Search

Battery electric vehicles (BEVs) are increasingly recognized as the key to the power industry’s shift towards decentralization, carbon neutrality, and electrification because of their potential as flexible assets. Advances in grid integration, communication standards, smart charging, vehicle-to-grid technology, and electric vehicle service platforms are crucial for effectively leveraging BEVs. However, realizing these potential hinges on the active participation of electric vehicle owners, which is a vital yet challenging aspect. This study proposes a gamification-based incentive model to boost the participation of BEV owners in demand response programs, focusing on enhancing grid flexibility. A pilot project involving BEV drivers and charging-point operators was conducted on Jeju Island, South Korea. The significant contributions of this study include the development of both hardware and software systems for the gamification model and an ANOVA analysis to assess its impact. Compared with conventional economic incentives, the application of gamification-based incentives had effects of 13.8–69.2 percent from a demand increase perspective and 2.0–91.4 percent from a demand reduction perspective.

Operating virtual power plants (VPP) solely based on economic feasibility can cause stability problems, such as voltage violation and power congestion in the distribution system. A cooperation-based operation between the VPP and distribution system operator (DSO) is regarded one of the methodologies for solving stability problems. In the cooperation-based operation method, a VPP establishes an operation strategy considering the information provided beforehand by the DSO, such as the distribution system constraint (DSC). The DSC is uncertain because it is determined based on the forecasted grid situation. Therefore, operational strategies that rely only on the DSCs provided by DSOs may make the operation of the VPP passive and reduce profits depending on the accuracy of the announced DSCs. This study proposes an operating methodology and optimal operation model considering the uncertainty of the DSC to increase the profit of the VPP. In the proposed model, the VPP independently forecasts the DSC for profit maximization and establishes an operational plan considering penalties. Case studies were conducted to demonstrate the economic improvement of the VPP, considering the uncertainty of the DSC. The case study results demonstrated that the proposed model increased the profit of the VPP by 1.6 % compared with that of the conventional method.

Abstract In this study, major chemical components of PM2.5 including nitrate, sulfate, organic carbon (OC), and elemental carbon (EC) were measured in Chuncheon, South Korea in May–June, 2021. Average PM2.5 concentration was 16.4±9.7 µg m−3, and OC was the largest contributor of PM2.5 mass concentration. High concentration episodes (HCEs), defined when PM2.5 concentration exceeded 30 µg m−3, were caused by Asian dust, secondary inorganic aerosol (SIA) formation, and primary OC emission. NH4+ was determined to be a limiting factor for SIA formation based on neutralization ratio. There was statistically significant correlation between n-alkanes and PM2.5, and odd alkanes including C27, C29, and C31, which are generally emitted from biogenic sources, were abundant species, suggesting the importance of natural sources over fossil fuel combustion. Polycyclic aromatic hydrocarbons (PAHs) concentrations were significantly lower than those measured at the same sampling site in 2014–2015. Based on the diagnostic ratios of PAHs, vehicular emission, rather than solid fuel emission, were significant for PAHs. Detailed characterization of chemical composition of PM2.5 reported in this study can be of great help in establishing an appropriate abatement policy to reduce PM2.5 concentrations.

Abstract Veterinary biocides used in animal husbandry have the potential to cause human health concerns. Biocidal products for veterinary use, which contain pesticides approved in Korea, comprise 49 active ingredients within 234 products. Within 17 of these products there are 3 ingredients which are highly hazardous pesticides: coumaphos, dichlorvos and methomyl. In this study, the content of the active ingredients of 160 products sold domestically was investigated. Samples were collected for 119 biocidal products for veterinary use. These were analysed by high‐performance liquid chromatography (HPLC) and gas chromatography (GC). Seventeen products were noncompliant (insufficient or excess quantity of active ingredients). The ingredients that were below the stated concentrations were amitraz, chlorpyrifos‐methyl, cypermethrin, cyromazine, dichlorvos, fipronil, muscamone and trichlorfon. The ingredients that exceeded the stated concentrations were abamectin, fluvalinate and pyriproxyfen. The noncompliance rate in biocidal products for veterinary use was 9.19%. The results of this study show that three highly hazardous pesticides (coumaphos, dichlorvos and methomyl) and 10 active ingredients (abamectin, amitraz, chlorpyrifos‐methyl, cypermethrin, cyromazine, fipronil, fluvalinate, muscamone, pyriproxyfen and trichlorfon) deviated from the stated concentrations. Thus, management plans should be established to ensure compliant veterinary drugs by post‐distribution quality control, such as planning for regular inspection.

