Search

This study investigates the strain rate-dependent deformation behavior of cost-effective twinning-induced plasticity (TWIP) steel, Fe–26Mn-0.4C, at 15 K and reveals intriguing insights into its mechanical properties. The serration type changes from type A to type C with decreasing strain rate, resulting in a quasi-cleavage fracture at the crack initiation site. Microstructural analysis unveils a correlation between strain rate and the evolution of bundle twins, nano-twins, and ε-martensites. These denser networks of deformation twins (DTs) and ε-martensites contribute to impacting the mechanical properties. The mechanism behind the formation of serrations involves a rate-dependent thermal instability effect and the intricate interactions between dislocations and dislocations/Mn–C couples. The distinct findings enhance our understanding of the complex deformation behavior of high-Mn steel at cryogenic temperatures and provide valuable insights into the broader field of high-Mn steel applications in dynamic environments.

This study investigates the mechanical properties of a friction-stir-welded (FSW) AA6061-T6 aluminum alloy at ultra-low temperature (ULT) of 20 K. In-situ neutron diffraction and orientation imaging microscopy were employed to compare the tensile deformation behavior of the base metal (BM) and heat-affected zone (HAZ) in the FSW aluminum plate. The results demonstrate that compared to room-temperature (RT), ULT induces a significant improvement in tensile strength and ductility in both the BM and HAZ. The enhanced mechanical properties in BM at ULT result from a more homogeneous deformation than occurs at RT. On the other hand, HAZ at ULT exhibits an even lower yield strength than at RT, but the strain hardening rate (SHR) is the most significant among the alloys, leading to a tensile strength of 346 MPa and the highest ductility of 46.8%. The lowest yield strength corresponds to the lowest-hardness zones in HAZ, caused by dissolved/coarsened precipitates during the FSW process. The highest SHR in HAZ at ULT is attributed to the hardening of the {111} grain families and finer dislocation cell structures. The dislocation densities of both the BM and HAZ increased considerably during tensile deformation at ULT, which accounts for the improvement in tensile strength. Revealing the mechanism behind the remarkable improvement in the mechanical properties of FSW AA6061-T6 at ULT suggests its applicability for cryogenic applications.

This study investigates the influence of CaO (0.5, 1 (wt.%)) alloying on the microstructural evolution, texture development and deformation behavior of AZ61 magnesium alloy. The uniaxial tension tests at room (RT) and cryogenic (CT, -150 °C) temperature were performed to investigate the twinability and dislocation behavior and its consequent effect on flow stress, ductility and strain hardening rate. The results showed that the AZ61-1CaO exhibited superior strength/ductility synergy at RT with a yield strength (YS) of 223 MPa and a ductility of 23% as compared to AZ61 (178 MPa, 18.5%) and AZ61-0.5CaO (198 MPa, 21%). Similar trend was witnessed for all the samples during CT deformation, where increase in the YS and decrease in ductility were observed. The Mtex tools based in-grain misorientation axis (IGMA) analysis of RT deformed samples revealed the higher activities of prismatic slip in AZ61-CaO, which led to superior ductility. Moreover, subsequent EBSD analysis of CT deformed samples showed the increased fraction of fine {10-12} tension twins and nucleation of multiple {10-12} twin variants caused by higher local stress concentration at the grain boundaries, which imposed the strengthening by twin-twin interaction. Lastly, the detailed investigations on strengthening contributors showed that the dislocation strengthening has the highest contribution towards strength in all samples.

Bimodal reinforcement consisting of powders of large graphite flake (GF) and small graphene nanoplatelet (GNP) were used to fabricate (GF + GNP)/Cu composites to reduce the anisotropy of the thermal and mechanical properties in GF/Cu composites. In this study, we investigated the effects of GNP addition on the anisotropy of the thermal and mechanical properties and the deformation behavior of (GF + GNP)/Cu composites. The 2 θ > value was used to evaluate the alignment of the reinforcing phases (GF, GNP), by which the variations in the coefficient of thermal expansion (CTE) and thermal conductivity (TC) of the composites were analyzed. With increasing GNP volume fraction, the angle (θ) at which the GF deviated from the in-plane direction increased. As a result, the anisotropy of the CTE in the in-plane and through-plane directions increased, whereas the anisotropy of the TC and mechanical strength decreased. Cracking was observed in both the specimens compressed along the in-plane and through-plane directions, whereas kinking was observed only in the specimens compressed along the in-plane direction. The deformation behavior and mechanical properties of the composites with bimodal reinforcement in the in-plane and through-plane directions were strongly dependent on the change in the alignment of the GF with the addition of GNP. The results clearly revealed the role of bimodal reinforcement in controlling the anisotropy of the thermal and mechanical properties of the (GF + GNP)/Cu composite, providing guidelines for optimizing the thermomechanical properties of high-performance (GF + GNP)/Cu composites.

