Search

The pre-fusion power operation (PFPO) phase of ITER, as described in the ITER research plan with Staged Approach,22 ITER Organization, “ITER Research Plan within the Staged Approach,” ITR-18–003, Aug. 2018. includes both hydrogen (H) and helium (He) plasma operations. In preparation for PFPO, both WEST and JET ran He plasma campaigns to study plasma-wall interactions in a tungsten environment. The campaigns included a back-and-forth transition between H or deuterium (D) and He plasma operation allowing the assessment of the achievable plasma content as well as the accessible wall reservoirs for respective species. The WEST changeovers included tokamak pulses with a fixed divertor configuration. The JET changeovers applied ion cyclotron wall conditioning (ICWC) and tokamak pulses including limiter phases and four different divertor configurations. Glow discharge conditioning (GDC) was applied to complete the changeovers. The results are characterized by subdivertor optical and mass spectrometric gas analyzers and spatially resolved optical emission spectroscopy. A He content of 96–97 % after H operations is achieved by tens of ICWC pulses (JET) and several dedicated diverted plasmas (WEST and JET), while a fivefold is estimated to be required for the back transition. Effective pumping of the wall released species is a key parameter for a fast changeover. Upon applying higher heating power, the relative content of the fueled plasma species decreases. The JET gas balance analysis indicates that He operation may increase H retention. WEST divertor spectroscopy indicates a larger He inventory near the inner divertor strike line. He GDC has a clear effect on the He recycling light at the WEST divertor while D GDC did not reduce the long lasting He content observed in D pulses after the JET He campaign.

This paper explores the plasma parameters of helium and hydrogen Ion Cyclotron Wall Conditioning (ICWC) discharges performed in JET as part of a He/H fuelling changeover experiment. The conducted study shows that plasma with a higher density is formed in helium than in hydrogen. A distinct glow in the ion cyclotron resonance zone is observed throughout the discharge in He. In H-ICWC discharges, a lower radio-frequency coupling efficiency and coupled power was observed than in He-ICWC discharges. While the helium concentration decreased with the number of H-ICWC pulses and the same for hydrogen in He-ICWC, which is the intended result of the plasma wall interaction in the ICWC changeover procedure, the main features of hydrogen as well as the helium IC discharge do not change dramatically.

Precise values for radiated energy in tokamak disruption experiments are needed to validate disruption mitigation techniques for burning plasma tokamaks like ITER and SPARC. Control room analysis of radiated power ( P _rad ) on JET assumes axisymmetry, since fitting 3D radiation structures with limited bolometry coverage is an under-determined problem. In mitigated disruptions, radiation is toroidally asymmetric and 3D, due to fast-growing 3D MHD modes and localized impurity sources. To address this problem, Emis3D adopts a physics motivated forward modeling (‘guess and check’) approach, comparing experimental bolometry data to synthetic data from user-defined radiation structures. Synthetic structures are observed with the Cherab modeling framework and a best fit chosen using a reduced χ ^2 statistic. 2D tomographic inversion models are tested, as well as helical flux tubes and 3D MHD simulated structures from JOREK. Two nominally identical pure neon shattered pellet injection (SPI) mitigated discharges in JET are analyzed. 2D tomographic inversions with added toroidal freedom are the best fits in the thermal quench (TQ) and current quench (CQ). In the pre-TQ, 2D reconstructions are statistically the best fits, but are likely over-optimized and do not capture the 3D radiation structure seen in fast camera images. The next-best pre-TQ fits are helical structures that extend towards the high-field side, consistent with an impurity flow under the magnetic nozzle effect also observed in JOREK simulations. Whole-disruption radiated fractions of $ 0.98 +0.03/ $ $ -0.29 $ and $ 1.01 +0.02/-0.17 $ are found, suggesting that the stored energy may have been fully mitigated by each SPI, although mitigation efficiencies well below ITER and SPARC requirements for high energy pulses are still within the large uncertainties. Emis3D is also used to validate JOREK SPI simulations, and confirms improvements in matching experiment from changes to impurity modeling. Time-dependent toroidal peaking factors are calculated and discussed.

