 3,140 index patients with concurrent hypothyroidism and hyponatremia were analyzed. The incidence rate increased tenfold from 1998 to 2015; average annual incidence rate was 174. Among the total participants, 57.1% were women; mean age was 72.6 ± 14.7 years and 88.8% were aged > 55 years. Although average length of stay (LOS) was 13.1 ± 15.4 days, the mortality group had significantly longer LOS than that in the survival group (12.9 days vs 22.2 days). Old age, catastrophic illness, cardiac dysrhythmia, and low hospital hierarchy were independent predictors of hospital mortality. The optimal LOS cutoff value for ROM prediction was 16 days. Index patients with LOS > 16 days increased ROM by 2.3-fold., Conclusions: Coexistent hypothyroidism and hyponatremia is rare, although the incidence increased gradually. Factors influencing the ROM, such as old age, underlying catastrophic status, cardiac dysrhythmia, hospital hierarchy, and LOS should be considered in clinical care., (© 2023. BioMed Central Ltd., part of Springer Nature.)

Perovskite solar cells (PeSCs) have been introduced as a new photovoltaic device due to their excellent power conversion efficiency (PCE) and low cost. However, due to the limitations of the perovskite film itself, the existence of defects was inevitable, which seriously affects the number and mobility of carriers in perovskite solar cells, thus restricting PeSCs improved efficiency and stability. Interface passivation to improve the stability of perovskite solar cells is an important and effective strategy. Here, we use methylammonium halide salts (MAX, X = Cl, Br, I) to effectively passivate defects at or near the interface of perovskite quantum dots (PeQDs)/triple-cation perovskite films. The MAI passivation layer increased the open circuit voltage of PeQDs/triple-cation PeSC by 63 mV up to 1.04 V, with a high short-circuit current density of 24.6 mA cm -2 and a PCE of 20.4%, which demonstrated a significant suppression of interfacial recombination., (© 2023. The Author(s).)

Background: Peripheral intravenous catheterization (PIVC) is pivotal to pediatric medical care; however, it is a challenging technique for pediatricians, and the parameters affecting successful pediatric PIVC establishment have not been fully investigated., Methods: This prospective observational study collected data from pediatric patients aged less than 18 years who required PIVC. The participants were categorized into five groups for subgroup analysis: newborn, infant, toddler, pre-school, and student (children and adolescent). Data on demography, biochemistry, and PIVC executors were examined to elucidate the most powerful factors affecting the success of PIVC., Results: A total of 935 peripheral venous cannulations conducted within 1 year were studied. Age-subgroup analysis showed the highest failure rate (FR) of PIVC in the infant group (18.4%). No significant difference in BMI standard deviation score was noted among the groups (p-value = 0.430). Compared with those for the success group, more attempts, longer completion time, and more medical staff were needed for the failure group (all p-values < 0.05). A high serum procalcitonin level was correlated with an increased FR (p-value = 0.016). In addition, the success rate was positively associated with the seniority of the operators, except for the 3-year experienced R3 group (93.5%) showing a higher success rate than the 4-year experienced CR group (84.2%)., Conclusions: Difficulty in setting up PIVC was the greatest in infants and even greater than that in newborns. Even though seniority was a cardinal factor in successful PIVC, a high FR was still noted despite the lack of continuous and steady practice., Competing Interests: Declaration of competing interest The authors declare that they have no competing interests., (Copyright © 2022 Taiwan Pediatric Association. Published by Elsevier B.V. All rights reserved.)

Two-dimensional (2D) perovskite have been widely researched for solar cells, light-emitting diodes, photodetectors because of their excellent environmental stability and optoelectronic properties in comparison to three-dimensional (3D) perovskite. In this study, we demonstrate the high response of 2D-(PEA) 2 PbBr 4 perovskite of the horizontal vapor sensor was outstandingly more superior than 3D-MAPbBr 3 perovskite. 2D transverse perovskite layer have the large surface-to-volume ratio and reactive surface, with the charge transfer mechanism, which was suitable for vapor sensing and trapping. Thus, 2D perovskite vapor sensors demonstrate the champion current response ratio R of 107.32 under the ethanol vapors, which was much faster than 3D perovskite (R = 2.92).

