Search

The aim of the study was to evaluate microhardness, mass changes during 1-year water immersion, water sorption/solubility, and calcium phosphate precipitation of experimental composites functionalized with 5-40 wt% of two types of bioactive glass (BG): 45S5 or a customized low-sodium fluoride-containing formulation. Vickers microhardness was evaluated after simulated aging (water storage and thermocycling), water sorption and solubility were tested according to ISO 4049, and calcium phosphate precipitation was studied by scanning electron microscopy, energy dispersive X-ray spectroscopy, and Fourier-transform infrared spectroscopy. For the composites containing BG 45S5, a significant reduction in microhardness was observed with increasing BG amount. In contrast, 5 wt% of the customized BG resulted in statistically similar microhardness to the control material, while higher BG amounts (20 and 40 wt%) resulted in a significant improvement in microhardness. Water sorption was more pronounced for composites containing BG 45S5, increasing 7-fold compared to the control material, while the corresponding increase for the customized BG was only 2-fold. Solubility increased with higher amounts of BG, with an abrupt increase at 20 and 40 wt% of BG 45S5. Calcium phosphate was precipitated by all composites with BG amounts of 10 wt% or more. The improved properties of the composites functionalized with the customized BG indicate better mechanical, chemical, and dimensional stability without compromising the potential for calcium phosphate precipitation.

Der restaurative Aufbau verlorengegangener Zahnhartsubstanz und die Wiederherstellung der ursprünglichen vertikalen Bisslage bei einem durch Zahnerosionen oder -abrasionen stark in Mitleidenschaft gezogenen Gebiss stellt den Zahnarzt immer wieder vor Probleme bei der Umsetzung der Therapie. Traditionellerweise erfolgt diese Therapie mit laborgefertigten Werkstücken, die in der Regel eine Präparation der verbliebenen Zahnsubstanz erfordern und für den Patienten hohe Kosten verursachen, sodass alternative Ver- fahren in Betracht gezogen werden sollten. Dabei gilt es hervorzuheben, dass auch minimalinvasive restaurative Arbeiten bei diesen Patienten nur dann indiziert sind, wenn der präventive Ansatz, weiteren Zahnhartsubstanzverlust zu verhindern, gleichzeitig erfolgreich ist. Der folgende Beitrag stellt die Verwendung direkter adhäsiver Kompositrestaurationen als eine Möglichkeit zur Rekonstruktion einer erosiv stark veränderten Gebisssituation anhand eines Falles dar. Zur Rekonstruktion der Okklusalflächen werden dabei Übertragungsschienen eingesetzt, die auf der Basis von individuellen Wax-up-Modellen angefertigt werden. Das beschriebene Verfahren stellt eine gut unter- suchte und erprobte Methode zur Versorgung von Zähnen mit erosionsbedingtem Zahnhartsubstanzverlust dar. Wie bei allen neuen Verfahren wird sich für den praktischen Zahnarzt eine gewisse Lernkurve ergeben, nach der hochwertige Restaurationen mit dieser Technik umgesetzt werden können.

OBJECTIVE: The aim of this research was to investigate the effect of simplified adhesive strategies (self-etch vs selective enamel etch and 10- vs 20-second adhesive application time) on the marginal integrity in primary molars. METHODS: Forty deep class-II cavities were prepared in 40 extracted primary molars. The molars were divided into 4 groups based on the applied universal adhesive strategy as follows: groups 1 and 2: selective enamel etch with 20- or 10-second application time and groups 3 and 4: self-etch with 20- or 10-second application time. All cavities were restored with a sculptable bulk-fill composite restoration. The restorations underwent a thermomechanical loading (TML, 5-50 °C, 2-minute dwelling time, ×1000; 400,000 loading cycles, 1.7 Hz, 49 N). Marginal analysis before and after TML was conducted with scanning electron microscopy and the marginal integrity of each restoration was calculated as a percentage of continuous margins. A beta regression model was adopted to statistically analyse the data with a consequent pairwise comparison. RESULTS: The mean marginal integrity (% ± SD) of the restorations for each tested adhesive strategy after TML was as follows: selective enamel etch/20 seconds = 85.4 ± 3.9, self-etch/20 seconds = 85.3 ± 5.2, self-etch/10 seconds = 80.1 ± 8.2, and selective enamel etch/10 seconds = 80.0 ± 8.5. The difference between both adhesive strategies was not statistically significant at the same application time. The difference between both application times within the same adhesive strategy was statistically significant (P ≤ .01). CONCLUSIONS: Universal adhesives applied either in selective enamel etch or in self-etch mode result in comparable marginal integrities when restoring class-II cavities in primary molars. Shortened adhesive application time (10 seconds) could lead to a reduction in the marginal integrity in comparison to the recommended application time of 20 seconds.

