Search

Understanding the underlying principles of contact electrification is critical for more efficient triboelectric nanogenerator (TENG) development. Herein, we use ReaxFF molecular dynamics simulations in conjunction with a charge equilibration method to investigate the contact electrification mechanism in polyisoprene (PI), a natural rubber polymer, when it comes into contact with copper (Cu) and polytetrafluoroethylene (PTFE). The simulations reveal that the charge transfer directions in the PI/Cu and PI/PTFE contact models are opposite, and the amount of charge transfer in the former is substantially less than that in the latter, which are consistent with our TENG measurements. Contact electrification is revealed to be a spontaneous process that occurs to lower electrostatic energy, and the electrostatic energy released during contact electrification of PI/PTFE is greater than that of PI/Cu, which can be correlated with the relative strength of triboelectric charging observed for the two systems. A compression simulation of the PI/Cu contact model reveals that the quantity of charge transfer grows exponentially as compressive strain increases. Despite increasing the total energy of the system due to densification and distortion of the polymer structure, the applied deformation results in an energetically more stable electrostatic arrangement. We also find that the incorporation of a carbonaceous material into a polyisoprene matrix causes a faster increase in the amount of charge transfer with compressive strain, which is governed by a steeper electrostatic energy profile. This study provides an alternative perspective on the contact electrification mechanism, which could be beneficial for the development of energy harvesting devices. [ABSTRACT FROM AUTHOR]

As we known waves contain important information, however, to realizing high-precision quantification for ocean exploitation and utilization is challenging. In this paper, we proposed a neural network for wave height detection by training the voltage waveform of a triboelectric nanogenerator (TENG). First, we analyzed the voltage signal obtained using a TENG. Second, we proposed a lightweight artificial neural network model that achieves a minimal monitoring error of 0.049% at low amplitudes and yields better monitoring results than the linear model. The findings presented in this paper enable the measurement of water surface waves and eliminate the influence of external factors on sensor performance. Wave parameters can be obtained using neural networks, and this work provides a new strategy for computational and intelligent applications by using wave data. [ABSTRACT FROM AUTHOR]

Humans recognize and manipulate objects relying on the multidimensional force features captured by the tactile sense of skin during the manipulation. Since the current sensors integrated in robots cannot support the robots to sense the multiple interaction states between manipulator and objects, achieving human‐like perception and analytical capabilities remains a major challenge for service robots. Prompted by the tactile perception involved in robots performing complex tasks, a multimodal tactile sensory system is presented to provide in situ simultaneous sensing for robots when approaching, touching, and manipulating objects. The system comprises a capacitive sensor owning the high sensitivity of 1.11E‐2 pF mm−1, a triboelectricity nanogenerator with the fast response speed of 30 ms, and a pressure sensor array capable of 3D force detection. By Combining transfer learning models, which fuses multimodal tactile information to achieve high‐precision (up to 95%) recognition of the multi‐featured targets such as random hardness and texture information under random sampling conditions, including random grasp force and velocity. This sensory system is expected to enhance the intelligent recognition and behavior‐planning capabilities of autonomous robots when performing complex tasks in undefined surrounding environments. [ABSTRACT FROM AUTHOR]

The surface charge decay is observed at high temperatures due to thermionic emission, which, however, may not be the only mechanism contributing to the surface charge variation. Here, a triboelectric charge promotion strategy due to the heat‐excitation effect of hot electrons near the fermi level is demonstrated, while the final charge is determined by the balance between thermionic emission and the heat‐excitation effect. It is demonstrated that metals with lower work function exhibit a better heat excitation capability, and polymers with lower fluorine content in molecule chains further boost the charge output, where metal/Kapton pairs demonstrated a charge promotion of over 2 times at the temperature of 383 K with good durability during 90 min measurement. The heat‐excitation effect and charge durability in sliding freestanding‐triboelectric‐layer (SFT) mode triboelectric nanogenerator (TENG) is demonstrated as well, where the energy is promoted by over 3 times and the capacitor charging speed is doubled as well, with an energy promotion from 109.34 to 373 µJ per cycle to successfully trigger a discharger. This work suggests a promising future of the heat‐excitation effect as a new charge promotion strategy for TENG toward different applications in high‐temperature environments. [ABSTRACT FROM AUTHOR]

Triboelectric nanogenerator (TENG) technology based on the coupling of triboelectric effect and electrostatic induction has shown great potential in the energy‐integration field. In recent years, the emerging of textile triboelectric nanogenerators (t‐TENGs) has enabled the rapid development of wearable energy‐integration technologies. The efficient mechanical energy harvesting and self‐powered sensing capabilities of TENGs and the advantages of textiles can be combined to create t‐TENGs for the construction of smart fabrics. Herein, a comprehensive review of t‐TENGs is presented. This review begins from the working mechanism of conventional TENGs, after which the construction of triboelectric layers with fibers, yarns, and fabrics is discussed. Then, the different working modes of t‐TENGs derived from TENGs, the critical features of t‐TENGs and power management strategies are discussed. Finally, this review ends with a description of the recent progress in typical wearable applications based on t‐TENGs. The light weight, low cost, flexibility, stretchability, washability, diverse material options, and excellent electrical performance of t‐TENGs will make this technology a great choice for smart energy‐integrated wearable devices in the future. [ABSTRACT FROM AUTHOR]

Mineral dust from the Sahara desert can travel long distances at high altitudes, perturbing the energy budget of the atmosphere. Charging of dust has been observed to occur near the surface through triboelectric charging during dust lofting, potentially affecting particle coagulation, fall speeds, and the lofting process itself. Apart from near-surface studies, measurements at elevated dust layers, where charge may play a role in particle long-range transport, are rare. This study presents new observations from an uncrewed aircraft system (UAS) of type MASC-3, through an elevated Saharan dust layer over Cyprus on 6 April 2022. The dust layer ranged from 1500 to 2500 meters above sea level (a.s.l), with maximum particle number concentrations (PNC) of 80–100 cm − 3 , primarily consisting of particles up to 2.5 µm in size. Measurements showed elevated charge within the dust layer, with magnitude proportional to PNC. It was concluded that there was a small influence of aircraft charge on the measurements, which was handled by developing a PNC-based correction factor. Corrected charge within the dust layer ranged from 0.2 to 3 pC m − 3 , with most of the charge at the upper and lower dust layer boundaries. The magnitude and location of the charge was consistent with predictions of ion-particle attachment. This suggests that most of the measured charge did not originate from the lofting process, but dust particles were charged on site through ion-particle attachment processes. [ABSTRACT FROM AUTHOR]

Droplet-based electricity generators (DEGs) leveraging triboelectric effects are simple and high-performance devices for harvesting energy from ubiquitous water droplets. Instantaneous power plays a vital role in wide applications of DEGs. However, the governing law of the maximum instantaneous power and matching resistance is lacking and their determination suffers from heavy repetitive experiments, hindering the development of DEGs. Herein, we propose a quick evaluation method for the internal droplet impedance, instantaneous peak power, maximum instantaneous power and matching resistance which exhibits broad universality and excellent accuracy. Moreover, effects of diverse factors pertaining to droplets and devices are fully investigated, highlighting that the maximum instantaneous power and matching resistance can be effectively regulated across multiple orders of magnitudes by controlling the salt concentration. Our findings shed insights into the understanding, evaluation, and regulation of instantaneous power for DEGs, and shall promote the renovation of the DEG technology. [ABSTRACT FROM AUTHOR]