The present study investigates the anisotropic microstructure, nanomechanical and corrosion behavior of Ti–13Nb–13Zr biomedical alloys, which were fabricated using the direct energy deposition (DED) method. The microstructure of the as-deposited material was studied using a field-emission scanning electron microscope (SEM), electron backscatter diffraction (EBSD) and X-ray diffraction (XRD). We found anisotropic mechanical behavior using nanoindentation from strain rate sensitivity and creep tests. For the maximum load of 50 mN, the x-y plane (normal to the building direction) shows better indentation hardness and lower strain rate sensitivity value (0.014) compared to the x-z plane (0.022) (parallel to the building direction). The difference in the indentation hardness was mainly attributed to the smaller equiaxed prior-β grains and finer α’ martensitic laths on the x-y plane. In terms of creep behavior, the x-y planes show better creep strength than the x-z plane. Meanwhile, both planes show a very high creep exponent, which signifies a similar creep mechanism, i.e., dislocation based. Moreover, we further found the anisotropic corrosion behavior using electrochemical tests. Corrosion results reveal that the x-y plane is more corrosion-resistant than the x-z plane. In summary, the x-y plane of the direct energy deposited Ti–13Nb–13Zr alloy possesses better strength and corrosion resistance due to its finer microstructure.

6061 aluminum (Al) alloys were asymmetrically rolled to apply shear deformation, and the effects of pre/post-aging treatment on the mechanical properties and texture evolution were analyzed. The texture was analyzed using electron backscattered diffraction (EBSD), and the formability and planar anisotropy of the specimen were evaluated using the r¯-value and Δr-value calculated from the plastic strain ratios (r-values). Regardless of the aging conditions (no aging, pre-aging, and post-aging), asymmetric rolling yielded higher strength than symmetric rolling. Pre-aged specimens, regardless of the rolling method (symmetric rolling or asymmetric rolling), exhibited higher strength than the post-aged specimens. To develop the //ND shear texture throughout the specimen, asymmetric rolling in a supersaturated solid solution without an initial precipitate was more effective than asymmetrically rolling an aged-hardened specimen. Considering the strength, formability (r¯-value), and planar anisotropy (Δr-value) of the 6061 Al alloy, the asymmetrically rolled pre-aged specimen had the best mechanical properties. These results show that the strength and formability of the 6061 Al alloy can be improved and its planar anisotropy can be reduced using a combination of asymmetric rolling and control of the aging sequence. This work demonstrates how the deformation and heat treatment of Al alloys could be used to increase the adoptability of Al alloys for automobiles.

Dental 3D modeling plays a pivotal role in digital dentistry, offering precise tools for treatment planning, implant placement, and prosthesis customization. Traditional methods rely on physical plaster casts, which pose challenges in storage, accessibility, and accuracy, fueling interest in digitization using 3D computed tomography (CT) imaging. We introduce a method that can reduce both artifacts simultaneously. To validate the proposed method, we carried out CT scan experiments using plaster dental casts created from dental impressions. After the artifact correction, the CT image quality was greatly improved in terms of image uniformity, contrast-to-noise ratio (CNR), and edge sharpness. We examined the correction effects on the accuracy of the 3D models generated from the CT images. As referenced to the 3D models derived from the optical scan data, the root mean square (RMS) errors were reduced by 8.8~71.7% for three dental casts of different sizes and shapes. Our method offers a solution to challenges posed by artifacts in CT scanning of plaster dental casts, leading to enhanced 3D model accuracy. This advancement holds promise for dental professionals seeking precise digital modeling for diverse applications in dentistry.

