Search

Eco-friendly solution processing and the low-cost synthesis of photoactive materials are important requirements for the commercialization of organic solar cells (OSCs). Although varieties of aqueous-soluble acceptors have been developed, the availability of aqueous-processable polymer donors remains quite limited. In particular, the generally shallow highest occupied molecular orbital (HOMO) energy levels of existing polymer donors limit further increases in the power conversion efficiency (PCE). Here, we design and synthesize two water/alcohol-processable polymer donors, poly[(thiophene-2,5-diyl)-alt-(2-((13-(2,5,8,11-tetraoxadodecyl)-2,5,8,11-tetraoxatetradecan-14-yl)oxy)-6,7-difluoroquinoxaline-5,8-diyl)] (P(Qx8O-T)) and poly[(selenophene-2,5-diyl)-alt-(2-((13-(2,5,8,11-tetraoxadodecyl)-2,5,8,11-tetraoxatetradecan-14-yl)oxy)-6,7-difluoroquinoxaline-5,8-diyl)] (P(Qx8O-Se)) with oligo(ethylene glycol) (OEG) side chains, having deep HOMO energy levels (similar to-5.4 eV). The synthesis of the polymers is achieved in a few synthetic and purification steps at reduced cost. The theoretical calculations uncover that the dielectric environmental variations are responsible for the observed band gap lowering in OEG-based polymers compared to their alkylated counterparts. Notably, the aqueous-processed all-polymer solar cells (aq-APSCs) based on P(Qx8O-T) and poly[(N,N '-bis(3-(2-(2-(2-methoxyethoxy)-ethoxy)ethoxy)-2-((2-(2-(2-methoxyethoxy)ethoxy)ethoxy)-methyl)propyl)naphthalene-1,4,5,8-bis(dicarboximide)-2,6-diyl)-alt-(2,5-thiophene)] (P(NDIDEG-T)) active layer exhibit a PCE of 2.27% and high open-circuit voltage (V-OC) approaching 0.8 V, which are among the highest values for aq-APSCs reported to date. This study provides important clues for the design of low-cost, aqueous-processable polymer donors and the fabrication of aqueous-processable OSCs with high V-OC.

Stress relaxation of high-density polyethylene is addressed both experimentally and theoretically. Two types of stress relaxation testing are carried out: uniaxial tensile testing at constant test specimen length and compression testing of a 3D structure producing inhomogeneous deformation fields and relaxation. A constitutive model for isotropic, semi-crystalline polymers is also proposed. The model has the ability to model stress relaxation at different time scales. The developed model was implemented as a user subroutine in Abaqus (UMAT). The implicit integration scheme including an algorithmic tangent modulus is described in detail. The material model is calibrated by use of the uniaxial tensile tests, and the model is then validated by simulating the compression tests of the 3D structure. The model is able to describe the uniaxial tension tests well, and the comparison between the simulations and experimental testing of the 3D structure shows very good agreement.

India is now poised to become one of the most important recycling hubs of the world. In the recent years, large-scale infrastructural set-up for sorting, processing, and recycling textiles has received attention. Additionally, with the positive policy intervention from the government, textile recyclers and sorters are now investing in modern technologies and exploring new business models to reshape this industry. This opens up opportunities for developing novel industrial value chains and ecosystems for valorising textile waste inter-continentally. This white paper serves a strategic insight document for all stakeholders associated with the quadruple helix of Indian textile recycling ecosystem, that is textile recycling sector, textile value chain players, governmental and financial institutions, academia, and special interest groups to vision the key strategic intervention areas and develop guidelines on future road mapping for designing a flourishing textile recycling ecosystem in India. We have addressed 4 dimensions for scaling textile recycling ecosystems and its underlying value chains, in terms of value chain optimization, supply-market strategic alignment, designing ecosystem sustainability and mobilizing external support to create a level playing field for value chain actors. 13 strategic intervention areas (SIAs) are identified where actions are required. To sum up: Value chain optimization calls for advancing existing technologies and building multi-technology flexible platforms to valorise diverse waste fractions. While legitimacy-building tools via certifications, standards and accreditations are crucial for brand image, of equal importance is supply network design for increasing effectiveness. Strategic alignment in textile recycling value chains for matching supply and demands, calls for improving market, customer and supply chain orientation, for enhancing value opportunities. While improved data generation and visibility will drive such market and, CLOSeD, RESORTEX

Effective individual wound management, particularly in cases of prolonged healing and increased infection vulnerability, has prompted the development of wound theranostics, combining real-time diagnostic assessment and on-demand treatment. Here, we present a multifunctional conducting polymer-based smart theranostic bandage that integrates pH sensing, pH-compensated uric acid (UA) biosensing, and on-demand antibiotic release using different conducting polymers, each leveraging their advantageous intrinsic properties. Specifically, the polyaniline-based pH sensor operates reversibly across a pH range of 4-10, while the functionalized poly(3,4-ethylenedioxythiophene)-based UA biosensor exhibits a linear response up to 0.9 mM UA. Simultaneous detection of pH and UA allows accurate UA determination via pH compensation. Upon detecting abnormal pH/UA levels, the polypyrrole-based drug carrier releases ciprofloxacin via 0.6 V electrical stimulation, successfully inhibiting bacterial growth in vitro. The array is assembled as a 3D patch, connected to a flexible printed circuit board, and embedded in a wound bandage, offering potential for remote wound monitoring, targeted treatment, and wireless wound management. Smart devices for wound management combine biosensing with drug release. Here, a smart theranostic bandage is reported that can detect pH and uric acid levels and release antibiotics as necessary, all of which can be done remotely., Funding Agencies|Sweden strategic research area Security Link; Chinese University of Hong Kong; Linkoping University

2D titanium carbide (Ti3C2) MXenes have emerged as promising candidates for biomedical applications. However, the biological properties of these materials are poorly understood. Moreover, MXenes are prone to oxidation under ambient conditions. Here, we show that glutathione (GSH), a natural antioxidant present in millimolar concentrations in the cytosol of most cells, protects MXenes from oxidation in aqueous suspensions while preserving the biocompatibility of the material. Reactive molecular dynamics (RMD) simulations confirm that GSH protects MXenes. Moreover, we provide evidence of the intracellular biotransformation of Ti3C2 MXenes to the rutile form of TiO2, and we show that GSH tunes the transformation process, resulting in the secretion of pro -inflammatory interleukin (IL) -1b through a non -canonical, elastase-dependent pathway. These results are important because they shed new light on the biotransformation of Ti3C2 MXenes and its ramifications for cellular signaling., Funding Agencies|Swedish Research Council [2021-04983]; Knut and Alice Wallenberg Foundation [KAW 2016.0057, KAW 2019.0433]; Goran Gustafsson Foundation for Research in Natural Sciences and Medicine; Swedish Research Council [2018-05973]

Global textile production and consumption has increased steadily over the past 15 years, which has caused significant impacts on the climate and the environment. In 2022, the EU launched a strategy for sustainable and circular textiles, stating that extending the life of textile products is the most efficient way to reduce their impact on the climate and the environment. Shell jackets for outdoor use are textile products that are frequently discarded by their first users and re-sold on the second-hand market. This study evaluates the performance of 16 second-hand shell jackets from three second-hand stores in Sweden via material testing of four key functional aspects. Comparing the results with the jackets’ original performance, this study describes the change in functionality over time. The results indicate that air permeability does not change significantly, whereas water repellency, water penetration resistance, and breathability decrease over time, although they do so at different rates. With the aim of promoting circularity and encouraging longer product use, this study also compares the price evolution of jackets with their functionality over time. The results reveal that the resale price of the jackets is lower than could be expected based on the level of remaining functionality in the jackets., Mistra Sport & Outdoors

