Search

The use of segmented HPGe detectors for gamma-ray tracking applications is well established. The spectroscopic capabilities of these detectors make them most suitable for such applications. For similar reasons, the use of such detectors in the tomographic measurement of irradiated nuclear fuel has also been envisioned. Especially, these detectors can facilitate faster fuel examination with excellent energy resolution. We have proposed and designed a novel planar segmented HPGe detector for use in gamma emission tomography. The design of the detector segmentation and the mode of operation is unique and offers six simultaneous detection channels for tomographic measurements. This work reports the first experimental evaluation of the performance of the detector. Important characteristics of the detector have been obtained, such as energy resolution of the segments in 1-fold (one segment) and 2-fold (two segments) modes, throughput curves, crosstalk energy corrections, and mislocalisation rate. Collimated source tests have been performed and the results have been compared with the MCNP simulations results. The obtained results are as expected and in good agreement with the simulation results, and it is estimated that using this detector can speed up the data collection by 3.2 times in comparison to an unsegmented detector of the same overall dimensions, in a tomographic application. Further improvements are foreseeable if scaling up to a larger detector with greater segmentation.

The JET neutron camera is a well-established detector system at JET, which has 19 sightlines each equipped with a liquid scintillator. The system measures a 2D profile of the neutron emission from the plasma. A first principle physics method is used to estimate the DD neutron yield that is based on JET neutron camera measurements and is independent of other neutron measurements. This paper details the data reduction techniques, models of the neutron camera, simulations of neutron transport, and detector responses used to this end. The estimate uses a simple parameterized model of the neutron emission profile. The method makes use of the JET neutron camera’s upgraded data acquisition system. It also accounts for neutron scattering near the detectors and transmission through the collimator. These components together contribute to 9% of the detected neutron rate above a 0.5 MeVee energy threshold. Despite the simplicity of the neutron emission profile model, the DD neutron yield estimate falls on average within 10% agreement with a corresponding estimate from the JET fission chambers. The method can be improved by considering more advanced neutron emission profiles. It can also be expanded to estimate the DT neutron yield with the same methodology.

Post-irradiation examination of nuclear fuel is routinely performed to characterize the important properties of the current and the future fuel. Gamma emission tomography is a proven non-invasive technique for this purpose. Among various measurement elements of the technique, a gamma-ray detector is an important element whose spectroscopic abilities and detection efficiency affect the overall results. Finding a combination of high detection efficiency and excellent energy resolution in a single detector is often a challenge. We have designed a novel planar segmented HPGe detector which offers simultaneous measurement in six lines of sight with excellent energy resolution. The simultaneous detection ability enables faster data acquisition in a tomographic measurement which may facilitate achieving higher spatial resolution. In this work, we have demonstrated the first use of the detector by performing a full tomographic measurement of mockup fuel rods. Two methods of detector data analysis were used to make spectra and the images (tomograms) were reconstructed using the filtered back projection algorithm. The reconstructed images validate the successful use of the detector for tomographic measurement. The use of the detector for real fuel measurement is being planned and will be performed in the near future., VR Bränslediagnostik - 113330190

Material test reactors have an extended use in irradiation testing of novel nuclear fuel materials and the fuel behavior in off-normal conditions. The performance of the nuclear fuel is examined in in-pile and out-of-pile post-irradiation examinations (PIEs), e.g., using Gamma Emission Tomography (GET). GET is a nondestructive assay that images the internal spatial distribution of gamma-emitting nuclides built up in the fuel due to irradiation. Since GET can be performed close to the reactor and without intrusion in the fuel object, it can potentially speed up the data generation from PIE in irradiation testing. The performance metrics of GET devices can be identified regarding time requirements, noise in the reconstructed image, signal-to-background ratio, and spatial resolution. However, these are complicated to determine, partly due to inherent trade-offs between the metrics themselves, partly because they depend on the fuel activity and its spectrum (i.e., object dependent), and, finally, on the GET setup and its configuration. This work proposes a structured methodology for optimizing the collimator design for a new generation of GET tomography setups, intending to improve spatial resolution by one order of magnitude: from the millimeter scale to the hundred-micron scale. The conflicting performance metrics are determined based on the controllable parameters of the GET setup and the uncontrollable parameters of an anticipated fuel object, able to provide a signal-to-background ratio above 100. The trade-off between the performance remaining metrics is then visualized by a Pareto approach, where dominated solutions are rejected. Finally, constraints on noise level and measurement time are used to find the optimal spatial resolution. Two GET setups are presented using the outlined method. Firstly, to upgrade the tomography test bench BETTAN at Uppsala University, a new segmented HPGe detector was planned to be tested using low-activity fuel rod mock-ups. Second