Ti6Al4V (Ti64) is a versatile material, finding applications in a wide range of industries due to its unique properties. However, hydrogen embrittlement (HE) poses a challenge in hydrogen-rich environments, leading to a notable reduction in strength and ductility. This study investigates the complex interplay of solute hydrogen (SH) and hydride phase (HP) formation in Ti64 by employing two different current densities during the charging process. Nanoindentation measurements reveal distinct micro-mechanical behavior in base metal, SH, and HP, providing crucial insights into HE mechanisms affecting macro-mechanical behavior. The fractography and microstructural analysis elucidate the role of SH and HP in hydrogen-assisted cracking behaviors. The presence of SH heightens intergranular cracking tendencies. In contrast, the increased volume of HP provides sites for crack initiation and propagation, resulting in a two-layer brittle fracture pattern. The current study contributes to a comprehensive understanding of HE in Ti6Al4V, essential for developing hydrogen-resistant materials.

The phenomenon of hydrogen embrittlement (HE) in metals and alloys, which determines the performance of components in hydrogen environments, has recently been drawing considerable attention. This study explores the interplay between strain rates and solute hydrogen in inducing HE of Ti6Al4V alloy. For the hydrogen-charged sample, as the strain rate was decreased from 10−2/s to 10−5/s, the ductility decreased significantly, but the HE effect on mechanical strength was negligible. The low strain rate (LSR) conditions facilitated the development of high-angle grain boundaries, providing more pathways for hydrogen diffusion and accumulation. The presence of solute hydrogen intensified the formation of nano/micro-voids and intergranular cracking tendencies, with micro-crack occurrences observed exclusively in the LSR conditions. These factors expanded the brittle hydrogen-damaged region more deeply into the interior of the lattice. This, in turn, accelerated both crack initiation and intergranular crack propagation, finally resulting in a considerable HE effect and a reduction in ductility at the LSR. The current study underscores the influence of strain rate on HE, enhancing the predictability of longevity and improving the reliability of components operating in hydrogen-rich environments under various loading conditions.

This study investigates the tensile behaviors of additively manufactured (AM) 17-4PH stainless steels heat-treated within various temperature ranges from 400 °C to 700 °C in order to identify the effective aging temperature. Despite an aging treatment of 400–460 °C increasing the retained austenite content, an enhancement of the tensile properties was achieved without a strength-ductility trade-off owing to precipitation hardening by the Cu particles. Due to the intricate evolution of the microstructure, aging treatments above 490 °C led to a loss in yield strength and ductility. A considerable rise in strength and a decrease in ductility were brought about by the increase in the fraction of precipitation-hardened martensitic matrix in aging treatments over 640 °C. The impact of heat-treatment pathways on aging effectiveness and tensile anisotropy was then examined. Direct aging at 482 °C for an hour had hardly any effect on wrought 17-4PH, but it increased the yield strength of AM counterparts from 436–457 to 588–604 MPa. A solid-solution treatment at 1038 °C for one hour resulted in a significant drop in the austenite fraction, which led to an increase in the yield (from 436–457 to 841–919 MPa) and tensile strengths (from 1106–1127 to 1254–1256 MPa) with a sacrifice in ductility. Improved strength and ductility were realized by a solid-solution followed by an aging treatment, achieving 1371–1399 MPa. The tensile behaviors of AM 17-4PH were isotropic both parallel and perpendicular to the building direction.

Particle-reinforced metal matrix composites (MMCs) with high-volume-fraction of above 40% are highly attractive in the field of structural materials because they impart enhanced reinforcement properties to metals. However, high-volume-fraction MMCs are not widely used due to their brittleness. Therefore, overcoming the brittleness of the high-volume-fraction composites is the first step to disseminate the high-reinforcement-fraction composites. In this study, the interface bonding of 55 vol% Al/SiCp composites was strengthened by modifying the interface characteristics to achieve high plasticity of the high-volume-fraction composite. The interface bonding strengthening was conducted by thermal oxidation of SiCp reinforcement. The increased plasticity of the composites was observed as the 62.2% increased fracture strain in the compression test. The interface modification changed the crack path during a compression test from interface crack to reinforcement particle crack. To investigate the mechanism of interface modification, in-situ neutron diffraction experiments were performed under compression. When the plasticity is enhanced by the interface treatment, most fractures consist of reinforcement fractures rather than interface fractures. Therefore, it is confirmed that controlling the interface treatment is a key factor to improve the plasticity in high-volume-fraction composites. This work shed light on developing new composite material with high-volume-fraction reinforcement.