This project aimed to broaden the knowledge of high-temperature polymers and composites when exposed to elevated temperatures and an oxygen-containing atmosphere. The main accent has been on thermosetting polyimide resins reinforced with carbon fibers. When subjected to harsh atmospheric conditions, such as elevated temperatures and oxygen, polymer resins can undergo thermo-oxidative degradation, often resulting in weight loss and a surface layer with altered properties. High-temperature composites could experience such environments during operation. Therefore, it is crucial to understand how exposure to it could affect their performance. To simulate such an environment in the lab, the materials are aged in a controlled manner in a furnace or other equipment. The ageing of polyimide composites in this project was often performed at temperatures at or above 288 degrees Celsius for extended periods of up to 1500 hours. The first part of the project, and the first article, delved into the effect of different layups and thicknesses of the carbon fiber bundles on the thermo-oxidative behaviour of two composite materials made with the same thermosetting polyimide. Modelling the desorption during the initial stages of the ageing, showed that it exhibited a Fickian behaviour. X-ray computed tomography experiments were used to investigate the ageing behaviour of the materials and revealed that the satin weave composite formed a network of cracks, voids, and delaminations, that progressed with the ageing time, while the damage in the material made of thin plies was in the form of delaminations at the edges. The analysis of the tomographic datasets was performed using Otsu’s thresholding method for semantic segmentation of the defects within the materials. In an attempt to counter the crack formation on the surface of the satin weave composite observed during the first study, a new polyimide formulation was developed by the manufacturer. The amount of internal crosslinkers was

Lightweight and mechanically robust hybrid foams based on cellulose nanocrystals (CNC) and multi-walled carbon nanotubes (MWCNT) with an anisotropic structure are prepared by directional ice-templating. The anisotropic hybrid CNC-MWCNT foams displayed a combination of highly anisotropic thermal conductivity and an orientation-dependent electromagnetic interference (EMI) shielding with a maximum EMI shielding efficiency (EMI-SE) of 41–48 dB between 8 and 12 GHz for the hybrid foam with 22 wt% MWCNT. The EMI-SE is dominated by absorption (SEA) which is important for microwave absorber applications. Modelling of the low radial thermal conductivity highlighted the importance of phonon scattering at the heterogeneous CNC-MWCNT interfaces while the axial thermal conductivity is dominated by the solid conduction along the aligned rod-like particles. The lightweight CNC-MWCNT foams combination of an anisotropic thermal conductivity and EMI shielding efficiency is unusual and can be useful for directional heat transport and EMI shielding.

Prolonging garment longevity is a well-recognized key strategy to reduce the overall environmental impact in the textile and clothing sector. In this context, change or degradation in esthetic or visual appeal of a garment with usage is an important factor that largely influence its longevity. Therefore, to engineer the garments for a required lifetime or prolong longevity, there is a need for predictive systems that can forecast the trajectory of visual degradation based on material/structural parameters or use conditions that can guide the practitioners for an optimal design. This paper develops a deep learning based predictive system for washing-induced visual change or degradation of selected garment areas. The study follows a systematic experimental design to generate and capture visual degradation in garment and equivalent fabric samples through 70 cycles in a controlled environment following guideline from relevant washing standards. Further, the generated data is utilized to train conditional Generative Adversarial Network-based deep learning model that learns the degradation pattern and links it to washing cycles and other seam properties. In addition, the predicted results are compared with experimental data using Frechet Inception Distance, to ascertain that the system prediction are visually similar to the experimental data and the prediction quality improves with training process.

This report is as a part of the research project Sustainable clothing futures, and have, through literature and market studies and interviews, identified actors working with sorting and recycling of textiles, with capacities of 560 000 tons and 1.3 million tons per year, respectively. In the interviews, it was clear that an up scale of the capacities is possible, but is depending on several factors, technological development amongst others., Denna rapport är en del av forskningsprojektet Framtidens Hållbara Kläder och har genom litteratur- och marknadsstudier samt intervjuer kartlagt aktörer som arbetar med sortering och återvinning av post-konsument-textil. Totalt har 12 sorterare och 33 återvinnare kartlagts, med kapaciteter på 560 000 ton respektive 1.3 miljoner ton per år. Under intervjuerna framkom det att uppskalning kapaciteterna är möjligt, men att det är beroende av olika faktorer, bland annat att tekniken behöver utvecklas.

Plastic packaging constitutes a large part of the total plastic use in Sweden. However, only a limited fraction of all packaging put on the Swedish market each year is recycled. One of the reasons for this is the complex design of many plastic packages, which contributes to challenges when sorting, disassembling, and recycling the collected material into high-value applications. Flexible plastic packaging, namely films, used for packaging groceries/food are especially challenging when it comes to mechanical recycling. This category includes countless multi-layered film structures which often include, for example, barriers and adhesives that may affect the sorting and recycling of the material. The aim of the first work package was to conduct an initial market analysis to map and quantify the current and future use of complex high barrier laminates, both multi-material structures and mono-materials structures, on the Swedish market. The market analysis was carried out by studying available literature, both scientific and grey literature, as well as through interviews with relevant stakeholders.

