Search

Integrating power electronics with batteries can offer many advantages, including load sharing and balancing with parallel connectivity. However, parallel batteries with differing voltages and power profiles can cause large circulating currents and uncontrolled energy transfers, risking system instability. To overcome these challenges, we propose a novel modular reconfigurable topology for AC batteries with coupled inductors between adjacent submodules. This approach dynamically manages energy distribution between energy and power modules. Under normal conditions, energy modules operate in series or parallel configurations to deliver stable voltage and current, ensuring efficient power delivery. During heavy loads, such as during electric-vehicle acceleration, power modules seamlessly meet additional power demands beyond the energy modules' capacity. The use of mutual inductors reduces inductance along the load path for faster response times while providing sufficient inductance to regulate circulating currents and enable efficient energy transfer among modules. The system's AC load further complicates control, necessitating a simple yet effective feedforward-feedback control strategy to maintain satisfactory performance., Comment: 15 pages, 36 figures

Recently, energy encryption for wireless power transfer has been developed for energy safety, which is important in public places to suppress unauthorized energy extraction. Most techniques vary the frequency so that unauthorized receivers cannot extract energy because of non-resonance. However, this strategy is unreliable. To stimulate the progress of energy encryption technology and point out security holes, this paper proposes a decryption method for the fundamental principle of encrypted frequency-varying wireless power transfer. The paper uses an auxiliary coil to detect the frequency and a switched-capacitor array to adaptively compensate the receiver for a wide frequency range. The switched-capacitor array contains two capacitors and one semi-conductor switch. One capacitor compensates the receiver all the time while the other's active time during one wireless power transfer cycle is regulated by the switch. Thus, the proposed hacking receiver controls the equivalent capacitance of the compensation and steals energy. Finally, a detailed simulation model and experimental results prove the effectiveness of the attack on frequency-hopping energy encryption. Although any nonnegligible energy extracted would be problematic, we achieved to steal 78% to 84% of the energy an authorized receiver could get. When the frequency changes, the interceptor is coarsely tuned very quickly, which can hack fast frequency-varying encrypted system., Comment: 10 pages, 17 figures

Modular battery integrated converters or so called dynamically reconfigurable battery packs are expanding into emerging applications, including electromobility and grid storage. Although they offer many degrees of freedom, the state of the art focuses on single output systems and mostly neglects potential of such systems in generating multiple controlled outputs. This paper investigates the use of the extra degrees of freedom that a reconfigurable battery offers to generate multiple outputs for the adjustable supply of various independent loads. The technology offers the potential for functional integration, exploiting already existing transistors, and for a reduction of separate dedicated power conversion stages. Interleaved output ports, where some modules are shared among different outputs, can further reduce the necessary power electronics and cost. However, using conventional modulation techniques in particular phase-shifted carrier modulation can be challenging with shared modules among multiple ports, and different control objectives can adversely impact the overall performance. Therefore, this paper proposes a strategy to decouple the control of multiple ports to enable further simplification of required power electronics. The proposed system does not require any additional active switches for the isolated port and can operate with a wide range of output voltages. Simulation and experiments verify the developed analysis.

This paper proposes a drive train topology with a dynamically reconfigurable dc battery, which breaks hard-wired batteries into smaller subunits. It can rapidly control the output voltage and even contribute to voltage shaping of the inverter. Based upon the rapid development of low-voltage transistors and modular circuit topologies in the recent years, the proposed technology uses recent 48 V power electronics to achieve higher-voltage output and reduce losses in electric vehicle (EV) drive trains. The fast switching capability and low loss of low-voltage field effect transistors (FET) allow sharing the modulation with the main drive inverter. As such, the slower insulated-gate bipolar transistors (IGBT) of the inverter can operate at ideal duty cycle and aggressively reduced switching, while the adaptive dc battery provides an adjustable voltage and all common-mode contributions at the dc link with lower loss. Up to 2/3 of the switching of the main inverter is avoided. At high drive speeds and thus large modulation indices, the proposed converter halves the total loss compared to using the inverter alone; at lower speeds and thus smaller modulation indices, the advantage is even more prominent because of the dynamically lowered dc-link voltage. Furthermore, it can substantially reduce the distortion, particularly at lower modulation indices, e.g., down to 1/2 compared to conventional space-vector modulation and even 1/3 for discontinuous pulse-width modulation with hard-wired battery. Other benefits include alleviated insulation stress for motor windings, active battery balancing, and eliminating the vulnerability of large hard-wired battery packs to weak cells. We demonstrate the proposed motor drive on a 3-kW setup with eight battery modules., Comment: 11 pages, 9 figures

