Search

This study focused on achieving high ionic conductivity in Li-La-TiO (LLTO) solid electrolyte. To enhance ionic conductivity, the synthesis reaction was optimized by controlling the composite crystal structure of TiO2 at the B-site of the perovskite (ABO3) structured LLTO, incorporating rutile, brookite, and anatase phases. The solid-phase LLTO, synthesized utilizing the core – shell structured composite-phase TiO2 developed in this study for the first time, successfully transformed its crystal structure to β-LLTO (tetragonal to cubic). This resulted in a significant improvement in ionic conductivity (i.e. 1.11 × 10−4 Scm−1). The study findings confirmed that the composite crystal structure TiO2 used in the solid-phase synthesis of LLTO induced an increase in oxygen vacancies during the synthesis process, thereby reducing the step-free energy required for the final synthesis.

Titanium carbides reinforced steel matrix (TiC-steel) composites exhibit a range of excellent properties, including increased strength-to-weight ratio, high-temperature strength, and outstanding wear resistance. Prior research has demonstrated that the mechanical properties of TiC-steel composites are significantly affected by particle coarsening and the associated core-rim structure. Nevertheless, the fundamental mechanisms of thermochemical reactions that govern the formation of the final microstructure in these composites, including the core-rim structure, remain incompletely explored. This study elucidates the microstructure evolution mechanism of high-volume TiC-steel composites, particularly particle coarsening, through thermodynamic calculations and chemical analysis. The investigation unveils the coarsening process, shedding light on the formation of more stable phases and associated compositional changes, including the incorporation of substitutional elements and carbon depletion (resulting in low stoichiometry, x

The high-temperature properties of titanium carbide (TiC)–reinforced stainless steel (SS) matrix composite, fabricated through infiltration process, were investigated across different temperatures. By adding highly concentrated and closely adjacent TiC particulate reinforcement, dramatic variations in the coefficient of thermal expansion (CTE) and thermal conductivity properties, which originate from the phase transformation of the SS matrix, were effectively suppressed. Moreover, the addition of TiC significantly strengthened the SS, with its strengthening effect increasing at higher temperatures and reaching its highest value after the phase transformation. Therefore, TiC–SS composite exhibit great potential for use as advanced high-temperature-resistant structural materials.

In this study, solid-state BaTiO3 was successfully synthesized after the disintegration of the starting materials (BaCO3 and TiO2) under various conditions. By analyzing the microstructure, tetragonality, crystallinity, and particle size distribution of the synthesized powder, the factors that affected the properties of the BaTiO3 solid-state synthetic powder were successfully identified. Furthermore, the changes in the dielectric constants (temperature characteristic coefficients) of the sintered specimens were investigated using each powder, according to the dielectric characteristics, high-temperature resistance, and temperature, to identify the direct and indirect relationships between the disintegration conditions, synthetic powders, and sintered specimens. Finally, optimal conditions for the uniform solid-state synthesis of BaTiO3 powder for multilayer ceramic capacitor production were derived.

Particle-reinforced metal matrix composites (MMCs) with high-volume-fraction of above 40% are highly attractive in the field of structural materials because they impart enhanced reinforcement properties to metals. However, high-volume-fraction MMCs are not widely used due to their brittleness. Therefore, overcoming the brittleness of the high-volume-fraction composites is the first step to disseminate the high-reinforcement-fraction composites. In this study, the interface bonding of 55 vol% Al/SiCp composites was strengthened by modifying the interface characteristics to achieve high plasticity of the high-volume-fraction composite. The interface bonding strengthening was conducted by thermal oxidation of SiCp reinforcement. The increased plasticity of the composites was observed as the 62.2% increased fracture strain in the compression test. The interface modification changed the crack path during a compression test from interface crack to reinforcement particle crack. To investigate the mechanism of interface modification, in-situ neutron diffraction experiments were performed under compression. When the plasticity is enhanced by the interface treatment, most fractures consist of reinforcement fractures rather than interface fractures. Therefore, it is confirmed that controlling the interface treatment is a key factor to improve the plasticity in high-volume-fraction composites. This work shed light on developing new composite material with high-volume-fraction reinforcement.

BackgroundWhole-genome sequencing plays a critical role in the genomic epidemiology intended to improve understanding the spread of emerging viruses. Dabie bandavirus, causing severe fever with thrombocytopenia syndrome (SFTS), is a zoonotic tick-borne virus that poses a significant public health threat. We aimed to evaluate a novel amplicon-based nanopore sequencing tool to obtain whole-genome sequences of Dabie bandavirus, also known as SFTS virus (SFTSV), and investigate the molecular prevalence in wild ticks, Republic of Korea (ROK).Principal findingsA total of 6,593 ticks were collected from Gyeonggi and Gangwon Provinces, ROK in 2019 and 2020. Quantitative polymerase chain reaction revealed the presence of SFSTV RNA in three Haemaphysalis longicornis ticks. Two SFTSV strains were isolated from H. longicornis captured from Pocheon and Cheorwon. Multiplex polymerase chain reaction-based nanopore sequencing provided nearly full-length tripartite genome sequences of SFTSV within one hour running. Phylogenetic and reassortment analyses were performed to infer evolutionary relationships among SFTSVs. Phylogenetic analysis grouped SFTSV Hl19-31-4 and Hl19-31-13 from Pocheon with sub-genotype B-1 in all segments. SFTSV Hl20-8 was found to be a genomic organization compatible with B-1 (for L segment) and B-2 (for M and S segments) sub-genotypes, indicating a natural reassortment between sub-genotypes.Conclusion/significanceAmplicon-based next-generation sequencing is a robust tool for whole-genome sequencing of SFTSV using the nanopore platform. The molecular prevalence and geographical distribution of SFTSV enhanced the phylogeographic map at high resolution for sophisticated prevention of emerging SFTS in endemic areas. Our findings provide important insights into the rapid whole-genome sequencing and genetic diversity for the genome-based diagnosis of SFTSV in the endemic outbreak.