The majority of the energy in a nuclear explosion is released in the immediate blast and the initial radiation accounts. The remaining fraction is released through radioactive decay of the explosion's fission products and neutron activation products over a longer time span. This allows for the detection of a nuclear explosion by detecting the presence of residual decay. Radionuclide monitoring stations for detection of radioactive emissions to the atmosphere is thereby an important tool in the verification of compliance with nuclear disarmament treaties. In particular, the globally spanning radionuclide station network of the International Monitoring System (IMS) has been implemented for verification of the Comprehensive Nuclear-Test-Ban Treaty. High Purity Germanium (HPGe) detectors are workhorses in radionuclide monitoring. The detection of characteristic gamma rays can be used to disclose the presence of signature nuclides produced innuclear weapon tests. A particular development that has potential to improve the sensitivity of radionuclide monitoring is the coincidence technique where decaying nuclides that emit several coincident gamma rays can be detected at much smaller activity concentrations than with conventional gamma spectroscopy. In this project, dedicated gamma-gamma coincidence detectors are being developed, utilizing electronically segmented HPGe detectors. These detectors are expected to be highly sensitive to low-activity samples of nuclides that present coincident emissions of gamma rays. In this paper we present the concept, define performance parameters, and explore the performance of such detectors to a subset of radionuclides of particular CTBT relevance. In addition, we discuss the path forward in developing a next generation gamma-gamma coincidence spectroscopy system of segmented HPGe.

We have proposed a planar electronically segmented HPGe detector concept in combination with a multi-slit collimator for gamma emission tomography. In this work, the spatial resolution achievable by using the collimated segmented HPGe detector was evaluated, prior to the manufacture and operation of the detector. The spatial response of a collimated segmented HPGe detector concept was evaluated using simulations performed with Monte Carlo N-Particle transport code MCNP6. The full detector and multi-slit collimator system were modeled and for the quantification of the spatial response, the Modulation Transfer Function (MTF) was chosen as a performance metric. The MTF curve was obtained through the calculation of the Line Spread Function (LSF) by analyzing simulated projection data. In addition, tomographic reconstructions of the simulated simplified test objects were made to demonstrate the performance of the segmented HPGe detector in the planned application. For 662 keV photons, the spatial resolution obtained was approximately the same as the collimator slit width for both 100 and 150 mm long collimators. The corresponding spatial resolution at 1596 keV photon energy was almost twice the slit width for 100 mm collimator, due to the partial penetration of the high-energy gamma rays through the collimator bulk. For a 150 mm long collimator, an improved resolution was obtained., VR Bränslediagnostik

Gamma-ray spectrometry using collimated detectors is a well-established examination method for irradiated nuclear fuel. However, the feasibility of examining a particular nuclide of interest is subject to constraints; the peak must be statistically determinable with the desired precision and the total spectrum count rate in the detector should not cause throughput issues. Methods were assembled for gamma spectrum prediction to optimize instruments for gamma emission tomography and to enable a priori feasibility evaluation of determination of single peaks of irradiated nuclear fuel. The aim was to find reliable results (~10% accuracy) regarding total spectrum and peak count rates with faster computation time than a full-Monte Carlo approach. For this purpose, the method is based on depletion calculations with SERPENT2, a point-source kernel method for the collimator response, a rig response matrix and a detector response matrix, both computed with MCNP6. The computational methodology uses as input the fuel properties (dimensions, materials, power history, and cooling time), and the instrumental setup (collimator and detector dimensions and materials). The prediction method was validated using measured data from a high-burnup, short-cooled test fuel rodlet from the Halden reactor. Absolute count rates and ratios of characteristic peaks were compared between predicted and measured spectra, showing a total count rate overestimation of 7% and discrepancies between 2-20% for the single peaks (same order of magnitude of the uncertainty). This level of agreement is deemed sufficient for measurement campaigns planning, and the optimization of spectroscopic instruments for use in gamma scanning and tomography of nuclear fuel.