Dynamically reconfigurable batteries merge battery management with output formation in ac and dc batteries, increasing the available charge, power, and life time. However, the combined ripple generated by the load and the internal reconfiguration can degrade the battery. This paper introduces that the frequency range of the ripple matters for degradation and loss. It presents a novel control method that reduces the low-frequency ripple of dynamically reconfigurable battery technology to reduce cell ageing and loss. It furthermore shifts the residual ripple to higher frequencies where the lower impedance reduces heating and the dielectric capacitance of electrodes and electrolyte shunt the current around the electrochemical reactions., Comment: 8 pages, 8 figures

Whereas in typical standardized tests batteries are almost exclusively loaded with constant current or relatively slowly changing cycles, real applications involve rapid load ripple, which do not contribute to the net energy. The trend to reduced filter capacitors and even dynamically reconfigurable batteries further increases the ripple. The influence of rippled load on lithium batteries is therefore receiving increased attention. According to recent studies, accelerated ageing strongly depends on the frequency of the ripple. We use electrochemical models to derive a highly simplified regression model that catches the asymptotic behavior and allows parameter identification and calibration to specific cells. The model allows quantitative monitoring of the additional ageing due to ripple current in battery management systems. Furthermore it enables active control of the ageing potential by influencing the frequency content in modern battery systems, such as reconfigurable batteries., Comment: 7 pages

Recent research on multilevel inverters shows exciting properties, including the potential to generate multiple output voltages and integrated voltage boosting. However, most presented inverter topologies have a restricted number of output voltage levels and limited output voltage boosting ratio. In addition, balancing the voltage of capacitors in multilevel converters is very important and should be considered in the topology or control method. This paper describes a generalized switched-capacitor circuit topology for multilevel dc-to-ac inverters that can be developed for the desired output voltage levels. Also, the maximum ac output voltage can vary from values much lower than the dc input voltage to several times of it depending on the design requirement. High-voltage dc input and ac output could be handled using low-voltage capacitors, which substantially decreases overall cost and volume. The proposed topology further allows for easy expansion through stackable circuits for multiple load phases. It has an inherent capacity for balancing the voltage of capacitors. To validate the feasibility and practicality of this concept, we provide circuit descriptions, control strategies, design recommendations, and pertinent simulation findings for the suggested inverter topology.

Inrush current problems of the industrial transformers are occasionally more serious than the utility transformers. A new Solid-State Inrush Current Limiter (SSICL) is proposed for medium voltage power transformers. The SSICL consists of three similar sets. Each set includes a bidirectional semiconductor switch and an inrush current limiter resistor. Using a control strategy based on Kalman filtering, transformer inrush current is suppressed during magnetization process. In fact, built up profile of the inrush current is dictated in accordance with the estimated current by a slow dynamic Kalman filter. A single-phase prototype SSICL is developed and tested. The proposed control scheme is simulated in MATLAB-SIMULINK. By using Real Time (RT) toolbox of the MATLAB software and a PCI_1711U, interrelationship between the SSICL and its controlling system is realized. Some experiments are carried out to evaluate the performance of the SSICL. The results show that the proposed SSICL can considerably suppress inrush current of the transformer