In this study, the anatase–rutile phase fraction of TiO2, which would play a vital role in the solid-state synthesis of BaTiO3, was controlled to form a composite phase. The composite TiO2 was applied to a solid-state synthesis reaction, and the tetragonality, dielectric properties, and microstructure of the resulting BaTiO3 powders were analyzed under different synthesis conditions of TiO2. Furthermore, a comparative analysis of solid-state-synthesized BaTiO3 powders prepared using anatase, rutile, and mixed (anatase + rutile) TiO2 was performed to elucidate the mechanism of improvement in the sintering behavior and dielectric properties of the BaTiO3 powder synthesized using the composite TiO2. As a result of applying composite TiO2, BaTiO3 powder with excellent tetragonality was synthesized. In addition, it is effective in powder growth and the control of powder morphology, so sintering and dielectric properties can be improved at relatively low temperatures.

Flu disease, with high mortality and morbidity, is caused by the influenza virus. Influenza infections are most effectively prevented through vaccination, but it requires annual reformulation due to the antigenic shift or drift of hemagglutinin and neuraminidase proteins. Increasing resistance to available anti-influenza drugs was also recently reported. The M2 surface protein of the influenza virus is an attractive target for universal vaccine development as it is highly conserved and multifunctional throughout the viral life cycle. This study aimed to discover a single-chain variable fragment (scFv) targeting the M2 protein of influenza A H1N1/PR8, showing neutralizing activity through plaque inhibition in virus replication. Several candidates were isolated using bio-panning, including scFv and single-domain VL target M2 protein, which was displayed on the yeast surface. The scFv/VL proteins were obtained with high yield and high purity through soluble expression in E. coli BL21 (DE3) pLysE strains. A single-domain VL-M2-specific antibody, NVLM10, exhibited the highest binding affinity to influenza virions and was engineered into a bivalent format (NVL2M10) to improve antigen binding. Both antibodies inhibited virus replication in a dose-dependent manner, determined using plaque reduction- and immunocytochemistry assays. Furthermore, bivalent anti-M2 single-domain VL antibodies significantly reduced the plaque number and viral HA protein intensity as well as viral genome (HA and NP) compared to the monovalent single-domain VL antibodies. This suggests that mono- or bivalent single-domain VL antibodies can exhibit neutralizing activity against influenza virus A, as determined through binding to virus particle activity.

BackgroundHantavirus infection occurs through the inhalation of aerosolized excreta, including urine, feces, and saliva of infected rodents. The presence of Hantaan virus (HTNV) RNA or infectious particles in urine specimens of patient with hemorrhagic fever with renal syndrome (HFRS) remains to be investigated.Methodology/principal findingsWe collected four urine and serum specimens of Republic of Korea Army (ROKA) patients with HFRS. We performed multiplex PCR-based next-generation sequencing (NGS) to obtain the genome sequences of clinical HTNV in urine specimens containing ultra-low amounts of viral genomes. The epidemiological and phylogenetic analyses of HTNV demonstrated geographically homogenous clustering with those in Apodemus agrarius captured in highly endemic areas, indicating that phylogeographic tracing of HTNV genomes reveals the potential infection sites of patients with HFRS. Genetic exchange analyses showed a genetic configuration compatible with HTNV L segment exchange in nature.Conclusion/significanceOur results suggest that whole or partial genome sequences of HTNV from the urine enabled to track the putative infection sites of patients with HFRS by phylogeographically linking to the zoonotic HTNV from the reservoir host captured at endemic regions. This report raises awareness among physicians for the presence of HTNV in the urine of patients with HFRS.

The mechanical properties of Ti-6Al-4V alloy are affected by its microstructures. However, the effects of these microstructures on the high cycle fatigue behavior of Ti-6Al-4V alloy with a mixed structure (α + β phases) remain unknown. In this study, three alloy specimens were prepared using different hot-deformation methods, and their microstructures were investigated by optical microscopy and scanning electron microscopy. Fatigue tests were then performed to determine their high cycle fatigue and fatigue crack propagation behavior. All specimens showed a bimodal structure, but the morphology of each phase (e.g., diameter, shape, and volume fraction) showed notable differences. Among the samples prepared, the forged sample (FS) showed the lowest fatigue strength in all cycles. The fatigue strength of the homogeneously rolled sample (HS) was slightly higher than that of the rolled sample (RS) below 106 cycles but lower above 106 cycles. Compared with those of RS and HS, the secondary α (αs) grain width of FS was twofold larger. The interconnected primary α (αp) phase clusters in HS appeared to promote microcrack propagation.

