Search

Abstract—The National Aeronautics and Space Administration (NASA) is presently embarking on the implementation of far-reaching changes within the framework of both space and aeronautics communications architectures. For example, near earth relays are looking to transition from the traditional few large geostationary satellites to satellite constellations consisting of thousands of small low earth orbiting satellites while lunar space communications will require the need to relay data from many assets distributed on the lunar surface back to earth. Furthermore, within the aeronautics realm, satellite communications for beyond line of sight (BLOS) links are being investigated in tandem with the proliferation of unmanned aerial systems (UAS) within the urban air mobility (UAM) environment. In all of these scenarios, future communications architectures will demand the need to connect and quickly transition between many nodes for large data volume transport. As such, NASA Glenn Research Center (GRC) has been heavily investigating the development of low cost phased array technologies that can readily address these various scenario conditions. In particular, GRC is presently exploring 5G-based beamformer technologies to leverage commercial timescale and volume production cycles which have heretofore not existed within the frequency allocations utilized for NASA applications. In this paper, an overview of the potential future applications of phased arrays being envisioned by NASA are discussed, along with technology feasibility demonstrations being conducted by GRC implementing low cost, 5G based beamformer technologies.

This project developed an antenna to enable beyond line of sight (BLOS) command and control for small UAVs. We took advantage of a newly assigned provisional Ku-band spectrum for UAVs and used unique antenna design to avoid interference with ground systems. This required the design of an antenna with high isotropic effective radiated power (EIRP) and ultra-low sidelobes. The antenna was made with polymer aerogel as a substrate to both reduce weight and improve performance, as demonstrated in an Aero Seedling. In addition, designing the antennas to be conformal to the aircraft fuselage will reduce drag.

This paper introduces the new Portable Laser Guided Robotic antenna range (PLGR) at the National Aeronautics and Space Administration's (NASA) Glenn Research Center. Previous work used industrial robots in fixed facilities to characterize antennas and required fixtures that do not lend themselves to portable applications.NASA's PLGR system is designed for in-situ antenna measurements at a remote site. The system consists of a robot arm mounted on a vertical lift and a laser tracker, each on a portable base. The lift and laser tracker enable scanning a surface larger than the robot's reach. To accomplish this the robot first collects all points within its reach, then the system is moved and the laser tracker is used to relocate the robot before additional points are captured.The PLGR architecture will be discussed including how safety systems and path planning are combined to effectively characterize antennas. Software was written in high level languages for flexible integration of vector network analyzers and antenna controllers. Lastly, data will be shown to demonstrate the system functionality and accuracy.

This paper introduces the new Portable Laser Guided Robotic Metrology (PLGRM) system at the National Aeronautics and Space Administration's (NASA) Glenn Research Center. Previous work used industrial robots in fixed facilities to characterize antennas and required fixtures that do not lend themselves to portable applications. NASA's PLGRM system is designed for in-situ antenna measurements at a remote site.The system consists of a collaborative robot arm mounted on a vertical lift and a laser tracker, each on a mobile base. Together,they enable scanning a surface larger than the robot's reach.To accomplish this, the robot first collects all points within its reach, then the system is moved and the laser tracker is used to relocate the robot before additional points are captured. The PLGRM implementation will be discussed including how safety and planning are combined to effectively characterize antennas.Software defined triggering is a feature, for flexible integration of vector network analyzers and antenna controllers. Lastly, data will be shown to demonstrate system functionality and accuracy.

Mobile and embedded applications are emerging in the growing field of free space optical links (FSOL). Some mobile applications for FSOL include spacecraft, aircraft, and automotive. These applications by nature require low size weight and power (SWaP) solutions. The main challenge with any FSOL system is the strict pointing requirements. Common solutions to pointing and alignment of FSOL include gimbals, fast steering mirrors, and adaptive optics. All of which provide viable solutions at the cost of increased SWaP. Previously, we presented the use of both large core fibers and double clad fibers (DCF) to interface FSOL transmit and receive optics with small form factor pluggable optical transceivers (SFP). Double clad fibers have been shown to enable a common optical path by transmitting through a single mode core and receiving through a large inner cladding. This enables a single set of symmetric transmit and receive optics, which decreases the SWaP. In addition, using DCF increases the received power stability of the link relative to a multi-mode fiber (MMF) transmitting. To determine the viability of the system, bit error rate performance needs to be investigated. The results of this paper show that at a bit rate of 10 Gbps, double clad fibers offer similar bit error rate performance to single mode fibers when transmitting and multi-mode fibers when receiving enabling a symmetric duplex FSOL reducing SWaP.

The growing demand for Unmanned Aerial Systems (UAS) operating beyond the line of sight (BLOS) has resulted in an increased interest in using existing commercial satellite communication capabilities for UAS command and control (C2) communications. The World Radiocommunication Conference in 2015 designated portions of Ku-Band and Ka-Band fixed satellite service (FSS) spectrum to support UAS C2 communications, provided that potential interference with existing co-allocated users in these bands is addressed. As the user base in this new spectrum allocation expands, there is an increased potential for interference with existing terrestrial communication systems operating under fixed service (FS) allocations. The portion of Ka-Band spectrum allocated for UAS C2 avoids significant interference issues, but the Ku-Band allocation contains a co-primary FS allocation, creating potential interference problems. Therefore, UAS must identify solutions to avoid interfering with these existing FS ground sites while maintaining good links with satellite constellations. UAS operating with conventional fixed feed parabolic antennas will have difficulty in meeting interference thresholds, especially at high latitudes where the antennas will operate with low elevation angles. As a means of addressing this limitation, NASA is investigating the use of a phased array antenna to enable mitigation of interference into ground-based FS receivers. In this paper, a novel lightweight conformal phased array antenna will be presented that can use null-steering and/or beam shaping to avoid ground interference while simultaneously providing strong satellite microwave links for communications. The reduced weight of this design and ability to integrate into the fuselage of smaller UAS platforms will also be discussed as a potential solution to provide BLOS operation via spectrum sharing for an expanding user base. This presentation will review design aspects of the conformal phased array antenna, describe the intended benefits in reducing interference with FS ground stations, and describe phased array development and test plans.