The pre-thermal quench (pre-TQ) dynamics of a pure deuterium ( $\mathrm{D}_2$ ) shattered pellet injection (SPI) into a $3\,\mathrm{MA}$ / $7\,\mathrm{MJ}$ JET H-mode plasma is studied via 3D non-linear MHD modelling with the JOREK code. The interpretative modelling captures the overall evolution of the measured density and radiated power. The simulations also identify the importance of the drifts of ablation plasmoids towards the tokamak low field side (LFS) and the impurities in the background plasma in fragment penetration, assimilation, radiative cooling and MHD activity in $\mathrm{D}_2$ SPI experiments. It is found that plasmoid drifts lead to an about 70% reduction of the central line-integrated density (compared to a simulation without drifts) in the JET $\mathrm{D}_2$ SPI discharge considered. Impurities that pre-exist before the SPI as well as those from possible impurity influxes related to the SPI are shown to dominate the radiation in the considered discharge. With inputs from JOREK simulations, modelling with the Lagrangian particle-based pellet code PELOTON reproduces the deviation of the SPI fragments in the direction of the major radius as observed by the fast camera. This confirms the role of rocket effects and plasmoid drifts in the considered discharge and reinforces the validity of the JOREK modelling. The limited core density rise due to plasmoid drifts and the strong radiative cooling and MHD activity with impurities (depending on their species and concentration) could limit the effectiveness of LFS $\mathrm{D}_2$ SPI in runaway electron avoidance and are worth considering in the design of the ITER disruption mitigation system.

The JET-ILW pure tritium and deuterium–tritium (DTE2) experimental campaigns took place in 2021–2022. Tritium (T) and deuterium–tritium (D–T) operations present challenges not encountered in present day tokamaks (Horton et al 2016 Fusion Eng. Des. 109–111 925–36). This contribution focuses on ion cyclotron resonance heating (ICRH) operations in tritium and deuterium–tritium plasmas, starting with a summary of the program of improvements to the ICRH system which spanned a few years prior to these experiments. Procedures were implemented to address specific constraints from tritium and deuterium–tritium operations (tritium safety and reduced access to the RF generator area) and increase the system reliability and power availability during plasma pulses. Operation of the upgraded real time RF power control system that maximises the launched power while taking into account limitations from the system or antenna coupling is described. We also report on the result from dedicated pulses performed to assess the potential harmful impact of the 2nd harmonic tritium resonance in the plasma, close to the inner wall, when using the standard central hydrogen minority ICRH scheme. During DTE2, the ITER-like antenna was not used because water leaked from an in-vessel capacitor into the vessel on day-2 of the experimental campaign. The lessons learnt from this incident are highlighted. Finally, the ICRH plant adjustments required to safely perform ion cyclotron wall cleaning discharges are described.

A baseline scenario of deuterium–tritium (D–T) plasma with peripheral high-field-side fuelling pellets has been produced in JET in order to mimic the situation in ITER. The isotope mix ratio is controlled in order to target the value of 50%–50% by a combination of tritium gas puffing and deuterium pellet injection. Multiple factors controlling the fuelling efficiency of individual pellets are analysed, with the following findings: (1) prompt particle losses due to pellet-triggered edge-localised modes (ELMs) are detected, (2) the plasmoid drift velocity might be smaller than that predicted by simulation, (3) post-pellet particle loss is controlled by transient phases with ELMs.The overall pellet particle flux normalised to the heat flux is similar to that in previous pellet fuelling experiments in AUG and JET.

The paper reports the first demonstration of in situ laser-induced desorption — quadrupole mass spectrometry (LID-QMS) application on a large scale fusion device performed in summer 2023. LID-QMS allows direct measurements of the fuel inventory of plasma facing components without retrieving them from the fusion device. The diagnostic desorbs the retained gases by heating a 3 mm diameter spot on the wall using a 1 ms long laser pulse and detects them by QMS. Thus, it can measure the gas content at any wall position accessible to the laser. The successful LID-QMS application in laboratory scale and on medium size fusion devices has now been demonstrated on the larger scale and it is already foreseen as tritium monitor diagnostic in ITER. This in situ diagnostic gives direct access to retention physics on a short timescale instead of campaign-integrated measurements and can assess the space-resolvedefficacy of detritation methods. LID-QMS can be applied on many materials: on Be deposits like in JET, B deposits like in TEXTOR, C based materials or on bulk-W.