Seoul virus (SEOV), an etiological agent for hemorrhagic fever with renal syndrome, poses a significant public health threat worldwide. This study evaluated the feasibility of a mobile Biomeme platform for facilitating rapid decision making of SEOV infection. A total of 27 Rattus norvegicus were collected from Seoul Metropolitan City and Gangwon Province in Republic of Korea (ROK), during 2016–2020. The serological and molecular prevalence of SEOV was 5/27 (18.5%) and 2/27 (7.4%), respectively. SEOV RNA was detected in multiple tissues of rodents using the Biomeme device, with differences in Ct values ranging from 0.6 to 2.1 cycles compared to a laboratory benchtop system. Using amplicon-based next-generation sequencing, whole-genome sequences of SEOV were acquired from lung tissues of Rn18-1 and Rn19-5 collected in Gangwon Province. Phylogenetic analysis showed a phylogeographical diversity of rat-borne orthohantavirus collected in Gangwon Province. We report a novel isolate of SEOV Rn19-5 from Gangwon Province. Our findings demonstrated that the Biomeme system can be applied for the molecular diagnosis of SEOV comparably to the laboratory-based platform. Whole-genome sequencing of SEOV revealed the phylogeographical diversity of orthohantavirus in the ROK. This study provides important insights into the field-deployable diagnostic assays and genetic diversity of orthohantaviruses for the rapid response to hantaviral outbreaks in the ROK.

When the uniformity of the magnetization yoke is low, a mismatch occurs between the physical rotation center and the center due to the magnetic force after magnetization. This discrepancy in rotation can cause issues such as vibration and noise during high-speed rotation, which in the long term leads to a decrease in the lifespan of the motor. In addition, in order to minimize the problem of motor lifespan when a vehicle is used for more than 10 years after purchase, the problems caused by magnetization should be solved as far as possible. In this study, magnetization yokes were designed in various ways to optimize the factors that affect the magnetic properties after the magnetization of the Nd2Fe14B permanent magnets used in electric motors. In the case of a 50 µm deviation between the coils wound inside the magnetization yoke, the magnetic property imbalance of the Nd2Fe14B magnets and the motor characteristics are not significantly affected after magnetization. However, when the center of the coil wound inside the yoke is shifted from the center of the yoke, the magnetic field is generated unevenly, which degrades both the magnetic and motor characteristics of the Nd2Fe14B magnet. Therefore, it is very important to control the center of the coil that generates the external magnetic field in the magnetized yoke in order to magnetize the Nd2Fe14B magnet with excellent magnetic properties.

BackgroundOrthohantaviruses, causing hemorrhagic fever with renal syndrome (HFRS) and hantavirus cardiopulmonary syndrome, pose a significant public health threat worldwide. Despite the significant mortality and morbidity, effective antiviral therapeutics for orthohantavirus infections are currently unavailable. This study aimed to investigate the prevalence of HFRS-associated orthohantaviruses and identify the etiological agent of orthohantavirus outbreaks in southern Republic of Korea (ROK).Methodology/principal findingsWe collected small mammals on Jeju Island during 2018-2020. We detected the Hantaan virus (HTNV)-specific antibodies and RNA using an indirect immunofluorescence assay test and reverse transcription-polymerase chain reaction on Apodemus agrarius chejuensis (A. chejuensis). The prevalence of anti-HTNV antibodies among rodents was 14.1%. A total of six seropositive mouse harbored HTNV RNA. The amplicon-based next-generation sequencing provided nearly full-length tripartite genomic sequences of six HTNV harbored by A. chejuensis. Phylogenetic and tanglegram analyses were conducted for inferring evolutionary relationships between orthohantaviruses with their reservoir hosts. Phylogenetic analysis showed a novel distinct HTNV genotype. The detected HTNV genomic sequences were phylogenetically related to a viral sequence derived from HFRS patient in southern ROK. Tanglegram analysis demonstrated the segregation of HTNV genotypes corresponding to Apodemus spp. divergence.Conclusions/significanceOur results suggest that A. chejuensis-borne HTNV may be a potential etiological agent of HFRS in southern ROK. Ancestral HTNV may infect A. chejuensis prior to geological isolation between the Korean peninsula and Jeju Island, supporting the co-evolution of orthohantaviruses and rodents. This study arises awareness among physicians for HFRS outbreaks in southern ROK.

Emerging and re-emerging RNA viruses pose significant public health, economic, and societal burdens. Hantaviruses (genus Orthohantavirus, family Hantaviridae, order Bunyavirales) are enveloped, negative-sense, single-stranded, tripartite RNA viruses that are emerging zoonotic pathogens harbored by small mammals such as rodents, bats, moles, and shrews. Orthohantavirus infections cause hemorrhagic fever with renal syndrome (HFRS) and hantavirus cardiopulmonary syndrome in humans (HCPS). Active targeted surveillance has elucidated high-resolution phylogeographic relationships between patient- and rodent-derived orthohantavirus genome sequences and identified the infection source by temporally and spatially tracking viral genomes. Active surveillance of patients with HFRS entails 1) recovering whole-genome sequences of Hantaan virus (HTNV) using amplicon (multiplex PCR-based) next-generation sequencing, 2) tracing the putative infection site of a patient by administering an epidemiological questionnaire, and 3) collecting HTNV-positive rodents using targeted rodent trapping. Moreover, viral genome tracking has been recently performed to rapidly and precisely characterize an outbreak from the emerging virus. Here, we reviewed genomic epidemiological and active surveillance data for determining the emergence of zoonotic RNA viruses based on viral genomic sequences obtained from patients and natural reservoirs. This review highlights the recent studies on tracking viral genomes for identifying and characterizing emerging viral outbreaks worldwide. We believe that active surveillance is an effective method for identifying rodent-borne orthohantavirus infection sites, and this report provides insights into disease mitigation and preparedness for managing emerging viral outbreaks.