Abstract We demonstrated the design of pre-additive manufacturing microalloying elements in tuning the microstructure of iron (Fe)-based alloys for their tunable mechanical properties. We tailored the microalloying stoichiometry of the feedstock to control the grain sizes of the metallic alloy systems. Two specific microalloying stoichiometries were reported, namely biodegradable iron powder with 99.5% purity (BDFe) and that with 98.5% (BDFe-Mo). Compared with the BDFe, the BDFe-Mo powder was found to have lower coefficient of thermal expansion (CTE) value and better oxidation resistance during consecutive heating and cooling cycles. The selective laser melting (SLM)-built BDFe-Mo exhibited high ultimate tensile strength (UTS) of 1200 MPa and fair elongation of 13.5%, while the SLM-built BDFe alloy revealed a much lower UTS of 495 MPa and a relatively better elongation of 17.5%, indicating the strength enhancement compared with the other biodegradable systems. Such an enhanced mechanical behavior in the BDFe-Mo was assigned to the dominant mechanism of ferrite grain refinement coupled with precipitate strengthening. Our findings suggest the tunability of outstanding strength-ductility combination by tailoring the pre-additive manufacturing microalloying elements with their proper concentrations.

The role of residual stress is critical, particularly for machine tools demanding accuracy below 1 µm. Although minor stresses are subjected to a tiny area, the applied force can cause devastating distortions on the precision components at this length scale. In this research, we systematically investigated the residual stress in a stress frame of the gray iron used in machine tools using synchrotron X-ray and neutron sources. Through the combination of these techniques, the residual stresses on the surface, inside the bulk, and in average were presented. Comprehensive analysis results shed light on the vibratory stress relief technique, which reduced the residual stresses and stabilized them, even materials undergoing cycling heating. Although compressive stresses are not effectively reduced, this technique is useful in improving the mechanical stability of the materials in machine tools.

Metal artifacts in dental computed tomography (CT) images, caused by highly X-ray absorbing objects, such as dental implants or crowns, often more severely compromise image readability than in medical CT images. Since lower tube voltages are used for dental CTs in spite of the more frequent presence of metallic objects in the patient, metal artifacts appear more severely in dental CT images, and the artifacts often persist even after metal artifact correction. The direct sinogram correction (DSC) method, which directly corrects the sinogram using the mapping function derived by minimizing the sinogram inconsistency, works well in the case of mild metal artifacts, but it often fails to correct severe metal artifacts. We propose a modified DSC method to reduce severe metal artifacts, and we have tested it on human dental images. We first segment the metallic objects in the CT image, and then we forward-project the segmented metal mask to identify the metal traces in the projection data with computing the metal path length for the rays penetrating the metal mask. In the sinogram correction with the DSC mapping function, we apply the weighting proportional to the metal path length. We have applied the proposed method to the phantom and patient images taken at the X-ray tube voltage of 90 kVp. We observed that the proposed method outperforms the original DSC method when metal artifacts were severe. However, we need further extensive studies to verify the proposed method for various CT scan conditions with many more patient images.

A district heating system is an eco-friendly power generation facility with high energy efficiency. The boiler water wall tube used in the district heating system is exposed to extremely harsh conditions, and unexpected fractures often occur during operation. In this study, a corrosion failure analysis of the boiler water wall tube was performed to elucidate the failure mechanisms. The study revealed that overheating by flames was the cause of the failure of the boiler water wall tube. With an increase in temperature in a localized region the microstructure not only changed from ferrite/pearlite to martensite/bainite, which made it more susceptible to brittleness, but it also developed tensile residual stresses in the water-facing side by generating cavities or microcracks along the grain boundaries inside the tube. High-temperature hydrogen embrittlement combined with stress corrosion cracking initiated many microcracks inside the tube and created an intergranular fracture.