The implementation of an energy storage system (ESS) as a container-type package is common due to its ease of installation, management, and safety. The control of the operating environment of an ESS mainly considers the temperature rise due to the heat generated through the battery operation. However, the relative humidity of the container often increases by over 75% in many cases because of the operation of the air conditioner which pursues temperature-first control. Humidity is a major factor which can cause safety issues such as fires owing to insulation breakdown caused by condensation. However, the importance of humidity control in ESS is underestimated compared to temperature control. In this study, temperature and humidity monitoring and management issues were addressed for a container-type ESS by building sensor-based monitoring and control systems. Furthermore, a rule-based air conditioner control algorithm was proposed for temperature and humidity management. A case study was conducted to compare the conventional and proposed control algorithms and verify the feasibility of the proposed algorithm. The results showed that the proposed algorithm reduced the average humidity by 11.4% compared to the value achieved with the existing temperature control method while also maintaining the temperature.

Designing human-interactive displays enabling the simultaneous sensing, visualization, and memorization of a magnetic field remains a challenge. Here, the authors present a skin-patchable magneto-interactive electroluminescent display by employing a magnetic field-dependent conductive gate, thereby enabling 3D motion tracking.

Abstract Background The antibiotics generally used in farm animals are rapidly losing their effectiveness all over the world as bacteria develop antibiotic resistance. Like some other pathogenic bacteria multidrug-resistant strains of Salmonella enterica serovar Typhimurium (S. Typhimurium) are also frequently found in animals and humans which poses a major public health concern. New strategies are needed to block the development of resistance and to prolong the life of traditional antibiotics. Thus, this study aimed to increase the efficacy of existing antibiotics against S. Typhimurium by combining them with opportunistic phenolic compounds gallic acid (GA), epicatechin, epicatechin gallate, epigallocatechin and hamamelitannin. Fractional inhibitory concentration indexes (FICI) of phenolic compound-antibiotic combinations against S. Typhimurium were determined. Based on the FICI and clinical importance, 1 combination (GA and ceftiofur) was selected for evaluating its effects on the virulence factors of this bacterium. Viability of Rattus norvegicus (IEC-6) cell in presence of this antibacterial combination was evaluated. Results Minimum inhibitory concentrations (MICs) of GA, epigallocatechin and hamamelitannin found against different strains of S. Typhimurium were 256, (512–1024), and (512–1024) μg/mL, respectively. Synergistic antibacterial effect was obtained from the combination of erythromycin-epicatechin gallate (FICI: 0.50) against S. Typhimurium. Moreover, additive effects (FICI: 0.502–0.750) were obtained from 16 combinations against this bacterium. The time-kill assay and ultrastructural morphology showed that GA-ceftiofur combination more efficiently inhibited the growth of S. Typhimurium compared to individual antimicrobials. Biofilm viability, and swimming and swarming motilities of S. Typhimurium in presence of GA-ceftiofur combination were more competently inhibited than individual antimicrobials. Viabilities of IEC-6 cells were more significantly enhanced by GA-ceftiofur combinations than these antibacterials alone. Conclusions This study suggests that GA-ceftiofur combination can be potential medication to treat S. Typhimurium-associated diarrhea and prevent S. Typhimurium-associated blood-stream infections (e.g.: fever) in farm animals, and ultimately its transmission from animal to human. Further in vivo study to confirm these effects and safety profiles in farm animal should be undertaken for establishing these combinations as medications.