The ability to accurately predict the early progression of hemorrhagic fever with renal syndrome (HFRS) is crucial for reducing morbidity and mortality rates in severely affected patients. However, the utility of biomarkers for predicting clinical outcomes remains elusive in HFRS. The aims of the current study were to analyze the serum levels of immune function-related proteins and identify novel biomarkers that may help ascertain clinical outcomes of HFRS. Enzyme-linked immunosorbent assay, Luminex, and bioanalyzer assays were used to quantitatively detect 15 biomarkers in 49 serum samples of 26 patients with HFRS. High hemoglobin (HGB) and low urine output (UO) levels were identified as potential biomarkers associated with the acute HFRS. The serum soluble urokinase plasminogen activator receptor (suPAR) and C-X-C motif chemokine ligand 10 (CXCL10) values increased in the early phase of diseases. Elevated suPAR, interleukin-10 (IL-10), CXCL10, and decreased transforming growth factor-beta 3 (TGF-β3) were representative predictors of the disease severity. Upregulation of the HGB showed a significant correlation with high levels of suPAR and CXCL10. Reduced UO positively correlated with increased suPAR, CXCL10, and TGF-β2, and decreased vascular endothelial growth factor and TGF-β3. The changing HGB and UO criteria, high suPAR, IL-10, CXCL10, and low TGF-β3 of HFRS raise significant awareness for physicians regarding prospective biomarkers for monitoring early warning signs of HFRS. This study provides critical insights into the clinical and immunological biomarkers for disease severity and progression in patients with HFRS to identify early predictions of fatal outcomes.

BackgroundHantaan orthohantavirus (Hantaan virus, HTNV), harbored by Apodemus agrarius (the striped field mouse), causes hemorrhagic fever with renal syndrome (HFRS) in humans. Viral genome-based surveillance at new expansion sites to identify HFRS risks plays a critical role in tracking the infection source of orthohantavirus outbreak. In the Republic of Korea (ROK), most studies demonstrated the serological prevalence and genetic diversity of orthohantaviruses collected from HFRS patients or rodents in Gyeonggi Province. Gangwon Province is a HFRS-endemic area with a high incidence of patients and prevalence of infected rodents, ROK. However, the continued epidemiology and surveillance of orthohantavirus remain to be investigated.Methodology/principal findingsWhole-genome sequencing of HTNV was accomplished in small mammals collected in Gangwon Province during 2015-2018 by multiplex PCR-based next-generation sequencing. To elucidate the geographic distribution and molecular diversity of viruses, we conducted phylogenetic analyses of HTNV tripartite genomes. We inferred the hybrid zone using cline analysis to estimate the geographic contact between two different HTNV lineages in the ROK. The graph incompatibility based reassortment finder performed reassortment analysis. A total of 12 HTNV genome sequences were completely obtained from A. agrarius newly collected in Gangwon Province. The phylogenetic and cline analyses demonstrated the genetic diversity and hybrid zone of HTNV in the ROK. Genetic exchange analysis suggested the possibility of reassortments in Cheorwon-gun, a highly HFRS-endemic area.Conclusions/significanceThe prevalence and distribution of HTNV in HFRS-endemic areas of Gangwon Province enhanced the phylogeographic map for orthohantavirus outbreak monitoring in ROK. This study revealed the hybrid zone reflecting the genetic diversity and evolutionary dynamics of HTNV circulating in Gangwon Province. The results arise awareness of rodent-borne orthohantavirus diseases for physicians in the endemic area of ROK.

Hepatitis A virus (HAV) is a serious threat to public health worldwide. We used multiplex polymerase chain reaction (PCR)-based next-generation sequencing (NGS) to derive information on viral genetic diversity and conduct precise phylogenetic analysis. Four HAV genome sequences were obtained using multiplex PCR-based NGS. HAV whole-genome sequence of one sample was obtained by conventional Sanger sequencing. The HAV strains demonstrated a geographic cluster with sub-genotype IA strains in the Republic of Korea. The phylogenetic pattern of HAV viral protein (VP) 3 region showed no phylogenetic conflict between the whole-genome and partial-genome sequences. The VP3 region in serum and stool samples showed sensitive detection of HAV with differences of quantification that did not exceed

The wear behavior of AISI304 stainless steel was investigated under dry, water-, and oil-lubricated conditions. A block-on-disk wear test was conducted in this work, since the test conditions could be controlled easily. For oil-lubricated contact, a significant amount of thin and elongated cutting chip-like debris was observed. This is attributed to the high lubricating effect of oil. Strain-induced martensitic (SIM) transformation was observed for all AISI304 blocks after the wear test, while AISI304 consisted of a single γ-austenite phase prior to the wear test. The Stribeck curve and the corresponding lubrication regimes were also considered to explain the wear behaviors and lubrication effect of AISI304. In comparison to the dry or water-lubricated conditions, which fall in the boundary lubrication regime at a low rotation speed, it is considered that the high viscosity of the oil-based lubricant causes the lubrication condition to enter the mixed lubrication regime early at a lower speed, thus reducing the specific wear rate over the 100–300 rpm range.