Influences of chemical dilution and the number of weld layers on residual stresses in a multi-pass low-transformation-temperature (LTT) weld were investigated by finite element modelling and neutron diffraction. A coupled thermal-metallurgical-mechanical (TMM) model that took into account the chemical dilution effect was developed to simulate the complex LTT welding phenomena. The model was strictly validated by comparing the predictions with experimental measurements and the results found good agreement between them. The results showed that a transformation strain caused by LTT martensitic transformation introduced large compressive residual stresses (−500 MPa) into the weld zone and the quantities were closely related to the chemical dilution between welding layers. Simulation results revealed that the chemical dilution helped mitigate the large localized tensile residual stresses by modulating the phase transformation process and a single LTT layer was sufficient to generate high compression near the weld surface (~2.5 mm), which suggests a great importance for repair welding. Keywords: Finite element analysis, Thermal-metallurgical-mechanical model, Martensitic transformation, Residual stress, Chemical dilution, Multi-pass weld

In this study, we manufactured a non-equiatomic (CoNi)74.66Cr17Fe8C0.34 high-entropy alloy (HEA) consisting of a single-phase face-centered-cubic structure. We applied in situ neutron diffraction coupled with electron backscattered diffraction (EBSD) and transmission electron microscopy (TEM) to investigate its tensile properties, microstructural evolution, lattice strains and texture development, and the stacking fault energy. The non-equiatomic (CoNi)74.66Cr17Fe8C0.34 HEA revealed a good combination of strength and ductility in mechanical properties compared to the equiatomic CoNiCrFe HEA, due to both stable solid solution and precipitation-strengthened effects. The non-equiatomic stoichiometry resulted in not only a lower electronegativity mismatch, indicating a more stable state of solid solution, but also a higher stacking fault energy (SFE, ~50 mJ/m2) due to the higher amount of Ni and the lower amount of Cr. This higher SFE led to a more active motion of dislocations relative to mechanical twinning, resulting in severe lattice distortion near the grain boundaries and dislocation entanglement near the twin boundaries. The abrupt increase in the strain hardening rate (SHR) at the 1~3% strain during tensile deformation might be attributed to the unusual stress triaxiality in the {200} grain family. The current findings provide new perspectives for designing non-equiatomic HEAs.

Cone-beam dental CT can provide high-precision 3D images of the teeth and surrounding bones. From the 3D CT images, 3D models, also called digital impressions, can be computed for CAD/CAM-based fabrication of dental restorations or orthodontic devices. However, the cone-beam angle-dependent artifacts, mostly caused by the incompleteness of the projection data acquired in the circular cone-beam scan geometry, can induce significant errors in the 3D models. Using a micro-CT, we acquired CT projection data of plaster cast models at several different cone-beam angles, and we investigated the dependency of the model errors on the cone-beam angle in comparison with the reference models obtained from the optical scanning of the plaster models. For the 3D CT image reconstruction, we used the conventional Feldkamp algorithm and the combined half-scan image reconstruction algorithm to investigate the dependency of the model errors on the image reconstruction algorithm. We analyzed the mean of positive deviations and the mean of negative deviations of the surface points on the CT-image-derived 3D models from the reference model, and we compared them between the two image reconstruction algorithms. It has been found that the model error increases as the cone-beam angle increases in both algorithms. However, the model errors are smaller in the combined half-scan image reconstruction when the cone-beam angle is as large as 10 degrees.

The objective of this study was to evaluate susceptibility changes caused by iron accumulation in cognitive normal (CN) elderly, those with amnestic mild cognitive impairment (aMCI), and those with early state AD, and to compare the findings with gray matter volume (GMV) changes caused by neuronal loss. The participants included 19 elderly CN, 19 aMCI, and 19 AD subjects. The voxel-based quantitative susceptibility map (QSM) and GMV in the brain were calculated and the differences of those insides were compared among the three groups. The differences of the QSM data and GMVs among the three groups were investigated by voxel-based and region of interest (ROI)-based comparisons using a one-way analysis of covariance (ANCOVA) test with the gender and age as covariates. Finally, a receiver-operating-characteristic (ROC) curve analysis was performed. The voxel-based results showed that QSM demonstrated more areas with significant difference between the CN and AD groups compared to GMV. GMVs were decreased, but QSM values were increased in aMCI and AD groups compared with the CN group. QSM better differentiated aMCI from CN than GMV in the precuneus and allocortex regions. In the accumulation regions of iron and amyloid β, QSM can be used to differentiate between CN and aMCI groups, indicating a useful an auxiliary imaging for early diagnosis of AD. Keywords: Alzheimer's disease (AD), Mild cognitive impairment (MCI), Quantitative susceptibility mapping (QSM), Gray matter volume