Engaging mass audiences with crucial societal issues, such as cli-mate change, can be provided through interactive exhibits designed around the paradigm of exploranation. We present example inter-active installations in the newly founded Wadstr¨oms Exploranation Laboratory that explain various aspects of climate change while allowing public participants to explore the real scientific data. We describe how effects and causes of climate change can be communi-cated by two of the installations that allow for interactive opportuni-ties to explore the underlying data while gaining insight into climate change sources and effects. We close with implications for future work on exploranation as an emerging visualization pedagogy in public spaces.

In a Swedish citizen science project, more than 200 elementary school classes participated in collecting fungi, soil samples, and droppings from deer and wild boar, from all over Sweden. The samples have been sent to a laboratory at Uppsala University where they are being analyzed through gamma spectroscopy with a shielded HPGe detector. The main objective is to scan the samples for 137Cs from the Chernobyl accident and compare the data with measurements from 1986, but uptake of naturally occuring radionuclides like 40K and radon daughters will also be determined. Together with the soil samples, transfer factors will be derived, and correlations for these factors will be sought for different species of fungi and soil types. The potential for correlating the results with different biological processes will also be investigated, in part through the collected animal droppings. This is a work in progress where the present status of the experimental setup and methodology are presented. Issues with the initial approach for corrections are discussed and preliminary results are presented.

A growing trend in science is that research institutions reach out to members of the public for participating in research. The reasons for outreach are many, spanning from the desire to collect and/or analyse large sets of data efficiently, to the idea of including the general public on a very fundamental level in science-making and ultimately decision-making. The presented project is curriculum-based and carried out in 240 lower secondary school classes (pupils of age 13-16). The task, as designed by the participating universities, is to collect mushrooms, soil and animal droppings from different parts of Sweden, do preliminary sample preparation and analyses and send the samples to the university institutions for radioactivity measurement. Behind the project is a desire to compare today’s levels of 137Cs with those deposited right after the Chernobyl accident in 1986, but also to study the exchange of caesium between organisms as well as the impacts of biological and geological processes on uptake and retention. The scientific outcome is a geodatabase with the 137Cs activity (Bq/m2) present in the Swedish environment, where radioactivity data can be linked to the species (fungi, competing species, animals foraging), forest type, land type, land use and other environmental factors. The science question is of interest to the general public as foraging for mushrooms, as well as spending recreational time in forests is widely popular in Sweden. In this article, we will discuss the current status of the project and the observations we have made about how well the public can participate in scientific research. Focus will be on organization of the project, such as logistics, preparation of supportive material, feedback and communication between researchers and schools. We will present observations about the impact the project has had on the participants, based on quantitative and qualitative evaluations.