A metal matrix composite was developed through a unique liquid pressing infiltration process to study the wear mechanism of a TiC reinforced AISI 1020 steel matrix. The microstructure, hardness, and wear behaviors of the TiC/AISI 1020 composite were compared with commercial AISI 52100 bearing steel. Microstructural analysis showed that there were no defects, such as pores or agglomeration of reinforcement particles, and about 60% of the volume of TiC was uniformly dispersed. In the case of the AISI 52100 alloy, the hardness was 62.42 HRC, which was similar to the 62.84 HRC value of the as-cast TiC/AISI 1020 composite. After the quenching heat treatment, the Rockwell hardness of the composite increased to 76.64 HRC, which was attributed to the martensitic transformation of the AISI 1020 matrix. As a result of the pin-on-disc wear test with high contact pressure, the wear width of AISI 52100 was 2937 μm, which was approximately 4.3 times wider than that of the heat-treated metal matrix composite (682 μm). The wear depths of AISI 52100 and the heat-treated composite were 2.6 μm and 0.5 μm, respectively, indicating that TiC/AISI 1020 exhibited excellent wear resistance compared with bearing steel. Improved wear resistance of the TiC/AISI 1020 composite originates from uniformly distributed TiC, with an increase in the hardness due to the heat treatment.

Paramyxoviruses, negative-sense single-stranded RNA viruses, pose a critical threat to human public health. Currently, 78 species, 17 genera, and 4 subfamilies of paramyxoviruses are harbored by multiple natural reservoirs, including rodents, bats, birds, reptiles, and fish. Henipaviruses are critical zoonotic pathogens that cause severe acute respiratory distress and neurological diseases in humans. Using reverse transcription-polymerase chain reaction, 115 Crocidura species individuals were examined for the prevalence of paramyxovirus infections. Paramyxovirus RNA was observed in 26 (22.6%) shrews collected at five trapping sites, Republic of Korea. Herein, we report two genetically distinct novel paramyxoviruses (genus: Henipavirus): Gamak virus (GAKV) and Daeryong virus (DARV) isolated from C. lasiura and C. shantungensis, respectively. Two GAKVs and one DARV were nearly completely sequenced using next-generation sequencing. GAKV and DARV contain six genes (3′-N-P-M-F-G-L-5′) with genome sizes of 18,460 nucleotides and 19,471 nucleotides, respectively. The phylogenetic inference demonstrated that GAKV and DARV form independent genetic lineages of Henipavirus in Crocidura species. GAKV-infected human lung epithelial cells elicited the induction of type I/III interferons, interferon-stimulated genes, and proinflammatory cytokines. In conclusion, this study contributes further understandings of the molecular prevalence, genetic characteristics and diversity, and zoonotic potential of novel paramyxoviruses in shrews.

In this study, to evaluate the effect of boron carbide (B4C) addition on the wear performance of aluminum (Al), Al6061 and 5, 10, and 20 vol.% B4C/Al6061 composites were manufactured using the stir casting and hot rolling processes. B4C particles were randomly dispersed during the stir casting process; then, B4C particles were arranged in the rolling direction using a hot rolling process to further improve the B4C dispersion and wear resistance of the composites. Furthermore, a continuous interfacial layer between B4C and the Al6061 matrix was generated by diffusion of titanium (Ti) and chromium (Cr) atoms contained in the Al6061 alloy. Wear depth and width of the composites decreased with increasing B4C content. Furthermore, with B4C addition, coefficient of friction (COF) improved as compared with that of Al6061. The results indicate that interface-controlled, well-aligned B4C particles in the friction direction can effectively increase the wear properties of Al alloys and improve their hardness.

Abstract Although surgery and radiation are beneficial for treating cancer, they can also lead to malfunctions of the lymphatic system such as secondary lymphedema. This abnormality of the lymphatic system is characterized by severe swelling, adipogenesis, inflammation, and fibrosis in the lymphedematous region. Moreover, the proliferation of fibrotic tissue in the lymphedematous region generates edema that is no longer spontaneously reversible. No treatment for fibrosis has been validated in patients with lymphedema. In our efforts to develop a therapeutic agent for lymphedema fibrosis, we used a newly established mouse hind limb model. Previous studies have demonstrated that hyaluronic acid accumulates in the lymphedematous region. Thus, we challenged mice with of hyaluronidase (HYAL), with the aim of reducing fibrogenesis. After subcutaneous injections in the lymphedematous mouse leg every two days, the volume of lymphedema had reduced significantly by 7 days post-operation. Histochemical analysis indicated that collagen accumulation and myofibroblast differentiation were decreased in epidermal tissues after HYAL injection. Moreover, it was associated with upregulation of interferon-gamma, increased numbers of Th1 cells, and downregulation of interleukin-4 and interleukin-6 in the lymphedematous region and spleen. These results indicate that hydrolysis of hyaluronic acid can boost an anti-fibrotic immune response in the mouse lymphedema model.