Perovskite solar cells (PeSCs) were fabricated by using Cs x FA 1- x PbI 3- x Cl x as the photoactive layer, and the effects of different proportions of cesium chloride (CsCl)/formamidinium iodide on perovskites were investigated. Cesium (Cs) can stabilize the α phase of the perovskite, while chlorine (Cl) can increase the size and crystallinity of perovskite crystals and reduce non-radiative cladding, thereby improving the performance of the overall device. The maximum power conversion efficiency (PCE) measured for Cs 0.2 FA 0.8 PbI 2.8 Cl 0.2 -based PeSCs was 18.9%. To further improve the photovoltaic characteristics of PeSCs, Cs 0.2 FA 0.8 PbI 2.8 Cl 0.2 -based PeSCs were introduced into different concentrations of phenethylammonium iodide (PEAI) to modify the interface between the NiO x hole transport layer (HTL) and the perovskite photoactive layer, which can simultaneously promote excellent crystallinity of the perovskite layer and passivated interfacial defects, reducing recombination near the perovskite/HTL interface in PeSCs, thereby increasing the efficiency of the device. Compared with the control Cs 0.2 FA 0.8 PbI 2.8 Cl 0.2 -based PeSC, the PCE of PeSC with the PEAI (10 mg/mL)-modified NiO x /perovskite interface increased significantly from 18.9 to 20.2%., Competing Interests: The authors declare no competing financial interest., (© 2022 The Authors. Published by American Chemical Society.)

The discovery of new reactions enables chemists to attain a better understanding of fundamental chemical reactivity and push the boundaries of organic synthesis. Our understanding and manipulation of high-energy states such as reactive conformations, intermediates, and transition structures contribute to this field. Herein we interrogate epoxide ring-closure by inserting the C[double bond, length as m-dash]N functionality into a well-known precursor to nucleophilic epoxide ring-closure. The synthesis of tetrasubstituted, nitrile-tethered epoxides takes place via activation of iminologous diols followed by fragmentation. Mechanistic study reveals the transformation to be stereospecific, which is consistent with the concerted nature of the epoxide ring-closure., Competing Interests: A. K. Y. is an associate editor of Chemical Science., (This journal is © The Royal Society of Chemistry.)

Face recognition plays an essential role for the biometric authentication. Conventional lens-based imagery keeps the spatial fidelity with respect to the object, thus, leading to the privacy concerns. Based on the point spread function engineering, we employed a coded mask as the encryption scheme, which allows a readily noninterpretable representation on the sensor. A deep neural network computation was used to extract the features and further conduct the identification. The advantage of this data-driven approach lies in that it is neither necessary to correct the lens aberration nor revealing any facial conformity amid the image formation chain. To validate the proposed framework, we generated a dataset with practical photographing and data augmentation by a set of experimental parameters. The system has the capability to adapt a wide depth of field (DoF) (60-cm hyperfocal distance) and pose variation (0 to 45 deg). The 100% recognition accuracy on real-time measurement was achieved without the necessity of any physics priors, such as the encryption scheme.

This report outlines a proposed method of packaging wide-angle (WA) mini-light-emitting diode (mini-LED) devices without optical lenses to create a highly efficient, ultrathin, flexible planar backlight for portable quantum dot light-emitting diode (QLED) displays. Since the luminous intensity curve for mini-LEDs generally recommends a beam angle of 120°, numerous LEDs are necessary to achieve a uniform surface light source for a QLED backlight. The light-guide layer and diffusion layer were packaged together on a chip surface to create WA mini-LEDs with a viewing angle of 180°. These chips were then combined with a quantum dot (QD) film and an optical film to create a high-efficiency, ultrathin, flexible planar light source with excellent color purity that can be used as a QLED display backlight. A 6 in (14.4 cm) light source was used as an experimental sample. When 1.44 W was supplied to the sample, the 3200-piece WA mini-LED with a flexible planar QLED display had a beam angle of 180° on the luminous intensity curve, a planar backlight thickness of 0.98 mm, a luminance of 10,322 nits, and a luminance uniformity of 92%.

