Search

Houses are the places where people spend most of their time. That is why indoor air quality at home is essential for public health. Sufficient ventilation is the factor to avoid accumulation of pollutants in indoor air, which include microorganisms, such as SARS-CoV-2. Therefore, adequate ventilation is needed to provide good indoor air quality for human health and reduce infection risk at home. There are no reports of residential ventilation rates in Turkey. In this study, CO2 concentrations were measured in two residences in Izmir, Turkey. Three experiments were conducted to determine background concentrations and the rate of natural ventilation with infiltration and opening windows. Results show that air exchange provided by infiltration is low for both case rooms, while adequate ventilation could be achieved with natural ventilation under the studied conditions. Infiltration provided air exchange and ventilation rates of 0.18 h-1 and 5.9 m3/h for Case 1 and 0.29 h-1 and 8.23 m3/h for Case 2, respectively. Air exchange and ventilation rates were increased to 2.36 h-1 and 76.9 m3/h for Case 1 and 1.2 h-1 and 34 m3/h for Case 2, respectively, by opening the windows. Although ventilation can be provided by opening the windows, the other factors that determine its rate, e.g., meteorological variables, cannot be controlled by the occupants. Consequently, people cannot ensure the good indoor air quality in bedrooms and sufficient reduction in transmission of pathogenic microorganisms; therefore, risk of spreading diseases such as COVID-19 at home.

Household cleaning products are sources of volatile organic compounds (VOCs). Bleach containing products are a special case because reactions occur between chloride and their organic content such as surfactants, perfumes, etc., generating VOCs. This study aimed to determine concentration of 13 VOCs in bleach-containing automatic toilet cleaners, to estimate their indoor air concentrations and associated exposure and health risk levels. Experiments with products purchased from supermarkets were conducted in 20-mL headspace vials by placing 1 g of sample with and without water. Solid-phase micro extraction with a DVB/CAR/PDMS fiber assembly was used for adsorption of VOCs from the headspace, and analyzed using a GC-MS. The median carbon tetrachloride and chloroform concentrations of the studied products ranged from 5.03 × 10−3 to 2.37 × 10−2 μg/g and 2.53 × 10−2 to 2.37 μg/g, respectively. The modeled 95th percentile indoor air concentrations in a 1.6 m3 bathroom with no ventilation were estimated to be 1 and 20 μg/m3 for carbon tetrachloride and chloroform, respectively. The 95th percentile carcinogenic risk associated even with the use of the highest content product, 3.72 × 10−7 and 8.62 × 10−7 for carbon tetrachloride and chloroform respectively, were below the acceptable risk. In conclusion, automatic toilet-bowl cleaners were found to be sources of VOCs, but their emission potentials are not high to cause considerable indoor air concentrations over their suggested product lifetime. In turn, carcinogenic risks associated with inhalation exposure are below the de Minimis risk level of 10−6.

Abstract In this study, Wood Plastic Composites (WPCs) were produced from post-consumer bulky wastes of recycled plastic and wood in order to minimize waste, decrease environmental effects of plastics, reserve natural resources, and support circular economy for sustainable production and consumption. Five different types of polypropylene (PP) or polyethylene (PE) based recycled plastics and wood obtained from urban household bulky wastes were used in the production of recycled WPC composites, r-WPCs. Virgin WPC (v-WPC) and r-WPC compounds were prepared with wood flour (WF) and maleic anhydride grafted compatibilizer (MAPP or MAPE) to evaluate the effect of recycled polymer type and compatibilizer on the mechanical properties. It was found that tensile strength properties of r-WPCs produced from recycled PP (r-PP) were higher than that of the r-WPCs produced from mixed polyolefins and recycled PE. r-WPCs containing anti-oxidants, UV stabilizers, and compatibilizer with different WF compositions were produced from only recycled garden fraction PP (PPFGF) to determine the optimum composition and processing temperature for pilot scale manufacturing of r-WPCs. Based on tensile, impact, flexural, and water sorption properties of r-WPC compounds with different formulations, the optimum conditions of r-WPC compounds for industrial manufacturing process were determined. Surface morphology of fractured surfaces as well as tensile, flexural and density results of r-WPC compounds revealed the enhancement effect of MAPP on interfacial adhesion in r-WPCs. r-WPC products (crates and table/chair legs) based on bulky wastes were produced using an injection molding process at industrial scale by using 30 wt% WF-filled r-WPC compound. This study demonstrated that r-WPC compounds from recycled bulky plastic and wood wastes can be used as a potential raw material in plastic as well as WPC industry, contributing to circular economy. Graphic Abstract

Natural arsenic contamination is a critical problem for various places around the world. Simav Plain (Kutahya, Turkey) is one such area that was shown to have natural arsenic contamination in its waters and soils. Arsenic exposure through ingestion of edible crops cultivated in Simav Plain and associated health risks were assessed in this study. To achieve this objective, arsenic levels in 18 crop species were estimated based on measured soil arsenic concentrations. Individual and aggregate non-carcinogenic and carcinogenic risks associated with ingestion of arsenic-contaminated crops were then assessed with scenario-based deterministic point estimates and stochastic population estimates. Monte Carlo simulation was used for the estimation of population health risks. Accordingly, wheat was found as the highest-ranked crop specie for the both types of health risks, followed by tomato and potato, which are three of the most consumed crops in the region. The risk levels estimated in this study were relatively high, indicating consumption of crops grown in the plain may be posing significant health risks even at lower-bound estimates. Consuming wheat, tomato, potato, and their products from uncontaminated sources was found to reduce the aggregate risks up to 88% implicating the importance of proposing suitable management measures for similar risk-prone areas.

Cumulative health risk estimation for exposure to mixtures is a current issue, which would present a useful tool for environmental and public health management. Cumulative risks were estimated with response and dose addition methods for individual multi-route - multi-pathway exposure to trihalomethanes and associated carcinogenic toxic risks in Izmir, Turkey. Exposure levels were estimated for ingestion, dermal, and inhalation routes using measured tap water and bottled water THM concentrations. Drinking, showering, hand and dish washing were the considered pathways. THM concentrations in air during the showering were modeled with two-resistance theory using tap water concentration data. The estimated carcinogenic risk levels for ingestion route were in the range of safe (< 10(-6)) to low priority (< 10(-4)), for dermal route all were in the safe zone (< 10(-6)), and for inhalation route were in the range of safe to high priority (> 10(-4)) zones, indicating ingestion and inhalation routes were of similar significance ahead of dermal exposure. Cumulative carcinogenic risks of THM compounds were estimated using simple (response) addition and dose addition using cumulative relative potency factor (CRPF) methods. CRPF method estimated the risks at lower levels compared to the simple addition, which originated from the use two different risk factor values for the index chemical in the method. Cumulative chronic-toxic risks were also assessed, rendering below the threshold risk levels for all routes. This study showed that multi-route - multi-pathway exposure assessment and cumulative risk assessment should together be considered for better environmental and public health management.