Whole-genome sequencing of infectious agents enables the identification and characterization of emerging viruses. The MinION device is a portable sequencer that allows real-time sequencing in fields or hospitals. Hantaan orthohantavirus (Hantaan virus, HTNV), harbored by Apodemus agrarius, causes hemorrhagic fever with renal syndrome (HFRS) and poses a critical public health threat worldwide. In this study, we aimed to evaluate the feasibility of using nanopore sequencing for whole-genome sequencing of HTNV from samples having different viral copy numbers. Amplicon-based next-generation sequencing was performed in A. agrarius lung tissues collected from the Republic of Korea. Genomic sequences of HTNV were analyzed based on the viral RNA copy numbers. Amplicon-based nanopore sequencing provided nearly full-length genomic sequences of HTNV and showed sufficient read depth for phylogenetic analysis after 8 h of sequencing. The average identity of the HTNV genome sequences for the nanopore sequencer compared to those of generated from Illumina MiSeq revealed 99.8% (L and M segments) and 99.7% (S segment) identities, respectively. This study highlights the potential of the portable nanopore sequencer for rapid generation of accurate genomic sequences of HTNV for quicker decision making in point-of-care testing of HFRS patients during a hantavirus outbreak.

The virus behind the current pandemic, severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) is responsible for the etiology of novel coronavirus disease (COVID-19) and poses a critical public health threat worldwide. Effective therapeutics and vaccines against multiple coronaviruses remain unavailable. Single-chain variable fragment (scFv), a recombinant antibody, exhibits broad-spectrum antiviral activity against DNA and RNA viruses owing to its nucleic acid-hydrolyzing property. The antiviral activity of 3D8 scFv against SARS-CoV-2 and other coronaviruses was evaluated in Vero E6 cell cultures. Viral growth was quantified with quantitative RT-qPCR and plaque assay. The nucleic acid-hydrolyzing activity of 3D8 was assessed through abzyme assays of in vitro viral transcripts and cell viability was determined by MTT assay. We found that 3D8 inhibited the replication of SARS-CoV-2, human coronavirus OC43 (HCoV-OC43), and porcine epidemic diarrhea virus (PEDV). Our results revealed the prophylactic and therapeutic effects of 3D8 scFv against SARS-CoV-2 in Vero E6 cells. Immunoblot and plaque assays showed the reduction of coronavirus nucleoproteins and infectious particles, respectively, in 3D8 scFv-treated cells. These data demonstrate the broad-spectrum antiviral activity of 3D8 against SARS-CoV-2 and other coronaviruses. Thus, it could be considered a potential antiviral countermeasure against SARS-CoV-2 and zoonotic coronaviruses.

An epidemiological investigation was conducted for a scrub typhus case reported in a U.S. Forces Korea military patient in the Republic of Korea in November 2018. The patient had a fever, maculopapular rash, and an eschar. The full-length sequence of Orientia tsutsugamushi 56-kDa type-specific antigen (TSA) gene was obtained from eschar tissue by multiplex PCR-based Next Generation Sequencing for genetic identification. Based on the 56-kDa TSA gene, the O. tsutsugamushi aligned most closely with the Boryong strain.

In this study, to fabricate neutron shielding material, boron carbide (B4C)-reinforced aluminum (Al) alloy composites were successfully fabricated by stir casting followed by a hot rolling process. Microstructural analysis of B4C/Al6061 composites with different volume fractions (5, 10, 20, 25, and 30%) revealed that the composites had volume ratios similar to the target volume ratios of B4C. Furthermore, B4C reinforcements were uniformly dispersed in the Al matrix, forming multi-interfacial layers of Al4C3/(Ti,Cr)B2. The interfacial layer generated during stir casting maintained its own structure after the hot rolling process, indicating strong interfacial bonding strength. The tensile strengths of the B4C/Al6061 composites increased to 20 vol.% and stayed above the value for Al6061, even reaching 30 vol.%. The measured thermal neutron shielding rate increased with increasing B4C content, and the highest thermal neutron shielding rate was observed at 30 vol.% composite, which corresponds to 95.6% neutron shielding at 0.158-cm thickness.

In this study, different volume fractions of silicon-carbide-reinforced AA2024 matrix composites were successfully fabricated using stir-casting (SC) and die-casting (DC) processes. The microstructural difference and physical properties of the composites during the manufacturing process were investigated in detail. The microstructural analysis found that the composite produced by the SC process had some reinforcement clusters and pores; however, defects and clusters significantly decreased after the DC process. In particular, the degree of reinforcement dispersion was quantitatively analyzed and compared before and after the DC process using the dispersion-analysis method. As a result of quantitative evaluation, the degree of dispersion was improved 2.5, 4.6, and 4.0 times with 3 vol.%, 6 vol.%, and 9 vol.% SiC-reinforced composite after the DC process, respectively. The electron backscatter diffraction (EBSD) analysis showed that the grain size of the 9 vol.% SiC-reinforced DC composite (17.67 μm) was 75% smaller than that of the SC composite (68.06 μm). The average tensile strength and hardness of the 9 vol.% SiC-reinforced DC composite were 2 times higher than those of the AA2024 matrix. The superior mechanical properties of the DC-processed composite can be attributed to the increase in dispersivity of the SiC particles and to decreases in defects and grain size during the DC process.

For developing subminiature and highly integrated multilayer inductors, soft magnetic powder was used; however, its ferrite magnetic component is characterized by high resistivity and reduced direct current saturation, leading to the deterioration of the inductor under high currents. Therefore, herein, to improve the electromagnetic properties of thin-film inductors, Fe nanopowder was used to increase the volume fraction of magnetic sheets. Surface treatment was performed by using silane coupling agents, which improved the bonding strength and dispersibility of the Fe nanopowder with a heterogeneous epoxy binder. For uniform surface treatment on the nanopowder, the silane-treated powder was aged for 24 h, at a temperature of 3 °C. The surface-treated Fe nanopowder was used with a mixing ratio of the soft magnetic powder (coarse:fine:nano) of 7:2.5:0.5 wt.%; this was successful in producing a flexible and highly densified magnetic sheet. As a result, the volume fraction of the magnetic sheet for thin-film inductors to which a low-temperature aging-treated nanopowder was applied was significantly improved.