The beach vitex (Vitex rotundifolia L.), a member of the Lamiaceae family, is a salt-tolerant, woody perennial common in coastal areas worldwide. Plant–fungal association was monitored in the shoreline forest area of Wando Island in Korea in 2020, and leaf samples showing leaf spot disease were collected. Eight fungal isolates were recovered from the samples on PDA and identified based on the morphological characteristics and multilocus molecular phylogeny. Among the eight isolates, four were identified as Alternaria alternata, two as Fusarium humuli, one as Colletotrichum aenigma, and one as Stagonosporopsis caricae. Pathogenicity tests of the fungal isolates on the detached leaves of beach vitex revealed that S. caricae CMML20–2 and A. alternata (CMML20–7, CMML20–8, CMML20–9, and CMML20–10) caused disease lesions while the other species did not. The fungal species S. caricae, C. aenigma, and F. humuli are the first reported in the host worldwide, and S. caricae and F. humuli are first reported in Korea. In vitro fungicide sensitivity assays were carried out based on a measurement of diametrical mycelial growth on media amended with different doses of the fungicides fludioxonil, metconazole, and fluxapyroxad. Fungicide sensitivity varied significantly among the species, and the A. alternata and S. caricae isolates were more sensitive to fluxapyroxad than the other isolates. Our study contributes to the understanding of fungal diversity in forest mycology and demonstrates that pathogenic fungi including A. alternata and S. caricae might accelerate decline in leaf health.

Crop production has been substantially reduced by devastating fungal and oomycete pathogens, and these pathogens continue to threaten global food security. Although chemical and cultural controls have been used for crop protection, these involve continuous costs and time and fungicide resistance among plant pathogens has been increasingly reported. The most efficient way to protect crops from plant pathogens is cultivation of disease-resistant cultivars. However, traditional breeding approaches are laborious and time intensive. Recently, the CRISPR/Cas9 system has been utilized to enhance disease resistance among different crops such as rice, cacao, wheat, tomato, and grape. This system allows for precise genome editing of various organisms via RNA-guided DNA endonuclease activity. Beyond genome editing in crops, editing the genomes of fungal and oomycete pathogens can also provide new strategies for plant disease management. This review focuses on the recent studies of plant disease resistance against fungal and oomycete pathogens using the CRISPR/Cas9 system. For long-term plant disease management, the targeting of multiple plant disease resistance mechanisms with CRISPR/Cas9 and insights gained by probing fungal and oomycete genomes with this system will be powerful approaches.

In this paper, we propose a compact-standard antenna method (C-SAM) for antenna calibration above 1 GHz. The test-site evaluation of the fully-anechoic room (FAR) condition satisfied the free-space conditions. When the C-SAM was compared with conventional antenna calibration methods, the maximum deviation was within ±0.18 dB for the 1–18 GHz frequency range. Unlike the conventional antenna calibration methods, the proposed method is a simple standard antenna method that calculates the antenna factor of the antenna under calibration (AUC) with only one site insertion loss (SIL) measurement of an antenna calibration site that meets free-space conditions. Therefore, the C-SAM is the best candidate for antenna calibration owing to the method’s simplicity and cost-reduction potential.

Chuncheon, a medium-sized city in South Korea, frequently shows high PM2.5 concentrations despite scarce anthropogenic emission sources. To identify factors increasing PM2.5 concentrations, PM2.5 and its major chemical components were concurrently measured at two different sites, namely, downtown and suburban areas. The average PM2.5 concentrations at the two sites were similar, but the daily and monthly variations in PM2.5 and its components were significantly larger at the suburban site. NH4+ was significantly higher at the suburban site than at the downtown site, whereas organic carbon (OC) showed the opposite trend. Several PM2.5 samples showed an abrupt increase during winter at the suburban site, along with an increase in the amount of OC, NH4+, and K+, and the correlations between water-soluble OC, K+, and NH4+ were considerably strong, implying that local biomass burning in the suburban site was an important source of high PM2.5 episodes. Secondary OC (SOC) concentration was generally lower at the suburban site than at the downtown site, but its contribution to OC increased during winter with an increase in relative humidity, indicating the significance of heterogeneous SOC formation reactions at the suburban site. These results indicate that relevant local measures can be put into place to alleviate the occurrence of high PM2.5 concentration episodes even in medium-sized residential cities where medium-and long-range transport is anticipated to be significant.