Triboelectric nanogenerators (TENGs) provide promising power supply solutions by transforming mechanical energy into electrical energy. However, enhancing electrical performance of TENGs is essential for their widespread practical applications and commercialization. In this study, we fabricated TENGs in vertical contact‐separation mode using a tribopositive material—polyvinyl alcohol (PVA) slime—which is biocompatible, flexible, and wearable, decorated with graphene nanoplatelets (GnPs), and paired with tribonegative silicone. We analyzed the correlation between the electrical performance of the TENGs and the inherent triboelectric properties of the constituent material, including the evaluation of surface roughness, the measurement of the contact potential difference (CPD), and the material's dielectric constant. The incorporation of GnPs increased the dielectric constant of the composite material and its electron‐donating tendency, thus, increasing the contact potential difference. The GnPs concentration of 1 wt% was identified as the optimal value, resulting in a 42% increase in power density. The 1 wt% GnPs@PVA&Silicone TENG exhibited an open‐circuit voltage of 718 V and a peak power density of 15.3 W/m2. This study sheds light on enhancing the energy harvesting efficiency of TENGs through the utilization of biocompatible tribopositive and tribonegative materials. [ABSTRACT FROM AUTHOR]

Extracting water from air offers a promising route to address the global challenge of water scarcity. However, bionic engineering surfaces for water harvesting often struggle with efficiently coordinating droplet nucleation and desorption. The recently emerging triboelectric effect at the liquid–solid interface offers a novel approach for developing bionic fog harvesting surfaces. In this study, inspired by Namib Desert beetles and lotus leaves, a biomimetic superhydrophobic surface with nanoscale hydrophilic domains is prepared via interfacial self‐assembly, exhibiting heterogeneous wettability for effective water harvesting. The essence of interfacial self‐assembly lies in the synergy of non‐covalent interaction forces, driving the self‐assembly of nanoparticles into surface micro‐nano hierarchical structures, thereby regulating wettability and increasing potential nucleation sites. Additionally, the triboelectric effect can directly utilize the triboelectric charges to facilitate droplet migration. The triboelectric effect can be generated by flexible mechanical input induced by walking, which enhances interfacial mass transfer, thereby rapidly improving droplet removal and achieving a 39.02% increase in water harvesting efficiency. This study has opened up a new breakthrough for the design of portable and efficient water harvesting systems. [ABSTRACT FROM AUTHOR]

Woody biomass is an abundant renewable resource. In this study, aerogels for versatile triboelectric devices are fabricated from poplar biomass via a dissolution‐and‐regeneration method with concentrated lithium bromide solution as the solvent. To improve the aerogels' structural homogeneity, two treatments—ball‐milling the raw poplar woody biomass before its dissolution, and, separately, ultrasonication following its dissolution—were applied. These treatments altered the porous structures and mechanical properties of the resulting aerogels, leading to a marked increase in their triboelectric performance. Removing the majority of the lignin from the aerogels was also explored, and resulted in triboelectric output ≈5 times greater than that of pristine woody biomass aerogel (i.e., without ball milling, ultrasonication, or lignin reduction). The underlying mechanisms of such increases were found to be both chemical and physical. Next, triboelectric devices were fabricated using the optimal (i.e., low‐lignin) aerogel for energy harvesting and biomechanical monitoring. These devices were able to: 1) respond sensitively to force, likely due to the aerogel's porous structures; 2) capture mechanical energy, charge capacitors, and power small portable electronics; and 3) monitor biomechanical movements including respiration, joint motions, and gait‐pattern changes. [ABSTRACT FROM AUTHOR]

Electrostatic fields are crucial for achieving the highly efficient filtration of airborne pollutants. However, the dissipation of static charges over time, especially under humid conditions, limits their practical application. In this study, we present a self-charging air filter (SAF) powered by a triboelectric nanogenerator (TENG). This SAF is integrated into a commercial mask, termed SAFM, which can effectively capture and degrade airborne pollutants without requiring an external power source. By leveraging the triboelectric effect during breathing, the TENG within the SAFM continuously replenishes static charges, maintaining the triboelectric field. The system employs a cellulose aerogel/Ti3C2Tx composite as the electron donor and an esterified cellulose-based electrospun nanofiber as the electron acceptor. Remarkably, the triboelectric field significantly enhances filtration performance, with the SAF achieving up to 95.7% filtration efficiency for particulate matter as small as 0.3 μm. This work underscores the potential of TENG-powered triboelectric fields in the development of multifunctional, human-machine interactive facemasks. [ABSTRACT FROM AUTHOR]

Nearly four decades have passed since IBM scientists pioneered atomic force microscopy (AFM) by merging the principles of a scanning tunneling microscope with the features of a stylus profilometer. Today, electrical AFM modes are an indispensable asset within the semiconductor and nanotechnology industries, enabling the characterization and manipulation of electrical properties at the nanoscale. However, electrical AFM measurements suffer from reproducibility issues caused, for example, by surface contaminations, Joule heating, and hard‐to‐minimize tip drift and tilt. Using as experimental system nanoscale Schottky diodes assembled on oxide‐free silicon crystals of precisely defined surface chemistry, it is revealed that voltage‐dependent adhesion forces lead to significant rotation of the AFM platinum tip. The electrostatics‐driven tip rotation causes a strain gradient on the silicon surface, which induces a flexoelectric reverse bias term. This directional flexoelectric internal‐bias term adds to the external (instrumental) bias, causing both an increased diode leakage as well as a shift of the diode knee voltage to larger forward biases. These findings will aid the design and characterization of silicon‐based devices, especially those that are deliberately operated under large strain or shear, such as in emerging energy harvesting technologies including Schottky‐based triboelectric nanogenerators (TENGs). [ABSTRACT FROM AUTHOR]

Humidity sensors using triboelectric nanogenerators (TENGs) technology can provide continuous operation without the need for additional batteries. These sensors provide sustainable and self-powered humidity monitoring solutions, that can be utilized in various agriculture platforms and food processing industries. In this work, a sol-gel method is utilized to process the bismuth ferrite (abbreviated as BFO) materials and a simple mould pressing method to obtain freestanding Ethylene-vinyl acetate (abbreviated EVA)-BFO composites. These composites were characterized to shed light upon structural and microstructural properties. The single electrode mode operating TENG was fabricated having 2 cm × 2 cm active area at various wt.% of BFO onto EVA-based composites to compare the electrical response. The 5 wt.% BFO-EVA-based composites/FEP-based TENG generates a voltage and current of 45 V and 800 nA. Further, the TENG device was tested for long-term stability for 400 s, and charging of various capacitors having capacitance values such as 0.1 μF, 1 μF, 4.7 μF, and 10 μF along with 3 times charging/discharging cycles of 0.1 μF capacitor have been demonstrated. The humidity sensing mechanism elucidated which follows the conduction process based on the Grotthuss proton hopping mechanism. The TENG demonstrates a sensitivity of 0.53 V/RH% over the relative humidity range from 25 % to 85 %. The powering of the wristwatch confirms that fabricated TENG can be a reliable power source for future low-power electronics. [ABSTRACT FROM AUTHOR]