This review summarizes the state of high-entropy alloys and their combinatorial approaches, mainly considering their magnetic applications. Several earlier studies on high-entropy alloy properties, such as magnetic, wear, and corrosion behavior; different forms, such as thin films, nanowires, thermal spray coatings; specific treatments, such as plasma spraying and inclusion effects; and unique applications, such as welding, are summarized. High-entropy alloy systems that were reported for both their mechanical and magnetic properties are compared through the combination of their Young’s modulus, yield strength, remanent induction, and coercive force. Several potential applications requiring both mechanical and magnetic properties are reported.

In situ neutron diffraction was employed to examine the phase transformation behavior of high-Mn steels with different carbon contents (0.1, 0.3, and 0.5 wt.%C). With increasing carbon contents from 0.1 C to 0.5 C, the austenite phase fraction among the constituent phases increased from ~66% to ~98%, and stacking fault energy (SFE) increased from ~0.65 to ~16.5 mJ/m2. The 0.1 C and 0.3 C steels underwent phase transformation from γ-austenite to ε-martensite or α’-martensite during tensile deformation. On the other hand, the 0.5 C steel underwent phase transformation only from γ-austenite to ε-martensite. The 0.3 C steel exhibited a low yield strength, a high strain hardening rate, and the smallest elongation. The high strain hardening of the 0.3 C alloy was due to a rapid phase transformation rate from γ-austenite to ε-martensite. The austenite of 0.5 C steel was strengthened by mechanical twinning during loading process, and the twinning-induced plasticity (TWIP) effect resulted in a large ductility. The 0.5 wt.% carbon addition stabilized the austenite phase by delaying the onset of the ε-martensite phase transformation.

We investigated the evolution of the strain fields around a fatigued crack tip between the steady- and overloaded-fatigue conditions using a nondestructive neutron diffraction technique. The two fatigued compact-tension specimens, with a different fatigue history but an identical applied stress intensity factor range, were used for the direct comparison of the crack tip stress/strain distributions during in situ loading. While strains behind the crack tip in the steady-fatigued specimen are irrelevant to increasing applied load, the strains behind the crack tip in the overloaded-fatigued specimen evolve significantly under loading, leading to a lower driving force of fatigue crack growth. The results reveal the overload retardation mechanism and the correlation between crack tip stress distribution and fatigue crack growth rate.

X-ray mammography is commonly used to scan cancer or tumors in breast using low dose x-rays. But mammograms suffer from low contrast problem. The breast is compressed in mammography to reduce x-ray scattering effects. As tumors are stiffer than normal tissues, they undergo smaller deformation under compression. Therefore, image intensity at tumor region may change less than the background tissues. In this study, we try to find out compression induced contrast from multiple mammographic images of tumorous breast phantoms taken with different compressions. This is an extended work of our previous simulation study with experiment and more analysis. We have used FEM models for synthetic phantom and constructed a phantom using agar and n-propanol for simulation and experiment. The x-ray images of deformed phantoms have been obtained under three compression steps and a non-rigid registration technique has been applied to register these images. It is noticeably observed that the image intensity changes at tumor are less than those at surrounding which induce a detectable contrast. Addition of this compression induced contrast to the simulated and experimental images has improved their original contrast by a factor of about 1.4

In situ neutron diffraction has been used to examine the deformation mechanisms of a precipitation-hardened and extruded Mg-8.5wt.%Al alloy subjected to (i) compression followed by reverse tension (texture T1) and (ii) tension followed by reverse compression (texture T2). Two starting textures are used: (1) as-extruded texture, T1, in which the basal pole of most grains is normal to the extrusion axis and a small portion of grains are oriented with the basal pole parallel to the extrusion axis; (2) a reoriented texture, T2, in which the basal pole of most grains is parallel to the extrusion axis. For texture T1, the onset of extension twinning corresponds well with the macroscopic elastic-plastic transition during the initial compression stage. The non-linear macroscopic stress/strain behavior during unloading after compression is more significant than during unloading after tension. For texture T2, little detwinning occurs after the initial tension stage, but almost all of the twinned volumes are detwinned during loading in reverse compression.