PubMed ID: 33475343 2-s2.0-85100240278 As a result of its unique location, Turkey receives air masses from Europe, Russia, Middle East, and Africa, making it an important place in terms of long-range atmospheric transport (LRT) of contaminants. Atmospheric levels of 22 organochlorine pesticides (OCPs), 45 polychlorinated biphenyls (PCBs), and 14 polybrominated diphenyl ethers (PBDEs) were measured in two metropolitan cities, Istanbul and Izmir, on a weekly basis from May 2014 to May 2015. Dichlorodiphenyltrichloroethane (DDT) and its derivatives were dominant OCP species, followed by isomers of hexachlorocyclohexane (HCH) at both sites. The annual mean concentration of ?DDX (sum of o,p?-DDT, p,p?-DDT, o,p?-DDD, p,p?-DDD, o,p?-DDE, and p,p?-DDE) was 82 pg/m3 for Istanbul and 89 pg/m3 for Izmir, while these levels were about 46 pg/m3 for ?HCHs (sum of ?-, ?-, ?-, and ?-HCH) at both of the sites. At both stations, tri- and tetra-PCBs and tetra- and penta-PBDEs were dominant congeners. The temperature dependence indicates that both LRT and local contaminated areas contribute to the elevated levels. A Lagrangian particle dispersion model (FLEXPART) showed a few potential source regions in northern Africa and Middle East, southern-southwestern and eastern Europe including Russia, as well as from local domestic metropolitan areas. © 2021 American Chemical Society. 112Y315 Consejo Nacional para Investigaciones Científicas y Tecnológicas, CONICIT We acknowledge funding from Turkish Scientific and Technological Research Council (TUBITAK) for the financial support under the grant scheme of The Scientific and Technological Research Projects Funding Program (Grant No. 112Y315).

Due to diversity of contaminants indoors and complexity in the physical structure of particulate matter, partition process of chemicals affects indoor concentration distribution. Synthetic Musk Compounds (SMCs) are ubiquitously found in household and personal care products, thus, in the environment. Exposure to SMCs is important for human health, therefore, their partitioning in indoor environmental media is a key issue. In this study, gas – particle, house dust, and window film partitioning of SMCs were investigated in an indoor micro-environment. In a sealed and unoccupied room, a polycyclic and nitro musk mixture was left for volatilization for an hour. Then, samples were collected using XAD-2 sandwiched between two PUF plugs, glass-fiber filter, and wipes for gas, PM10, window-film, house dust phases, respectively, for 145 h. Collected samples were analyzed using a GC–MS. Results demonstrated that SMC concentrations decreased over time, non-linearly. Six of the SMCs partitioned to PM10 with at least 10% at beginning of the experiment, whereas the number of compounds dropped to two at the end, showing that SMCs may partition well between the two phases but they tend to be in the gas phase. They were also detected in the film and dust phases but a decrease pattern similar to gas-particle was not observed. Spearman correlations indicate that the dust and film-associated concentrations were governed by similar processes but PM-associated concentrations were not. SMCs may be found in all phases, mainly in house dust in terms of mass among the studied media and unaccounted surface reservoirs. Therefore, their partitioning between indoor media has key implications for human exposure.

The COVID-19 pandemic, which has reached 4 million global cases as of March 10, 2020, has become a worldwide problem. Turkey is one of the most affected (9th in the world) country with 139 771 cases. An intermittent curfew policy that differ for three age groups, and an intercity travel ban varying within the country have been implemented. The effects of changes in social life and industrial activity in terms of environmental pollution are not yet known. The short-term effects on PM2.5, PM10, SO2, NO2, NO, NOx, O3 and CO concentrations measured at 51 air quality measurement stations (AQMS) in 11 cities in March – April period of 2020 were statistically compared with that of the previous year. While PM2.5 (9/14 AQMS) and PM10 (29/35 AQMS) concentrations were not significantly affected, NO (12/24 AQMS), NO2 (20/29 AQMS), NOX (17/25 AQMS) concentrations were decreased, SO2 concentrations at half of the AQMSs (11/25) did not show a significant change. There were stations at which higher pollutant concentrations were measured in the study period in 2020 compared to that of 2019. Excess risks associated with PM2.5 and PM10 were estimated to be variable, albeit with a small difference. In conclusion, the heterogeneous actions taken in response to the COVID-19 pandemic resulted in mixed effects on ambient air quality. © 2021 The Author(s)

Sofuoglu, Sait C/0000-0001-6990-0275; Ozturk, Fatma/0000-0001-5179-8444, WOS: 000432475300003, PubMed: 29573689, Cancer has become the primary reason of deaths in Dilovasi probably due to its location with unique topography under the influence of heavy industrialization and traffic. In this study, possible sources and carcinogenic health risks of PAHs and PCBs were investigated in Dilovasi region by Positive Matrix Factorization ( PMF) and the USEPA approach, respectively. PAHs and PCBs were measured monthly for a whole year at 23 sampling sites using PUF disk passive samplers. Average ambient air concentrations were found as 285 +/- 431 ng/m(3) and 4152 +/- 6072 pg/m(3), for Sigma(15)PAH and Sigma 41PCB, respectively. PAH concentrations increased with decreasing temperature especially at urban sites, indicating the impact of residential heating in addition to industrial activities and traffic. On the other hand, PCB concentrations mostly increased with temperature probably due to enhanced volatilization from their sources. Possible sources of PAHs were found as emissions of diesel and gasoline vehicles, biomass and coal combustion, iron and steel industry, and unburned petroleum/petroleum products, whereas iron-steel production, coal and biomass burning, technical PCB mixtures, and industrial emissions were identified for PCBs. The mean carcinogenic risk associated with inhalation exposure to PAHs and PCBs were estimated to be >10(-6) and >10(-5), respectively, at all sampling points, while the 95th percentile was >10(-5) at 15 of 23 and >10(-4) at 8 of 23 sampling locations, respectively. Probabilistic assessment showed, especially for PCBs, that a majority of Dilovasi population face significant health risks. The higher risks due to PCBs further indicated that PCBs and possibly other pollutants originating from the same sources such as PBDEs and PCNs may be an important issue for the region. (c) 2018 Elsevier B.V. All rights reserved.

Olive Mill Wastewater (OMW) contains high concentrations of contaminants, including organic, nitrogen, and phenolic compounds that are extremely harmful to the environment and human health. The key purpose of this study was to remove total organic carbon (TOC), total nitrogen (TN), and phenolic compounds (TP) from OMW using floating wetland planted with Vetiveria zizanioides (L.) Nash (vetiver) and Cyperus alternifolius L. (umbrella palm) species. A total of eighteen floating wetlands were constructed. Twelve tanks were planted with vetiver and umbrella palm while another six tanks were maintained as unplanted controls. Experiments were conducted with wastewater volume of 56 L for 67 days using 5% (OMW-5) and 15% (OMW-15) treatments of OMW in a greenhouse. The highest TOC, TN, and TP removal efficiencies were found to be 95.3 ± 0.01, 82.7 ± 2.55, and 98.8 ± 0.07% in umbrella palm planted OMW-5, while the removal efficiencies were 84.9 ± 0.38, 92.7 ± 0.37, and 38.9 ± 1.97% in vetiver planted OMW-5. Similarly, the TOC, TN, and TP removal efficiencies in OMW-15 were 89.3 ± 0.28, 40.86 ± 1.73, and 96.8 ± 0.18% with umbrella palm and 89.1 ± 0.70, 23.7 ± 1.27, and 92.1 ± 0.41% with vetiver. The plants accumulated trace elements, especially in the roots, with the order of Fe > Mn > Cu > Zn > B > Pb > Cr > Ni > Co > Cd for umbrella palm. The umbrella palm shoot phenol content was found to be 2358 ± 201 and 1421 ± 198 mg/kg in OMW-5 and OMW-15, respectively. Overall, this study revealed that floating wetlands planted with vetiver and umbrella palm species have the potential to be used as a green treatment method to treat diluted high strength OMW.

