Search

Corrosion and biofouling are wetting‐related phenomena that limit the effective use of metals in aqueous media. Nonwettable surfaces can mitigate the adverse effects of wetting by minimizing contact with water. However, current achievements in this field fall short of meeting industrial requirements due to the short lifetime of plastrons. This study proposes a method to measure the protective sustainability of plastron. Superhydrophobic (SHS) and aerophilic (APhS) surfaces are constructed on lightweight aluminum and are initially analyzed by conventional goniometry, which show comparable values. However, the plastron that develops underwater is substantially different. While SHS exhibit unevenly broken plastron, APhS show uniform, continuous plastron. As an example of the sustained protective performance of plastron, the corrosion resistance of SHS and APhS is presented. Potentiodynamic polarization, impedance spectroscopy, and long‐term immersion in seawater show a drastic enhancement in corrosion resistance, exclusively for APhS. In fact, almost no electrochemical signals are measurable, and no pitting corrosion is observed after 415 days of immersion in seawater. Conversely, SHS show no noticeable improvement and corrode faster than bare Al due to plastron loss. Since goniometric measurements do not provide information on plastron, it is essential to analyze the plastron for any non‐wettable surface utilized underwater. [ABSTRACT FROM AUTHOR]

Biofouling, caused by the attachment of micro- and macroorganisms, increases the fuel consumption of ships and compromises aquatic infrastructure, especially by microbially induced corrosion. Conventional anti-fouling strategies often rely on the release of toxic substances. Liquid-infused coatings offer an alternative strategy, which has shown promising anti-fouling performance in maritime settings. In this study, we focus on freshwater systems and investigate the performance of a set of recently developed liquid-infused coatings with low environmental impact based on sustainable or non-toxic materials and energy-efficient fabrication. We combine field studies at two freshwater bodies in Bavaria, Germany with laboratory experiments focusing on corrosion and microbial attachment under controlled conditions. Our results indicate that liquid-infused coatings with low environmental impact can show a reduction in general biofouling, mussel attachment, and corrosion rates, as well as the attachment of Thiobacillus thioparus and Pseudomonas fluorescens, organisms known to cause microbially induced corrosion. [ABSTRACT FROM AUTHOR]

Titanium dioxide (TiO2) is the material of choice for photocatalytic and electrochemical applications owing to its outstanding physicochemical properties. However, its wide bandgap and relatively low conductivity limit its practical application. Modifying TiO2 with carbon species is a promising route to overcome these intrinsic complexities. In this work, we propose a facile method to modify TiO2 nanotubes (NTs) based on the remnant organic electrolyte retained inside the nanotubes after the anodization process, that is, without removing it by immersion in ethanol. Carbon‐modified TiO2 NTs (C‐TiO2 NTs) showed enhanced H2 evolution in photocatalysis under UV illumination in aqueous solutions. When the C‐TiO2 NTs were subjected to UV light illumination, the carbon underwent modification, resulting in higher measured photocurrents in the tube layers. After UV illumination, the IPCE of the C‐TiO2 NTs was 4.4‐fold higher than that of the carbon‐free TiO2 NTs. [ABSTRACT FROM AUTHOR]

Studies on single‐atom catalysts (SACs) with individually isolated metal atoms anchored on specific supports have gained great interest in photocatalysis due to their enhanced catalytic activity and optimal atom utilization. By providing an optimized number of active sites and enhancing their intrinsic activity, SACs afford a distinctive platform for photocatalysis at the atomic level. In this study, we investigate the photocatalytic H2 generation of Pt single atoms (SAs) anchored on CdS‐sensitized single crystalline anatase TiO2 nanoflakes (ATNF) in the visible spectral range. Vertically‐aligned ATNF were synthesized on fluorine‐doped tin oxide substrates by a hydrothermal process, which were further sensitized by CdS nanoislands (NIs) using the successive ionic layer adsorption and reaction (SILAR) technique. Finally, a reactive‐deposition approach was used to successfully anchor Pt SAs on CdS‐sensitized ATNF. Under optimized conditions, the highest photocatalytic H2 evolution on Pt‐anchored single atom CdS sensitized ATNF was 17.8 μL h−1 under visible light illumination, which is 15.8, 7.5, and 6.7‐fold higher than bare CdS/FTO, PtSA/CdS/FTO, and ATNF, respectively. Overall, the density of Pt SAs plays a vital role via strong trapping of the photogenerated electrons and significantly improves the efficiency of electron‐hole separation, making PtSA/ATNF efficient solar‐driven photocatalysts. [ABSTRACT FROM AUTHOR]

