Search

Selective removal of ions from water via capacitive deionization (CDI) is relevant for environmental and industrial applications like water purification, softening, and resource recovery. Prussian blue analogs (PBAs) are proposed as an electrode material for selectively removing cations from water, based on their size. So far, PBAs used in CDI are selective toward monovalent ions. Here, vanadium hexacyanoferrate (VHCF), a PBA, is introduced as a new electrode material in a hybrid CDI setup to selectively remove divalent cations from water. These electrodes prefer divalent Ca2+over monovalent Na+, with a separation factor, βCa/Na≈3.5. This finding contrasts with the observed monovalent ion selectivity by PBA electrodes. This opposite behavior is understood by density functional theory simulations. Furthermore, coating the VHCF electrodes with a conducting polymer (poly-pyrrole, doped with poly-styrenesulphonate) prevents the contamination of the treated water following the degradation of the electrode. This facile and modular coating method can be effortlessly extended to other PBA electrodes, limiting the extent of treated water contamination during repeated cycling. This study paves the way for tunable selectivity while extending the library of electrodes that can be successfully used in (selective) CDI.

Microporous polymer frameworks have attracted considerable attention to make novel separation layers owing to their highly porous structure, high permeability, and excellent molecular separation. This study concerns the fabrication and properties of thin melamine-based microporous polymer networks with a layer thickness of around 400 nm, supported on an α-alumina support and their potential use in organic solvent nanofiltration. The modified membranes show excellent solvent purification performances, such as n-heptane permeability as high as 9.2 L m−2 h−1 bar −1 in combination with a very high rejection of approximately 99 % for organic dyes with molecular weight of ≥457 Da. These values are higher than for the majority of the state-of-the-art membranes. The membranes further exhibit outstanding long-term operation stability. This work significantly expands the possibilities of using ceramic membranes in organic solvent nanofiltration.

To the best of our knowledge, for the first time MIL-53(Al) and NH 2 -MIL-53(Al) modified α-alumina membranes are investigated for the adsorption of organic dyes from organic solvents. These new, modified membranes show excellent adsorption of high concentrations of Rose Bengal dye in methanol and isopropanol solutions.

Silicon semiconductors with a thin surface layer of silica were first modified with polyelectrolytes (polyethyleneimine, polystyrene sulfonate and poly(allylamine)) via a facile layer-by-layer deposition approach. Subsequently, lipid vesicles were added to the preformed polymeric cushion, resulting in the adsorption of intact vesicles or fusion and lipid bilayer formation. To study involved interactions we employed optical reflectometry, electrochemical impedance spectroscopy and fluorescent recovery after photobleaching. Three phospholipids with different charge of polar head groups, i.e. 1,2-dioleoyl-sn-glycero-3-phosphocholine (DOPC), 1,2-dioleoyl-sn-glycero-3-phospho-L-serine (DOPS) and 1,2-dioleoyl-3-trimethylammonium-propane (DOTAP) were used to prepare vesicles with varying surface charge. We observed that only lipid vesicles composed from 1:1 (mole:mole) mixture of DOPC/DOPS have the ability to fuse onto an oppositely charged terminal layer of polyelectrolyte giving a lipid bilayer with a resistance of >100 kΩ. With optical reflectometry we found that the vesicle surface charge is directly related to the amount of mass adsorbed onto the surface. An interesting observation was that zwitterionic polar head groups of DOPC allow the adsorption on both positively and negatively charged surfaces. As found with fluorescent recovery after photobleaching, positively charged surface governed by the presence of poly(allylamine) as the terminal layer resulted in intact DOPC lipid vesicles adsorption whereas in the case of a negatively charged silica surface formation of lipid bilayers was observed, as expected from literature.

The electrochemical behavior of three differently charged drug molecules (zwitter-ionic acetylcarnitine, bi-cationic succinylcholine and tri-cationic gallamine) was studied at the interface between two immiscible electrolyte solutions. Tetramethylammonium was used as a model mono cationic molecule and internal reference. The charge and molecular structure were found to play an important role in the drug lipophilicity. The studied drugs gave a linear correlation between the water – octanol (logPoctanol) partition coefficients and the electrochemically measured water – 1,2-dichloroethane (logPDCE) partition coefficients. Comparison with tetraalkylammonium cations indicating that the correlation between logPoctanol and logPDCE is molecular structure dependent. The highest measured sensitivity and lowest limit of detection were found to be 0.543 mA·dm3·mol− 1 and 6.25 μM, respectively, for the tri-cationic gallamine. The sensitivity for all studied ions was found to be a linear function of molecular charge. The dissociation constant of the carboxylic group of zwiter-ionic acetylcarnitine was calculated based on voltammetric parameters and was found to be 4.3. This study demonstrates that electrochemistry at the liquid – liquid interface is powerful technique when it comes to electroanalytical or pharmacokinetic drug assessment.

Affinity layers play a crucial role in chemical sensors for the selective and sensitive detection of analytes. Here, we report the use of composite affinity layers containing Metal Organic Frameworks (MOFs) in a polymeric matrix for sensing purposes. Nanoparticles of NH2-MIL-53(Al) were dispersed in a Matrimid polymer matrix with different weight ratios (0-100 wt %) and drop-casted on planar capacitive transducer devices. These coated devices were electrically analyzed using impedance spectroscopy and investigated for their sensing properties toward the detection of a series of alcohols and water in the gas phase. The measurements indicated a reversible and reproducible response in all devices. Sensor devices containing 40 wt % NH2-MIL-53(Al) in Matrimid showed a maximum response for methanol and water. The sensor response time slowed down with increasing MOF concentration until 40 wt %. The half time of saturation response (τ0.5) increased by ∼1.75 times for the 40 wt % composition compared to devices coated with Matrimid only. This is attributed to polymer rigidification near the MOF/polymer interface. Higher MOF loadings (≥50 wt %) resulted in brittle coatings with a response similar to the 100 wt % MOF coating. Cross-sensitivity studies showed the ability to kinetically distinguish between the different alcohols with a faster response for methanol and water compared to ethanol and 2-propanol. The observed higher affinity of the pure Matrimid polymer toward methanol compared to water allows also for a higher uptake of methanol in the composite matrices. Also, as indicated by the sensing studies with a mixture of water and methanol, the methanol uptake is independent of the presence of water up to 6000 ppm of water. The NH2-MIL-53(Al) MOFs dispersed in the Matrimid matrix show a sensitive and reversible capacitive response, even in the presence of water. By tuning the precise compositions, the affinity kinetics and overall affinity can be tuned, showing the promis