WOS: 000395353600090, PubMed ID: 27939936, Atmospheric and concurrent soil samples were collected during winter and summer of 2014 at 41 sites in Kutahya, Turkey to investigate spatial and seasonal variations, sources, air-soil exchange, and associated carcinogenic risks of polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs). The highest atmospheric and soil concentrations were observed near power plants and residential areas, and the wintertime concentrations were generally higher than ones measured in summer. Spatial distribution of measured ambient concentrations and results of the factor analysis showed that the major contributing PAH sources in Kutahya region were the coal combustion for power generation and residential heating (48.9%), and diesel and gasoline exhaust emissions (473%) while the major PCB sources were the coal (thermal power plants and residential heating) and wood combustion (residential heating) (45.4%), and evaporative emissions from previously used technical PCB mixtures (34.7%). Results of fugacity fraction calculations indicated that the soil and atmosphere were not in equilibrium for most of the PAHs (88.0% in winter, 87.4% in summer) and PCBs (76.8% in winter, 83.8% in summer). For PAHs, deposition to the soil was the dominant mechanism in winter while in summer volatilization was equally important. For PCBs, volatilization dominated in summer while deposition was higher in winter. Cancer risks associated with inhalation and accidental soil ingestion of soil were also estimated. Generally, the estimated carcinogenic risks were below the acceptable risk level of 10-6. The percentage of the population exceeding the acceptable risk level ranged from 10-6, Scientific and Technological Research Council of Turkey [TUB/112Y305]; Anadolu University research fund for scientific projects [1306F272]; Gizem Tuna Tuygun and Hasan Altiok (Dokuz Eylul University), This study was supported by The Scientific and Technological Research Council of Turkey (project no: TUB/112Y305) and by Anadolu University research fund for scientific projects (project no: 1306F272). We would like to thank Gizem Tuna Tuygun and Hasan Altiok (Dokuz Eylul University) for their support during the study.

Polycyclic aromatic hydrocarbons (PAHs) and some of their nitrated derivatives, NPAHs, are seemingly ubiquitous in the atmospheric environment. Atmospheric lifetimes may nevertheless vary within a wide range, and be as short as a few hours. The sources and sinks of NPAH in the atmosphere are not well understood. With a Lagrangian field experiment and modeling, we studied the conversion of the semivolatile PAHs fluoranthene and pyrene into the 2-nitro derivatives 2-nitrofluoranthene and 2-nitropyrene in a cloud-free marine atmosphere on the time scale of hours to 1 day between a coastal and an island site. Chemistry and transport during several episodes was simulated by a Lagrangian box model i.e., a box model coupled to a Lagrangian particle dispersion model, FLEXPART-WRF. It is found that the chemical kinetic data do capture photochemical degradation of the 4-ring PAHs under ambient conditions on the time scale of hours to 1 day, while the production of the corresponding NPAH, which sustained 2-nitrofluoranthene/fluoranthene and 2-nitropyrene/pyrene yields of (3.7 ± 0.2) and (1.5 ± 0.1)%, respectively, is by far underestimated. Predicted levels of NPAH come close to observed ones, when kinetic data describing the reactivity of the OH-adduct were explored by means of theoretically based estimates. Predictions are also underestimated by 1-2 orders of magnitude, when NPAH/PAH yields reported from laboratory experiments conducted under high NOx conditions are adopted for the simulations. It is concluded that NPAH sources effective under low NOx conditions, are largely underestimated., Grant Agency of the Czech Republic (P503 16-115375); Izmir Institute of Technology Research Fund (2013IYTE-14); Max Planck Society; European Union (262254); Ministry of Education, Youth & Sports - Czech Republic (LM2015051/CZ.02.1.01/0.0/0.0/16_013/0001761)

Symposium on Legacy and Emerging Flame Retardants - Occurrence, Human Exposure and Toxicokinetics (DIOXIN) -- 2018 -- Krakow, POLAND WOS:000472694200025 PubMed ID: 31129402 Brominated flame retardants (BFRs) are found in multi-media indoors, therefore, may pose serious risks to human health. This study investigated the occurrence of BFRs in particulate matter (PM1 and PM10 and gas phase by active and passive sampling, and settled dust to estimate potential exposure in a computer technical service. Polybrominated diphenyl ethers (PBDEs) and their alternatives (novel BFRs, NBFRs) were studied. PM and gas phase were collected on glass fiber filters and polyurethane foam plugs, respectively, and analyzed with a GC/MS after extraction, clean-up, and concentration. Inhalation exposure of the staff was estimated based on the measured concentrations using Monte Carlo simulation. BDE-209 was the dominating PBDE congener in all media while bis(2-ethylhexyl)-3,4,5,6-tetrabromophthalate and 1,2-bis(2,4,6-tribromophenoxy)ethane were those of NBFRs. Submicron particulate matter (PM1) BFR levels constituted about one half of the PM10-associated concentrations, while average PM10 mass concentration (69.9 mu g m(-3)) was nine times that of PM1 (7.73 mu g m(-3)). Calculated log(10) dust-gas and PM-gas partitioning coefficients ranged from -5.03 to -2.10, -2.21 to -0.55, and -2.26 to -1.04 for settled dust, PM10, and PM1, respectively. The indoor/outdoor concentration ratios were >1 for all compounds indicating the strength of indoor sources in the service. The estimated potential inhalation exposures, for future chronic-toxic and carcinogenic risk assessments, indicated that the levels of gas-phase and PM1-associated exposures were similar at approximately one half of PM10-associated levels. Results of this study indicate that the occurrence of BFRs in all studied media should be taken into consideration for occupational health mitigation efforts. (C) 2019 Elsevier Ltd. All rights reserved.

A number of green treatment technologies have been used for textile wastewater treatment, among which phytoremediation is a low cost, effective, and promising alternative — to conventional treatment techniques. The aim of this study was to investigate performance of Lemna minor (L. minor) for phytoremediation of Methylene Blue (MB). A Box–Behnken experimental design (BBD) was applied to study individual and combined effect of operating parameters on MB dye removal efficiency: MB dye concentration ( x 1 : 5 – 25 mgL−1), amount of L. minor ( x 2 : 1 – 5 g), and pH of the solution ( x 3 : 4.5 – 9.0). Response surface analysis and response model were utilized to reveal the relationship between operating parameters and MB removal efficiency. Fourier Transform Infrared Spectroscopy (FTIR) and Scanning Electron Microscopy (SEM) analyses of L. minor samples were used to infer on the removal mechanism. The predicted optimum values were x 1 = 15 mgL−1, x 2 = 4 . 9 g, and x 3 = 6 . 8 , for the highest removal efficiency (98%) within 24 h. FTIR and SEM analyses indicated that the dye removal mechanism was mainly biosorption. Desorption experiments revealed that L. minor released only a small fraction of the sorbed dye. Consequently, in addition to being environmental friendly and cost effective, results of this study show that L. minor can be effectively used for MB dye removal from wastewaters while adding to the pertinent but limited literature by presenting its applicability in wider operating parameter ranges, maximization of removal efficiency through experimental design, and evidence that biosorption is a plausible mechanism.