Programmed droplet transport which is typically directed by surface energy gradients or external fields, is crucial in domains ranging from chemical reaction modulation to self‐powered intelligent sensing. However, droplet motion control remains constrained by path reconfiguration, requirements on chemical surface modification, and platform complexity. Here, a more universal plug‐and‐play droplet manipulation paradigm based on liquid‐solid contact electrification and triboelectricwetting on common dielectric surfaces is reported. By regulating the electrical double layer via asymmetric ion dynamics, the triboelectric charge polarity of droplets can be adjusted, enabling in situ manipulation without path reconfiguration dictated by the conventional droplet motion output. Droplets achieved an ultrahigh velocity of 450 mm s−1 on general surfaces, significantly exceeding the speeds observed in droplets subjected to constant electrostatic fields with chemical modifications. This flexible and modular functionally decoupled manipulation strategy offers an environmentally friendly, cost‐effective, and versatile paradigm, facilitating applications in chemical analysis and smart sensing. [ABSTRACT FROM AUTHOR]

Triboelectric nanogenerators (TENGs) can collect and convert random mechanical energy into electric energy, with remarkable advantages including broadly available materials, straightforward preparation, and multiple applications. Over the years, researchers have made substantial advancements in the theoretical and practical aspects of TENG. Nevertheless, the pivotal challenge in realizing full applications of TENG lies in ensuring that the generated output meets the specific application requirements. Consequently, substantial research is dedicated to exploring methods and mechanisms for enhancing the output performance of TENG devices. This review aims to comprehensively examine the influencing factors and corresponding improvement strategies of the output performance based on the contact electrification mechanism and operational principles that underlie TENG technology. This review primarily delves into five key areas of improvement: materials selection, surface modification, component adjustments, structural optimization, and electrode enhancements. These aspects are crucial in tailoring TENG devices to meet the desired performance metrics for various applications. [ABSTRACT FROM AUTHOR]

In this study, a mechanically flexible structure, a cuboctahedral metal‐organic polyhedra (MOP) Cu24[5‐(octyloxy) isophthalic acid]24 Cu (II) paddlewheel clusters coordinated with (5‐(octyloxy) isophthalate), resulting in significantly enhanced hydrolytic stability are prepared. It should be noted that CuMOP‐1 exhibits evenly and symmetrically distributed non‐polar long alkyl chains and polar hydroxy groups, facilitating self‐assembly into higher‐order structures reminiscent of amphiphiles. Furthermore, the resultant CuMOP‐1 undergoes a phase change at 150–160 °C as confirmed temperature‐dependent Raman spectroscopy (RS), thermogravimetric analysis and Differential Scanning Calorimetry (TGA‐DSC). The possible use of Cu‐MOP‐1 for capturing mechanical energy is demonstrated by creating a flexible hybrid piezoelectric‐triboelectric nanogenerator (HP‐TENG). The resultant CuMOP‐1@ Polyvinylidene fluoride(PVDF) membrane‐based HP‐TENG demonstrates enhanced triboelectric output voltage of 547.5 V, current density of 15.16 µAcm−2, and power density of 2.8 mWcm−2 due to its increased surface charge density and a substantial rise in the dielectric constant. Furthermore, the amphiphiles and phase change in CuMOP‐1 lead to ∽73% increase in voltage and 60% in current density of HP‐TENG in high‐temperature (140 °C) environments. HP‐TENG also exhibits exceptional temperature‐ and pressure‐sensing abilities, with sensitivities of 1.81 V°C−1 and 7.12 V°kPa−1, respectively, showcasing its feasibility over a wide range of temperatures and pressures. [ABSTRACT FROM AUTHOR]

Triboelectric nanogenerators have recently gained enormous attention as a low‐cost method for converting abundant mechanical energy into electricity. Here, a continuous direct current (DC) output from a triboelectric nanogenerator (TENG) is achieved using two dimensional (2D)‐WS2/Si heterojunctions, without any need for a rectifier circuit element. At the interface of the p–Si and n–WS2 heterojunction, the "Tribo‐photovoltaic effect" is observed, responsible for the generation of direct tribo‐outputs. The demonstrated multifunctional DC‐TENG with remarkable performance can concurrently convert mechanical and photonic energy into an electrical one. In comparison to dark conditions, the device's output performance is enhanced under UV illumination (365 nm, 1022 µW cm−2), and the exhibited output voltage (10.75 V) and current (466 nA) are higher by a factor of 3.9 and 2.4, with excellent power harvesting ability and outstanding robustness. This versatile DC‐TENG is demonstrated to be an attractive platform for high‐performance vision sensors and UV detection, which has significant implications for the rapid development of self‐powered portable sensing and IoT devices based on Si CMOS technology. [ABSTRACT FROM AUTHOR]

This study presents a novel transparent, sensitive electronic skin (S-TENG) using a frictional nanogenerator for energy harvesting and physiological motion monitoring. Featuring thermally treated PVDF fiber membranes and silver nanowire electrodes, the e-skin boasts 80% transparency, high sensitivity (detecting 0.13 g touch), stability, and breathability. It generates 301 V and 2.7 µA under 8N force, achieving 306 mW/m2 power density. S-TENG holds promise for self-powered wearables and health training applications, representing a significant step in e-skin innovation. [Display omitted] Against the backdrop of advancements in modern multifunctional wearable electronics, there is a growing demand for simple, sustainable, and portable electronic skin (e-skin), posing significant challenges. This study aims to delineate the development of a straightforward, transparent, highly sensitive, and high power-density electronic skin based on a triboelectric nanogenerator(S-TENG), designed for harvesting human body energy and real-time monitoring of the physiological motion status. Our e-skin incorporates thermally treated polyvinylidene fluoride (PVDF) fiber membranes as the contact layer and a film of silver nanowires as the conductive electrodes. The resulting contact-separation type e-skin exhibits an impressive transparency of 80 %, along with a nice sensitivity value, capable of detecting a light touch from a 0.13 g sponge and demonstrating good working stability and breathability. Leveraging the triboelectric effect, our e-skin generates an open-circuit voltage of 301 V and a short-circuit current of 2.7 μA under an extrinsic force of 8 N over an interaction area of 4 × 4 cm2, achieving a power density up to 306 mW/m2. With its signal processing circuitry, the integrated S-TENG showcases nice energy harvesting and signal transmission capabilities. Accordingly, we contend that S-TENG has potential applications in energy capture and real-time human motion state monitoring. This research is anticipated to blaze a novel and practical trail for self-powered wearable devices and personalized health rehabilitation training regimens. [ABSTRACT FROM AUTHOR]