An important instrumental development work has been done in the last two decades in the field of neutron and gamma ray spectroscopic measurements of magnetic confinement plasmas. Starting from the present state of the art instrumentation installed at JET, this paper reviews the recent development that has been carried out within the EUROFUSION programme for the forthcoming high power JET D and DT campaign. This development was dedicated to the realization of new compact neutron and gamma-ray spectrometers which combine very high energy resolution (typically better than 5%) and MHz counting rate capabilities allowing for time resolution in the 10 ms time scale. One of the advantages offered by the compact dimensions of these spectrometers is to make possible their use in multiple sight-line camera configurations, such as for future burning plasma reactors (ITER and DEMO). New compact neutron spectrometers based on single crystal diamond detectors have been developed and installed at JET for measurements of the 14MeV neutron spectrum. Measurements on a portable DT neutron generator have shown that neutron spectroscopy of the accelerated beam ions at unprecedented energy resolution (similar to 1% at 14 MeV) is possible, which opens up new opportunities for diagnosing DT plasmas. For what concerns gamma ray measurements, the JET gamma ray camera has been recently upgraded with new compact spectrometers based on a LaBr3 scintillator coupled to Silicon Photomultiplier with the dual aim to improve the spectroscopic and rate capabilities of the detectors. The upgrade camera system will reconstruct the spatial gamma ray emissivity from the plasma in the MeV energy range at MHz counting rates and energy resolution in the 2-4% range. This will allow physics studies of gamma rays produced by the interaction of fast ions with impurities in the plasma and bremsstrahlung emission from runaway electrons.

The complexity of todays visualization applications demands specific visualization systems tailored for the development of these applications. Frequently, such systems utilize levels of abstraction to improve the application development process, for insta, Funding agencies: Swedish e-Science Research Centre (SeRC); Deutsche Forschungsgemeinschaft (DFG)German Research Foundation (DFG) [RO3408/3-1]; ExcellenceCenter at Linkoping and Lund in Information Technology (ELLIIT); Knut and Alice Wallenberg Foundation (KAW)Knut & Alice

VR Bränslediagnostik-113 330 190

Selected set of samples from JET ITER-Like Wall (JET-ILW) divertor tiles exposed both in 2013-2014 and 2011-2014 has been analysed using Thermal Desorption Spectrometry (TDS). The deuterium (D) amounts obtained with TDS were compared with Ion Beam Analysis (IBA) and Secondary Ion Mass Spectrometry (SIMS) data. The highest amount of D was found on the top part of inner divertor which has regions with the thickest deposited layers. This area resides deep in the scrape-off layer. Changes in plasma configurations between the first (2011-2012) and the second (2013-2014) JET-ILW campaign altered the material migration towards the inner and the outer divertor corner increasing the amount of deposition in the shadowed areas of the divertor base tiles. D retention on the outer divertor tiles is clearly smaller than on the inner divertor tiles. Experimental TDS spectra for samples from the top part of inner divertor and from the outer strike point region were modelled using TMAP program. Experimental deuterium profiles obtained with SIMS have been used and the detrapping and the activation energies have been adjusted. Analysis of the results of the TMAP simulations enabled to determine the nature of traps in different samples., For complete list of authors see http://dx.doi.org/10.1016/j.nme.2019.02.031

Preliminary results investigating the microstructure, bonding and effect of beryllium oxide formation on retention in the JET ITER-like wall beryllium tiles, are presented. The tiles have been investigated by several techniques: Scanning Electron Microscopy (SEM) equipped with Energy Dispersive X-ray (EDX), Transmission Electron microscopy (TEM) equipped with EDX and Electron Energy Loss Spectroscopy (EELS), Raman Spectroscopy and Thermal Desorption Spectroscopy (TDS). This paper focuses on results from melted materials of the dump plate tiles in JET. From our results and the literature, it is concluded, beryllium can form micron deep oxide islands contrary to the nanometric oxides predicted under vacuum conditions. The deepest oxides analyzed were up to 2-micron thicknesses. The beryllium Deuteroxide (BeOxDy) bond was found with Raman Spectroscopy. Application of EELS confirmed the oxide presence and stoichiometry. Literature suggests these oxides form at temperatures greater than 700 degrees C where self-diffusion of beryllium ions through the surface oxide layer can occur. Further oxidation is made possible between oxygen plasma impurities and the beryllium ions now present at the wall surface. Under Ultra High Vacuum (UHV) nanometric Beryllium oxide layers are formed and passivate at room temperature. After continual cyclic heating (to the point of melt formation) in the presence of oxygen impurities from the plasma, oxide growth to the levels seen experimentally (approximately two microns) is proposed. This retention mechanism is not considered to contribute dramatically to overall retention in JET, due to low levels of melt formation. However, this mechanism, thought the result of operation environment and melt formation, could be of wider concern to ITER, dependent on wall temperatures., For complete list of authors see http://dx.doi.org/10.1016/j.nme.2019.02.022