Ergene Basin is located in Thrace, Turkey, where industries are densely populated. This study aimed to determine exposure of people living in Ergene Basin (Corlu and Cerkezkoy) to fine and coarse PM, and its potentially toxic element (PTE) content by considering variation in respiratory airway deposition rates with daily activities and PM particle size by employing deposition models of International Commission on Radiological Protection and Multiple Path Particle Dosimetry. Fine and coarse PM samples were collected daily for a year at points in Corlu and Cerkezkoy representing urban and industrial settings, respectively. A questionnaire survey was conducted in the study area to obtain time-activity budgets, and associated variation was included in the health risk assessment by considering time-activity-dependent inhalation rates. The studied PTEs were Al, As, Ba, Cd, Cr, Co, Mn, Ni, Pb, and Se. The mean fine and coarse PM concentrations were measured as 23 and 14 mu g/m(3) in Corlu, and 22 and 12 mu g/m(3) in Cerkezkoy, respectively. The only PTE that exceeded acceptable risk in terms of total carcinogenic risk was Cr. Non-carcinogenic risks of all the PTEs including Cr were below the threshold. The use of deposition fractions in the health risk assessment (HRA) calculations was found to prevent overestimation of health risks by at least 91% and 87% for fine and coarse PM, respectively, compared to the regular HRA. Minor differences in risk between Corlu and Cerkezkoy suggest that urban pollution sources could be at least as influential on human health as industrial sources. (C) 2020 Elsevier B.V. All rights reserved.

This study reports levels of indoor environmental quality variables before and after installation of heat recovery ventilation in a primary school located in an urban area in Izmir, Turkey. A CO2-based modeling was performed to determine the required flow rates that would comply with an international ventilation standard, followed by computational fluid dynamics modeling for best airflow distribution in a classroom. Temperature, CO2, PM2.5, and total volatile organic compounds were found at undesired levels, among which relative humidity, CO2, and PM2.5 were improved after the intervention. Reductions in the mean and maximum concentrations were 29% and 68% for CO2 and 29% and 46% for PM2.5. This intervention study was a part of the city-wide main project that aimed to increase awareness of the students and their families, teachers, and staff regarding importance of indoor environmental quality in both at school and home due to its possible effects on children's health and academic performance, one of the major challenges of today's societies all around the globe., Mechanical Engineering Chamber of Izmir; HVAC industry; Ministry of Education-Izmir Directorate

Sofuoglu, Sait C/0000-0001-6990-0275; Bingol, Ferhat/0000-0002-8071-3814, WOS: 000437395400047, PubMed: 29736652, Development of new wind energy projects require complex planning process involving many social, technical, economic, environmental, political concerns, and different agents such as investors, utilities, governmental agencies, or social groups. The aim of this study is to develop a tool combining Geographic Information System (GIS) and Multi-Criteria Decision-Making (MCDM) methodologies, and its application for Turkey as a case study. A variety of constraints and criteria were identified based on a literature review and regulations gathered from variety of agencies, use of which resulted in determination of infeasible sites. Then, pairwise comparisons were carried out using analytic hierarchy process as the MCDM method to estimate relative importance of the criteria, and to visualize a suitability map with three classes. As the final stage, decision making was carried out based on environmental impact where 45.5% of the Turkish territory was found as infeasible area. Sixty percent of the remaining area are covered by the moderate suitability class, followed by the highly suitable area (20.3%) and low suitable area (19.8%). The output of this study can be used by energy planners to estimate the extent that wind energy can be developed based on public perception, administrative, and environmental aspects.

Atmospheric levels of 43 PCBs, 22 OCPs, and 14 PBDEs were determined in 16 cities at urban and rural sites by passive sampling to generate the first large-scale nationwide dataset of POP residues in Turkey's atmosphere. Sampling campaign was performed from May 2014 to April 2015 with three-month sampling periods at locations on east-west and north-south transects through the country to investigate seasonal and spatial variations, including long range atmospheric transport (LRAT). Factor analysis was conducted to infer on the potential sources. Overall average Σ43PCBs concentration was 108 ± 132 pg/m3. PCB-118 (26.3 ± 44.6 pg/m3) was the top congener, and penta-CBs had the highest contribution with 54.3%. ΣDDTs had the highest annual mean concentration with 134 ± 296 pg/m3 among the OCP groups among which the highest concentration compound was p'p-DDE (97.6 ± 236 pg/m3). Overall average concentration of Σ14PBDEs was 191 ± 329 pg/m3 with the highest contribution from BDE-190 (42%). Comparison of OCPs and PCBs concentrations detected at temperatures which were above and below annual average temperature indicated higher concentrations in the warmer periods, hence significance of secondary emissions for several OCPs and Σ43PCBs, as well as inference as LRAT from secondary emissions. The first nationwide POPs database constructed in this study, point to current use, local secondary emissions, and LRAT for different individual compounds, and indicate the need for regular monitoring. The first country-wide passive sampling of selected POPs showed no unequivocal trends reflecting transitional location of Turkey., TUBITAK (112Y314)

The occurrence and atmospheric behavior of tri- to deca-polybrominated diphenyl ethers (PBDEs) were investigated during a 2-week campaign concurrently conducted in July 2012 at four background sites around the Aegean Sea. The study focused on the gas/particle (G/P) partitioning at three sites (Ag. Paraskevi/central Greece/suburban, Finokalia/southern Greece/remote coastal, and Urla/Turkey/rural coastal) and on the size distribution at two sites (Neochorouda/northern Greece/rural inland and Finokalia/southern Greece/remote coastal). The lowest mean total (G + P) concentrations of ∑7PBDE (BDE-28, BDE-47, BDE-66, BDE-99, BDE-100, BDE-153, BDE-154) and BDE-209 (0.81 and 0.95 pg m−3, respectively) were found at the remote site Finokalia. Partitioning coefficients, KP, were calculated, and their linear relationships with ambient temperature and the physicochemical properties of the analyzed PBDE congeners, i.e., the subcooled liquid pressure (PL°) and the octanol-air partition coefficient (KOA), were investigated. The equilibrium adsorption (PL°-based) and absorption (KOA-based) models, as well as a steady-state absorption model including an equilibrium and a non-equilibrium term, both being functions of log KOA, were used to predict the fraction Φ of PBDEs associated with the particle phase. The steady-state model proved to be superior to predict G/P partitioning of BDE-209. The distribution of particle-bound PBDEs across size fractions < 0.95, 0.95–1.5, 1.5–3.0, 3.0–7.2, and > 7.2 μm indicated a positive correlation between the mass median aerodynamic diameter and log PL° for the less brominated congeners, whereas a negative correlation was observed for the high brominated congeners. The potential source regions of PBDEs were acknowledged as a combination of long-range transport with short-distance sources., Granting Agency of the Czech Republic (312334); Czech Ministry of Education, Youth, and Sports (LO1214--LM2015051); Izmir Institute of Technology Scientific Research Foundation (2013IYTE14); European Union FP7 (262254 ACTRIS)

Semi-volatile organic compounds were monitored over a whole year, by collection of gas and particle phases every sixth day at a suburban site in Izmir, Turkey. Annual mean concentrations of 32 polychlorinated biphenyls (∑32PCBs) and 14 polycyclic aromatic hydrocarbons (∑14PAHs) were 348 pg/m3 and 36 ng/m3, respectively, while it was 273 pg/m3 for endosulfan, the dominant compound among 23 organochlorine pesticides (OCPs). Monte Carlo simulation was applied to the USEPA exposure-risk models for the estimation of the population exposure and carcinogenic risk probability distributions for heating and non-heating periods. The estimated population risks associated with dermal contact and inhalation routes to ∑32PCBs, ∑14PAHs, and some of the targeted OCPs (α-hexachlorocyclohexane (α-HCH), β-hexachlorocyclohexane (β-HCH), heptachlor, heptachlor epoxide, α-chlordane (α-CHL), γ-chlordane (γ-CHL), and p,p′-dichlorodiphenyltrichloroethane (p,p′-DDT)) were in the ranges of 1.86 × 10−16–7.29 × 10−9 and 1.38 × 10−10–4.07 × 10−6, respectively. The inhalation 95th percentile risks for ∑32PCBs, ∑14PAHs, and OCPs were about 6, 3, and 4–7 orders of magnitude higher than those of dermal route, respectively. The 95th percentile inhalation risk for ∑32PCBs and OCPs in the non-heating period were 1.8- and 1.2–4.6 folds higher than in the heating period, respectively. In contrast, the 95th percentile risk levels for ∑14PAHs in the heating period were 4.3 times greater than that of non-heating period for inhalation, respectively. While risk levels associated with exposure to PCBs and OCPs did not exceed the acceptable level of 1 × 10−6, it was exceeded for 47 % of the population associated with inhalation of PAHs with a maximum value of about 4 × 10−6., Scientific and Technical Research Council of Turkey (ICTAG-C033); Izmir Institute of Technology (IYTE-BAP-20)