Self-adhesive composites promise simplified application and reliable adhesion to dental hard tissues without prior conditioning or application of an adhesive system. Their working principle is based on specific functional monomers. Although they may reach acceptable sealing capability in minimally invasive cavities, study results showed significantly reduced bond strength to enamel and dentin compared to conventional adhesive systems. Thus, the use of self-adhesive composites requires critical individual consideration.

Objectives: To prepare experimental composites with bioactive glass (BG) and investigate their release of calcium (Ca), phosphate (PO4), and fluoride (F), as well as pH changes and apatite precipitation after immersion. Methods: Experimental composites were prepared with 0, 10, or 20 wt% of either BG 45S5 or a customized low-Na F-containing BG. Three commercial ion-releasing materials were used for reference. Material specimens were immersed in lactic acid (pH = 4.0) and artificial saliva (pH = 6.4). Ion concentrations (atomic absorption spectrometry for Ca, UV-vis spectrometry for PO4, and ion-selective electrode for F) and pH were measured after 4, 8, 12, 16, 20, 24, 28, and 32 days. After immersion, composite specimens were analyzed using scanning electron microscopy (SEM) and Fourier-transform infrared (FTIR) spectroscopy. Results: Material-dependent concentrations of Ca, PO4, and F were measured in the lactic acid solution, while a decrease of Ca and PO4 concentrations was observed in artificial saliva. The uptake of ions from artificial saliva indicates their precipitation on specimen surfaces, which was supported by the results of SEM and FTIR investigations. In experimental composites functionalized with both bioactive glass types and a commercial "alkasite" material, apatite was precipitated not only in artificial saliva but also in the lactic acid solution. Conclusions: Experimental BG-containing composites and selected commercial restorative materials demonstrated the potential for releasing multiple ion types and increasing pH. Clinical significance: The observed effects can be beneficial for preventing demineralization and promoting remineralization of dental hard tissues, while apatite precipitation can additionally help in sealing marginal discontinuities. Keywords: Bioactive glass; Calcium; Fluoride; Hydroxyapatite; Phosphate; Resin composites.

Experimental dental resin composites containing copper-doped mesoporous bioactive glass nanospheres (Cu-MBGN) were developed to impart anti-bacterial properties. Increasing amounts of Cu-MBGN (0, 1, 5 and 10 wt%) were added to the BisGMA/TEGDMA resin matrix containing micro- and nano-fillers of inert glass, keeping the resin/filler ratio constant. Surface micromorphology and elemental analysis were performed to evaluate the homogeneous distribution of filler particles. The study investigated the effects of Cu-MBGN on the degree of conversion, polymerization shrinkage, porosity, ion release and anti-bacterial activity on S. mutans and A. naeslundii. Experimental materials containing Cu-MBGN showed a dose-dependent Cu release with an initial burst and a further increase after 28 days. The composite containing 10% Cu-MBGN had the best anti-bacterial effect on S. mutans, as evidenced by the lowest adherence of free-floating bacteria and biofilm formation. In contrast, the 45S5-containing materials had the highest S. mutans adherence. Ca release was highest in the bioactive control containing 15% 45S5, which correlated with the highest number of open porosities on the surface. Polymerization shrinkage was similar for all tested materials, ranging from 3.8 to 4.2%, while the degree of conversion was lower for Cu-MBGN materials. Cu-MBGN composites showed better anti-bacterial properties than composites with 45S5 BG.