In this study, beryllium tiles from Joint European Torus (JET) vacuum vessel wall were analysed and compared regarding their position in the vacuum vessel and differences in the exploitation conditions during two campaigns of ITER-Like-Wall (ILW) in 2011-2012 (ILW1) and 2013-2014 (ILW2) Tritium content in beryllium samples were assessed. Two methods were used to measure tritium content in the samples - dissolution under controlled conditions and tritium thermal desorption. Prior to desorption and dissolution experiments, scanning electron microscopy and energy dispersive x-ray spectroscopy were used to study structure and chemical composition of plasma-facing-surfaces of the beryllium samples. Experimental results revealed that tritium content in the samples is in range of 2.10(11)-2.10(13) tritium atoms per square centimetre of the surface area with its highest content in the samples from the outer wall of the vacuum vessel (up to 1.9.10(13) atoms/cm(2) in ILW1 campaign and 2.4.10(13) atoms/cm(2) in ILW2). The lowest content of tritium was found in the upper part of the vacuum vessel (2.0.10(12) atoms/cm(2) and 2.0.10(11) atoms/cm(2) in ILW1 and ILW2, respectively). Results obtained from scanning electron microscopy has shown that surface morphology is different within single tile, however if to compare two campaigns main tendencies remains similar., For complete list of authors see http://dx.doi.org/10.1016/j.nme.2019.02.011

Waves in the Ion Cyclotron Range of Frequencies (ICRF) enhance local Plasma-Surface Interactions (PSI) near the wave launchers and magnetically-connected objects via Radio-Frequency (RF) sheath rectification. ITER will use 20MW of ICRF power over long pulses, questioning the long-term impact of RF-enhanced localized erosion on the lifetime of its Beryllium (Be) wall. Recent dedicated ICRF-heated L-mode discharges documented this process on JET for different types of ICRF antennas. Using visible spectroscopy in JET ICRF-heated L-mode discharges, poloidally-localized regions of enhanced (by similar to 2-4x) Be I and Be II light emission were observed on two outboard limiters magnetically connected to the bottom of the active ITER-Like Antenna (ILA). The observed RF-PSI induced by the ILA was qualitatively comparable to that induced by the JET standard, type-A2 antennas, for similar strap toroidal phasing and connection geometries. The Be II line emission was found more intense when powering the bottom half of the ILA rather than its top half. Conversely, more pronounced SOL density modifications were observed with only top array operation, on field lines connected to the top half of the ILA. So far the near-field modeling of the ILA with antenna code TOPICA (Torino Polytechnic Ion Cyclotron Antenna), using curved antenna model, was partially able to reproduce qualitatively the observed phenomena. A quantitative discrepancy persisted between the observed Be source amplification and the calculated, corresponding increases in E-// field at the magnetically connected locations to the ILA when changing from only top to only bottom half antenna operation. This paper revisits these current drive phased and half-ILA powered cases using for the new simulations flat model of the ILA and more realistic antenna feeding to calculate the E-// field maps with TOPICA code. Further, the Self-consistent Sheaths and Waves for Ion Cyclotron Heating Slow Wave (SSWICH-SW) code, which coupl, For complete list of authors see http://dx.doi.org/10.1016/j.nme.2019.03.009