Indoor air quality in mosques during prayers may be of concern for sensitive/susceptible sub-groups of the population. However, no indoor air pollutant levels of potentially toxic agents in mosques have been reported in the literature. This study measured PM concentrations in a mosque on Friday when the mid-day prayer always receives high attendance. Particle number and CO2 concentrations were measured on nine sampling days in three different campaigns before, during, and after prayer under three different cleaning schedules: vacuuming a week before, a day before, and on the morning of the prayer. In addition, daily PM2.5 concentrations were measured. Number concentrations in 0.5-1.0, 1.0-5.0, and > 5.0 mu m diameter size ranges were monitored. In all campaigns the maximum number concentrations were observed on the most crowded days. The lowest number concentrations occurred when vacuuming was performed a day before the prayer day in two of the three size ranges considered. PM2.5 concentrations (four-hour samples that integrated before, during, and after the prayer) were comparable to the other indoor environments reported in the literature. CO2 concentrations suggested that ventilation was not sufficient in the mosque during the prayers. The results showed that better ventilation, a preventive cleaning strategy, and a more detailed study are needed. (C) 2012 Elsevier Ltd. All rights reserved.

UNLABELLED Indoor air gas and particulate-phase samples (PM(2.5) ) were collected from a primary school classroom and a women's sport center because children are one of the sensitive population subgroups and women are frequent users of personal care products in addition to the high level of activity in this specific microenvironment. PM(2.5) was collected with a Harvard impactor, and polyurethane foam was used for the gas phase. Samples were ultrasonically extracted, concentrated, and analyzed with a GC-MS. The mean gas-phase concentrations in the classroom ranged from 0.12 ± 0.2 ng/m(3) for MK to 267 ± 56 ng/m(3) for HHCB, while it was from 0.08 ± 0.10 ng/m(3) for AHMI to 144 ± 61 ng/m(3) for HHCB in the sports center. Particulate-phase average concentrations in the sports center ranged from 0.22 ± 0.11 ng/m(3) for ATII to 1.34 ± 071 ng/m(3) for AHTN, while it ranged from 0.05 ± 0.02 ng/m(3) (musk xylene) to 2.50 ± 0.94 ng/m(3) (HHCB) in the classroom. Exposure-risk assessment showed that inhalation route is most probably far less significant than the dermal route; however, it should be noted that the exposure duration covered in this study was not the larger fraction of the day. PRACTICAL IMPLICATIONS Synthetic musk compounds (SMCs) are found everywhere because their use in household and personal care products (laundry detergents, carpet cleaners, cleaning agents, fabric softener soaps, shampoos, cosmetics, etc.) has been increasing. These compounds are semi-volatiles that may result in direct and indirect exposures through inhalation route. Although SMCs were found to be dominant in the gas phase, exposure via inhalable particles may be important as we found several compounds in the particulate phase (PM(2.5)).

Artificial neural networks (ANN) were constructed to predict prevalence of building-related symptoms (BRS) of office building occupants. Six indoor air pollutants and four indoor comfort variables were used as input variables to the networks. A symptom metric was used as the measure of BRS prevalence, and employed as the output variable. Pollutant concentration, comfort variable, and occupant symptom data were obtained from the Building Assessment and Survey Evaluation study conducted by the US Environmental Protection Agency, in which all were measured concurrently. Feed-forward networks that employ back-propagation algorithm with momentum term and variable learning rate were used in ANN modeling. Root mean square error and R 2 value of the simple linear regression between observed and predicted output were used as performance measures. Among the constructed networks, the best prediction performance was observed in a one-hidden-layered network with an R 2 value of 0.56 for the test set. All constructed networks except one showed a better performance than the multiple linear regression analysis.

Indoor air quality has a great impact on human health. Cooking, in particular frying, is one of the most important sources of indoor air pollution. Indoor air CO, CO2, particulate matter (PM), and volatile organic compound (VOC) concentrations, including aldehydes, were measured in the kitchen of a small establishment where a special deep-frying margarine was used. The objective was to assess occupational exposure concentrations for cooks of such restaurants. While individual VOC and PM2.5 concentrations were measured before, during, and after frying events using active sampling, TVOC, PM10, CO, CO2, temperature, and relative humidity were continuously monitored through the whole period. VOC and aldehyde concentrations did not increase to considerable levels with deep-frying compared to the background and public indoor environment levels, whereas PM10 increased significantly (1.85 to 6.6 folds). The average PM2.5 concentration of the whole period ranged between 76 and 249 μg/m3. Hence, considerable PM exposures could occur during deep-frying with the special margarine, which might be sufficiently high to cause health effects on cooks considering their chronic occupational exposures., Dokuz Eylul University (BAP-2011.KB.SAG.017)

Near-ground air (26 substances) and surface seawater (55 substances) concentrations of persistent toxic substances (PTS) were determined in July 2012 in a coordinated and coherent way around the Aegean Sea based on passive air (10 sites in 5 areas) and water (4 sites in 2 areas) sampling. The direction of air–sea exchange was determined for 18 PTS. Identical samplers were deployed at all sites and were analysed at one laboratory. hexachlorobenzene (HCB), hexachlorocyclohexanes (HCHs) as well as dichlorodiphenyltrichloroethane (DDT) and its degradation products are evenly distributed in the air of the whole region. Air concentrations of p,p′-dichlorodiphenyldichloroethylene (p,p′-DDE) and o,p′-DDT and seawater concentrations of p,p′-DDE and p,p′-DDD were elevated in Thermaikos Gulf, northwestern Aegean Sea. The polychlorinated biphenyl (PCB) congener pattern in air is identical throughout the region, while polybrominated diphenylether (PBDE)patterns are obviously dissimilar between Greece and Turkey. Various pollutants, polycyclic aromatic hydrocarbons (PAHs), PCBs, DDE, and penta- and hexachlorobenzene are found close to phase equilibrium or net-volatilisational (upward flux), similarly at a remote site (on Crete) and in the more polluted Thermaikos Gulf. The results suggest that effective passive air sampling volumes may not be representative across sites when PAHs significantly partitioning to the particulate phase are included., Granting Agency of the Czech Republic (312334); Czech Ministry of Education (LO1214--LM2011028); European Social Fund (CZ.1.07/2.3.00/30.0037); European Commission FP7 (262254 ACTRIS)

