Search

A water-soluble ternary copolymer bearing carboxyl, sulfonic, and amide functional groups was synthesized using ammonium persulfate-catalyzed free radical polymerization in water, resulting in high monomer conversion. This copolymer was then complexed with aluminum sulfate, forming an admixture containing Al(SO4)(OH)·5H2O, which was subsequently combined with silica gel. Characterization revealed that the synthesized copolymer formed a large, thin membrane that covered both the aluminum compounds and the silica gel blocks. The introduction of this complex admixture, combining the copolymer and aluminum sulfate, not only reduced the setting times of the cement paste but also enhanced the mechanical strengths of the mortar compared to using aluminum sulfate alone. The complex admixture led to the formation of katoite, metajennite, and C3A (tricalcium aluminate) in the mortar, demonstrating significant linking effects, whereas pure aluminum sulfate could not completely transform C3S within 24 h. Further addition of silica gel to the complex admixture further shortened the setting times of the paste, slightly reduced compressive strength, but improved flexural strength compared to the initial complex admixture. The silicon components appeared to fill the micropores and mesopores of the mortar, accelerating cement setting and enhancing flexural strength, while slightly decreasing compressive strength. This study contributed to the development of new cementing accelerators with improved hardening properties.

Two water-soluble block copolymers composed of acrylic acid (AA), 2-acrylamido-2-methylpropane sulfonic acid (AMPS), and optionally maleic anhydride (MAH) were synthesized through ammonium persulfate-catalyzed free radical polymerization in water. The introduction of aluminum sulfate (AS) into the resulting mixtures significantly reduced the setting times of the paste and enhanced the mechanical strength of the mortar compared to both the additive-free control and experiments facilitated solely by pure AS. This improvement was primarily attributed to the inhibition of rapid Al3+ hydrolysis, which was achieved through coordination of the synthesized block copolymers, along with the formation of newly identified hydrolytic intermediates. Notably, the ternary copolymer (AA–AMPS–MAH) exhibited superior performance compared to that of the binary copolymer (AA–AMPS). In the early stages of cement setting, clusters of ettringite (AFt) were found to be immobilized over newly detected linkage phases, including unusual calcium silicate hydrate and epistilbite. In contrast to the well-documented role of polymers in retarding cement hydration, this study presents a novel approach by providing both accelerating and hardening agents for cement setting, which has significant implications for the future design of cement additives.

The C-3 modification of 1H-indazole has produced active pharmaceuticals for the treatment of cancer and HIV. But, so far, this transformation has seemed less available, due to the lack of efficient C-C bond formation at the less reactive C-3 position. In this work, a series of silica gel-supported PdO2 nanoparticles of 25–66 nm size were prepared by ball milling silica gel with divalent palladium precursors, and then employed as catalysts for the Suzuki–Miyaura cross-coupling of 1H-indazole derivative with phenylboronic acid. All the synthesized catalysts showed much higher cross-coupling yields than their palladium precursors, and could also be reused three times without losing high activity and selectivity in a toluene/water/ethanol mixed solvent. Although the palladium precursors showed an order of activity of PdCl2(dppf, 1,1′-bis(diphenylphosphino)ferrocene) > PdCl2(dtbpf, 1,1′-bis(di-tert-butylphosphino)ferrocene) > Pd(OAc, acetate)2, the synthesized catalysts showed an order of C1 (from Pd(OAc)2) > C3 (from PdCl2(dtbpf)) > C2 (from PdCl2(dppf)), which conformed to the orders of BET (Brunauer–Emmett–Teller) surface areas and acidities of these catalysts. Notably, the most inexpensive Pd(OAc)2 can be used as a palladium precursor for the synthesis of the best catalyst through simple ball milling. This work provides a highly active and inexpensive series of catalysts for C-3 modification of 1H-indazole, which are significant for the large-scale production of 1H-indazole-based pharmaceuticals.