This study evaluated the flexural properties of an experimental composite series functionalized with 5-40 wt% of a low-Na F-containing bioactive glass (F-series) and compared it to another experimental composite series containing the same amounts of the conventional bioactive glass 45S5 (C-series). Flexural strength and modulus were evaluated using a three-point bending test. Degree of conversion was measured using Fourier-transform infrared spectroscopy. Weibull analysis was performed to evaluate material reliability. The control material with 0 wt% of bioactive glass demonstrated flexural strength values of 105.1-126.8 MPa). In the C-series, flexural strength ranged between 17.1 and 121.5 MPa and was considerably more diminished by the increasing amounts of bioactive glass than flexural strength in the F-series (83.8-130.2 MPa). Analogously, flexural modulus in the C-series (0.56-6.66 GPa) was more reduced by the increase in bioactive glass amount than in the F-series (5.24-7.56 GPa). The ISO-recommended "minimum acceptable" flexural strength for restorative resin composites of 80 MPa was achieved for all materials in the F-series, while in the C-series, the materials with higher bioactive glass amounts (20 and 40 wt%) failed to meet the requirement of 80 MPa. The degree of conversion in the F-series was statistically similar or higher compared to that of the control composite with no bioactive glass, while the C-series showed a declining degree of conversion with increasing bioactive glass amounts. In summary, the negative effect of the addition of bioactive glass on mechanical properties was notably less pronounced for the customized bioactive glass than for the bioactive glass 45S5; additionally, mechanical properties of the composites functionalized with the customized bioactive glass were significantly less diminished by artificial aging. Hence, the customized bioactive glass investigated in the present study represents a promising candidate for functionalizi

This study investigated polymerization kinetics, linear shrinkage, and shrinkage stress development for six contemporary composite materials of different viscosities cured using radiant exitances of 1100-2850 mW/cm$^{2}$. Real-time measurements of degree of conversion, linear shrinkage, and shrinkage stress were performed over 5 min using Fourier-transform infrared spectrometry, a custom-made linometer, and a custom-made stress analyzer, respectively. For most tested variables, the factor "material" had a higher effect size than the factor "curing protocol". Maximum polymerization rate and maximum shrinkage stress rate were the most affected by changes in curing conditions. In contrast, no significant effects of curing conditions were identified within each material for shrinkage stress values measured at the end of the 5 min observation period. Linear shrinkage and shrinkage stress values measured after 5 min were closely correlated (R = 0.905-0.982). The analysis of polymerization kinetics suggested that the two composites specifically designed for rapid light-curing responded to higher radiant exitances differently than other composites. Polymerization kinetics and shrinkage stress behavior of contemporary restorative composite materials of different viscosities were overall more affected by material type than differences in curing conditions. Subtle differences in polymerization kinetics behavior shown by the two composites specifically designed for rapid high-intensity light-curing did not translate into significant differences in the development of polymerization shrinkage stress.

Over the last years, bioactive glass particles have been successfully incorporated in dental restorative materials. Remineralizing effects on dental hard tissue and antibacterial properties are promising properties of these customized composites. A few materials doped with bioactive fillers are already available on the dental market. Nevertheless, further research is required to fine-tune bioactive composites for biomimetic restorative approaches. Sind mit bioaktiven Füllpartikeln modifizierte Komposite zukunfts weisende Materialien? Dieser Artikel informiert über ihre wichtigsten Eigenschaften

The objective was to evaluate new commercially available ion-releasing restorative materials and compare them to established anti-cariogenic materials. Four materials were tested: alkasite Cention (Ivoclar Vivadent) in self-cure or light-cure mode, giomer Beautifil II (Shofu), conventional glass-ionomer Fuji IX (GC), and resin composite Tetric EvoCeram (Ivoclar Vivadent) as a control. Flexural strength, flexural modulus, and Weibull modulus were measured one day, three months, and after three months with accelerated aging in ethanol. Water sorption and solubility were evaluated for up to one year. Degree of conversion was measured during 120 min for self-cured and light-cured Cention. In this study, Beautifil II was the ion-releasing material with the highest flexural strength and modulus and with the best resistance to aging. Alkasite Cention showed superior mechanical properties to Fuji IX. Weibull analysis showed that the glass-ionomer had the least reliable distribution of mechanical properties with the highest water sorption. The solubility of self-cured alkasite exceeded the permissible values according to ISO 4049. Degree of conversion of light-cured Cention was higher than in self-cure mode. The use of alkasite Cention is recommended only in the light-cure mode.