Ambient concentrations of volatile organic compounds (VOCs), nitrogen dioxide (NO2), sulphur dioxide (SO2) and ground-level ozone (O3) were measured at 55 locations around a densely populated industrial zone, hosting a petrochemical complex (Petkim), a petroleum refinery (Tupras), ship-dismantling facilities, several iron and steel plants, and a gas-fired power plant. Five passive sampling campaigns were performed covering summer and winter seasons of 2005 and 2007. Elevated concentrations of VOCs, NO2 and SO2 around the refinery, petrochemical complex and roads indicated that industrial activities and vehicular emissions are the main sources of these pollutants in the region. Ozone concentrations were low at the industrial zone and settlement areas, but high in rural stations downwind from these sources due to NO distillation. The United States Environmental Protection Agency's positive matrix factorization receptor model (EPA PMF) was employed to apportion ambient concentrations of VOCs into six factors, which were associated with emissions sources. Traffic was found to be highest contributor to measured ∑VOCs concentrations, followed by the Petkim and Tupras.Median cancer risk due to benzene inhalation calculated using a Monte Carlo simulation was approximately 4 per-one-million population, which exceeded the U.S. EPA benchmark of 1 per one million. Petkim, Tupras and traffic emissions were the major sources of cancer risk due to benzene inhalation in the Aliaga airshed. Relative contributions of these two source groups changes significantly from one location to another, demonstrating the limitation of determining source contributions and calculating health risk using data from one or two permanent stations in an industrial area., TUBITAK (104Y276)

Indoor air pollution in university research laboratories may be important to building occupants, especially for those who work in the laboratories. In this study, indoor air quality (IAQ) and indoor environmental comfort were investigated in research laboratories of two departments at a university. PM2.5, PM10, TVOC (total volatile organic compounds), and CO concentrations, and three comfort variables which are temperature, relative humidity, and CO2 were measured. PM2.5 concentration was determined gravimetrically by collecting particles on glass fiber filters, whereas the remaining pollutants and comfort variables were measured using a monitoring device. IAQ measurements showed that levels of all pollutants were under the limits in both of the departments except for TVOC in one laboratory which had a mean concentration of 182 ppb. The comfort variables were in the comfort ranges for laboratories in both of the departments except for temperature in one laboratory with a mean value of 30 degrees C. In conclusion, measures are needed for extensive uses of organic solvents because ventilation may not be sufficient to keep VOC concentrations within the limits, and to provide thermal comfort.

Concentrations of volatile organic compounds (VOCs) were measured in the drinking water in Province of İzmir, Turkey, and associated health risks due to ingestion of these compounds were investigated using population weighted random samples. A total of 100 houses were visited in different districts of İzmir and drinking water samples were collected from consumers' drinking water source. Questionnaires were administered to one participant in each house to determine demographics and drinking water consumption rates. Oral exposure and risks were estimated for each participant and İzmir population by deterministic and probabilistic approaches, respectively. The four trihalomethane (THM) species (i.e., chloroform, bromodichloromethane, dibromochloromethane, and bromoform), benzene, toluene, p-xylene, and naphthalene were the most frequently detected VOCs with concentrations ranging from below detection limit to 35 μg/l. The risk estimates were found to be less than the values reported in the literature with few exceptions. Noncarcinogenic risks attributable to ingestion of VOCs for İzmir population were negligible, whereas the mean carcinogenic risk estimates for bromodichloromethane and dibromochloromethane were above the de minimis level of one in a million (10-6). For all VOCs, the concentrations measured in metropolitan area were greater than those in other districts. All THM species were detected in higher concentrations in tap water, whereas nontap water contained more benzene, toluene, p-xylene, and naphthalene. Therefore, the concentrations of the latter four compounds and associated risks increased with increasing income and education level since bottled water was used in larger proportions within these subgroups. The results of this study showed that oral exposure to drinking water contaminants and associated risks may be higher than the acceptable levels even if the concentrations fall below the standards., TÜBİTAK

When exposures to metals and volatile organic chemicals in drinking water were compared for the population of Arizona and that of border communities, average daily exposures and associated risks were found to be smaller in the border communities than in the state population.

It was recently shown that substantial amounts of halogenated volatile organic compounds (VOCs) are formed in chlorine-bleach-containing household products as a result of reactions of sodium hypochlorite with organic product components. Use of these household products results in elevated indoor air halogenated VOC concentrations. Halogenated VOCs in several chlorine-bleach-containing household products (plain, n=9; fragranced, n=4; and surfactant-added, n=29) from Europe and North America were measured in the present study. Chloroform and carbon tetrachloride were the dominating compounds having average concentrations of 9.5±29.0 (average±SD) and 23.2±44.3 (average±SD) mgL-1, respectively. Halogenated VOC concentrations were the lowest in plain bleach, slightly higher in fragranced products and the highest in the surfactant-added products. Investigation of the relationship between the halogenated VOCs and several product ingredients indicated that chlorinated VOC formation is closely related to product composition. Indoor air concentrations from the household use of bleach products (i.e., bathroom, kitchen, and hallway cleaning) were estimated for the two dominating VOCs (chloroform and carbon tetrachloride). Estimated indoor concentrations ranged between 0.5 and 1030 (34±123, average±SD) μgm-3 and 0.3-1124 (82±194, average±SD) μgm-3 for chloroform and carbon tetrachloride, respectively, indicating substantial increases compared to background. Results indicated that indoor air concentrations from surfactant-added products were significantly higher (p

A novel sorbent, chitosan-immobilized pumice, has been prepared for the sorption of As(V) from waters prior to its determination by hydride generation atomic absorption spectrometry. The success of the immobilization has been checked with such characterization techniques as scanning electron microscopy, thermal gravimetric analysis, and elemental analysis. Points of zero charge of the sorbents were determined with potentiometric mass titration. Batch-type equilibration studies have shown that the novel sorbent can be employed at a wide pH range resulting in quantitative sorption (>90 %) at pH 3.0–7.0 and greater than 70 % sorption at pH >8.0. These results demonstrate the advantage of immobilizing chitosan onto pumice, because, under the same conditions, pumice displays

The aim of this study was to conduct a carcinogenic risk assessment for exposure to polycyclic aromatic hydrocarbons (PAHs) via routes of inhalation and dermal contact. Concentrations of 19 PAM species were determined during a heating period at a site in the city of Balikesir, Turkey. Two questionnaires were administered to a sample of inhabitants to determine time-activity budgets and demographic information. The assessment was conducted for each participant and Balikesir population by deterministic and probabilistic approaches, respectively. Monte Carlo simulation was implemented to determine the population exposure-risk probability distributions. The estimates were based on benzo[a]pyrene equivalent (BaPeq) total PAM concentrations calculated using toxic equivalency factors. The mean and median BaPeq concentrations of gaseous and particulate phases were 3.25 and 134, and 38.5 and 34.0 ng/m(3), respectively. Carcinogenic risk for inhalation exposure route was estimated by using two different slope factor values (3.9 and 304.5 (mg/kg-day)(-1)), recommended by two different organizations, resulting in two (order(s) of magnitude apart) population risk ranges: 1.32 x 10(-7)-2.23 x 10(-4), and 1.61 x 10(-5)-7.95 x 10(-3), respectively. The population risks associated with dermal exposure were lower compared to those of inhalation, ranging from 6.58 x 10(-9) to 2.57 x 10(-6). The proportion of the population with risks higher than the general acceptable level (1.0 x 10(-6)) was estimated as > 99 percent, for inhalation, and as 28 percent for dermal exposure route. (C) 2014 Elsevier Inc. All rights reserved. Scientific and Technological Research Council of Turkey (TUBITAK)Turkiye Bilimsel ve Teknolojik Arastirma Kurumu (TUBITAK) [108Y166] This study was supported by a grant (108Y166) from the Scientific and Technological Research Council of Turkey (TUBITAK). The authors thank Emin Taylan of Middle East Technical University, Ankara, Turkey, for the analysis of the samples.