The human body is a complex system, consisting of different types of biomolecules and living matters, such as nucleic acids, proteins, carbohydrates, lipids, serum, cells, tissues, and organs. These complex biomolecules and living matters integrate and interact dynamically to perform and maintain body functions. However, it is very difficult to study these biomaterials in vivo due to intricated relationship of biomaterials within complex body systems. Thus, researchers usually conduct an initial in-depth analysis of substances in vitro, then apply them in vivo for disease treatments or tissue repair. Recently, Hara et al. had a fantastic finding that chondrocyte-derived plasma membrane nanofragments (PMNFs) can induce bone-like tissue in vitro for only two days, while live cells or other biomaterials require at least 2-4 weeks. This effect of PMNFs is highly desirable, particularly for those elderly with osteoporosis and those with bone injuries who require rapid bone growth and repair. Recent studies have increasingly supported the notion that some non-biological materials provide important microenvironmental cues to support the activity of cells in in vitro conditions or within tissues. Based on these, living matters or biomolecules can be combined with or incorporated within specific non-biological material to create a microenvironment that further enhances cellular functions toward, for instance, combating infections and cancers or promoting tissue repair. In these cases, the materials combining biomolecules and/or living matters with non-biological materials are called biohybrid materials. Conducting polymers, e.g., polypyrrole (PPy), have become a class of promising non-biological material for the development of biohybrid materials due to their good biocompatibility, electronic/ionic conductivity, reversible volume change and switchable surface properties. Thus, in this thesis, we developed biohybrid material-based devices by the combination of PMNFs and PPy f, Människokroppen är ett komplext system som består av olika typer av biomolekyler och levande ämnen, såsom nukleinsyror, proteiner, kolhydrater, lipider, serum, celler, vävnader och organ. Dessa komplexa biomolekyler och levande ämnen integreras och interagerar dynamiskt för att utföra och upprätthålla kroppsfunktioner. Det är dock mycket svårt att studera dessa biomaterial in vivo på grund av det invecklade förhållandet mellan biomaterial inom komplexa kroppssystem. Således gör forskare vanligtvis en inledande djupgående analys av ämnen in vitro och applicerar dem sedan in vivo för sjukdomsbehandlingar eller vävnadsreparation. Nyligen har Hara et al. hade en fantastisk upptäckt att kondrocythärledda plasmamembrannanofragment (PMNF) kan inducera benliknande vävnad in vitro i endast två dagar, medan levande celler eller andra biomaterial kräver minst 2-4 veckor. Denna effekt av PMNF är mycket önskvärd, särskilt för de äldre med osteoporos och de med benskador som kräver snabb bentillväxt och -reparation. Nyligen genomförda studier har alltmer stött uppfattningen att vissa icke-biologiska material tillhandahåller viktiga mikromiljömässiga signaler för att stödja aktiviteten hos celler under in vitro-förhållanden eller i vävnader. Baserat på dessa kan levande ämnen eller biomolekyler kombineras med eller inkorporeras i specifikt icke-biologiskt material för att skapa en mikromiljö som ytterligare förbättrar cellulära funktioner mot till exempel att bekämpa infektioner och cancer eller främja vävnadsreparation. I dessa fall kallas de material som kombinerar biomolekyler och/eller levande ämnen med icke-biologiska material för biohybridmaterial. Ledande polymerer, t.ex. polypyrrol (PPy), har blivit en klass av lovande icke-biologiska material för utveckling av biohybridmaterial på grund av deras goda biokompatibilitet, elektroniska/joniska konduktivitet, reversibla volymförändringar och omkopplingsbara ytegenskaper. I detta examensarbete har vi därför utvecklat biohybridm

The biological deterioration of archaeological wood under oxygen-limited conditions varies due to the limited activities of microorganisms. It is essential to expand the knowledge of the degradation types and the status of archaeological monuments for selecting the proper consolidates. The physical, chemical, and anatomical properties of approximately 600–650 year old archaeological oak collected from an archaeological site in Iasi-Romania were analysed to assess the quality and to identify the degradation types. The results were compared with similar tests on recently-cut oak. X-ray photoelectron spectroscopy (XPS) revealed the presence of more lignin-related peaks in the archaeological oak, which likely reflected the degradation of the wood carbohydrates as evidenced by the decreased oxygen-to-carbon ratio Cox/Cnon-ox. The differences in cellulose crystallinity were not significant suggesting that any cellulose degradation occurred in the amorphous regions. This was also reflected in the dynamic water vapor sorption analysis where the differences in sorption isotherms and hysteresis of archaeological and recently-cut oaks were marginal. Microscopic analysis of the oak cells illustrated bacterial degradation patterns, while the field emission scanning electron microscopy (FESEM) showed the presence of erosion bacteria in the archaeological oak collected from the site with low oxygen conditions.

This Executive Brief compiles the key results obtained from some ongoing research and innovation studies conducted with the scope of two ongoing projects: (i) CLOSeD (Circular clothing dichotomies in global-local supply chain dispersion) funded by Ikea Family Research Foundation; ongoing since January 2021, and (ii) Circular Logistics (Exploring the role of logistics in the circular textile ecosystem) funded by Formas (Swedish research council for sustainable development); ongoing since May 2022. [More about the 2 projects here: CLOSeD↗ Circular Logistics↗] This Executive Brief is one-of-its-kind, given that it synthesizes the results of multiple ongoing studies, and draws connection among them by presenting an overarching purpose of creating science-based logical reasoning and understanding of how circular clothing supply chains and ecosystems, and the organizations embedded within, can maximise their valorisation potential amid the changing landscape led by, for example, the European Union (EU)-wide planning and adoption of “EU Strategy for textiles”. A common thread of our argument, as put forward in this Executive Brief is while the textile circular economy is largely influenced in practice by recent technological advancements, related to circular material development, innovative products and processes, or digitalization of circular business models and operations, the motivation in driving them forward has been largely from an efficiency-gain perspective, both in terms of economics and ecology, that is address whether and how circular economy would minimise costs, enhance profitability, and render economies of scale. A novelty-centred perspective has been largely implicit in this regard; however critical to generate a top-line on how circular supply chains and ecosystems should generate sustainable value, beyond cost/profit dimensions. To address this our Executive Brief presents the 5 distinct studies’ results. Each study is enriched by empirically-driven da

The report describes a project aimed at finding a way to warm a seat. Etac, one of the leading manufacturers and developers of disability aids has received feedback from customers that the shower seats they produce are cold when the user has just sat down. This seemed to the user that showering is associated with inconvenience. To answer the purpose, 3 questions were formulated. To get more understanding of the task, a feasibility study was carried out and various methods were used during the development process. A market survey has been carried out, various solution proposals have been developed and then a test survey was carried out on the concepts that have been developed. As a result of the project, 3 concept proposals have been produced., Rapporten beskriver ett projekt som syftar till att hitta ett sätt att värma en sits. Etacsom är ett av ledande tillverkare och utvecklare av funktionshindrade hjälpmedel har fått feedback av kunder att duschstolarna de tillverkar är kalla när brukaren precis har satt sig ner. Detta tycktes brukaren att duschandet förknippas med besvär.För att kunna besvara syftet så utformades 3 frågeställningar. För att få mer förståelse på uppgiften så gjordes en förstudie, olika metoder har använts under utvecklingsprocessen. Det har gjorts en marknadsundersökning, olika lösningförslag har tagits fram därefter gjordes en testundersöknings på de koncept som har tagits fram. Som resultat på projektet har 3 konceptförslag framställts.

There are many bioelectronic applications where the additive manufacturing of conductive polymers may be of use. This method is cheap, versatile and allows fine control over the design of wearable electronic devices. Nanocellulose has been widely used as a rheology modifier in bio-based inks that are used to print electrical components and devices. However, the preparation of nanocellulose is energy and time consuming. In this work an easy-to-prepare, 3D-printable, conductive bio-ink; based on modified cellulose fibers and poly(3,4-ethylene dioxythiophene) poly(styrene sulfonate) (PEDOT:PSS), is presented. The ink shows excellent printability, the printed samples are wet stable and show excellent electrical and electrochemical performance. The printed structures have a conductivity of 30 S/cm, high tensile strains (>40%), and specific capacitances of 211 F/g; even though the PEDOT:PSS only accounts for 40 wt% of the total ink composition. Scanning electron microscopy (SEM), wide-angle X-ray scattering (WAXS), and Raman spectroscopy data show that the modified cellulose fibers induce conformational changes and phase separation in PEDOT:PSS. It is also demonstrated that wearable supercapacitors and biopotential-monitoring devices can be prepared using this ink., QC 20230208