An equal-molar CoCrFeMnNi, face-centered-cubic (fcc) high-entropy alloy (HEA) and a nickel-based superalloy are studied using in situ neutron diffraction experiments. With continuous measurements, the evolution of diffraction peaks is collected for microscopic lattice strain analyses. Cyclic hardening and softening are found in both metallic systems. However, as obtained from the diffraction-peak-width evolution, the underneath deformation mechanisms are quite different. The CoCrFeMnNi HEA exhibits distinct lattice strain and microstructure responses under tension-compression cyclic loadings.

We introduce an efficient ring artifact correction method for a cone-beam computed tomography (CT). In the first step, we correct the defective pixels whose values are close to zero or saturated in the projection domain. In the second step, we compute the mean value at each detector element along the view angle in the sinogram to obtain the one-dimensional (1D) mean vector, and we then compute the 1D correction vector by taking inverse of the mean vector. We multiply the correction vector with the sinogram row by row over all view angles. In the third step, we apply a Gaussian filter on the difference image between the original CT image and the corrected CT image obtained in the previous step. The filtered difference image is added to the corrected CT image to compensate the possible contrast anomaly that may appear due to the contrast change in the sinogram after removing stripe artifacts. We applied the proposed method to the projection data acquired by two flat-panel detectors (FPDs) and a silicon-based photon-counting X-ray detector (PCXD). Micro-CT imaging experiments of phantoms and a small animal have shown that the proposed method can greatly reduce ring artifacts regardless of detector types. Despite the great reduction of ring artifacts, the proposed method does not compromise the original spatial resolution and contrast.

Fast and accurate energy calibration of photon counting spectral detectors (PCSDs) is essential for their biomedical applications to identify and characterize bio-components or contrast agents in tissues. Using the x-ray tube voltage as a reference for energy calibration is known to be an efficient method, but there has been no consideration in the energy calibration of non-convergent behavior of PCSDs. We observed that a single pixel mode (SPM) CdTe PCSD based on Medipix-2 shows some non-convergent behaviors in turning off the detector elements when a high enough threshold is applied to the comparator that produces a binary photon count pulse. More specifically, the detector elements are supposed to stop producing photon count pulses once the threshold reaches a point of the highest photon energy determined by the tube voltage. However, as the x-ray exposure time increases, the threshold giving 50% of off pixels also increases without converging to a point. We established a method to take account of the non-convergent behavior in the energy calibration. With the threshold-to-photon energy mapping function established by the proposed method, we could better identify iodine component in a phantom consisting of iodine and other components.

Mesenchymal stromal cells (MSCs) are multipotent cells found in several adult tissues; they have the capacity to differentiate into mesodermal, ectodermal, and endodermal tissues in vitro. There have been several reports that MSCs have therapeutic effects in a variety of diseases. Therefore, using a cell labeling technique, monitoring their temporal and spatial migration in vivo, would be useful in the clinical setting. Magnetic resonance imaging (MRI)—tracking of superparamagnetic iron oxide (SPIO)-labeled cells—is a noninvasive technique for determining the location and migration of transplanted cells. In the present study, we evaluated the influence and toxicity of SPIO (ferumoxides) labeling on multiple differentiated MSCs. To evaluate the influence and toxicity of ferumoxides labeling on differentiation of MSCs, a variety of concentrations of ferumoxides were used for labeling MSCs. We found that the cytoplasm of adherent cells was effectively labeled at low concentrations of ferumoxides. Compared with unlabeled controls, the ferumoxides-labeled MSCs exhibited a similar proliferation rate and apoptotic progression. The labeled MSCs differentiated into osteoblasts and adipocytes in an identical fashion as the unlabeled cells. However, chondrogenesis and neurogenesis were inhibited at high concentrations of ferumoxides. Our results suggest the effective concentration for ferumoxides use in tracking MSCs.