In this study, which was a part of the Atmospheric Exchange Over Lakes and Oceans Study (AEOLOS) investigation, the dry deposition fluxes and atmospheric size distributions (ASDs) of mass and crustal metals (aluminum and magnesium) were measured over the southern basin of Lake Michigan (in Chicago, over Lake Michigan, and in South Haven, Michigan). Airborne crustal metals arise primarily from fugitive dust emissions and are associated with the coarse fraction of atmospheric aerosol. Consequently, they can serve as fingerprints for the atmospheric behavior of fugitive dust. The flux of these metals were substantially higher in Chicago than in either South Haven or over Lake Michigan. The measured average mass, aluminum, and magnesium fluxes were 138, 2.23, and 5.32 mg/m2-day in Chicago, 47.8, 0.24, and 0.28 mg/m2-day over Lake Michigan, and 37.4, 0.17, and 0.12 mg/m2-day in South Haven, respectively. The ASDs of crustal metals measured in Chicago had higher concentrations of coarse particles than ASDs measured over Lake Michigan and in South Haven. The calculated flux of metals using a multistep model and dry deposition velocities obtained from the Sehmel-Hodgson model were in general agreement with measured fluxes of crustal metals. Particles >10 μm were found to be responsible for the majority of the flux.

Arsenic species were determined in rice and bulgur samples that were collected from 50 participants who also supplied exposure related information through a questionnaire survey. Speciation analysis was conducted using an HPLC–ICP-MS system. Ingestion exposure to arsenic and associated health risks were assessed by combining the concentration and questionnaire data both for individual participants and the subject population. Inorganic arsenic dominated both in rice and bulgur but concentrations were about an order of magnitude higher in rice (160 ± 38 ng/g) than in bulgur. Because participants also consumed more rice than bulgur, exposures were significantly higher for rice resulting in carcinogenic risks above acceptable level for 53% and 93% of the participants when the in-effect and the proposed potencies were used, respectively, compared to 0% and 5% for bulgur. An inorganic arsenic standard for rice would be useful to lower the risks while public awareness about the relation between excessive rice consumption and health risks is built, and bulgur consumption is promoted.

This study assessed concentrations and investigated potential source regions for PCBs, PBDEs, and organochlorine pesticides in Acadia National Park, Maine, USA. Back-trajectories and potential source contribution function (PSCF) values were used to map potential source areas for total-PCBs, BDE-47, and 10 organochlorine pesticides. The constructed PSCF maps showed that ANP receives high pollutant concentrations in air masses that travel along four main pathways: (1) from the SW along the eastern Atlantic seaboard, (2) from the WSW over St. Louis, and Columbus regions, (3) from the west over Chicago, and Toronto regions, and (4) from WNW to NNW over the Great Lakes, and Quebec regions. Transport of all studied pollutants were equally distributed between the first three pathways, with only minor contributions from the last pathway. This study concludes that the high-pollutant concentrations arriving at ANP do not exclusively originate from the major urban centers along the eastern Atlantic seaboard.

Olive tree leaf samples were collected to investigate their possible use for biomonitoring of lipophilic toxic substances. The samples were analyzed for 28 polychlorinated biphenyls (PCB) congeners. Twelve congeners were detected in the samples. PCB-60, 77, 81, 89, 105, 114, and 153 were the most frequently detected congeners ranging from 32 % for PCB-52 to 97 % for PCB-81. I (12)PCBs pound concentration varied from below detection limit to 248 ng/g wet weight in the sampling area, while the mean congener concentrations ranged from 0.06 ng/g (PCB-128 + 167) to 64.2 ng/g wet weight (PCB-60). Constructed concentration maps showed that olive tree leaves can be employed for the estimation of spatial distrubution of these congeners.

Introduction: In this study, olive tree leaves, collected from 50 sampling sites throughout the Province of Aydi{dotless}n, Turkey, were used to estimate level of pollution by measuring Al, As, B, Ba, Ca, Co, Cr, Cu, Fe, K, Li, Mg, Mn, Na, Ni, Pb, Sr, and Zn concentrations and calculating pollution factor (PF) values. Materials and methods: After sample preparation, collected leaves were microwave digested, and extracts were analyzed by an inductively coupled plasma-mass spectrometer. Results and discussion: The maximum PF values were ≥10 for a number of elements ranging from 11-13 (Al, As, Cr, Fe, Mn, Ni) to >100 for Cu, Li, and Na. Urban-rural and roadside-nonroadside concentration comparisons showed that some of the elements (As, Cu, and Pb) were at significantly higher levels on urban and/or roadside sampling sites. Summary and conclusion: Correlations and factor analysis showed that there may be common sources for some elements, which included several soil types and anthropogenic activities. Based on the results of the statistical source apportionment, possible sources were narrowed down with help of the constructed elemental concentration maps. In conclusion, utilization of olive tree leaves for biomonitoring and assessment of environmental pollution was shown to be possible in the Mediterranean region where they are indigenous and cultivated.

PubMed: 20833585 Concentrations of volatile organic compounds (VOCs), including formaldehyde, in classrooms, kindergartens, and outdoor playgrounds of three primary schools were measured in spring, winter, and fall terms in Izmir, Turkey. A health-risk assessment was conducted for odor detection, sensory irritation, chronic toxic effects, and cancer. Active sampling was applied for VOCs and formaldehyde on Tenax TA and DNPH tubes, respectively. VOCs were analyzed in a thermal desorption-GC-MS system. Formaldehyde analysis was performed using an HPLC instrument. Benzene, toluene, and formaldehyde were the most abundant compounds with 95th percentile indoor air concentrations of 29, 87, and 106?g/m3, respectively. Naphthalene and xylenes followed them with an order of magnitude lower concentrations. Two isomers of dichlorobenzene (1,3 and 1,4) were the other notable compounds. The concentrations were utilized to classify the indoor air pollutants with respect to potential health effects. In addition, carcinogenic and chronic toxic risks were estimated using Monte-Carlo simulation. Formaldehyde appears to be the most concerning pollutant with high chronic toxic and carcinogenic risk levels according to the health assessment followed by naphthalene, benzene, and toluene due to their chronic effects. Türkiye Bilimsel ve Teknolojik Araştirma Kurumu, TÜBITAK This study was supported by a research grant ( 105Y263 ) from the Scientific and Technical Research Council of Turkey (TUBITAK) . GC–MS and HPLC analyses were performed at Environmental Research Center, İzmir Institute of Technology. We thank Dr. M. Odabasi for his help during method development for TD–GC–MS analysis.