Soft robotics has attracted great attention owing to their immense potential especially in human-robot interfaces. However, the compliant property of soft robotics alone, without stiff elements, restricts their applications under load-bearing conditions. Here, biohybrid soft actuators, that create their own bone-like rigid layer and thus alter their stiffness from soft to hard, are designed. Fabrication of the actuators is based on polydimethylsiloxane (PDMS) with an Au film to make a soft substrate onto which polypyrrole (PPy) doped with poly(4-styrenesulfonic-co-maleic acid) sodium salt (PSA) is electropolymerized. The PDMS/Au/PPy(PSA) actuator is then functionalized, chemically and physically, with plasma membrane nanofragments (PMNFs) that induce bone formation within 3 days, without using cells. The resulting stiffness change decreased the actuator displacement; yet a thin stiff layer couldnot completely stop the actuators movement, while a relatively thick segment could, but resulted in partial delamination the actuator. To overcome the delamination, an additional rough Au layer was electroplated to improve the adhesion of the PPy onto the substrate. Finally, an alginate gel functionalized with PMNFs was used to create a thicker mineral layer mimicking the collagen-apatite bone structure, which completely suppressed the actuator movement without causing any structural damage., Funding Agencies|Japanese Society of the Promotion of Science, JSPS [BR170502]; KAKENHI [JP20H04534]; Japan Science and Technology Agency, JST; Swedish Research Council [F17603]; Promobilia Foundation [201808330454]; China Scholarship Council [JPJSBP 120209923]; JSPS [MG2019-8171]; STINT; Swedish Foundation for International Cooperation in Research and Higher Education [JPMJFR210X]; [VR2014-3079]

Cellulose-based electro-actuators have enormous potential in various applications, e.g. artificial muscles, soft grippers, medical devices, just to name a few, owing to their high mechanical strength, lightness and natural abundance. However, significant challenges remain in the fabrication of such electro-actuators featuring low operating voltage and fast response kinetics. We report here a facile fabrication route towards high-performance electro-actuators composed of CNFs films doped with ionic liquids or lithium salts and sandwiched by two thin film gold electrodes. Large bending motion at voltages as low as 3.0 V could be observed. The size effect of both anions and cations on the actuation was comprehensively investigated. CNF-TFSI@LiTFSI and CNF-BF4@EMIM-BF4 electro-actuators presented the best bending strain under an AC voltage of 3.0 V. This work provides new inspiration in the design of natural polymer-based high-performance electro-actuators.

Direct ink writing (DIW) is a promising additive manufacturing (AM) technique in the field of microsystems technology due to the potential for high detail resolution and the wide choice of materials suitable for the technique. In this study, inks of polyvinylidene fluoride-trifluoroethylene (PVDF-TrFE) as well as composite inks with reduced graphene oxide (PVDF-TrFE-rGO) were developed and adapted for continuous flow DIW. The composite PVDF-TrFE-rGO inks achieved percolation after 1.5 wt% and electrical conductivity of 2.8 S/cm at the highest loading investigate in this study (7 wt%). The inks were successfully printed with minimum nozzle diameter of 40 & mu;m on different substrates including glass, metal and a nitrile elastomer. It was also demonstrated that the inks can be used to create a fully 3D-printed piezoelectric device with the predicted response, i.e. the fabrication technique did not deteriorate the functionality of the device. The conductive composite ink was successfully utilized as an effective electrode in the device. It was therefore demonstrated that by combining materials, such as the composite PVDF-TrFE-rGO ink and the co-polymer PVDF-TrFE with additive manufacturing techniques, the fabrication of low-cost, versatile devices can be achieved.

This study aimed to develop a manufacturing process for recycled textile long fiber thermoplastics (RT-LFT) and thereby contribute to circular economy. Three different post-consumer textiles (cotton denim and plain weave, and silk plain weave) were cut into strips and fed directly into a co-rotating twin-screw extruder in which the textile was fibrillated and compounded with polypropylene (PP). The fibrillation of the textile, fiber dispersion, and interaction with the matrix polymer were studied, and the thermal and mechanical properties of the composites were evaluated. For example, cotton denim composites containing 30 wt% fiber content resulted in 26% increase in yield strength and a 72% increase in modulus when compared with that of PP. The RT-LFT process is a straightforward method for transforming used textiles into composites like cups and bottoms, offering advantages such as reduced manufacturing costs, add value for waste material, and lower carbon emissions., Validerad;2023;Nivå 2;2023-09-22 (joosat);CC BY 4.0 License

Graphene oxide (GO), chemically expanded graphite (CEG) and graphite were evaluated as solid lubricant for ultrahigh molecular weight polyethylene composites. Under dry conditions, the addition of all solid lubricants increased the coefficient of friction by up to 38%. For the composites corrugated stick–slip features were observed which correlate with a decrease in matrix degree of crystallinity. GO had the lowest effect on the crystallisation, resulting in the lowest relative increase in friction coefficient of only 13%. Under water lubrication, GO, CEG and graphite were equally effective in reducing friction and wear. The highest friction for the neat matrix was found to be due to a transfer film, which was suppressed by the addition of the solid lubricants., Validerad;2023;Nivå 2;2023-06-26 (hanlid)

Purpose: To compare fixed transverse textile electrodes (TTE) knitted into a sock versus motor point placed standard gel electrodes (MPE) on peak venous velocity (PVV) and discomfort, during calf neuromuscular electrical stimulation (calf-NMES). Methods: Ten healthy participants received calf-NMES with increasing intensity until plantar flexion (measurement level I = ML I), and an additional mean 4 mA intensity (ML II), utilizing TTE and MPE. PVV was measured with Doppler ultrasound in the popliteal and femoral veins at baseline, ML I and II. Discomfort was assessed with a numerical rating scale (NRS, 0–10). Significance was set to p < 0.05. Results: TTE and MPE both induced significant increases in PVV from baseline to ML I and significantly higher increases to ML II, in both the popliteal and femoral veins (all p < 0.001). The popliteal increases of PVV from baseline to both ML I and II were significantly higher with TTE versus MPE (p < 0.05). The femoral increases of PVV from baseline to both ML I and II were not significantly different between TTE and MPE. TTE versus MPE resulted at ML I in higher mA and NRS (p < 0.001), and at ML II in higher mA (p = 0.005) while NRS was not significantly different. Conclusion: TTE integrated in a sock produces intensity-dependent increases of popliteal and femoral hemodynamics comparable to MPE, but results in more discomfort at plantar flexion due to higher current required. TTE exhibits in the popliteal vein higher increases of PVV compared to MPE. Trial registration: Trial_ID: ISRCTN49260430. Date: 11/01/2022. Retrospectively registered.