The effect of rotary triboelectric separation parameters on decarburization of fly ash was systematically studied to prove that the technology was an effective means to purify fly ash. The results showed that obvious mismatch of carbon particles occurs when separation voltage was greater than 25 kV, while mismatch of other mineral particles was generated when separation voltage was greater than 30kV; The decarburization effect of fly ash could be significantly reduced due to the decrease of particle surface charge density when the feed frequency was greater than 20 hz. The feed was also affected by the speed and direction of the particle feed, the closer to the middle of the feed port, the higher the probability of the particle being effectively separated; when rotation speed of the friction wheel exceeded 4000 r/min, the particle mismatch in the separation chamber becomes more and more obvious. In addition, the speed of the friction wheel also affected flow field in separation chamber, which may have an adverse effect on separation effect; Co-flow velocity affected retention time of particles in the separation chamber. 6 m/s is the best co-flow velocity for fly ash decarburization. In this case, the flow field generated by the co-flow is uniform to ensure stable transport of particles. [ABSTRACT FROM AUTHOR]

Photodynamic therapy (PDT) as a clinical method relies on appropriate light delivery to activate photosensitizers, usually necessitates the utilization of cumbersome surgical instruments and high irradiation intensity, along with the requirement for hospitalization. To extend the applicability of PDT beyond hospital for better patient mobility, we design a wearable and self-powered metronomic PDT (mPDT) system for chronic wound infection treatment. A flexible alternative current electroluminescent (ACEL) device is constructed through sandwiching an emissive layer between conductive hydrogel electrodes. This ACEL device works as a therapeutic patch by loading photosensitizer (PS) in its bottom hydrogel electrode, thus aviods the intravenous administration to patients. Under the triboelectric nanogenerator generated AC pulse, the electroluminescence produced from emissive layer can be absorbed by the PS-loaded electrode to generate reactive oxygen species for mPDT. Benefited from its arbitrary tailorability, this device can be customized into on-demand shapes and sizes. Using diabetic infected wound as a model condition, this ACEL mPDT device effectively eliminates drug-resistant bacteria and accelerates wound healing. Thus, the body-worn optoelectronic device successfully avoids the utilization of extracorporeal physical light and power sources, providing a promising strategy for convenient, user-friendly, and prolonged treatment of superficial diseases. [ABSTRACT FROM AUTHOR]

Materials that can emit light under optical/mechanical stimulation are usually called photoluminescent/mechanoluminescent (PL/ML) materials. PL materials are used in diverse fields for half a century. While, ML materials have burst out in the last two decades, and now are showing great application potential in the fields of anti‐counterfeiting, information storage, and stress imaging. It is of great significance to explore new luminescent materials with PL and ML dual response. In this study, Tb3+‐doped Ca3Ga4O9 phosphors with color‐tunable PL and non‐pre‐irradiation ML properties are reported. Ca3Ga4O9 exhibits a broadband blue emission centering at 425 nm, which originates from the 4T2‐4A2 transition of electrons in d orbits of Ga3+. Due to the energy transfer from host to Tb3+, color‐tunable emission from blue to cyan, and ultimately to green can be realized by increasing the concentration of Tb3+. Particularly, ML is seen from Ca3Ga4O9:Tb3+ under grinding and from the Ca3Ga4O9:Tb3+/PDMS film under bending or stretching originated from the triboelectric mechanism. The non‐pre‐irradiation ML behavior is evidenced by the contrast thermoluminescence (TL) experiments. This study not only provides a new candidate toward multi‐purpose luminescent applications, but also demonstrates a good case in which the triboelectric effect can efficiently trigger the non‐pre‐irradiation ML behavior. [ABSTRACT FROM AUTHOR]

Metal–organic frameworks (MOFs) have emerged as promising materials for triboelectric nanogenerators (TENGs), but the effects of ligand choice on triboelectric charge remain underexplored. Hence, this paper demonstrates the effect of single, binary, and ternary ligands on TENG performance of cobalt/cerium‐based (Co─Ce) bimetallic MOFs utilizing 2‐methylimidazole (2Melm), terephthalic acid (BDC), and benzene tricarboxylic acid (BTC) as ligands. The detailed structural characterization revealed that varying ligand chemistries led to distinct MOF features affecting TENG performance. Single ligand bimetallic MOFs (designated as CoCe‐2MeIm, CoCe‐BDC, CoCe‐BTC) has lower performance than binary ligand (designated as CoCe‐2MeIm‐BDC, CoCe‐2MeIm‐BTC, CoCe‐BDC‐BTC) and ternary ligand MOFs (designated as CoCe‐2MeIm‐BDC‐BTC). Among all, the binary ligand MOF, CoCe‐2MeIm‐BTC, shows the best results (598 V, 26.7 µA) due to the combined effect of imidazole ring and (─COO─) groups. This is attributed to lone pairs on nitrogen atoms and a delocalized π‐electron system in imidazole system in this material. CoCe‐BTC has the lowest results (31 V, 3.2 µA) due to the bulkier nature of the electron‐withdrawing (─COO─) groups and their impact on the π‐electron system of the benzene ring. This study showcases the potential of ligand chemistry manipulation to control triboelectric charge and thereby enhance MOF‐based TENG performance. [ABSTRACT FROM AUTHOR]

Polyvinyl alcohol (PVA), a versatile polymer, is extensively used across many industries, such as chemicals, food, healthcare, textiles, and packaging. However, research on applying PVA to triboelectric nanogenerators (TENGs) remains limited. Consequently, we chose PVA as the primary material to explore its contact electrification mechanisms at the molecular level, alongside materials like Polyethylene (PE), Polyvinylidene fluoride (PVDF), and Polytetrafluoroethylene (PTFE). Our findings show that PVA has the highest band gap, with the smallest band gap occurring between the HOMO of PVA and the LUMO of PTFE. During molecular contact, electron transfer primarily occurs in the outermost layers of the molecules, influenced by the functional groups of the polymers. The presence of fluorine atoms enhances the electron transfer between PVA and PTFE to maximum levels. Experimental validation confirmed that PVA and PTFE contact yields the highest triboelectric performance: VOC of 128 V, ISC of 2.83 µA, QSC of 82 nC, and an output power of 384 µW. Moreover, P-TENG, made of PVA and PTFE, was successfully applied in self-powered smart devices and monitored human respiration and bodily movements effectively. These findings offer valuable insights into using PVA in triboelectric nanogenerator technologies. [ABSTRACT FROM AUTHOR]

This work shows that various polyurethanes (FPUs) prepared using biomass-derived furan diols can be applied as promising tribopositive materials. The elastic FPUs having appropriate glass transition temperature (Tg) could be incorporated into polyethylene terephthalate (PET) fabrics to form FPU/PET films. The optimal FPU-4/PET film showed promising triboelectric performance with output voltages (Vp–p) up to 405 V and a maximum power density (Pmax) of 32 mW cm−2. [ABSTRACT FROM AUTHOR]