This study was conducted on titanium diboride (TiB2) reinforced Al metal matrix composites (MMCs) with improved properties using a TiB2 and aluminum (Al) 1050 alloy. Al composites reinforced with fine TiB2 at volume ratios of more than 60% were successfully fabricated via the liquid pressing infiltration (LPI) process, which can be used to apply gas pressure at a high temperature. The microstructure of the TiB2–Al composite fabricated at 1000 °C with pressurization of 10 bar for 1 h showed that molten Al effectively infiltrated into the high volume-fraction TiB2 preform due to the improved wettability and external gas pressurization. In addition, the interface of TiB2 and Al not only had no cracks or pores but also had no brittle intermetallic compounds. In conclusion, TiB2–Al composite, which has a sound microstructure without defects, has improved mechanical properties, such as hardness and strength, due to effective load transfer from the Al matrix to the fine TiB2 reinforcement.

The antiviral effect of a catalytic RNA-hydrolyzing antibody, 3D8 scFv, for intranasal administration against avian influenza virus (H1N1) was described. The recombinant 3D8 scFv protein prevented BALB/c mice against H1N1 influenza virus infection by degradation of the viral RNA genome through its intrinsic RNA-hydrolyzing activity. Intranasal administration of 3D8 scFv (50 μg/day) for five days prior to infection demonstrated an antiviral activity (70% survival) against H1N1 infection. The antiviral ability of 3D8 scFv to penetrate into epithelial cells from bronchial cavity via the respiratory mucosal layer was confirmed by immunohistochemistry, qRT-PCR, and histopathological examination. The antiviral activity of 3D8 scFv against H1N1 virus infection was not due to host immune cytokines or chemokines, but rather to direct antiviral RNA-hydrolyzing activity of 3D8 scFv against the viral RNA genome. Taken together, our results suggest that the RNase activity of 3D8 scFv, coupled with its ability to penetrate epithelial cells through the respiratory mucosal layer, directly prevents H1N1 virus infection in a mouse model system.

Aluminum alloy (Al7075) composites reinforced with a high volume fraction of silicon carbide (SiC) were produced by a liquid-pressing process. The characterization of their microstructure showed that SiC particles corresponding to a volume fraction greater than 60% were uniformly distributed in the composite, and Mg2Si precipitates were present at the interface between the matrix and the reinforcement. A superior compressive strength (1130 MPa) was obtained by an effective load transfer to the hard ceramic particles. After solution heat treatment and artificial aging, the Mg2Si precipitates decomposed from rod-shaped large particles to smaller spherical particles, which led to an increase of the compressive strength by more than 200 MPa. The strengthening mechanism is discussed on the basis of the observed microstructural evolution.

In this study, high volume fraction B4C reinforced Al matrix composites were fabricated with a liquid pressing process. Microstructural analysis by scanning electron microscope and a transmission electron microscopy shows a uniform distribution of the B4C reinforcement in the matrix, without any defects such as pore and unwanted reaction products. The compressive strength and wear properties of the Al7075 matrix and the composite were compared at room temperature, 100, 200, and 300 °C, respectively. The B4C reinforced composite showed a very high ultimate compression strength (UCS) over 1.4 GPa at room temperature. The UCS gradually decreased as the temperature was increased, and the UCS of the composite at 300 °C was about one third of the UCS of the composite at room temperature. The fractography of the compressive test specimen revealed that the fracture mechanism of the composites was the brittle fracture mode at room temperature during the compression test. However, at the elevated temperature, AMCs had a mixed mode of a brittle and ductile fracture mechanism under the compressive load. The composite produced by a liquid pressing process also showed superior wear resistance compared with the Al matrix. The result of the wear test indicates that the wear loss of the Al matrix at 300 °C was two times higher than that of the AMCs, which is attributed to the formation of a mechanically mixed layer (MML) in the composites at the high temperature.

Aluminum (Al)-stainless steel 316L (SUS316L) composites were successfully fabricated by the spark plasma sintering process (SPS) using pure Al and SUS316L powders as raw materials. The Al-SUS316L composite powder comprising Al with 50 vol.% of SUS316L was prepared by a ball milling process. Subsequently, it was sintered at 630 °C at a pressure of 200 MPa and held for 5 min in a semisolid state. The X-ray diffraction (XRD) patterns show that intermetallic compounds such as Al13Fe4 and AlFe3 were created in the Al-SUS316L composite because the Al and SUS316L particles reacted together during the SPS process. The presence of these intermetallic compounds was also confirmed by using XRD, scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), and EDS mapping. The mechanical hardness of the Al-SUS316L composites was analyzed by a Vickers hardness tester. Surprisingly, the Al-SU316L composite exhibited a Vickers hardness of about 620 HV. It can be concluded that the Al-SUS316L composites fabricated by the SPS process are lightweight and high-hardness materials that could be applied in the engineering industry such as in automobiles, aerospace, and shipbuilding.