We report a reliable and scalable fabrication method for producing electrical contacts to two-dimensional (2D) materials based on the tri-layer resist system. We demonstrate the applicability of this method in devices fabricated on epitaxial graphene on silicon carbide (epigraphene) used as a scalable 2D material platform. For epigraphene, data on nearly 70 contacts result in median values of the one-dimensional (1D) specific contact resistances pc 67 omega center dot im and follow the Landauer quantum limit pc n-1/2, consistently reaching values pc < 50 omega center dot im at high carrier densityn. As a proof of concept, we apply the same fabrication method to the transition metal dichalcogenide (TMDC) molybdenum disulfide (MoS2). Our edge contacts enable MoS2 field-effect transistor (FET) behavior with an ON/OFF ratio of >106 at room temperature (>109 at cryogenic temperatures). The fabrication route demonstrated here allows for contact metallization using thermal evaporation and also by sputtering, giving an additional flexibility when designing electrical interfaces, which is key in practical devices and when exploring the electrical properties of emerging materials., Funding Agencies|Swedish Foundation for Strategic Research (SSF) [GMT14-0077, RMA15-0024, FFL21-0129]; Chalmers Area of Advance Nano, Chalmers Area of Advance Energy, 2D TECH VINNOVA competence Center [2019-00068]; Marie Sklodowska-Curie [766025]; Knut and Alice Wallenberg Foundation [2019.0140]; Swedish Research Council VR [2021-05252, 2018-04962]

Smart textiles combine the features of conventional textiles with promising properties of smart materials such as electromechanically active polymers, resulting in textile actuators. Textile actuators comprise of individual yarn actuators, so understanding their electro-chemo-mechanical behavior is of great importance. Herein, this study investigates the effect of inherent structural and mechanical properties of commercial yarns, that form the core of the yarn actuators, on the linear actuation of the conducting-polymer-based yarn actuators. Commercial yarns were coated with poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) to make them conductive. Then polypyrrole (PPy) that provides the electromechanical actuation is electropolymerized on the yarn surface under controlled conditions. The linear actuation of the yarn actuators is investigated in aqueous electrolyte under isotonic and isometric conditions. The yarn actuators generated an isotonic strain up to 0.99% and isometric force of 95 mN. The isometric strain achieved in this work is more than tenfold and threefold greater than the previously reported yarn actuators. The isometric actuation force shows an increase of nearly 11-fold over our previous results. Finally, a qualitative mechanical model is introduced to describe the actuation behavior of yarn actuators. The strain and force created by the yarn actuators make them promising candidates for wearable actuator technologies. © 2023 The Authors. Advanced Materials Technologies published by Wiley-VCH GmbH.

As robots more frequently fraternize with humans in everyday life, aspects such as safety, flexibility of tasks, and appearance become increasingly important. Soft robotics is attractive for new human-close applications, but soft actuators constitute a major challenge both in terms of actuation force and speed, and in terms of control and accuracy of the deformable soft actuator body. Herein, several of these challenges are addressed by developing versatile ultrasoft electromagnetic actuators that operate in absence of external magnetic fields, while simultaneously monitoring their states by internal strain sensors. The versatile actuators can compress to less than 50% of their initial length with strain-independent contraction force and operate in both contraction and expansion modes up to 200 Hz frequency while conforming to curved surfaces. The soft multilayer conductive cellulose-based foams are lightweight (3 mg cm(-3)) and provide internal strain-sensing capability and structural support, thereby improving the monitoring and controllability of the actuators while maintaining an axial softness of 0.6 kPa. It is believed that the concept of soft versatile electromagnetic actuators with integrated lightweight strain-sensing foams is promising for a wide range of applications within soft robotics., Funding Agencies|Knut and Alice Wallenberg Foundation, Linkoping University, and industry through the Wallenberg Wood Science Centre; Swedish Government Strategic Research Area in Materials Science on Advanced Functional Materials at Linkoping University [2009-00971]

Stretchable organic electrochemical transistors (OECTs) are promising for wearable applications within biosensing, bio-signal recording, and addressing circuitry. Efficient large-scale fabrication of OECTs can be performed with printing methods but to date there are no reports on high-performance fully printed stretchable OECTs. Herein, this challenge is addressed by developing fully screen-printed stretchable OECTs based on an architecture that minimizes electrochemical side reactions and improves long-term stability. Fabrication of the OECTs is enabled by in-house development of three stretchable functional screen-printing inks and related printing processes. The stretchable OECTs show good characteristics in terms of transfer curves, output characteristics, and transient response up to 100% static strain and 500 strain cycles at 25% and 50% strain. The strain insensitivity of the OECTs can be further improved by strain conditioning, resulting in stable performance up to 50% strain. Finally, an electrochromic smart pixel is demonstrated by connecting a stretchable OECT to a stretchable electrochromic display. It is believed that the development of screen-printed stretchable electrochemical devices, and OECTs in particular, will pave the way for their use in wearable applications and commercial products., Funding Agencies|Swedish Foundation for Strategic Research; Swedish Government Strategic Research Area in Materials Science on Advanced Functional Materials at Linkoping University [2009-00971]

In the present study, polycaprolactone/polyethylene glycol (PCL/PEG) electrospun nanofibres with different anthocyanin (1%, 2%, 3%, and 5%) were fabricated for the instant measurement of pH, especially for applications—such as food freshness detection—where quick response is required. The solution, surface, chemical, thermal, wettability, mechanical, and release properties of the samples were evaluated by viscosity measurements, scanning electron microscopy (SEM), Fourier-transform infrared (FTIR), contact angle measurements, and tensile tests, respectively. The colorimetric analyses were also investigated against the solutions at different pH values and bacterial solutions. Finally, the on-site performance of the sensor was evaluated. Anthocyanin addition initially lowered the solution viscosity, resulting in thinner fibres with a diameter of 288 nm. The diameters were increased up to 395 nm with the increasing anthocyanin. Anthocyanin addition enhanced the wettability and the mechanical properties, and the contact angles decreased to 43°. The highest modulus was observed for 1% anthocyanin, with a value of 6.162. The release experiments revealed that the anthocyanin-loaded samples released a large amount of anthocyanin (between ~12% and 38%) in the first 15 s. The colorimetric analyses showed that PCL/PEG nanofibre mats with 2% and 3% anthocyanin concentrations were the most capable pH-sensitive sensors for detecting pH changes from 2 to 8. As a result, it can be concluded that 3% anthocyanin is the threshold value for the production of the anthocyanin-loaded nanofibre mats, and these structures are promising for the instant detection of pH proved by the on-site application.

Purpose Physical inactivity is associated with muscle atrophy and venous thromboembolism, which may be prevented by neuromuscular electrical stimulation (NMES). This study aimed to investigate the effect on discomfort, current amplitude and energy consumption when varying the frequency and phase duration of low-intensity NMES (LI-NMES) via a sock with knitting-integrated transverse textile electrodes (TTE). Methods On eleven healthy participants (four females), calf-NMES via a TTE sock was applied with increasing intensity (mA) until ankle-plantar flexion at which point outcomes were compared when testing frequencies 1, 3, 10 and 36 Hz and phase durations 75, 150, 200, 300 and 400 µs. Discomfort was assessed with a numerical rating scale (NRS, 0–10) and energy consumption was calculated and expressed in milli-Joule (mJ). Significance set to p ≤ 0.05. Results 1 Hz yielded a median (inter-quartile range) NRS of 2.4 (1.0–3.4), significantly lower than both 3 Hz with NRS 2.8 (1.8–4.2), and 10 Hz with NRS 3.4 (1.4–5.4) (both p ≤ .014). Each increase in tested frequency resulted in significantly higher energy consumption, e.g. 0.6 mJ (0.5–0.8) for 1 Hz vs 14.9 mJ (12.3–21.2) for 36 Hz (p = .003). Longer phase durations had no significant effect on discomfort despite generally requiring significantly lower current amplitudes. Phase durations 150, 200 and 400 µs required significantly lower energy consumption compared to 75 µs (all p ≤ .037). Conclusion LI-NMES applied via a TTE sock produces a relevant plantar flexion of the ankle with the best comfort and lowest energy consumption using 1 Hz and phase durations 150, 200 or 400 µs.