The aqueous phase adsorption of fuel oxygenates methyl tertiary butyl ether (MTBE) and ethyl tertiary butyl ether (ETBE) onto commercially available granular activated carbon (GAC; Norit GAC 1240) was investigated in a batch system at 27°C. The oxygenate concentrations were determined by headspace gas chromatography/mass spectrometry analyses. The experimental data were used with four two-parameter isotherm models (Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich) and two kinetic models (pseudo first-order and pseudo second-order) to determine equilibrium and kinetic parameters. Considering the correlation coefficient and root mean square error, Dubinin-Radushkevich isotherm showed better fit with the equilibrium data for MTBE. However, the performances of Langmuir and Dubinin-Radushkevich models were comparable for ETBE. The adsorption capacities were calculated as 5.50 and 6.92 mg/g for MTBE and ETBE, respectively, at an equilibrium solution concentration of 1 mg/L using Dubinin-Radushkevich isotherm. The differences between the model predictions and experimental data were similar for the pseudo first-order and pseudo second-order kinetic models. Gibbs free-energy changes of adsorption were found to be -22.59 and -28.55 kJ/mol for MTBE-GAC and ETBE-GAC systems, respectively, under the experimental conditions studied., TÜBİTAK

Seasonal variation in concentrations of two different disinfection by-product groups, trihalomethanes (THMs) and haloacetonitriles (HANs), was investigated in tap water samples collected from five sampling points (one groundwater and four surface water sources) in Izmir, Turkey. Estimates of previously published carcinogenic and non-carcinogenic risks through oral exposure to THMs were re-evaluated using a probabilistic approach that took the seasonal concentration variation into account. Chloroform, bromoform, dibromochloromethane and dichloroacetonitrile were the most frequently detected compounds. Among these, chloroform was detected with the highest concentrations ranging from 0.03 to 98.4 µg/L. In tap water, at the groundwater supplied sampling point, brominated species, bromoform and dibromoacetonitrile, were detected at the highest levels most probably due to bromide ion intrusion from seawater. The highest total THM and total HAN concentrations were detected in spring while the lowest in summer and fall. The annual average total THM concentration measured at one of the surface water supplied sampling points exceeded the USEPA's limit of 80 µg/L. While all non-carcinogenic risks due to exposure to THMs in Izmir drinking water were negligible, carcinogenic risk levels associated with bromodichloromethane and dibromochloromethane were higher than one in million.

A health risk assessment was conducted for exposure to trace metals via drinking water ingestion pathway for Province of Izmir, Turkey. Concentrations of 11 trace metals were measured in drinking waters collected from 100 population weighted random sampling units (houses). The samples were analyzed in atomic absorption spectrometry for arsenic, and inductively coupled plasma-optical emission spectrometry for Be, Cd, Co, Cr, Cu, Mn, Ni, Pb, V, and Zn. Questionnaires were administered to a participant from each sampling unit to determine drinking water consumption related information and demographics. Exposure and risks were estimated for each individual by direct calculation, and for Izmir population by Monte Carlo simulation. Six trace metals (As, Cr, Cu, Mn, Ni, and Zn) were detected in >50% of the samples. Concentrations of As and Ni exceeded the corresponding standards in 20% and 58% of the samples, respectively. As a result, arsenic noncarcinogenic risks were higher than the level of concern for 19% of the population, whereas carcinogenic risks were >10(-4) for 46%, and >10(-6) for 90% of the population.

Exposure and associated health risks for fluoride and trace metals in black tea were estimated. Fifty participants were randomly recruited to supply samples from the tea that they drink, and self-administer a questionnaire that inquired about personal characteristics and daily tea intake. Analyzed trace metals included aluminum, arsenic, barium, cadmium, cobalt, chromium, copper, manganese, nickel, strontium, and zinc. Fluoride and four metals (Al, Cr, Mn, Ni) were detected in all samples while barium was detected only in one sample. The remaining metals were detected in >60% of the samples. Fluoride and aluminum levels in instant tea bag samples were greater than in loose tea samples (p < 0.05) while the differences in elemental concentrations of loose and pot bag tea samples were not significant. Median and 90th percentile daily tea intake rates were estimated as 0.35 and 1.1 l/day, respectively. Neither fluoride nor aluminum levels in black tea were found to associate with considerable risks of fluorosis and Alzheimer's disease, respectively. However, carcinogenic risk levels for arsenic were high; R > 1.0 × 10-6 even at the median level. According to sensitivity analysis, daily tea intake was the most influencing variable to the risk except for arsenic for which the concentration distribution was of more importance.

An Artificial Neural Networks (ANNs) model is constructed to forecast SO 2 concentrations in Izmir air. The model uses meteorological variables (wind speed and temperature) and measured particulate matter concentrations as input variables. The correlation coefficient between observed and forecasted concentrations is 0.94 for the network that uses all three variables as input parameters. The root mean square error value of the model is 3.60 g/mt 3 . Considering the limited number of available input variables, model performances show that ANNs are a promising method of modeling to forecast ambient air SO 2 concentrations in Izmir.

An index for indoor environmental quality, the Indoor Environmental Index (IEI), was developed. This study aggregates the Indoor Air Pollution Index, an index found in the literature, and a new index: the Indoor Discomfort Index. The average of these two indices is the IEI, which is calculated using concentrations of eight pollutants and two comfort variables measured in 100 office buildings in the United States. The database used was developed for the U.S. Environmental Protection Agency Building Assessment Survey Evaluation study. A symptom index also is developed to denote persistent occupant symptoms. The IEI and the symptom index are used to investigate the relationship between indoor environmental quality and symptoms. Two simple linear regression models were formulated; these models explain 67 and 79% of the variation in the average symptom index, with the variation of the average IEI depending on the method of averaging used in the construction of the models. In addition, a conceptual explanation is provided for the empirical or regression models formulated. The IEI and the associated models relating indoor environmental quality with the office occupant symptom index may be used as management tools, as illustrated with an example.

Overall dry deposition velocities of several elements were determined by dividing measured fluxes by measured airborne concentrations in different particle size ranges. The dry deposition measurements were made with a smooth surrogate surface on an automated dry deposition sampler (Eagle II) and the ambient particle concentrations were measured with a dichotomous sampler. These long-term measurements were made in Chicago, IL, South Haven, MI, and Sleeping Bear Dunes, MI, from December 1993 through October 1995 as part of the Lake Michigan Mass Balance Study. In general, the dry deposition fluxes of elements were highly correlated with coarse particle concentrations, slightly less well correlated with total particle concentrations, and least well correlated with fine particle concentrations. The calculated overall dry deposition velocities obtained using coarse particle concentrations varied from approximately 12 cm s−1 for Mg in Chicago to 0.2 cm s−1 for some primarily anthropogenic metals at the more remote sites. The velocities calculated using total particle concentrations were slightly lower. The crustal elements (Mg, Al, and Mn) had higher deposition velocities than anthropogenic elements (V, Cr, Cu, Zn, Mo, Ba and Pb). For crustal elements, overall dry deposition velocities were higher in Chicago than at the other sites.

As part of the Atmospheric Exchange Over Lakes and Oceans Study (AEOLOS) the dry deposition fluxes and atmospheric size distributions (ASDs) of anthropogenic metals were measured over the southern basin of Lake Michigan. The measurements were made during winter, summer, and fall, concurrently, in Chicago, IL; over Lake Michigan onboard the U.S. EPA RV Lake Guardian; and in South Haven, MI. The flux of Pb, Cu, and Zn was substantially higher in Chicago than in either South Haven or over Lake Michigan. The average measured Pb, Cu, and Zn fluxes were 0.07, 0.06, and 0.20 mg m-2 day-1 in Chicago; 0.003, 0.01, and 0.01 mg m-2 day-1 over Lake Michigan; and 0.004, 0.007, and 0.004 mg m-2 day-1 in South Haven. When the wind was from Chicago over the lake, the fluxes and concentrations measured over the lake were higher than when the wind was from other directions. In general, these anthropogenic metals had higher concentrations in the fine particle mode than in the coarse particle mode. Modeled and measured fluxes were in reasonable agreement. Coarse particles were found to be responsible for the majority of the flux at all locations., USEPA NERL Cooperative Agreement EPA/CR822046-0114