Search

The conventional method for FWT and OBT analysis is a liquid scintillation counting method after freeze-drying and combustion of the sample. However, pretreatment for FWT and OBT analysis are complicated and time consuming processes over weeks. Thus, we propose the application of microwave heating technique to save time and effort of the pretreatment of plant samples for FWT analysis. To understand the behavior of the combustion and drying of organic samples, we conducted TG/DTA analysis of pine needle samples. It is found that the sample has to be heated up to 100 - 110 ℃ for complete drying under N2 gas flow condition. Then, we tried the water recovery from fresh pine needle samples by the multi-mode microwave heating system. As a results, it was provided to good recovery yield achieved more than 97% under these experimental conditions. This result shows more preferable for the pretreatment of organic samples by microwave irradiation method than the conventional method., source:https://doi.org/10.1585/pfr.11.2405017, identifier:0000-0001-9074-115X

To estimate the environmental transfer of tritium into the atmosphere and to establish tritium analysis techniques, this study improves our previous compartment model and proposes new analytical technique based on the microwave heating method and a water-sample purification technique using ion resin. This article introduces a new conceptual approach for estimating environmental tritium behavior., source:https://doi.org/10.1585/pfr.14.3405099, identifier:0000-0003-3140-1061

This paper presents an evaluation of a rapid pretreatment method for tritium analysis, that uses ion exchange resins (the batch method). The standard water samples were prepared with river water collected in Okinawa, Japan. Powdex resin was used in this study, which is an ion exchange resins in the form of powder beads. First, 100 mL of the standard sample was stirred with the cation exchange (PCH) and anion exchange (PAO) resins, as well as with activated carbon. To determine the optimal stirring time, we tested stirring times of 5, 10, 20 and 30 min. Additionally, to determine a suitable amount of ion exchange resin for environmental water samples, variations in the amount of resin and activated carbon were tested. Under the conditions of Experiment-3 (0.3 g, 0.3 g and 0.6 g of PCH, PAO and activated carbon, respectively) and with a stirring time of 5 min, electrical conductivity values of less than 1 mSm−1 were achieved. These results demonstrate the effectiveness of the removal of impurities in the sample water by ion exchange resins and confirm that such an effect can be achieved during a short period of time (i.e., in 5 min)., source:https://doi.org/10.1585/pfr.15.2405027, identifier:0000-0002-0580-0328

This paper presents an evaluation of a rapid pretreatment method for tritium analysis, that uses ion exchange resins (the batch method). The standard water samples were prepared with river water collected in Okinawa, Japan. Powdex resin was used in this study, which is an ion exchange resins in the form of powder beads. First, 100 mL of the standard sample was stirred with the cation exchange (PCH) and anion exchange (PAO) resins, as well as with activated carbon. To determine the optimal stirring time, we tested stirring times of 5, 10, 20 and 30 min. Additionally, to determine a suitable amount of ion exchange resin for environmental water samples, variations in the amount of resin and activated carbon were tested. Under the conditions of Experiment-3 (0.3 g, 0.3 g and 0.6 g of PCH, PAO and activated carbon, respectively) and with a stirring time of 5 min, electrical conductivity values of less than 1 mSm^<−1> were achieved. These results demonstrate the effectiveness of the removal of impurities in the sample water by ion exchange resins and confirm that such an effect can be achieved during a short period of time (i.e., in 5 min).

To estimate the environmental transfer of tritium into the atmosphere and to establish tritium analysis techniques, this study improves our previous compartment model and proposes new analytical technique based on the microwave heating method and a water-sample purification technique using ion resin. This article introduces a new conceptual approach for estimating environmental tritium behavior.