QC 20230911

Congo red (CR) dye is a synthetic azo dye expansively used in the textile industry, is discharged to aquatic environments, and is toxic to humans and aquatic flora. The performance of cationic amino-modified banana leaves (CMBL) for CR dye sequestration was evaluated first time in this study. The surface modification of CMBL was analyzed using Scanning electron microscope (SEM) and Fourier transform infrared (FTIR) spectrum and compared with raw banana leaves powder (RBL). The optimum condition for CR dye adsorption using CMBL was optimized using Central Composite Design (CCD) by investigating four critical operating parameters: contact time, pH, RBL/CMBL doses, and initial CR dye concentrations. The proposed model (quadratic) was acceptable due to the high values of correlation coefficients R2 (0.96) and adjusted R2 (0.92). The CMBL exhibited maximum removal efficiency of 76.82% towards CR dye at pH 3 compared to RBL, i.e., 19.63%. Electrostatic interaction and hydrogen bonding were the primary removal mechanisms for the CR dye adsorption process using CMBL. Freundlich isotherm and pseudo-second-order kinetic model exhibited a strong correlation for experimental data and reported a correlation coefficient (R2) of more than 0.99. In addition, CMBL showed excellent reusability for the adsorption of CR dye even after three consecutive adsorption-desorption experiments., QC 20230913

New sustainable materialsproduced by green processing routes arerequired in order to meet the concepts of circular economy. The replacementof insulating materials comprising flammable synthetic polymers bybio-based materials represents a potential opportunity to achievethis task. In this paper, low-density and flame-retardant (FR) porousfiber networks are prepared by assembling Layer-by-Layer (LbL)-functionalizedcellulose fibers by means of freeze-drying. The LbL coating, encompassingchitosan and sodium hexametaphosphate, enables the formation of aself-sustained porous structure by enhancing fiber-fiber interactionsduring the freeze-drying process. Fiber networks prepared from 3 Bi-Layer(BL)-coated fibers contain 80% wt of cellulose and can easily self-extinguishthe flame during flammability tests in vertical configuration whiledisplaying extremely low combustion rates in forced combustion tests.Smoke release is 1 order of magnitude lower than that of commerciallyavailable polyurethane foams. Such high FR efficiency is ascribedto the homogeneity of the deposited assembly, which produces a protectiveexoskeleton at the air/cellulose interface. The results reported inthis paper represent an excellent opportunity for the developmentof fire-safe materials, encompassing natural components where sustainabilityand performance are maximized., QC 20230810

The lifespan and the performance of flexible electronic devices and components are affected by the large accumulation of heat, and this problem must be addressed by thermally conductive polymer composite films. Therefore, the need for the development of high thermal conductivity nanocomposites has a strong role in various applications. In this article, the effect of different particle reinforcements such as single and hybrid form, coated and uncoated particles, and chemically treated particles on the thermal conductivity of various polymers are reviewed and the mechanism behind the improvement of the required properties are discussed. Furthermore, the role of manufacturing processes such as injection molding, compression molding, and 3D printing techniques in the production of high thermal conductivity polymer composites is detailed. Finally, the potential for future research is discussed, which can help researchers to work on the thermal properties enhancement for polymeric materials., Validerad;2023;Nivå 2;2023-08-15 (marisr);License fulltext: CC-BY. This is an open access article under the terms of the Creative Commons Attribution License, which permits use, distribution and reproduction in any medium, provided the original work is properly cited.

The environmental burden of the textile industry can be decreased with an increased use of mechanically recycled fibers. However, it is well known that the recycling process is harsh and shortens the fibers substantially. Still, little has been investigated about the influencing factors of the fiber length loss. Previous research has shown that the parts of a garment that is more worn, lose less fiber length in the mechanical recycling process.1 One explanation could be that a loss of fibers during wearing create a more open structure of the textile. By removing fibers from the yarns in a textile, the yarn structure is partly broken down, and the yarn linear density is decreased. The strength of spun staple fiber yarns is dependent on the friction and contact surfaces between fibers. In addition, fiber migration, the variation of radial position of a fiber in the yarn, causes the fibers to lock between different helical layers and thus creates a self-locking mechanism giving strength to the yarn.2 Removal of any fiber in such a yarn affect all fibers in contact with that fiber. This in turn makes both the textile and yarns weaker and consequently more easily disentangles in a mechanical recycling process – keeping more of the fiber length. The work at hand investigated this theory by subjecting woven cotton textiles with abrasion treatment prior to mechanical recycling. We compared two different methods of abrasion with unabraded textile. The two pre-treatment abrasion methods used were rubbing with sandpaper and raising with steel pins. By measuring the fiber length post mechanical recycling, we could estimate the efficiency of the recycling process in respect to preservation of the fiber. Results showed that only the raising process had a positive impact in mitigating fiber length loss through the recycling process. During the rubbing with sandpaper, the fabric was pressed and thus became denser. On the contrary, the raising process pulled out the fibers and cr

Soft vibrotactile devices have the potential to expandthe functionalityof emerging electronic skin technologies. However, those devices oftenlack the necessary overall performance, sensing-actuation feedbackand control, and mechanical compliance for seamless integration onthe skin. Here, we present soft haptic electromagnetic actuators thatconsist of intrinsically stretchable conductors, pressure-sensitiveconductive foams, and soft magnetic composites. To minimize jouleheating, high-performance stretchable composite conductors are developedbased on in situ-grown silver nanoparticles formed within the silverflake framework. The conductors are laser-patterned to form soft anddensely packed coils to further minimize heating. Soft pressure-sensitiveconducting polymer-cellulose foams are developed and integrated totune the resonance frequency and to provide internal resonator amplitudesensing in the resonators. The above components together with a softmagnet are assembled into soft vibrotactile devices providing high-performanceactuation combined with amplitude sensing. We believe that soft hapticdevices will be an essential component in future developments of multifunctionalelectronic skin for future human-computer and human-roboticinterfaces.

Nowadays, the soar of photovoltaic performance of perovskite solar cells has set off a fever in the study of metal halide perovskite materials. The excellent optoelectronic properties and defect tolerance feature allow metal halide perovskite to be employed in a wide variety of applications. This article provides a holistic review over the current progress and future prospects of metal halide perovskite materials in representative promising applications, including traditional optoelectronic devices (solar cells, light-emitting diodes, photodetectors, lasers), and cutting-edge technologies in terms of neuromorphic devices (artificial synapses and memristors) and pressure-induced emission. This review highlights the fundamentals, the current progress and the remaining challenges for each application, aiming to provide a comprehensive overview of the development status and a navigation of future research for metal halide perovskite materials and devices., Funding Agencies|National Key Research and Development Program of China [2022YFB3803300]; open research fund of Songshan Lake Materials Laboratory [2021SLABFK02]; National Natural Science Foundation of China [21961160720]

To produce a greener adhesive is always an issue of concern to the commercial market and global environment. The environmental request for producing greener and bio-based adhesives leads to an increased awareness of replacing fossil-based components in adhesives with bio-based alternatives. Consequently, many researchers try to graft polymers from natural materials and some achievements have been made. In this work, an improved procedure to graft vinyl acetate (VAc) from chitosan (CS) is proposed and significant improvements were made regarding the increased Tg and water resistance. The achieved monomer conversion of VAc was ~97 %, and it was confirmed that chitosan-graft-poly(vinyl acetate) (CS-g-PVAc) could be used as a wood adhesive. The adhesive exhibited competitive properties to commercial PVAc wood adhesive. In the produced CS-g-PVAc, ~17 % of the fossil-based content of VAc could be replaced with bio-based chitosan, indicating an increased sustainability. At the same time there is no residual monomer during pressing, which avoid to pollute environment and hurt human. Compared to commercial PVAc, which has Tg at ~28 ℃, the Tg of CS-g-PVAc is ~42 ℃ At the same time, the water resistance of PVAc adhesive was successfully increased.