Aluminium–copper composite materials were successfully fabricated using spark plasma sintering with Al and Cu powders as the raw materials. Al–Cu composite powders were fabricated through a ball milling process, and the effect of the Cu content was investigated. Composite materials composed of Al–20Cu, Al–50Cu, and Al–80Cu (vol.%) were sintered by a spark plasma sintering process, which was carried out at 520 °C and 50 MPa for 5 min. The phase analysis of the composite materials by X-ray diffraction (XRD) and energy-dispersive spectroscopy (EDS) indicated that intermetallic compounds (IC) such as CuAl2 and Cu9Al4 were formed through reactions between Cu and Al during the spark plasma sintering process. The mechanical properties of the composites were analysed using a Vickers hardness tester. The Al–50Cu composite had a hardness of approximately 151 HV, which is higher than that of the other composites. The thermal conductivity of the composite materials was measured by laser flash analysis, and the highest value was obtained for the Al–80Cu composite material. This suggests that the Cu content affects physical properties of the Al–Cu composite material as well as the amount of intermetallic compounds formed in the composite material.

In this study, we have attempted to manufacture functionally graded materials (FGMs) using aluminum alloys 3003 and 6063 via a hot extrusion process to realize multifunctionality through achieving high strength and low weight. The FGMs were fabricated using Al3003 powder and Al6063 bulk to improve the interfacial properties. Particle size analysis and X-ray fluorescence of the Al3003 powder were used to analyze the composition of general Al3003; microstructure analysis revealed improved hardness with almost no defects, such as cracks at the interface between the two materials. The experimentally determined tensile strength of the composite was observed to be higher than the theoretical value calculated using the rule of mixtures; the strengthening mechanisms considered for the calculations were grain size reduction and precipitation hardening. In particular, we attempted to predict the strengthening effect resulting from the fine grain size of the powder and grain size reduction due to the extrusion process using the Hall⁻Petch equation. The Kelly⁻Tyson equation was also used to calculate the theoretical strength in the presence of the strengthening phases. Based on these results, it was confirmed that FGMs can be successfully produced using the hot extrusion process.

In this research, we successfully fabricate high-hardness and lightweight Al-Ti composites. Al-Ti composites powders with three compositions (Al-20, 50, and 80 vol.% Ti) are mixed using ball milling and subsequently subjected to spark plasma sintering (SPS). The microstructures and phases of the Al-Ti composites are characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD) spectroscopy, and field emission-electron probe microanalysis (FE-EPMA). These tests confirm the presence of several intermetallic compounds (ICs) (Al3Ti, Al5Ti2, Al11Ti5) in the composites, and we are able to confirm that these ICs are produced by the reaction of Al and Ti during the SPS process. Furthermore, thermogravimetric-differential thermal analysis (TG-DTA) is used to analyze the formation behavior of the ICs. In addition, the mechanical properties of the composites are measured using their Vickers hardness and it is observed that the Al-80 vol.% Ti composite exhibits the highest hardness. Consequently, it is assumed that SPS is suitable for fabricating Al-Ti composites which represent the next-generation materials to be used in various industrial fields as high-hardness and lightweight materials.

A novel Fe-Co binary hollow fiber was synthesized by electroless plating using hydrolyzed polyester fiber and its anisotropy characteristic was investigated for electromagnetic wave absorbing materials. The hollow fibers in parallel with magnetic field show higher saturated magnetization of 202 emu/g at the applied magnetic field of 10 kOe and lower coercivity (27.658 Oe), compared with the random and vertical oriented hollow fibers. From complex permittivity measurement, the Fe-Co hollow fiber composites clearly display a single dielectric resonance, located at ∼14 GHz. The Fe-Co hollow fibers not only provide excellent EM properties in GHz frequency ranges, resulting mainly from the strong resonance, but also adjust the soft magnetic properties through fiber alignments. The cavitary structure of the Fe-Co hollow fibers, not only giving rise to a dielectric loss resonance and also adjusting its peak frequency, may be a pathway to useful EM wave absorptive devices in GHz frequency ranges.

Viral protein neutralizing antibodies have been developed but they are limited only to the targeted virus and are often susceptible to antigenic drift. Here, we present an alternative strategy for creating virus-resistant cells and animals by ectopic expression of a nucleic acid hydrolyzing catalytic 3D8 single chain variable fragment (scFv), which has both DNase and RNase activities. HeLa cells (SCH07072) [corrected] expressing 3D8 scFv acquired significant resistance to DNA viruses. Virus challenging with Herpes simplex virus (HSV) in 3D8 scFv transgenic cells and fluorescence resonance energy transfer (FRET) assay based on direct DNA cleavage analysis revealed that the induced resistance in HeLa cells was acquired by the nucleic acid hydrolyzing catalytic activity of 3D8 scFv. In addition, pseudorabies virus (PRV) infection in WT C57BL/6 mice was lethal, whereas transgenic mice (STG90) that expressed high levels of 3D8 scFv mRNA in liver, muscle, and brain showed a 56% survival rate 5 days after PRV intramuscular infection. The antiviral effects against DNA viruses conferred by 3D8 scFv expression in HeLa cells as well as an in vivo mouse system can be attributed to the nuclease activity that inhibits viral genome DNA replication in the nucleus and/or viral mRNA translation in the cytoplasm. Our results demonstrate that the nucleic-acid hydrolyzing activity of 3D8 scFv confers viral resistance to DNA viruses in vitro in HeLa cells and in an in vivo mouse system.