We embedded copper-doped mesoporous bioactive glass nanospheres (Cu-MBGN) with antibacterial and ion-releasing properties into experimental dental composites and investigated the effect of Cu-MBGN on the polymerisation properties. We prepared seven composites with a BisGMA/TEGDMA (60/40) matrix and 65 wt.% total filler content, added Cu-MBGN or a combination of Cu-MBGN and silanised silica to the silanised barium glass base, and examined nine parameters: light transmittance, degree of conversion (DC), maximum polymerisation rate (Rmax), time to reach Rmax, linear shrinkage, shrinkage stress (PSS), maximum PSS rate, time to reach maximum PSS rate, and depth of cure. Cu-MBGN without silica accelerated polymerisation, reduced light transmission, and had the highest DC (58.8 ± 0.9%) and Rmax (9.8 ± 0.2%/s), but lower shrinkage (3 ± 0.05%) and similar PSS (0.89 ± 0.07 MPa) versus the inert reference (0.83 ± 0.13 MPa). Combined Cu-MBGN and silica slowed the Rmax and achieved a similar DC but resulted in higher shrinkage. However, using a combined 5 wt.% Cu-MBGN and silica, the PSS resembled that of the inert reference. The synergistic action of 5 wt.% Cu-MBGN and silanised silica in combination with silanised barium glass resulted in a material with the highest likelihood for dental applications in future. Keywords: copper; depth of cure; light transmission; linear shrinkage; mesoporous; polymerisation; polymerisation kinetics; polymerisation shrinkage stress.

The aim of the study was to examine the applicability of bioactive and antibacterial nanoparticles to an experimental adhesive. The adhesive (60 wt% BisGMA, 15 wt% TEGDMA, 25 wt% HEMA) was mixed with combinations of 5 wt% methacryl-functionalized polyhedral oligomeric silsesquioxane (MA-POSS) and one kind of bioactive/antibacterial nanoparticles: 1 wt% core-shell silica-silver nanoparticle (SiO2@Ag), 1 wt% bioactive glass with bismuth (BAG-Bi) or 1 wt% calcium phosphate (CAP). Pure adhesive served as control. The physicochemical (degree of conversion (DC), linear shrinkage (LS), shear and complex viscosity, water sorption (WS), sol fraction (SF)), biological (antimicrobial effect) and bioactive (mineral precipitation) properties were investigated. DC and LS remained unchanged. The combination of BAG-Bi/MA-POSS resulted in a significantly increased WS and SF compared to control. In addition, the combination of CAP/MA-POSS slightly increased the shear viscosity of the adhesive. The addition of the nanoparticles did not influence the antimicrobial effects compared to the pure adhesive. Improved mineral inducing capacity could be detected in all nanoparticle combinations. The combination of bioactive and/or antibacterial nanoparticles showed improved mineral inducing capacity, but no antibacterial properties. The material properties were not or only slightly affected. Keywords: POSS; SiO2@Ag; antimicrobial nanoparticles; bioactive glass; bioactive nanoparticles; calcium phosphate; dental adhesive.

Bulk-fill composites enable timesaving and less technical-sensitive application of restorations. This study investigated and compared the marginal integrity of classical and bulk-fill composite restorations in primary and permanent molars before and after thermo-mechanical loading (TML). Two Class II cavities were prepared in each of 20 primary and 20 permanent molars. The molars were randomised in four groups for each molar type. Groups 1 and 5 were restored with a high-viscous bulk-fill composite (Tetric PowerFill), groups 2 and 6 were restored with a flowable bulk-fill composite (Tetric PowerFlow), groups 3 and 7 were restored with a high-viscous classical composite (Tetric Prime), and groups 4 and 8 were restored with a flowable classical composite (Tetric EvoFlow). In permanent molars, the flowable composites were covered with a 2-mm layer of high-viscous composite (groups 6 and 8). The restorations were subjected to TML in a custom-made chewing machine (5-50 °C, 2 min dwelling time, × 1000; 400 ,000 loading cycles, 1.7 Hz, 49 N), and quantitative marginal analysis was conducted using scanning electron microscopy. Marginal integrity of each restoration was calculated as a percentage of continuous margins before and after TML. The tested high-viscous bulk-fill restoration showed similarly high marginal integrity in primary and permanent molars as the classical restoration. The tested flowable bulk-fill restoration showed the lowest marginal integrity compared to all other restorations after TML. In contrast to flowable bulk-fill restorations, high-viscous bulk-fill restorations show similar marginal integrity as classical hybrid composite restorations after TML, in both primary and permanent molars.