Nanopartiklar (NP) erbjuder unika möjligheter för medicinska tillämpningar, inklusive kontrollerad frisättning av cancerläkemedel, användning som bildkontrast vid avbildningsprocedurer eller hypertermisk behandling av cancerceller. Flash nanoprecipitation (FNP) producerar NPs för att kombinera dessa tillämpningar i en snabb, billig och skalbar beläggningsprocess. Användning av FNP med en Multi-Inlet Vortex Mixer (MIVM) är en lovande metod för att enkelt belägga hydrofoba oljesyra järnoxid NP (IONP) med olika biokompatibla block-copolymerer. Amfifila block-copolymerer baserade på hydrofil polyetylenglykol (PEG) och hydrofob poly(laktid) (PLA), poly(laktid-co-glykolid) (PLGA) eller poly(kaprolakton) (PCL) syntetiserades framgångsrikt. Den organiska katalysatorn 1,8-diazabicyclo[5.4.0]undec-7-en (DBU) användes för att öka biokompatibiliteten hos de resulterande polymererna PEG-PLA, PEG-PL7,5KG2,5KA och PEG2K-PCL2K. Syntes av hydroxylterminerad poly(akrylsyra) (PAA-OH) följt av polymerisation med PLGA prövades. De amfifila blockpolymererna användes i kombination med stabilisatorn polysorbat 80 (Tween80®) i FNP för att bilda nakna polymera NP med en MIVM som reaktor. DLS och STEM bekräftade partikelstorlekar mellan 50 - 100 nm. Tillsatsen av 13 ± 2 nm hydrofoba oljesyra-IONPs gav en ökning av partikelstorleken samt en ökning av partikelstabiliteten över tid. STEM-bilder visade att enstaka IONPs fästs på utsidan av de polymera NPs. Hydrofoba interaktioner mellan polymeren och oleinsyra-IONPs är möjliga. För att uppnå inkapsling av oljesyra-IONPs bör justeringar av processparametrarna för FNP övervägas i framtida forskning. Ytterligare experiment krävs för att utforska möjliga läkemedelstillsatser, frisättningsmekanismer och hypertermi hos de polymerbelagda IONP-partiklarna., Nanoparticles (NPs) offer unique possibilities for medical applications, including the controlled release of cancer drugs, the use as imaging contrast during imaging procedures or the hyperthermic treatment of cancer cells. Flash nanoprecipitation (FNP) produces NPs to combine these applications in a fast, cheap, and scalable coating process. The use of FNP with a Multi-Inlet Vortex Mixer (MIVM) is a promising method to easily coat hydrophobic oleic acid iron oxide NPs (IONPs) with various biocompatible block-copolymers. Amphiphilic block-copolymers based on hydrophilic polyethylene glycol (PEG) and hydrophobic poly(lactic acid) (PLA), poly(lactic-co-glycolic acid) (PLGA) or poly(caprolactone) (PCL) were successfully synthesized. The organic catalyst 1,8-diazabicyclo[5.4.0]undec-7-ene (DBU) was used to increase biocompatibility of the resulting polymers PEG-PLA, PEG-PL7.5KG2.5KA and PEG2K-PCL2K. The synthesis of hydroxyl terminated poly(acrylic acid) (PAA-OH) followed by the polymerization with PLGA was attempted. The amphiphilic block-copolymers were used in combination with the stabilizer polysorbate 80 (Tween80®) in FNP to form bare polymeric NPs using a MIVM as the reactor. DLS and STEM confirmed particle sizes between 50 - 100 nm. The addition of 13 ± 2 nm hydrophobic oleic acid IONPs yielded an increase in particle size as well as increase in particle stability over time. STEM images showed attachment of single IONPs to the outside of the polymeric NPs. Hydrophobic interactions between the polymer and oleic acid IONPs are possible. To achieve encapsulation of the oleic acid IONPs, adjustments to the process parameters of FNP should be considered in future research. Additional experiments are required to explore possible drug addition, release mechanisms and hyperthermia behavior of the polymer coated IONPs particles.

The development of smart wearable solutions for monitoring daily life health status is increasingly popular, with chest straps and wristbands being predominant. This study introduces a novel sensorized T-shirt design with textile electrodes connected via a knitting technique to a Movesense device. We aimed to investigate the impact of stationary and movement actions on electrocardiography (ECG) and heart rate (HR) measurements using our sensorized T-shirt. Various activities of daily living (ADLs), including sitting, standing, walking, and mopping, were evaluated by comparing our T-shirt with a commercial chest strap. Our findings demonstrate measurement equivalence across ADLs, regardless of the sensing approach. By comparing ECG and HR measurements, we gained valuable insights into the influence of physical activity on sensorized T-shirt development for monitoring. Notably, the ECG signals exhibited remarkable similarity between our sensorized T-shirt and the chest strap, with closely aligned HR distributions during both stationary and movement actions. The average mean absolute percentage error was below 3%, affirming the agreement between the two solutions. These findings underscore the robustness and accuracy of our sensorized T-shirt in monitoring ECG and HR during diverse ADLs, emphasizing the significance of considering physical activity in cardiovascular monitoring research and the development of personal health applications.

For certain materials science scenarios arising in rubber technology, one-dimensional moving boundary problems with kinetic boundary conditions are capable of unveiling the large-time behavior of the diffusants penetration front, giving a direct estimate on the service life of the material. Driven by our interest in estimating how a finite number of diffusant molecules penetrate through a dense rubber, we propose a random walk algorithm to approximate numerically both the concentration profile and the location of the sharp penetration front. The proposed scheme decouples the target evolution system in two steps: (i) the ordinary differential equation corresponding to the evaluation of the speed of the moving boundary is solved via an explicit Euler method, and (ii) the associated diffusion problem is solved by a random walk method. To verify the correctness of our random walk algorithm we compare the resulting approximations to computational results based on a suitable finite element approach with a controlled convergence rate. Our numerical results recover well penetration depth measurements of a controlled experiment designed specifically for this setting.

