Search

Hard magnetic (HM) thin films have been vertically integrated below giant magnetoresistive (GMR) multilayer sensors in order to shift the operating point of an applicable GMR sensor. The shift in maximum magnetoresistance (MR) peaks was found to be dependent on the thickness of the HM layer. As a result of different bias geometries, which have been tested, current shunting effects mainly reduce the maximum MR amplitudes. A strong microstructural influence on the magnetotransport has been found; meander-shaped microstructures with different stripe widths have been microfabricated in order to investigate the influence of shape anisotropy and stray field geometry on the magnetotransport. As a result, the bias strength, as well as the shape of the HM hysteresis, varies with the underlying microstructured pattern geometries and the angle of applied field. Comparing the major MR loops of meanders with 1.5, 5, and 10 μm structure width of HM/GMR systems, different MR behavior has been found. It was determined that the MR loops are shifted by different field values simultaneously with a change in the MR loop shape. The effect depends on the orientation of applied field with respect to the meander structure, as well as on the structure width. A creeping effect, which demagnetizes the hard layer, has not been observed during sine-shaped switching cycles. The MR response signal of biased multilayers can be understood using numerical calculations. © 2004 American Institute of Physics. [ABSTRACT FROM AUTHOR]

A method for the realization of low-loss integrated optical components is proposed and demonstrated. This approach is simple, fast, inexpensive, scalable for mass production, and compatible with both 2D and 3D geometries. The process is based on a novel dual-step soft nano imprint lithography process for producing devices with smooth surfaces, combined with fast sol-gel technology providing highly transparent materials. As a concrete example, this approach is demonstrated on a micro ring resonator made by direct laser writing (DLW) to achieve a quality factor improvement from one hundred thousand to more than 3 million. To the best of our knowledge this also sets a Q-factor record for UV-curable integrated micro-ring resonators. The process supports the integration of many types of materials such as light-emitting, electro-optic, piezo-electric, and can be readily applied to a wide variety of devices such as waveguides, lenses, diffractive elements and more.

We compare different excitation and collection configurations based on free-space optics and evanescently coupled tapered fibers for both lasing and fluorescence emission from dye-doped doped polymeric whispering gallery mode (WGM) micro-disk lasers. The focus of the comparison is on the lasing threshold and efficiency of light collection. With the aid of optical fibers, we localize the pump energy to the cavity-mode volume and reduce the necessary pump energy to achieve lasing by two orders of magnitude. When using fibers for detection, the collection efficiency is enhanced by four orders of magnitude compared to a free-space read-out perpendicular to the resonator plane. By enhancing the collection efficiency we are able to record a pronounced modulation of the dye fluorescence under continuous wave (cw) pumping conditions evoked by coupling to the WGMs. Alternatively to fibers as a collection tool, we present a read-out technique based on the detection of in-plane radiated light. We show that this method is especially beneficial in an aqueous environment as well as for size-reduced micro-lasers where radiation is strongly pronounced. Furthermore, we show that this technique allows for the assignment of transverse electric (TE) and transverse magnetic (TM) polarization to the observed fundamental modes in a water environment by performing polarization-dependent photoluminescence (PL) spectroscopy. We emphasize the importance of the polarization determination for sensing applications and verify expected differences in the bulk refractive index sensitivity for TE and TM WGMs experimentally.

We demonstrate the realization of 3D whispering-gallery-mode (WGM) microlasers by direct laser writing (DLW) and their replication by nanoimprint lithography using a soft mold technique ("soft NIL"). The combination of DLW as a method for rapid prototyping and soft NIL offers a fast track towards large scale fabrication of 3D passive and active optical components applicable to a wide variety of materials. A performance analysis shows that surface-scattering-limited Q-factors of replicated resonators as high as 1×10 5 at 635 nm can be achieved with this process combination. Lasing in the replicated WGM resonators is demonstrated by the incorporation of laser dyes in the target material. Low lasing thresholds in the order of 15  kW/cm 2 are obtained under ns-pulsed excitation.

Integration of optically active materials into whispering gallery mode (WGM) cavities enables low-threshold laser emission. In contrast to their passive counterparts, the WGMs of these microlasers can be pumped and read out easily via free-space optics. The WGMs interact with the cavity environment via their evanescent field, and thus lend themselves to label-free bio-sensing. The detection limit of such sensors, given as the ratio of the resolution of the whole measurement system to the sensitivity of the WGMs, is an important figure of merit. In this work we show that the detection limit of polymeric microdisk lasers can be improved by more than a factor of seven by optimizing their radius and thickness. We use the bulk refractive index sensitivity, the magnitude of the sensor reaction towards refractive index changes of the bulk environment, to quantify the sensing performance and show that it can be enhanced while the spectral resolution is maintained. Furthermore, we investigate the effect of the size of the cavity on the quality factor and the lasing threshold in an aqueous environment, hence allowing optimization of the cavity size for enhanced sensor performance. For all considered quantities, numerically computed expectations are verified by experimental results.

