Search

Objectives: To evaluate the effects of enhanced personal protective equipment (Enhanced_PPE) on student‐operator's experience and restorative procedure. Methods: Student‐operators (N = 29 Year 3 dental students) performed Class II composite restorations (SimpliShade, Kerr) in typodont upper molars (OneDental) equipped with N95 respirators, full‐face shields, disposable headwear and gowns (Enhanced_PPE) or surgical masks, protective glasses/goggles and non‐disposable gowns (Standard_PPE) 2 weeks later. Cavity dimensions were measured on cone beam computed tomography images. The quality of composite restorations was assessed using selected FDI criteria and Vickers hardness. A questionnaire assessed the operators' discomfort, anxiety, confidence, ability to perform, and procedure outcome. Data were analyzed using paired t‐test and McNemar test (alpha = 0.05). Results: Student‐operators experienced greater discomfort and anxiety, reduced confidence and ability to perform, and rated the procedure as less satisfactory with Enhanced_PPE (p < 0.05). Differences in proximal box width were marginally significant (Enhanced_PPE 1.8 ± 0.4 mm, Standard_PPE 1.6 ± 0.3 mm) (p = 0.047). Other cavity dimensions were similar between groups (p > 0.05) as were restorations regarding surface luster, anatomical form, marginal adaptation, proximal contour, and contact (p > 0.05). There were no differences in the hardness of composite restorations (top p = 0.349, bottom p = 0.334). Conclusions: Enhanced_PPE led to student‐operator discomfort, anxiety, and reduced confidence, but did not impact the quality of Class II preparation and composite restorations versus Standard_PPE. [ABSTRACT FROM AUTHOR]

Not fully maturated immune system in preterm neonates may contribute to the increased susceptibility to infection. The levels of some cytokines can be useful in the prediction and diagnosis of sepsis in premature neonates. In the present study, we evaluated the potential predictive role of IFN-γ and IL-5 in cord and venous blood, together with the determination of C-reactive protein and procalcitonin (PCT) for sepsis development in premature neonates. A total of 80 participants were included. The laboratory results and clinical histories showed that 21 participants had sepsis. Early onset sepsis was detected in 3 patients while late onset sepsis was observed in 18 participants. The venous plasma levels of IFN-γ and PCT was markedly increased in sepsis groups when compared to the participants without sepsis. On the other hand, levels of IL-5 did not significantly change in the evaluated groups of sepsis and in the control group of participants. Simultaneously, plasma venous levels were not altered in any of the evaluated groups. Obtained findings suggest that venous plasma levels of IFN-γ, rather than levels of IFN-γ in cord blood plasma, and PCT may have predictive potential for sepsis development in preterm neonates. Further studies are necessary to get more comprehension of the complex function of cytokines for sepsis development in preterm neonates.

Objective: To measure degree of conversion (DC) of a flowable composite, microtensile bond strength (MTBS) to dentine in the snow‐plow technique with/without preheating and temperature in the preheated composite. Materials and Methods: For DC, snow‐plow specimens of Filtek Ultimate Flowable (Flow) and Filtek Bulk Fill (Bulk) (3M) were prepared by light‐curing composites simultaneously in standardized molds while in control groups light‐curing was separate. DC of Flow was measured using micro‐Raman spectroscopy. For MTBS, specimens were prepared on dentine of human extracted molars by simultaneous (snow‐plow) or separate (control) light‐curing. MTBS was measured using a universal testing machine after 24 h and 6 months. Data were analyzed using ANOVA with Tukey's post hoc (α = 0.05). Results: Increased curing time significantly increased DC in snow‐plow from 13.4% ± 11.6% (10 s) to 31.8% ± 4.4% (40 s) albeit significantly lower than controls (p < 0.05). Preheated Bulk improved conversion in snow‐plow (44.3% ± 1.7%) and control (50.5% ± 2.6%) (p < 0.05). No significant differences occurred in MTBS between groups (p > 0.05). MTBS values ranged between 66.7 ± 8.4 MPa (snow‐plow group_21°C_baseline) and 54.1 ± 15.8 MPa (control_21°C_long‐term). Temperature in the preheated Bulk dropped to ~38°C after 30 s. Conclusions: Snow‐plow technique, irrespective of preheating, resulted in lower DC of Flow than separate light‐curing of composite increments. Snow‐plow, irrespective of preheating, resulted in similar initial and long‐term MTBS to dentine. Clinical Significance: Clinicians with preference for flowable composite liners in Class II restorations should be aware that the snow‐plow technique of simultaneous light‐curing of flowable and bulk‐fill composite increments affects monomer‐to‐polymer conversion, albeit no effect on immediate, and long‐term bonding to dentine was detected. Preheating sculptable bulk‐fill composite improves conversion of the flowable liner in the snow‐plow technique but has no detectable effect on bond strength to dentine. [ABSTRACT FROM AUTHOR]

The objective of this study was to measure temperature changes in the pulp chamber induced by polymerization of resin-based dental restoratives following a simulated procedure of direct pulp capping. Class I cavities with a microperforation at the pulp horn were prepared in extracted human molar teeth. The complete procedure of direct pulp capping and cavity restoration was performed with the root part of extracted teeth fixed in a water bath at 37 °C. Mineral trioxide aggregate, bioactive dentin substitute or calcium-hydroxide paste were used as pulp capping materials. Cavities were restored with a light-cured or chemically-cured resin-modified glass ionomer, universal adhesive and a bulk-fill composite, cured with a high-intensity LED unit. Pulp capping materials caused a slight temperature decrease. Lower temperature increase was recorded during light-curing of the glass ionomer liner after direct capping with mineral trioxide aggregate and calcium-hydroxide than that recorded for the bioactive dentin substitute. Adhesive light-curing increased temperature in all groups with higher mean temperatures in groups with chemically-cured as compared to those for the light-cured glass ionomer liner. Direct pulp capping with mineral trioxide aggregate or calcium-hydroxide followed by the light-cured resin-modified glass ionomer liner and a bonded bulk-fill composite restoration induced temperature changes below the potentially adverse threshold of 42.5°C. [Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. ON172007]