Modulating neural activity with electrical or chemical stimulus can be used for fundamental and applied research. Typically, neuronal stimulation is performed with intracellular and extracellular electrodes that deliver brief electrical pulses to neurons. However, alternative wireless methodologies based on functional materials may allow clinical translation of technologies to modulate neuronal function. Here, we show that the organic semiconducting oligomer 4-[2-{2,5-bis(2,3-dihydrothieno[3,4-b][1,4]dioxin-5-yl)thiophen-3-yl}ethoxy]butane-1-sulfonate (ETE-S) induces precise behaviors in the small invertebrate Hydra, which were dissected through pharmacological and electrophysiological approaches. ETE-S-induced behavioral response relies on the presence of head neurons and calcium ions and is prevented by drugs targeting ionotropic channels and muscle contraction. Moreover, ETE-S affects Hydras electrical activity enhancing the contraction burst frequency. The unexpected neuromodulatory function played by this conjugated oligomer on a simple nerve net opens intriguing research possibilities on fundamental chemical and physical phenomena behind organic bioelectronic interfaces for neuromodulation and on alternative methods that could catalyze a wide expansion of this rising technology for clinical applications., Funding Agencies|Air Force Office of Scientific Research [FA8655-22-1-7014]; European Research Council (ERC) under the European Unions Horizon 2020 research and innovation program "LINCE" [803621]; European Union (ERC-2021-STG, 4DPhytoHybrid) [101042148]; Swedish Government Strategic Research Area in Materials Science on Advanced Functional Materials at Linkoping University (Faculty Grant SFO-Mat-LiU) [2009-00971]

Manganese dioxide (MnO2) with biocompatibility has promising applications in low-voltage electrochemical actuators of implantable medical devices, which can convert electrical energy to mechanical motion. However, the unsatisfactory actuation strain restricts the generation of a larger output stress of MnO2 for practical application. Herein, a competitive reaction-driven-MnO2 (CRD-MnO2) nanorod network was fabricated on a nickel (Ni) thin-film substrate by adjusting the component molar ratios. We find that the competitive reaction between 3,4-ethylene-dioxythiophene (EDOT) polymerization and oxidation of Mn2+ controls the nucleation and growth behavior of MnO2. The variation in the electron environment, newly generated oxygen vacancies, and a higher content of structural water effectively improve the electroactivity of MnO2 and simultaneously cause more serious Jahn-Teller (JT) distortion of the crystal octahedrons. Thus, an excellent output performance simultaneously having a much higher actuating strain of 8.3% and an actuation stress of 390.1 MPa is generated during a redox reaction between Mn4+ and Mn3+ under 0-1 V. Moreover, the CRD-MnO2/Ni composite actuating films assembled on a 3D-printed resin model of a human hand with separated finger joints can perform smooth grasping and releasing actions, demonstrating a huge potential for in vitro rehabilitation exercises and implantability for people with finger dyskinesia. This work provides a strategy for actuator material fabrication by controlling a nucleation and growth process by adjusting a competitive reaction., Funding Agencies|National Natural Science Foundation of China [51971060, 51671050]; China Scholarship Council [202106080077]

Conducting polymer poly(3,4-ethylenedioxythiophene) nanowires(PEDOTNWs) were synthesized by a modified self-assembled micellar soft-templatemethod, followed by fabrication by vacuum filtration of self-supportingexfoliated WSe2-nanosheet (NS)/PEDOT-NW composite films.The results showed that as the mass fractions of WSe2 NSsincreased from 0 to 20 wt % in the composite films, the electricalconductivity of the samples decreased from & SIM;1700 to & SIM;400S cm(-1), and the Seebeck coefficient increased from12.3 to 23.1 & mu;V K-1 at 300 K. A room-temperaturepower factor of 44.5 & mu;W m(-1) K-2 was achieved at 300 K for the sample containing 5 wt % WSe2 NSs, and a power factor of 67.3 & mu;W m(-1) K-2 was obtained at 380 K. The composite film containing5 wt % WSe2 NSs was mechanically flexible, as shown byits resistance change ratio of 7.1% after bending for 500 cycles ata bending radius of 4 mm. A flexible thermoelectric (TE) power generatorcontaining four TE legs could generate an output power of 52.1 nWat a temperature difference of 28.5 K, corresponding to a power densityof & SIM;0.33 W/m(2). This work demonstrates that the fabricationof inorganic nanosheet/organic nanowire TE composites is an approachto improve the TE properties of conducting polymers., Funding Agencies|Program for Professor of Special Appointment at Shanghai Institutions of Higher Learning [TP2020068]; Shanghai Sailing Program [20YF1447300]; Natural Science Foundation of Shanghai [21ZR1462300]; Shanghai Innovation Action Plan Project [17090503600]; Knut and Alice Wallenberg Foundation through the Wallenberg Academy Fellows program [KAW 2020.0196]; Swedish Research Council [2021-03826]; Swedish Government Strategic Research Area in Materials Science on Functional Materials at Linkoping University [2009 00971]; Swedish Energy Agency [46519-1]

Wearable electronics that can be seamlessly integrated into clothing, onto skin, or inside the body, can enable a variety of novel applications within healthcare monitoring, biosensing, biomedical devices and the internet of things. Seamless integration requires matching of the mechanical properties of the electronics to clothing, skin, and tissues, i.e., the electronics need to be soft, flexible, and stretchable. One approach to achieve this is to make all or most components of a device stretchable in themselves by developing functional intrinsically stretchable composites. Such composites are typically based on a filler, which provides electronic or other functionality, and an elastomer matrix, which provides the mechanical properties of the composites. Manufacturing of intrinsically stretchable electronics is challenging and often involve time consuming and tedious fabrication procedures of low throughput, based on chemically harmful monomers and solvents. An alternative approach, printing of electronics, has experienced a boom in the past decade, recently even for stretchable applications. However, despite its appeal, stretchable printed electronic products have yet to reach the consumer market in larger numbers. Screen printing is a versatile printing method that is cost-effective, scalable, can be tailored to use harmless solvents with little waste, and can be made environmentally friendly by careful choice of materials. Furthermore, some applications of stretchable technology – such as implants and on-skin electronics – require conductors that are stable under humid, corrosive, or polluted conditions, which puts even more weight into choices of ink components. In paper I, we protected readily available conducting silver flakes through a thin coating with gold in a low-toxicity water-based process and demonstrated its use in inks for screen printed corrosion-resistant stretchable conductors. The novel silver-gold flake ink was used to fabricate a functional st

Wood is a naturally based material and plays an important role as a renewable resource when aiming for a sustainable society. Nevertheless, its inherently combustible property needs to be enhanced to comply with modern construction methods and regulations. Ammonium phosphate-based additives are often used to effectively increase the fire-retardancy (FR) of wooden products when needed. However, their water-solubility make them unsuitable for exterior use unless such properties are overcome. This PhD thesis focuses on the development of methodologies to alleviate consequences from water-leaching of wood treated with ammonium phosphate-based additives, enabling further development of new types of fire protected wood construction material for exterior uses. As such, two methodologies were explored in this thesis: 1) a composite-type fixation, involving the introduction of a hydrophobic polymer matrix for entrapping the FR additives, 2) a reactive-type fixation, which is to fix the FR additives by creating covalent bonding with the wood polymeric constituents. In order to determine the influence of composite-type fixation systems, melamine-formaldehyde (MF) prepolymer, furfuryl alcohol (FA), and kraft lignin, respectively, were studied for immobilising ammonium phosphate-based FR-additives in wood by pressure impregnating Scots pine (Pinus sylvestris L.) sapwood with a solution of the prepolymer and fire-retardant additives (FRs), followed by drying and heating steps. Through the analysis of the treated wood materials, involving scanning electron microscopy energy dispersive spectroscopy (SEM-EDX) and thermal gravimetric analysis (TGA), the formation of a stable polymeric network structure entrapping the additives inside the wood with alleviating FRs’ water-leachability was proposed. In particular, MF-resin was able to encapsulate guanyl-urea phosphate (GUP) in the lumen of the wood. Further details on the distribution and structural features of FR additives and matrices