We propose the use of optical films to enhance the light extraction efficiency (LEE) and wide-angle emission of traditional packaged deep-ultraviolet light-emitting diodes (DUV-LEDs). Total internal reflection occurs easily in DUV-LEDs because they contain sapphire, which has a high refractive index. DUV-LEDs also contain an aluminum nitride (AlN) ceramic substrate, which has high light absorption in the ultraviolet band. Photons are absorbed by the sapphire and AlN ceramic substrate, which reduces the LEE of DUV-LEDs. By adding a brightness enhancement film (BEF) on the sapphire surface and a high-reflection film (HRF) on the surface of the AlN ceramic substrate, the LEE of DUV-LEDs can be increased. Moreover, we designed a single-layer metal reflective film (SMRF) on the upper surface of the quartz glass in order to achieve wide-angle emission. Experimental results indicated that compared with traditional packaged DUV-LEDs, the light output power and external quantum efficiency of DUV-LEDs with a plated BEF, HRF, and SMRF increased by 18.3% and 18.2%, respectively. Moreover, an emission angle of 160° was achieved. In a reliability test, DUV-LEDs maintained more than 95% of the initial forward voltage and light output power after 1000 h of operation at 25°C, which indicated that the addition of an optical film can improve the light efficiency and long-term reliability of DUV-LEDs.

This prospective randomized trial examined the effects of a tripartite intervention (behavioral state modulation + nonnutritive sucking + tucking) on stress from procedural pain during heel pricks. Blood samples for routine screening were collected by heel pricks 48 h after birth (Stage 1) and at ≥37 weeks' gestation (Stage 2); salivary cortisol levels (SCLs) pre-prick (T0) and 20 min post-prick (T1) assessed stress. Preterm infants (n = 64) sampled by convenience at Level III neonatal care units were randomly assigned to the control condition (usual care) or intervention condition (tripartite intervention). Generalized estimating equations examined differences in salivary cortisol between conditions. After adjusting for effects of gestational age, postmenstrual age, and baseline SCLs, (1) at Stage 1, the change in salivary cortisol from T0 to T1 in preterm infants who received the tripartite intervention was, on average, significantly lower by 0.431 units (log scale) than the change in preterm infants who received the control condition (p < 0.001); (2) in the tripartite intervention condition, the difference between the change in mean SCLs from T0 to T1 at Stages 1 and 2 was significantly lower by 0.287 units (log scale), on average than between the change at Stages 1 and 2 in the control condition (p = 0.026). The provision of a tripartite intervention during heel prick significantly decreased the raise of SCLs compared with infants receiving usual care, suggesting lower stress. Clinicians could easily implement the tripartite intervention for heel-stick support; however, replication is needed before recommending its incorporation into routine heel stick and other stressful procedures., (© 2021 Wiley Periodicals LLC.)

Background: To investigate whether serial morphometric measurements of the brainstem using high resolution trans-foramen-magnum ultrasound (US) in premature neonates correlate with neurological outcomes. Methods: Serial brain ultrasound scans were performed in 36 consecutive preterm infants born at <34 weeks of gestation from birth until term-equivalent age. Two-dimensional brainstem measurements of the pons and medulla oblongata were compared with those in a cohort of 67 healthy full-term newborns. Neurologic assessment of the premature infants was assessed at 5 years of age. Results: Of the 36 preterm infants born between 25 and 34 weeks of gestation, eight had significantly delayed growth profiles in both the pons and medulla and developed neurological sequelae by 5 years of age. Conclusions: Morphometric measurements of the developing brainstem using high resolution trans-foramen-magnum ultrasound (US) may help predict neurological outcome in high-risk neonates, particularly in those who are born extremely premature., Competing Interests: The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest., (Copyright © 2021 Chen, Hu, Tien and Chen.)

Objectives: Evaluation of bite force one, two, and four weeks after discharge following treatment of Le Fort I and/or Le Fort II fracture by rigid fixation and mandibulomaxillary fixation., Objective: The aim of this study was to evaluate bite force following treatment of Le Fort I and/or Le Fort II fractures by rigid fixation and mandibulomaxillary fixation at one, two, and four weeks after discharge. This provides valuable results to guide the development of a treatment protocol for Le Fort fractures., Method: This was a prospective study including 31 patients who underwent followup examination three times after being discharged from hospital. The examination evaluated bite force using a bite force meter in the right molar, left molar, and incisor regions., Results: One week after discharge, bite forces in the right molar, left molar, and incisor regions were 94.29 ± 58.80 N, 95.42 ± 57.34 N, and 39,94 ± 30,29 N, respectively. Two weeks after discharge, bite forces in the right molar, left molar, and incisor regions were 153.84 ± 89.14 N, 153.00 ± 78.55 N, and 65,9 ± 43.89 N, respectively. Four weeks after discharge, bite forces in the right molar, left molar, and incisor regions were 279.77 ± 95.46 N, 285.00 ± 90,47 N, and 123.42 ± 54.04 N, respectively., Conclusions: Bite forces in the right molar, left molar, and incisor regions were significantly increased one week, two weeks, and four weeks after discharge. Bite force may be a helpful parameter to confirm the stability of the midface bone after treatment of Le Fort fractures., Competing Interests: There are no conflicts of interest to declare., (© 2021 Doan-Van Ngoc, Le Hoai Phuc, Cao Huu Tien, Nguyen-Van Tuan, Le Trung Chanh, Lam Hoai Phuong, Nguyen Minh Duc.)