Sliding mode triboelectric nanogenerators (S‐TENG) have been validated as a simple and efficient mechanical energy harvesting technology in low frequency for constructing self‐powered systems. However, the charge invalid transfer in the S‐TENG leads to its output energy loss, which has not been addressed by researchers in this field. Herein, a novel transverse‐asymmetric electrode structure sliding TENG (TAE‐TENG) is proposed, where the specific asymmetric bottom electrode configuration distinguishes it from the previously reported S‐TENGs. This design can be equivalent to a hybrid model, consisting of two units, a sliding mode TENG with blank area and a freestanding mode TENG with a shielding electrode, which effectively eliminates the charge transfer loss and enhances the output performance. The insight mechanism of charge transfer in each operation process is analyzed. The TAE‐TENG achieves 1.42 µC output charge, 1.97‐fold as that of the conventional S‐TENG (0.72 µC) with equivalent dimensions, and also exhibits more sustained and higher current waveforms. The output charge, root‐mean‐square (RMS) current, and average power of the rotation‐TAE‐TENG at 60 rpm are 3.05 µC, 97.50 µA and 44.02 mW, respectively. This work provides a physical mechanism of charge transfer in sliding TENG and an effective method to improve its output energy. [ABSTRACT FROM AUTHOR]

The development of triboelectric nanogenerators (TENGs) using sustainable materials addresses the global electronic waste issue. This research focuses on fabricating a TENG device with biodegradable polylactic acid (PLA) as the tribopositive material and polytetrafluoroethylene (PTFE) as the tribonegative material. ZnFe2O4 nanoparticles are incorporated into the PLA matrix to enhance surface charge density and synthesised via a simple combustion method. PLA-ZnFe2O4 composite films were prepared by solvent casting with varying nanofiller content (0.25, 0.45, 0.65, and 0.85 g). Prepared composites were characterised by Powder X-ray Diffraction (PXRD) for crystalline nature and phase purity, Fourier Transform Infrared Spectroscopy (FTIR) for vibrational analysis, and Scanning Electron Microscopy (SEM) for surface morphology. The inclusion of ZnFe2O4 nanoparticles improves TENG output performance, with a maximum output voltage of 18.4 V and a current of 1.57 µA observed for a PLA (poly(lactic acid)) composite with 39.39% nanoparticle content. Electrical studies on the optimised device show successful charging of various capacitors and powering 20 LEDs and a calculator. Body movements like walking and jumping were also tested to measure voltage and current outputs. These findings highlight new possibilities for developing smart, self-powered electronic devices. [ABSTRACT FROM AUTHOR]

Triboelectric nanogenerators (TENGs) have been widely used to harness various forms of mechanical energy for conversion to electrical energy. However, the contentious challenge in characterising TENGs is the lack of standard protocols for assessing mechanical‐to‐electrical energy conversion processes. Herein, macroscopic signal analysis is used to identify three key charging events within triboelectric signals: charge induction (CI), contact electrification (CE), and electrostatic discharge (ESD). By considering two phases of motion during contact‐separation (approach and departure of the contact materials), CI arising from the motion of bound surface charge (varying electric field) between opposing contact materials is shown to dominate the measured displacement current signal, rather than the process of CE itself. Furthermore, the conventional signal (i. e. voltage, current, charge) interpretation of CE and CI during approach and departure phases is re‐assessed, to indicate that the sudden spike of current often observed immediately prior to contact (or after separation) arises from polarity inverting electrostatic discharge (ESD). This aspect of the measured triboelectric effect, which is often ignored, is crucial for the design of TENGs and hence, techniques to enhance the understanding and control over the stochastic occurrence of ESDs is explored. The methods proposed for the deconvolution of the macroscopic signal components of TENGs, and mitigation of ESD occurrences, will allow for precise quantification of the associated charging events. The applications of this study will template the design and development of future super‐TENGs with optimised energy conversion capabilities. [ABSTRACT FROM AUTHOR]

Extraction of U(VI) in water is of great significance in energy and environmental fields. However, the traditional methods usually fail due to the indispensable extra addition of catalyst, adsorbent, precipitant, or sacrificial agents, which may lead to enhanced extraction costs and secondary pollution. Here, a new efficient uranium extraction strategy is proposed based on triboelectricity without adding a catalyst or other additives. It is found only under the friction between the microbubbles (generated under ultrasonication) and the water flow, that reactive oxygen species (ROS) can largely be generated, which thus contributes to the solidification of U(VI) from water. In addition, the magnetic field can affect the phase of the product. Under mechanical stirring, the product contains (UO2)O2·2H2O, while which contains UO2(OH)2 and (UO2)O2·4H2O under the magnetic stirring. Quenching experiments are also carried out to explore the influence of environmental factors. Most importantly, it shows great potential in the extraction of U(VI) from seawater. This work proposes a catalyst‐free and light‐free strategy toward the solidification of U(VI) from water, which avoids the secondary pollution of the catalyst to the environment and is low‐cost, and has great potential in the real application. [ABSTRACT FROM AUTHOR]

As large‐area and optically transparent photon harvesting devices, luminescent solar concentrators (LSCs) are promising candidates for building‐integrated photovoltaics owing to their high transmittance and resistance to shadowing effects existing in solar cells. Up to now, there are still many challenges in the practical application of LSCs: 1) Reabsorption loss is inevitable during photoluminescence transmission due to indirect illumination of solar cells in LSC system. 2) Satisfactory energy harvesting cannot be achieved in rainy conditions due to the substantial attenuation of the incident light intensity. 3) Evaporation residue on the surface of LSCs leads to device performance degradation. Pioneering researches and feasible strategies for reabsorption loss suppression, energy harvesting in rainy days as well as self‐cleaning property are still lacking demonstration. In this work, reabsorption loss is suppressed based on advanced structural LSCs with universally applicable optical spacer layer. Then the integrated LSCs with droplet‐based electricity generator (DEG) are proposed for the first time. Such DEG‐LSCs not only realize synergistic harvesting of solar and raindrop energy, but also possess self‐cleaning properties. Finally, a self‐powered temperature and humidity sensing system is designed and demonstrated to provide feasible ideas for the practical application of DEG‐LSCs in self‐powered intelligent buildings. [ABSTRACT FROM AUTHOR]

Hybrid nanogenerators are advanced mechanical energy harvesters capable of simultaneously scavenging multiple types of energy. Additionally, thermochromic materials provide a practical and visually assessable method for real‐time temperature monitoring. In this report, a novel energy harvester and sensing patch (EHSP) is introduced, that utilizes combined piezoelectric and triboelectric effects to harvest mechanical energy efficiently. To optimize the EHSP, various energy harvester configurations are fabricated and tested, and the dielectric properties of triboelectric films are systematically investigated. These improvements are implemented to augment the overall energy harvesting capability. The thermochromic properties of the EHSP are also explored to enhance both the electrical performance and thermal responsiveness. The EHSP demonstrates the ability to generate maximum voltage and current outputs of 350 V and 20.4 µA, respectively. Moreover, it can detect temperature changes within seconds, making it suitable for both energy harvesting and sensing applications. The EHSP is tested in practical scenarios, proving its efficiency as an energy harvester and sensor for everyday human activities. Furthermore, its integration with multiple hybrid nanogenerators showcases its potential for industrial and wearable sensing applications. [ABSTRACT FROM AUTHOR]