Bidirectional, high data rate, low size, weight, and power (SWaP), and low cost free space optical links are needed for space communication applications to send and receive large volumes of data. We are exploring design strategies for optical transceivers to reduce SWaP and cost through increased misalignment tolerance (pointing requirement reduction) and sharing the optical transmit and receive paths (imposing optical symmetry). In applications where the detector is fiber coupled, the fiber numerical aperture is the main driver of the pointing accuracy requirement. Unfortunately, reducing the pointing requirement by increasing the fiber numerical aperture symmetrically causes instability in received power over small environmental changes. This paper explores double clad fibers as a solution to both reduce the power instability and increase the pointing accuracy tolerance. Double clad fibers can transmit a Gaussian beam from a single mode fiber and receive in a multi-mode aperture. Results show that double clad fiber have an improved misalignment tolerance and a higher stability for small changes in temperature when compared to single mode fibers and multimode fibers. Also, double clad fibers are shown to match the performance of an asymmetrical link design with a single mode transmit fiber and a multimode receive fiber.

In an effort to construct an optical transceiver for supporting multi-point communication, researchers developed large field-of-view FSO transceivers with wide apertures for facilitating rapid acquisition and optical signal tracking. The design is constructed from fiber-bundle(s) intelligently arranged to provide multiple optical pathways within a single transceiver, with each pathway limited to a particular optical directionality. Because designs with wide apertures are susceptible to receiving several optical signals simultaneously from multiple transmitters, accurately decoding individual signals and achieving true multi-user communication can be difficult. The work detailed in this paper investigated the use of blind source separation techniques, mainly independent component analysis (ICA), to estimate transmitted signals from their observed, combined mixtures sans information. Effects of signal power, format, data rate, wavelength, and turbulence severity on signal separation, as well as signal demodulation accuracy was also analyzed using experimental optical signals and corresponding mixtures. Signal generators, laser sources, turbulence emulator, beam profiler, photodiodes, and oscilloscopes comprised the experiment setup. Optical signals with varying power, format, and wavelength were generated and propagated through turbulence with varying degree severity, and finally received by the fiber-bundle-based optical transceiver. Results demonstrate that an ICA technique can accurately process the combined signals into corresponding individual components. The investigation further identified signal characteristics (e.g., power levels, format, data rate) and turbulence severity under which ICA is unable to accurately perform signal separations.

FSO (Free-Space Optical)-based communication systems experience difficulty with receiving and separating signals arising from multiple transmitters, a capability that would facilitate implementation of MIMO (Multiple-In, Multiple-Out) systems. Current implementations require multiple, distinct optical antennas, each tracking a single user, which proves bulky and costly, especially if the transmitters are moving and must be tracked. A fiber-bundle receiver has the potential to use multiple pathways, corresponding to the individual fibers within the receiver, to capture different combinations of the incoming optical signals. If the bundle provides linear combining of the optical signals from both the individual fibers in the bundle and amongst the incoming optical signals, signal processing could extract the individual signals from the combinations. In this paper, we experimentally investigate whether the fiber-bundle receiver possesses sufficient linearity of operation to allow the separation of two signals by simple processing algorithms, for both turbulent and non-turbulent conditions. Data from two distinct sources enters a single-bundle, single field of view receiver, and a basis signal from one transmitter provides the reference for performing simple subtraction-based extraction of the unknown signal from the other transmitter. The experimental results show that the receiver does operate linearly, and that the linear operation remains sufficiently intact in the presence of turbulence to extract a recognizable copy of one signal from the other. The ability of the fiber bundle receiver to mitigate turbulence effects appears to assist in maintaining this sufficient level of linearity.

The Integrated Radio and Optical Communications (iROC) project at the National Aeronautics and Space Administration (NASA) is investigating the merits of a hybrid radio frequency (RF) and optical communication system for deep space missions. In an effort to demonstrate the feasibility and advantages of a hybrid RF/Optical software defined radio (SDR), a laboratory prototype was assembled from primarily commercial-off-the-shelf (COTS) hardware components. This COTS platform has been used to demonstrate simultaneous transmission of the radio and optical communications waveforms through to the physical layer (telescope and antenna). This paper details the hardware and software used in the platform and various measures of its performance. A laboratory optical receiver platform has also been assembled in order to demonstrate hybrid free space links in combination with the transmitter.

The Integrated Radio and Optical Communications (iROC) project at the National Aeronautics and Space Administration (NASA) is investigating the merits of a hybrid radio frequency (RF) and optical communication system for deep space missions. In an effort to demonstrate the feasibility and advantages of a hybrid RFOptical software defined radio (SDR), a laboratory prototype was assembled from primarily commercial-off-the-shelf (COTS) hardware components. This COTS platform has been used to demonstrate simultaneous transmission of the radio and optical communications waveforms through to the physical layer (telescope and antenna). This paper details the hardware and software used in the platform and various measures of its performance. A laboratory optical receiver platform has also been assembled in order to demonstrate hybrid free space links in combination with the transmitter.