Abstract Background Veterinary medicines have been widely used for the prevention and treatment of diseases, growth promotion, and to promote feeding efficacy in livestock. As the veterinary medicine industry has steadily grown, it is crucial to set up a baseline for the quality of medicine as well as the insufficiency or excessiveness of the active ingredients in drug products to ensure the compliance, safety and efficacy of these medicines. Thus, the 10 years data of post-marketing quality control study was summarized to determine the rate and extent of non-compliance of these medicines and to establish baseline data for future quality control measures of veterinary medicine. Results In this study, 1650 drugs for veterinary use were collected per year from each city and province in Korea and analysed for the quantity of active ingredients according to the “national post-market surveillance (NPMS) system” over the past decade. The NPMS assessment was performed using liquid and gas chromatography, titration, UV/Vis spectrophotometry, and bioassays. A total of 358 cases were deemed noncompliant, with the average noncompliance rate for all medicine types being 2.0%. The average noncompliance rates for antibiotics, biologics and other chemical drugs except antibiotics (OCD) were 1.1%, 1.2%, and 3.0%, respectively. The first leading cause for noncompliant products was insufficient quantity of major ingredients (283 cases), and the second leading cause was the existence of excess amount of active ingredients (60 cases). Tylosin, spiramycin, ampicillin, tetracyclines and penicillins were most frequently found to be noncompliant among antibiotics. Among the OCD, the noncompliance was found commonly in vitamin A. Conclusion The overall trend presented gradually decreasing violation rates, suggesting that the quality of veterinary medicines has improved. Consistent application of the NPMS assessment and the establishment of the Korea Veterinary Good Manufacturing Practice (KVGMP) will help to maintain the good quality of medicine.

In this study, the ionic and carbonaceous compounds in PM2.5 were analysed in the small residential city of Chuncheon, Korea. To identify the local sources that substantially influence PM2.5 concentrations, the samples were divided into two groups: samples with PM2.5 concentrations higher than those in the upwind metropolitan area (Seoul) and samples with lower PM2.5 concentrations. During the sampling period (December 2016–August 2018), the average PM2.5 was 23.2 μg m−3, which exceeds the annual national ambient air quality standard (15 μg m−3). When the PM2.5 concentrations were higher in Chuncheon than in Seoul, the organic carbon (OC) and elemental carbon (EC) concentrations increased the most among all the PM2.5 components measured in this study. This is attributable to secondary formation and biomass burning, because secondary OC was enhanced and water soluble OC was strongly correlated with K+, EC, and OC. A principal component analysis identified four factors contributing to PM2.5: fossil-fuel combustion, secondary inorganic and organic reactions in biomass burning plumes, crustal dust, and secondary NH4+ formation.

Poultry meat and eggs are vital sources of protein for human consumption worldwide. The use of several nutritional and medicinal products, including antibiotics, is crucial for efficient and safe poultry production. Accumulation of drug residues in meat and eggs from inappropriate drug use is a major concern to public health. Recently, enrofloxacin was detected (2.4–3.8 ppb) in edible eggs produced in Jeju Island, Korea. Although the farm from which the enrofloxacin-contaminated eggs were collected did not use enrofloxacin-containing products, they reported extensive use of a nutritional product (NPJ). Accordingly, in this study, we investigated whether enrofloxacin contamination had occurred accidentally in various widely used veterinary pharmaceutical products. Enrofloxacin content (4.57–179.08 ppm) in different lots of the NPJ was confirmed by liquid chromatography-tandem mass spectrometry (LC-MS/MS) analysis. Furthermore, 76 veterinary pharmaceutical products that are widely used in poultry farms in Korea and claim to not contain enrofloxacin were collected and analyzed by LC-MS/MS. Among them, a florfenicol product and a sulfatrimethoprime product were found to contain 3.00 and 0.57 ppm enrofloxacin, respectively. These results suggest that appropriate manufacturing standards are not being followed and that strict monitoring of drug manufacturing is necessary in Korea to avoid drug contamination.

Coronal Mass Ejections (CME), which originate from active regions of the Sun’s surface, e.g., sunspots, result in geomagnetic storms on Earth. The variation of the Earth’s geomagnetic field during such storms induces surface currents that could cause breakdowns in electricity power grids. Hence, it is essential to both monitor Geomagnetically Induced Currents (GICs) in real time and analyze previous GIC data. In 2012, in order to monitor the variation of GICs, the Korean Space Weather Center (KSWC) installed an induced current measurement system at SINGAPYEONG Substation, which is equipped with 765 kV extra-high-voltage transformers. Furthermore, in 2014, two induced current measurement systems were installed on the 345 kV high-voltage transformers at the MIGEUM and SINPOCHEON substations. This paper reports the installation process of the induced current measurement systems at these three substations. Furthermore, it presents the results of both an analysis performed using GIC data measured at the SINGAPYEONG Substation during periods of geomagnetic storms from July 2013 through April 2015 and the comparison between the obtained GIC data and magnetic field variation (dH/dt) data measured at the Icheon geomagnetic observatory.