This study presents a freestanding sliding triboelectric nanogenerator (FS‐TENG) designed for low‐frequency motions (below 2 Hz). However, for practical applications, an efficient power management strategy is required to handle the harmonic outputs of the FS‐TENG. The high‐frequency signal is not sustainable for powering low‐power electronic applications. To address the issue, a novel direct current power supply circuit (DPS) is proposed that utilizes a double charge circuit (DCC) and a comb filtering circuit (CFC) to efficiently harness harmonic sources from the FS‐TENG. The direct power supply (DPS) outperforms traditional converters by reducing the impedance of the FS‐TENG and collecting the target harmonic sources, which facilitates a continuous power supply to the load. The results demonstrate that the DPS is capable of providing a continuous DC voltage of 2.2 V to a 10 MΩ load with minimal ripple (0.039%) at a low operating frequency of 0.625 Hz. Additionally, the practical application of a self‐powered temperature sensor is demonstrated to highlight the potential of FS‐TENG and DPS for low‐frequency energy harvesting solutions in real‐world scenarios. [ABSTRACT FROM AUTHOR]

Research on tribocatalysis, which involves the triboelectric effect, is based on the concept that friction between dissimilar materials can generate charges capable of initiating catalytic reactions. This phenomenon holds significant potential for the degradation of wastewater contaminants in the environment. In this study, pure and Ce-modified (2 mol%) ZnO powders were investigated as tribocatalysts for the degradation of doxycycline (DC), a tetracycline antibiotic, in the absence of light. The research demonstrates that friction between the catalyst, the beaker, and the polytetrafluoroethylene (PTFE) magnetic rod induces charge transfer at their interfaces, leading to the breakdown of pollutants. Additionally, doxycycline degradation was observed at three different stirring speeds (100, 300, and 500 rpm). The results confirmed the tribocatalytic effect, showing that DC degradation increases with higher stirring speeds. Using ZnO and ZnO/Ce powders, maximum degradations of 80% and 55%, respectively, were achieved in 24 h at a stirring speed of 500 rpm. The findings of this study suggest that these samples can effectively degrade contaminants in water through the application of mechanical energy. [ABSTRACT FROM AUTHOR]

This article investigates the performance of a contact-mode Triboelectric Nanogenerator (TENG) utilizing polydimethylsiloxane (PDMS) with nano gratings as a dielectric in a metal-dielectric configuration. The evaluation encompasses the impact of gratings, tapping frequency, various load conditions, and contact area on the TENG performance. The fabrication involves spin-coating PDMS onto a master mold to create the device. Experimental measurements reveal a significant enhancement of 97% in open-circuit voltage by introducing gratings on PDMS. Furthermore, as the tapping frequency increases from 1 Hz to 3 Hz, there is a corresponding rise of 108% in output voltage. The influence of load resistance on TENG output performance demonstrates its ability to drive different loads efficiently. Moreover, enlarging the contact area of the device substantially increases the open-circuit voltage. A device with a 400 mm2 contact area can generate a voltage of 80 V at a low frequency of 3 Hz, indicating the importance of considering device size and contact area for specific applications. A practical circuit integrating a TENG with a full-wave bridge rectifier demonstrates energy harvesting capabilities by successfully illuminating a light-emitting diode (LED) and charging various capacitors. The fabricated devices exhibit better performance along with a cost-effective and easy fabrication process. [ABSTRACT FROM AUTHOR]

The harnessing and utilization of mechanical energy through frictional route have emerged as a promising avenue for advancing clean energy initiatives. Triboelectric charges are generated on the surface of two different materials during friction. These charges are similar to photocatalytic charges and can be utilized for dye degradation by a process called tribocatalysis. In this study, it was found that lithium borate bismuth tungstate (0.7 L i 2 B 4 O 7 − 0.3 B i 2 W O 6) nanocrystal glass-ceramics synthesized by melt-quench technique exhibit excellent tribocatalytic dye degradation performance by harvesting friction energy. X-ray diffraction technique, Raman Spectroscopy and Transmission Electron Microscopy (TEM) was performed to examine the structure, phase, and microstructure of the prepared samples. The maximum tribocatalytic decomposition of Methylene Blue (MB) dye observed was 56 % for as-quenched sample (AQ) and 74 % for heat-treated sample (HT) after 10 h of mechanical stirring at 700 rpm and for Rhodamine B (RhB) dye the degradation achieved was 34 % and 64 % in 8 h for AQ and HT respectively. Due to their superior dye decomposition capabilities, glass-ceramic crystals hold significant promise for harnessing mechanical energy through friction in wastewater treatment processes. [ABSTRACT FROM AUTHOR]

Triboelectric nanogenerators (TENGs) have emerged as a promising technology to harvest electrical energy from natural motions such as human movement, wind, and water flow. Although TENGs show significant potential in small-scale applications, developing large-scale TENGs capable of generating high power remains a significant challenge. Several factors that can affect the performance of large-scale TENGs are being investigated to overcome this challenge, including the size and configuration of dielectric materials. This study optimizes dielectrics regarding surface area, thickness, and multicell configuration to improve harvested electrical power density in large-scale TENGs. In the studies, glass fiber was used as the positive dielectric, and multipurpose white silicone was used as the negative dielectric because of their high tribo-potential, durability, and easy accessibility. In the size optimization phase, dielectric thicknesses and surface areas that provide the maximum power density were determined. Subsequently, horizontal and vertical multicell configurations were examined to efficiently integrate size-optimized dielectrics. The results reveal that large-scale TENGs with vertical multicell configurations can achieve high and usable energy density for electronics. The findings provide valuable insight into the development of large-scale TENGs with advanced power generation capabilities. [ABSTRACT FROM AUTHOR]

Nanogenerators have garnered significant interest as environmentally friendly and potential energy-harvesting systems. Nanogenerators can be broadly classified into piezo-, tribo-, and hybrid nanogenerators. The hybrid nanogenerator used in this experiment is a nanogenerator that uses both piezo and tribo effects. These hybrid nanogenerators have the potential to be used in wearable electronics, health monitoring, IoT devices, and more. In addition, the versatility of the material application in electrospinning makes it an ideal complement to hybrid nanogenerators. However, despite their potential, several experimental variables, biocompatibility, and harvesting efficiency require improvement in the research field. In particular, maximizing the output voltage of the fibers is a significant challenge. Based on this premise, this study aims to characterize hybrid nanogenerators (HNGs) with varied structures and material combinations, with a focus on identifying HNGs that exhibit superior piezoelectric- and triboelectric-induced voltage. In this study, several HNGs based on coaxial structures were fabricated via electrospinning. PVDF-HFP and PAN, known for their remarkable electrospinning properties, were used as the primary materials. Six combinations of these two materials were fabricated and categorized into homo and hetero groups based on their composition. The output voltage of the hetero group surpassed that of the homo group, primarily because of the triboelectric-induced voltage. Specifically, the overall output voltage of the hetero group was higher. In addition, the combination group with the most favorable voltage characteristics combined PVDF-HFP@PAN(BTO) and PAN hollow, boasting an output voltage of approximately 3.5 V. [ABSTRACT FROM AUTHOR]