ERO is a 3D Monte-Carlo impurity transport and plasma-surface interaction code. In 2011 it was applied for the ITER first wall (FW) life time predictions [1] (critical blanket module BM11). After that the same code was significantly improved during its application to existing fusion-relevant plasma devices: the tokamak JET equipped with an ITER-like wall and linear plasma device PISCES-B. This has allowed testing the sputtering data for beryllium (Be) and showing that the "ERO-min" fit based on the large (50%) deuterium (D) surface content is well suitable for plasma-wetted areas (D plasma). The improved procedure for calculating of the effective sputtering yields for each location along the plasma-facing surface using the recently developed semi-analytical sheath approach was validated. The re-evaluation of the effective yields for BM11 following the similar revisit of the JET data has indicated significant increase of erosion and motivated the current re-visit of ERO simulations., For complete list of authors see http://dx.doi.org/10.1016/j.nme.2019.03.016

In some JET discharges, type-I edge localised modes (ELMs) are preceded by a class of low-frequency oscillations (Perez et al 2004 Nucl. Fusion 44 609). While in many cases the ELM is triggered during the growth phase of this oscillation, it is also observed that this type of oscillation can saturate and last for several tens of ms until an ELM occurs. In order to identify the nature of these modes, a wide pre-ELM oscillation database, including detailed pedestal profile information, has been assembled and analysed in terms of MHD stability parameters. The existence domain of these pre-ELM oscillations and the statistical distribution of toroidal mode numbers (n) up to n = 16 have been mapped in ballooning alpha (alpha(ball)) and either edge current density (J(edge)) or pedestal collisionality (nu(ee,ped)*) coordinates and compared to linear MHD stability predictions. The pre-ELM oscillations are reliably observed when the J/alpha ratio is high enough for the pedestal to access the coupled peeling-ballooning (PB) domain (aka stability nose). Conversely, when the pedestal is found to be in or near the high-n ballooning domain (which is at low J/alpha ratio), ELMs are usually triggered promptly, i.e. with no detectable pre-ELM oscillations, or with pre-ELM oscillations only observable on ECE whose n appears to be too high to be resolved by the magnetics. Individual discharges can sometimes exhibit a fairly wide range of pre-ELM mode numbers, but for a wider database, the statistical n-number domains are found to be well ordered along the J - alpha stability boundary and behave as expected from PB theory: the higher the J/alpha ratio, the lower the mode's measured n tends to be. Within the measurement uncertainties, the measured n is usually found to be compatible with the most unstable n predicted by the linear stability code MISHKA1. These results confirm the earlier hypothesis that these modes are coupled peeling-ballooning modes, and extend and generalise to higher, For complete list of authors see http://dx.doi.org/10.1088/1741-4326/ab0031

The analysis of the polarimetry measurements has the aim of validating models (De Marco and Segre 1972 Plasma Phys. 14 245), with a careful attention to the clarification of their limits of application. In this paper a new approximation method is introduced, the so-called special constant Omega direction (SCOD), which gives an analytical solution to the polarimetry exact Stokes model equations. The available approximate solutions (including SCOD) of the polarimetry propagation equations are presented, compared and their application limits determined, using a reference tokamak configuration, which is a simplified equilibrium for a circular tokamak. The SCOD approximation is compared successfully to the Stokes model in the context also of equilibria evaluated for two JET discharges. The approximation methods are analytical or very simple mathematical expressions which can also be used in equilibrium codes for their optimization., For complete list of authors see http://dx.doi.org/10.1088/1361-6587/ab09c2

Two high performance JET-ILW pulses, pertaining to the 2016 experimental campaign, have been numerically simulated with the self-consistent code COREDIV with the aim of predicting the ELM-averaged power load to the target when extrapolated to DT plasmas. The input power of about 33 MW as well as the total radiated power and the average density are similar in the two pulses, but for one of them the density is provided by combined low gas puff and pellet injection, characterized by low SOL density, for the other one by gas fuelling only, at higher SOT. density. Considering the magnetic configuration of theses pulses and the presence of a significant amount of Ni (not included in the version of the code used for these simulations), a number of assumptions are made in order to reproduce numerically the main core and SOL experimental data. The extrapolation to DT plasmas at the original input power of 33 MW, and taking into account only the thermal component of the alpha-power, does not show any significant difference regarding the power to the target with respect to the DD case. In contrast, the simulations at auxiliary power 40 MW, both at the original I-p = 3 MA and at I-p = 4 MA, show that the power to the target for both pulses is possibly too high to be sustained for about 5 s by strike-point sweeping alone without any control by Ne seeding. Even though the target power load may decrease to about 13-15 MW with substantial Ne seeding for both pulses, as from numerical predictions, there are indications suggesting that the control of the power load may be more critical for the pulse with pellet injection, due to the reduced SOL radiation., For complete list of authors see http://dx.doi.org/10.1088/1741-4326/ab0c47