High particulate matter (PM2.5) concentrations have been considered a serious environmental issue in South Korea. Recent studies have focused mostly on metropolitan and industrial cities; however, high PM2.5 episodes have also been frequently observed even in small– and middle-sized cities. Thus, in this study, PM2.5 and its major chemical components were measured in a small residential city with low anthropogenic emissions for 2 years to identify the factors affecting the PM2.5 concentrations. Overall, the average PM2.5 concentration was 29.4 μg m−3: about two times higher than the annual ambient air quality standard value. In winter, when the PM2.5 concentrations were generally higher, relative humidity (RH) was significantly correlated with both PM2.5 mass and the PM2.5/PM10 ratio, suggesting that high RH promoted the formation of secondary PM2.5. In addition, SO42−and NO3− were found to be correlated with both NH4+ and K+ in winter, indicating that biomass burning was an important source in this city. Water-soluble organic carbon (WSOC) was also highly correlated with elemental carbon (EC) and K+ in fall and winter, when the burning of agricultural residues actively occurred. During high concentration episodes, NO3− exhibited the highest increase; nevertheless, other components (e.g., K+ and organic carbon) also significantly increased.

Pathogenic Escherichia coli (E. coli)-associated infections are becoming difficult to treat because of the rapid emergence of antibiotic-resistant strains. Novel approaches are required to prevent the progression of resistance and to extend the lifespan of existing antibiotics. This study was designed to improve the effectiveness of traditional antibiotics against E. coli using a combination of the gallic acid (GA), hamamelitannin, epicatechin gallate, epigallocatechin, and epicatechin. The fractional inhibitory concentration index (FICI) of each of the phenolic compound-antibiotic combinations against E. coli was ascertained. Considering the clinical significance and FICI, two combinations (hamamelitannin-erythromycin and GA-ampicillin) were evaluated for their impact on certain virulence factors of E. coli. Finally, the effects of hamamelitannin and GA on Rattus norvegicus (IEC-6) cell viability were investigated. The FICIs of the antibacterial combinations against E. coli were 0.281–1.008. The GA-ampicillin and hamamelitannin-erythromycin combinations more effectively prohibited the growth, biofilm viability, and swim and swarm motilities of E. coli than individual antibiotics. The concentration of hamamelitannin and GA required to reduce viability by 50% (IC50) in IEC-6 cells was 988.54 μM and 564.55 μM, correspondingly. GA-ampicillin and hamamelitannin-erythromycin may be potent combinations and promising candidates for eradicating pathogenic E. coli in humans and animals.

Advanced metering infrastructure (AMI) refers to the electricity service infrastructure between electricity consumers and suppliers and is technically essential for the realization of a smart grid environment. To implement AMI, various communications technologies are being used based on the application environment according to the utility. However, using a single communications method can give rise to attenuation in the downtown underground distribution line section or cause higher supply costs due to decreased density in the range from farming to fishing areas. A hybrid AMI is one solution to this problem. According to an economic analysis of previous AMI deployment, the cost to install a communications network accounts on average for 45% of the total cost. Since the installation cost of a communications network is influenced by the density of the installation environment, a hybrid AMI, which allows the configuration of a flexible network using both wired and wireless communications, can be a good alternative, both technically and financially. This study conducted a simulation based on density of the installation environment and configuration of the communications network to analyze the economic effect of installing a hybrid AMI communications network. It assumed that a hybrid AMI was deployed in an overhead distribution line in a low-density area. The simulation outcomes were compared and analyzed against the power line communication (PLC)-only AMI method. The results showed that the hybrid AMI method had a 10% communications network cost reduction effect compared to the PLC-only AMI method. In addition, the analysis indicated that there was a maximum 19% cost reduction effect in communications network installation depending on the method of network installation, suggesting that the hybrid AMI was economically more effective than the PLC-only AMI method.