Optical micro-resonators have broad applications. They are used, for example, to enhance light-matter interactions in optical sensors or as model systems for investigating fundamental physical mechanisms in cavity quantum electrodynamics. Coupling two or more micro-cavities is particularly interesting as it enlarges the design freedom and the field of application. In this context, achieving tunability of the coupling strength and hence the inter-cavity gap is of utmost importance for adjusting the properties of the coupled micro-resonator system. In this paper, we report on a novel coupling approach that allows highly precise tuning of the coupling gap of polymeric micro-resonators that are fabricated side by side on a common substrate. We structure goblet-shaped whispering-gallery-mode resonators on an elastic silicone-based polymer substrate by direct laser writing. The silicone substrate is mechanically stretched in order to exploit the lateral shrinkage to reduce the coupling gap. Incorporating a laser dye into the micro-resonators transforms the cavities into micro-lasers that can be pumped optically. We have investigated the lasing emission by micro-photoluminescence spectroscopy, focusing on the spatial localization of the modes. Our results demonstrate the formation of photonic molecules consisting of two or even three resonators, for which the coupling strengths and hence the lasing performance can be precisely tuned. Flexibility and tunability are key elements in future photonics, making our approach interesting for various photonic applications. For instance, as our coupling approach can also be extended to larger cavity arrays, it might serve as a platform for tunable coupled-resonator optical waveguide devices., Competing Interests: The authors declare no conflict of interest.

The selection of an appropriate booklet design is an important element of large-scale assessments of student achievement. Two design properties that are typically optimized are the balance with respect to the positions the items are presented and with respect to the mutual occurrence of pairs of items in the same booklet. The purpose of this study is to investigate the effects of these two design properties on bias and root mean square error of item parameter estimates from the Rasch model. First, position effects are estimated using data from a large-scale assessment study measuring the competencies of 19,107 ninth graders in science. These results were then used for a simulation study with 1,540 booklet designs with systematically varied position balance and cluster pair balance. The simulation results showed a small effect of position balancing on bias and root mean square error of the item parameter estimates while the cluster pair balance was ignorable. This null effect is actually good news for test designers since it allows for deliberately reducing the degree of cluster pair balance without negative effects on item parameter estimates. However, it is recommended to try to achieve a high position balance when designing large-scale assessment studies., Competing Interests: Declaration of Conflicting Interests: The author(s) declared no potential conflicts of interest with respect to the research, authorship, and/or publication of this article.

We present an all-polymer photonic sensing platform based on whispering-gallery mode microgoblet lasers integrated into a microfluidic chip. The chip is entirely made from polymers, enabling the use of the devices as low-cost disposables. The microgoblet cavities feature quality factors exceeding 10(5) and are fabricated from poly(methyl methacrylate) (PMMA) using spin-coating, mask-based optical lithography, wet chemical etching, and thermal reflow. In contrast to silica-based microtoroid resonators, this approach replaces technically demanding vacuum-based dry etching and serial laser-based reflow techniques by solution-based processing and parallel thermal reflow. This enables scaling to large-area substrates, and hence significantly reduces device costs. Moreover, the resonators can be fabricated on arbitrary substrate materials, e.g., on transparent and flexible polymer foils. Doping the microgoblets with the organic dye pyrromethene 597 transforms the passive resonators into lasers. Devices have lasing thresholds below 0.6 nJ per pulse and can be efficiently pumped via free-space optics using a compact and low-cost green laser diode. We demonstrate that arrays of microgoblet lasers can be readily integrated into a state-of-the-art microfluidic chip replicated via injection moulding. In a proof-of-principle experiment, we show the viability of the lab-on-a-chip via refractometric sensing, demonstrating a bulk refractive index sensitivity (BRIS) of 10.56 nm per refractive index unit.

Multiple matrix designs are commonly used in large-scale assessments to distribute test items to students. These designs comprise several booklets, each containing a subset of the complete item pool. Besides reducing the test burden of individual students, using various booklets allows aligning the difficulty of the presented items to the assumed performance level of examined subgroups. While this may improve measurement precision and students' test-taking motivation, using several booklets might influence response behavior and thus constitute a potential source of unwanted variation. To provide guidance to identify and model booklet effects, this study presents statistical models accounting for booklet effects and applies these models in a large-scale assessment setting. Three models are derived from the Rasch model employing the generalized linear mixed models framework. The models were applied to data from a national educational standards assessment study for scientific competence. A total of 1,021 items were compiled to 74 booklets distributed to a sample of 9,044 students of Grades 9 and 10. The results revealed a small but nonnegligible booklet effect. For further large-scale assessment studies, it is recommended to examine whether booklet effects occur and to adequately account for them in the subsequent analyses where necessary., Competing Interests: Declaration of Conflicting Interests: The author(s) declared no potential conflicts of interest with respect to the research, authorship, and/or publication of this article.