An extension of the SolEdge2D-EIRENE code package, named D-WEE, has been developed to add the dynamics of thermal desorption of hydrogen isotopes from the surface of plasma facing materials. To achieve this purpose, D-WEE models hydrogen isotopes implantation, transport and retention in those materials. Before launching autoconsistent simulation (with feedback of D-WEE on SolEdge2D-EIRENE), D-WEE has to be initialised to ensure a realistic wall behaviour in terms of dynamics (pumping or fuelling areas) and fuel content. A methodology based on modelling is introduced to perform such initialisation. A synthetic plasma pulse is built from consecutive SolEdge2D-EIRENE simulations. This synthetic pulse is used as a plasma background for the D-WEE module. A sequence of plasma pulses is simulated with D-WEE to model a tokamak operation. This simulation enables to extract at a desired time during a pulse the local fuel inventory and the local desorption flux density which could be used as initial condition for coupled plasma-wall simulations. To assess the relevance of the dynamic retention behaviour obtained in the simulation, a confrontation to post-pulse experimental pressure measurement is performed. Such confrontation reveals a qualitative agreement between the temporal pressure drop obtained in the simulation and the one observed experimentally. The simulated dynamic retention during the consecutive pulses is also studied., For complete list of authors see http://dx.doi.org/10.1016/j.nme.2019.03.019

Effect of ELMs on fuel retention at the bulk W target of JET ITER-Like Wall was studied with multi-scale calculations. Plasma input parameters were taken from ELMy H-mode plasma experiment. The energetic intra-ELM fuel particles get implanted and create near-surface defects up to depths of few tens of nm, which act as the main fuel trapping sites during ELMs. Clustering of implantation-induced vacancies were found to take place. The incoming flux of inter-ELM plasma particles increases the different filling levels of trapped fuel in defects. The temperature increase of the W target during the pulse increases the fuel detrapping rate. The inter-ELM fuel particle flux refills the partially emptied trapping sites and fills new sites. This leads to a competing effect on the retention and release rates of the implanted particles. At high temperatures the main retention appeared in larger vacancy clusters due to increased clustering rate., For complete list of authors see http://dx.doi.org/10.1016/j.nme.2019.03.013

A power-balance model, with radiation losses from impurities and neutrals, gives a unified description of the density limit (DL) of the stellarator, the L-mode tokamak, and the reversed field pinch (RFP). The model predicts a Sudo-like scaling for the stellarator, a Greenwald- like scaling, alpha I-p(8/9), for the RFP and the ohmic tokamak, a mixed scaling, alpha (PIp4/9)-I-4/9, for the additionally heated L-mode tokamak. In a previous paper (Zanca et al 2017 Nucl. Fusion 57 056010) the model was compared with ohmic tokamak, RFP and stellarator experiments. Here, we address the issue of the DL dependence on heating power in the L-mode tokamak. Experimental data from high-density disrupted L-mode discharges performed at JET, as well as in other machines, arc taken as a term of comparison. The model fits the observed maximum densities better than the pure Greenwald limit., For complete list of authors see http://dx.doi.org/10.1088/1741-4326/ab3b31