Producing biomechanical energy from waste polymer has attracted lot of interest in this digital era as a number of benefits can be accounted for this including: (i) addressing challenges in the disposal of waste materials, and pollution (air, water, soil) caused by their presence in the atmosphere (ii) ensuring clean and affordable energy at low cost (iii) avoiding the hassle of constant battery replacement, charging, and long wires for charging, and so on. Here, the authors aim at the recycling of waste materials, especially polymers, keeping the 4R's of effective waste management in mind. Energy harvesters based on triboelectric/piezoelectric effects convert energy from vibrational waves and material deformations into electricity. A hybrid energy harvester is constructed, with waste polymer to act as the tribo-active layer, nanomaterial coating is applied to induce piezoelectricity and Al as the electrode. The energy harvester demonstrated an output voltage enhancement of 266.166% for qualitative input conditions and 375.374%, 337.33%, and 287.308% for quantized input conditions (1 N, 1.5 N, 3 N respectively) when compared with the performance of raw waste polymer-based energy harvester. The developed device could drive low-power portable electronic devices, such as LEDs, calculator, digital watch, thermometer and pedometer. [ABSTRACT FROM AUTHOR]

The functionalized polymer with scalable properties presents a promising option for flexible triboelectric nanogenerators designed for detecting human motion. In this study, a novel method to fabricate tribopositive composite film was proposed by incorporating high permittivity N-doped orange peel-based carbon dots (O-CDs) into the highly cross-linked polyvinyl alcohol (PVA). The O-CDs/PVA sensor showed elevated electrical output with the raised content of O-CDs until 1.5 wt. % with a peak voltage of 3.5 V. The response characteristics under various external force conditions were tested, and the maximum peak voltage and current reached 3.92 V and 28.6 A under the force of 50 N. Moreover, O-CDs/PVA sensors present superior high-output stability, durability, and accurate distinction to different movement states, even the vocal cord vibration. By introducing the support vector machine learning algorithm, intelligent gesture recognition was achieved. This work paves a facile, feasible, and scalable pathway to the self-powered human motion sensor device. [ABSTRACT FROM AUTHOR]

Polystyrene (PS) is a very common material in packaging. In this study, it is recycled by turning it into energy harvesting devices: triboelectric generators. Herein, heat‐pressed films of recycled PS are formed and their surfaces are modified physically and chemically. The triboelectric properties of the films are determined using a dynamic testing machine, and the performance of the triboelectric generators is evaluated with a high‐speed contact–separation system. The developed charge density of the triboelectric generator increases two orders of magnitude—from 0.03 to 1.52 nC cm−2—by combining these surface modification methods. Such high values of charge density enable the production of single material triboelectric generators. [ABSTRACT FROM AUTHOR]

The increasing need for wearable and portable electronics and the necessity to provide a continuous power supply to these electronics have shifted the focus of scientists toward harvesting energy from ambient sources. Harvesting energy from ambient sources, including solar, wind, and mechanical energies, is a solution to meet rising energy demands. Furthermore, adopting lightweight power source technologies is becoming more decisive in choosing renewable energy technologies to power novel electronic devices. In this regard, piezoelectric nanogenerators (PENGs) based on polymer composites that can convert discrete and low-frequency irregular mechanical energy from their surrounding environment into electricity have attracted keen attention and made considerable progress. This review highlights the latest advancements in this technology. First, the working mechanism of piezoelectricity and the different piezoelectric materials will be detailed. In particular, the focus will be on polymer composites filled with lead-free BaTiO3 piezoceramics to provide environmentally friendly technology. The next section will discuss the strategies adopted to enhance the performance of BaTiO3-based polymer composites. Finally, the potential applications of the developed PENGs will be presented, and the novel trends in the direction of the improvement of PENGs will be detailed. [ABSTRACT FROM AUTHOR]

Triboelectric nanogenerator (TENG) cathodic protection technology based on new energy harvesting represents a promising strategy owing to the low cost, low environmental pollution and simple installation. However, converting alternating current to pulsed direct current through a rectifier reduces the cathodic protection efficiency. Here, a multi-phase coupling TENG (RD-TENG) energy harvesting device with rotating disc is proposed for metal cathode anticorrosion. Through the rotation of the disk, high density current is generated to form a DC power supply. The current output pulse interval is reduced after full wave rectification, and the effect of a constant and stable direct current (DC) power supply can be achieved. The highly coupled superposition RD-TENG (3P5E) demonstrates a short-circuit current density (Isc) of 1.86 μA, an open circuit voltage (Voc) of 120 V, and a transferred charge (Qsc) of 50 nC. At low speeds, RD-TENG (3P5E) can effectively power up to six LED bulbs without any noticeable flickering. Furthermore, when 304 SS connected to RD-TENG (3P5E), the open circuit voltage and corrosion potential decreased by 102 mV and 122 mV respectively, indicating superior corrosion protection compared to systems without RD-TENG. In general, this advancement provides an important practical significance for TENGs in expanding the application of cathodic corrosion protection in the Marine industry. [ABSTRACT FROM AUTHOR]

Tribocatalysis is an emerging advanced oxidation process that utilizes the triboelectric effect, based on friction between dissimilar materials to produce charges that can initiate various catalytic reactions. In this study, pure and rare-earth-modified ZnO powders (La2O3, Eu2O3, 2 mol %) were demonstrated as efficient tribocatalysts for the removal of the tetracycline antibiotic doxycycline (DC). While the pure ZnO samples achieved 49% DC removal within 24 h at a stirring rate of 100 rpm, the addition of Eu2O3 increased the removal efficiency to 67%, and La2O3-modified ZnO powder exhibited the highest removal efficiency, reaching 80% at the same stirring rate. Additionally, increasing the stirring rate to 300 and 500 rpm led to 100% DC removal in the ZnO/La case within 18 h, with the pronounced effect of the stirring rate confirming the tribocatalytic effect. All tribocatalysts exhibited excellent recycling properties, with less than a 3% loss of activity over three cycles. Furthermore, a scavenger assay confirmed the importance of superoxide radical generation for the overall reaction rate. The results of this investigation indicate that the rare-earth-modified ZnO tribocatalysts can effectively utilize mechanical energy to decompose pollutants in contaminated water. [ABSTRACT FROM AUTHOR]

Conductive hydrogels are gaining significant attention as promising candidates for the fabrication materials for flexible electronics. Nevertheless, improving the tensile properties, hysteresis, durability, adhesion, and electrochemical properties of these hydrogels remains challenging. This work reports the development of a novel semi‐interpenetrating network poly(ionic liquid) hydrogel named PATV, via the in situ polymerization of acrylamide, N‐[Tris(hydroxymethyl)methyl] acrylamide, and 1‐vinyl‐3‐butylimidazolium tetrafluoroborate. The density functional theory calculations reveal that the poly(ionic liquid) in the hydrogel network acts as physical cross–linking points to construct hydrogen‐bond networks. Furthermore, the hydrogen‐bond networks dissipate energy efficiently and quickly, and thus stress concentration and hysteresis are avoided. The prepared hydrogel has a low hysteresis (9%), high tensile properties (900%), fast response (180 ms), high sensitivity (gauge factor = 10.4, pressure sensitivity = 0.14 kPa−1), and wide sensing range (tensile range: 1–600%, compression range: 0.1–20 kPa). A multifunctional sensor designed based on the designed hydrogel enables real‐time, rapid, and stable response‐ability for the detection of human movement, facial expression recognition, pronunciation, pulse, handwriting, and Morse code encryption. Furthermore, the assembled triboelectric nanogenerator displays an excellent energy harvesting capability, thus highlighting its potential application in self‐powered flexible wearable electronic devices. [ABSTRACT FROM AUTHOR]