Titanium dioxide (TiO2) and, in particular, its anatase polymorph, is widely studied for photocatalytic H2 production. In the present work, we examine the importance of reactive facets of anatase crystallites on the photocatalytic H2 evolution from aqueous methanol solutions. For this, we synthesized anatase TiO2 nanocrystals with a large amount of either {001} facets, that is, nanosheets, or {101} facets, that is, octahedral nanocubes, and examined their photocatalytic H2 evolution and then repeated this procedure with samples where Pt co‐catalyst is present on all facets. Octahedral nanocubes with abundant {101} facets produce >4 times more H2 than nanosheets enriched in {001} facets if the reaction is carried out under co‐catalyst‐free conditions. For samples that carry Pt co‐catalyst on both {001} and {101} facets, faceting loses entirely its significance. This demonstrates that the beneficial role of faceting, namely the introduction of {101} facets that act as electron transfer mediator is relevant only for co‐catalyst‐free TiO2 surfaces. [ABSTRACT FROM AUTHOR]

Herein we systematically investigate the influence of hydrogenation time and temperature on defects formation, structural changes, and co-catalyst free photocatalytic activity for epitaxially grown anatase thin films on strontium titanate single crystals. The photocatalytic activity trend of the anatase epi layers is similar to that of anatase powders and brookite single crystals in reported recent literature, that is, the H2 evolution rate exhibits a typical maximum upon hydrogenation under moderate annealing temperatures (500 °C). By combining surface sensitive X-ray diffraction methods and analytical high-resolution electron microscopy techniques we reveal quantitatively the oxygen loss from the epi-layer ascribed to the hydrogenation (H2 reduction) treatment. We observe specific physicochemical changes associated with the introduction of oxygen vacancies: (i) the formation of a nanoscale strained crystal surface, (ii) the agglomeration of point defects in the bulk of the anatase epi layer, and (iii) a transition towards a Ti2O3 like symmetry at the film surface, i.e. an evident oxygen deficiency at the epi layer surface in particular prominent for the most active sample as a function of the hydrogenation parameters. These extensive experimental findings allow us to propose an empirical model, which links detrimental and beneficial effects of Ti3+ centers and oxygen vacancies in the bulk and at the surface and their abundance to an optimum point defect configuration for water splitting via "grey" anatase. [ABSTRACT FROM AUTHOR]

Microscale flows of fluids are mainly guided either by solid matrices or by liquid–liquid interfaces. However, the solid matrices are plagued with persistent fouling problems, while liquid–liquid interfaces are limited to low-pressure applications. Here we report a dynamic liquid/solid/gas material containing both air and liquid pockets, which are formed by partially infiltrating a porous matrix with a functional liquid. Using detailed theoretical and experimental data, we show that the distribution of the air- and liquid-filled pores is responsive to pressure and enables the formation and instantaneous recovery of stable liquid–liquid interfaces that sustain a wide range of pressures and prevent channel contamination. This adaptive design is demonstrated for polymeric materials and extended to metal-based systems that can achieve unmatched mechanical and thermal stability. Our platform with its unique adaptive pressure and antifouling capabilities may offer potential solutions to flow control in microfluidics, medical devices, microscale synthesis, and biological assays. [ABSTRACT FROM AUTHOR]