Background: We aimed to determine the minimum effective period of mandibulomaxillary fixation after the inadequate internal fixation of Le Fort I or Le Fort II fracture., Objective: The aim of this study was to investigate the stability of the skeleton after the treatment of Le Fort I or Le Fort II fractures by measuring bite forces and to determine the minimum time required for effective mandibulomaxillary fixation following treatment with internal fixation and mandibulomaxillary fixation., Method: A prospective study was performed to examine the treatment of Le Fort I or Le Fort II fracture in the Department of Maxillofacial Surgery at the National Hospital of Odonto-Stomatology in Ho Chi Minh City, Vietnam. A total of 31 patients were included, with up to 1 month of follow-up after discharge from the hospital. Midface bone stability and the mandibulomaxillary fixation time were evaluated using bite force criteria after 1, 2, and 4 weeks., Results: Midface bone stability values 1, 2, and 4 weeks after treatment were 87.1%, 100%, and 100%, respectively. After 1 week, 87.1% of patients achieved intermaxillary fixation, and 96.3% of these patients were treated with at least three rigid plates. The remaining 12.9% of patients achieved fixation after 2 weeks, and all of these patients were fixed only at zygomaticomaxillary sutures (p < 0.05). Bite forces increased significantly at 2 weeks compared with 1 week and at 4 weeks compared with 2 weeks (p < 0.05)., Conclusion: When treated using only rigid fixation, through the placement of plates and screws at zygomaticomaxillary buttresses, patients with Le Fort I and Le Fort II fractures can achieve mandibulomaxillary fixation after 2 weeks. For Le Fort I fractures, rigid fixation using plates and screws at zygomaticomaxillary buttresses and canine buttress at three positions can achieve mandibulomaxillary fixation after only 1 week (p = 0.0001)., Competing Interests: There are no conflicts of interest to declare., (© 2021 Le Hoai Phuc, Cao Huu Tien, Doan-Van Ngoc, Nguyen-Van Tuan, Le Trung Chanh, Lam Hoai Phuong, Nguyen Minh Duc.)

Interrupted reactions reroute established processes to new and often unanticipated end points. Of particular interest are the cases in which a known reactive intermediate takes on a new reaction pathway, either because this pathway is lower in energy or because the conventional pathway is no longer available. Through analysis of documented cases, we aim to dissect the known interrupted reactions and trace their mechanistic origins. As new chemical processes are being discovered at a seemingly ever-increasing pace, it is likely that new interrupted reactions will continue to emerge. Our hope is that the cases considered in this Review will help identify new classes of these fascinating transformations., (© 2021. Springer Nature Limited.)

Background: Stress hyperglycemia (SH) is considered a transient manifestation and routine diagnostic evaluation was thought to be unnecessary due to the lack of definite correlation with diabetes mellitus (DM). Although SH was usually benign and long-term treatment was superfluous, it might be the first sign of insulinopenic status such as type 1 DM (T1DM)., Case Presentation: We reported a boy with acute asthma attack presented incidentally with high blood glucose levels exceeding 300 mg/dL and obvious glycemic variability. A prolonged hyperglycemic duration of more than 48 h was also noticed. To elucidate his unique situation, glucagon test and insulin autoantibody survey were done which showed insulinopenia with positive anti-insulin antibody and glutamic acid decarboxylase antibody despite the absence of overt DM symptoms and signs., Conclusions: This case highlights that SH might be a prodromal presentation in T1DM children, especially when accompanied simultaneously with extreme hyperglycemia, apparent glucose variability, as well as prolonged hyperglycemic duration., (© 2021. The Author(s).)