Recent developments in robotics increasingly highlight the importance of sensing technology, especially tactile perception, in enabling robots to effectively engage with their environment and interpret physical interactions. Due to power efficiency and low cost, the triboelectric mechanism has been frequently studied for measuring pressure and identifying materials to enhance robot perception. Nevertheless, there has been limited exploration of using the triboelectric effect to detect curved surfaces, despite their prevalence in daily lives. Here, a triboelectric multimodal tactile sensor (TMTS) of multilayered structural design is proposed to recognize distinct materials, curvatures, and pressure simultaneously, thus decoupling different modalities to enable more accurate detection. By attaching sensors to robotic fingertips and leveraging deep learning analytics, the quantitative curvature measurement provides more precise insights into an object's detailed geometric characteristics rather than merely assessing its overall shape, hence achieving automatic recognition of 12 grasped objects with 99.2% accuracy. The sensor can be further used to accurately recognize the softness of objects under different touch gestures of a robotic hand, achieving a 94.1% accuracy, demonstrating its significant potential for wide‐ranging applications in a future robotic‐enabled intelligent society. [ABSTRACT FROM AUTHOR]

Poly(vinylidene fluoride) (PVDF) based conducting polymer composites with carbon nanomaterials can be used for mechanical energy harvesting through piezoelectric or triboelectric effect. This study aims to investigate the influence of PMMA molecular weight on the electrical, thermal, and wetting properties of PVDF/40 wt.% PMMA blend nanocomposites reinforced with expanded graphite (ExGr). The blend nanocomposites with 40 wt.% PMMA have been prepared by solution blending method by using two different molecular weights of PMMA whose melt flow indices are 2 g/10 min and 2.3 g/10 min. The coexistence of the electroactive gamma and non-polar alpha phases of PVDF in the blend nanocomposites has been confirmed by X-ray diffraction, Fourier transform infrared spectroscopy and differential scanning calorimetry analyses. While overall crystallinity (%) of low molecular weight PMMA employed blend nanocomposites is lower than that of high molecular weight PMMA blended nanocomposites, the electroactive gamma phase has been found to increase in the former blend nanocomposites. The dispersion of graphite nanosheets has been observed to be better in high molecular weight PMMA employed blend nanocomposites which results in higher electrical conductivity. Impedance analysis of PVDF-40 wt.% PMMA-2 wt.% ExGr blend nanocomposite with high molecular weight PMMA results in enhanced interjunction capacitance (74.5 pF) in comparison to low molecular weight PMMA mixed blend nanocomposites (68 pF). Water contact angle (WCA) increases with molecular weight of PMMA and ExGr loading level. Thermogravimetric analysis has shown that the char content (above 500°C) is slightly higher for the blend with low molecular weight PMMA than with high molecular weight PMMA. [ABSTRACT FROM AUTHOR]

This document is an editorial from the journal Pharmaceutics, which celebrates its 15th anniversary and highlights advancements in process and formulation modeling in the pharmaceutical industry. The editorial emphasizes the significance of modeling in product development and discusses different types of models available to scientists and engineers. It also provides a summary of the articles included in a special issue of the journal, covering topics such as nanosuspensions, computational techniques, laser ablation, and wet granulation. The editorial concludes by summarizing the main findings from each contribution in the special issue. These studies offer valuable insights into improving drug delivery efficiency and enhancing pharmaceutical manufacturing processes. [Extracted from the article]

AbstractFree-fall tribo-electrostatic separators have long been used for sorting granular plastic wastes. The aim of this paper is to propose a modified configuration of the electrode system of such a separator and validate its effectiveness for processing a mixture of polyethylene (PE) and polypropylene (PP) flakes originating from the processing of packaging waste at GRANUPLAST Company, Jassans-Riottier, France. The mixture to be treated is not homogeneous and consisted of roughly 2/3 PE and 1/3 PP. The granular mixture samples were charged by triboelectric effect in a fluidized bed device, and then introduced into a laboratory-scale free-fall electrostatic separator. Preliminary tests were conducted to ascertain the mass of the mixture to be introduced in the fluidized bed and the duration of the charging process. Better results were obtained with the modified electrode configuration of the free-fall electrostatic separator. Thus, from 100 g of mixed flakes, 98.2% of PE and 96.6% of PP were recovered with purities of 99.1% and 98%, respectively. In addition, numerical modeling of the PP and PE particles trajectory was performed to simulate the behavior of charged particles in the standard and modified electrode configurations. Work is in progress for the industrial implementation of this tribo- electrostatic separation technology. [ABSTRACT FROM AUTHOR]

Tribocatalysis is a promising environmental remediation technique that utilizes the triboelectric effect, produced when dissimilar materials interact through friction, to generate charges promoting catalytic reactions. In this work, the tribocatalytic degradation of an organic dye—Rhodamine B (RhB)—has been experimentally realized using pure and 2 mol.% La-modified/ZnO powders, synthesized via a simple hydrothermal method. The effects of annealing on the tribocatalytic activity of the La/ZnO catalysts are also studied at 100 and 500 °C. The La/ZnO-modified catalysts showed an enhanced RhB degradation efficiency with 92% removal within 24 h, compared to only 58% for the pure ZnO. The effects of annealing were found to be detrimental, with RhB removal efficiencies dropping from 92 to 69% in the 100–500 °C range. The catalysts' cycling stability was found to be excellent within three cycles. Ultimately, it is demonstrated that by utilizing La/ZnO powders, contaminated wastewater can be efficiently treated through employing tribocatalysis. [ABSTRACT FROM AUTHOR]

The separation of plastic mixtures from waste electrical and electronic equipment is an increasingly active domain of research. Several electrostatic separation processes and devices have been developed to recover plastic waste. All these processes are based on the use of the triboelectric effect to charge the plastic granules to separate them in an intense electric field. The objective of this study is to investigate the effect of ambient humidity on the efficiency of the triboelectric charging and electrostatic separation process, especially in an industrial environment where granular plastic waste may contain residual moisture due to previous processing by flotation or inappropriate storage. The experiments were carried out using a rotating-multi-cylinder tribocharger and a roll-type electrostatic separator. The samples were composed in equal proportions of either: (1) acrylonitrile butadiene styrene (ABS) and polystyrene (PS) or (2) polypropylene (PP) and polyethylene (PE), the average particle diameter of which was between 2 and 6 mm. The efficiency of the tribo-electrostatic separation was evaluated by measuring the purity and recovery of the products. The results confirm that separating (ABS + PS) and (PP + PE) mixtures is feasible. The best separation results were obtained when the materials were stored and processed at an ambient relative humidity of around 50%. [ABSTRACT FROM AUTHOR]