This paper outlines an approach towards improved rigour in tokamak turbulence transport model validation within integrated modelling. Gaussian process regression (GPR) techniques were applied for profile fitting during the preparation of integrated modelling simulations allowing for rigourous sensitivity tests of prescribed initial and boundary conditions as both fit and derivative uncertainties are provided. This was demonstrated by a JETTO integrated modelling simulation of the JET ITER-like-wall H-mode baseline discharge #92436 with the QuaLiKiz quasilinear turbulent transport model, which is the subject of extrapolation towards a deuterium-tritium plasma. The simulation simultaneously evaluates the time evolution of heat, particle, and momentum fluxes over similar to 10 confinement times, with a simulation boundary condition at rho(tor) = 0.85. Routine inclusion of momentum transport prediction in multi-channel flux-driven transport modelling is not standard and is facilitated here by recent developments within the QuaLiKiz model. Excellent agreement was achieved between the fitted and simulated profiles for n(e), T-e, T-i, and Omega(tor) within 2 sigma, but the simulation underpredicts the mid-radius Ti and overpredicts the core n(e) and T-e profiles for this discharge. Despite this, it was shown that this approach is capable of deriving reasonable inputs, including derivative quantities, to tokamak models from experimental data. Furthermore, multiple figures-of-merit were defined to quantitatively assess the agreement of integrated modelling predictions to experimental data within the GPR profile fitting framework., For complete list of authors see http://dx.doi.org/10.1088/1741-4326/ab065a

In this paper, we analyze heat transport in the JET tokamak using data from its high resolution ECE diagnostic and analyses based on the transfer entropy (TE). The analysis reveals that heat transport is not smooth and continuous, but is characterized by 'trapping regions' separated by `minor transport barriers'. Meat may 'jump over' these barriers and when the heating power is raised, this 'jumping' behavior becomes more prominent. To check that our results are relevant for global heat transport, we deduced an effective diffusion coefficient from the TE results. Both its value and overall radial variation are consistent with heat diffusivities reported in literature. The detailed radial structure of the effective diffusion coefficient was shown to be linked to the mentioned minor transport barriers., For complete list of authors see http://dx.doi.org/10.1088/1741-4326/ab03e1

Selected set of samples from JET ITER-Like Wall (JET-ILW) divertor tiles exposed in 2015-2016 has been analysed using Thermal Desorption Spectrometry (TDS). The deuterium (D) amounts obtained with TDS were compared with Nuclear Reaction Analysis (NRA). The highest amount of D was found on the top part of inner divertor which has regions with the thickest deposited layers as for divertor tiles removed in 2014. This area resides deep in the scrape-off layer and plasma configurations for the second (ILW-2, 2013-2014) and the third (ILW-3, 2015-2016) JET-ILW campaigns were similar. Agreement between TDS and NRA is good on the apron of Tile 1 and on the upper vertical region whereas on the lower vertical region of Tile 1 the NRA results are clearly smaller than the TDS results. Inner divertor Tile 3 has somewhat less D than Tiles 0 and 1, and the D amount decreases towards the lower part of the tile. The D retention at the divertor inner and outer corner regions is not symmetric as there is more D retention poloidally at the inner than at the outer divertor corner. In most cases the TDS spectra for the ILW-3 samples are different from the corresponding ILW-2 spectra because HD and D-2 release occurs at higher temperatures than from the ILW-2 samples indicating that the low energy traps have been emptied during the plasma operations and that D is either in the energetically deep traps or located deeper in the sample., For complete list of authors see http://dx.doi.org/10.1016/j.nme.2019.03.012

Post mortem analysis shows that mid and high atomic number metallic impurities are present in deposits on JET plasma facing components with the highest amount of Ni and W, and therefore the largest sink, being found at the top of the inner divertor. Sources are defined as "continuous" or "specific", in that "continuous" sources arise from ongoing erosion from plasma facing surfaces and "specific" are linked with specific events which decrease over time until they no longer act as a source. This contribution evaluates the sinks and estimates sources, and the balance gives an indication of the dominating processes. Charge exchange neutral erosion is found to be the main source of nickel, whereas erosion of divertor plasma facing components is the main source of tungsten. Specific sources are shown to have little influence over the global mid- and high-Z impurity concentrations in deposits., For complete list of authors see http://dx.doi.org/10.1016/j.nme.2018.12.024