The Joint European Torus (JET) fusion reactor was upgraded to the metallic wall configuration in 2011 which consisted of bulk beryllium (Be) tiles in the main chamber and bulk tungsten (W) and W-coated CFC tiles in the divertor (Matthews G.F. et al 2011 Phys. Scr. T148 014001). During each campaign, a series of wall damages were observed; on the upper dump plates (UDP) positioned to the top part of the vessel walls and on the inner wall—mainly affecting the inner wall guard limiters (IWGL). In both cases, it was concluded that the causes of these damages were unmitigated plasma disruptions. In the case of JET with the metallic wall configuration, most of these plasma disruptions were intentionally provoked. The overall objective was to study the behaviour of these phenomena, in order to assess their impact on the wall, improve understanding of morphological material changes, and—based on that—to develop, implement and test mitigation techniques for their prospective use on ITER. The current results bring additional information on the effects of the unmitigated plasma disruptions on the UDPs and are a significant extension of work presented in (Jepu et al 2019 Nucl. Fusion 59 086009) where the scale of the damage after three operational campaigns on the Be top limiters of JET was highlighted. In addition, new data is presented on the damaging effect that the high energetic runaway electrons had on the Be IWGL in JET.

A new H-mode regime at low density and low edge safety factor ( q _95 = 3.2, with $I_\mathrm{p}$ = 3 MA) that combines high energy confinement, stationary conditions for density and radiation and small Edge Localized Modes (ELMs) have been found in JET with Be/W wall. Such a regime is achieved by operating without external gas puffing, leading to a decrease in the edge density and a substantial increase in rotation and ion temperature in both the pedestal and the core region. Transport modelling shows a reduction of the turbulence, which starts in the pedestal region and extends into the plasma core, and outward impurity convection, consistent with the improved energy confinement and the lack of W accumulation observed in those conditions. In addition, large type I ELMs, typically found in gas-fuelled plasmas, are replaced by smaller and more frequent ELMs, whose appearance is correlated with a substantial reduction of the pedestal density and its gradient. Pedestals in this operating regime are stable to peeling–ballooning modes, consistent with the lack of large ELMs. This is in contrast to results in unfuelled JET-C plasmas that typically operated at higher pedestal densities and developed low frequency, large type I ELMs, thus pointing to the low density as one of the critical parameters for accessing this small ELMs regime in JET. This small ELMs regime exhibits the same low pedestal collisionality ( $\nu_{\mathrm{e},\mathrm{ped}}^*\sim0.1$ ) expected in ITER and operates at low q _95 , thus making it different from other small ELMs regimes that are typically obtained at higher q _95 and higher pedestal collisionality. These features make this newly developed H-mode regime in JET with Be/W wall a valuable tool for exploring the underlying transport, the different mechanisms of turbulence stabilization, as well as the physics associated with the appearance of small ELMs in high-temperature plasmas at ITER relevant pedestal collisionality.

The publication provide further insights into the dynamics of JET runaway electron (RE) beams mitigated by D2-rich shattered pellet injection (SPI) (Reux et al 2022 Plasma Phys. Control. Fusion 64 034002). Multi-diagnostic analyses show that mechanisms causing continuous RE losses and energy transfer from hot electrons to cold background plasma can act before the SPI. After the SPI, measurements are compatible with a reduction of the maximum energy and pitch angle of the RE distribution while the population of supra-thermal electrons increases. The RE population growth is likely due to electron avalanche. Dark island-like pattern chains, characterised by an integer poloidal mode number and a certain minor radius, are identified in the JET RE beam synchrotron radiation videos. The synchrotron island dynamics is studied via a newly developed computer vision code (Sommariva and Silburn https://c4science.ch/source/pSpiPTV/ ). The radial motion of synchrotron island chains is found to be consistent with the most plausible time evolution of the radial current density profile compatible with both the RE synchrotron videos and the total RE current time trace. Similarly, correlations are identified between the temporal progression of the synchrotron islands poloidal rotation frequency and sudden MHD relaxation events. Loss-of-RE events probably caused by non-linear interactions between synchrotron islands are observed for the first time. Experimental evidences suggest that synchrotron islands are possibly related to the existence of magnetic islands which may lead to the development of new RE beam mitigation strategies.

For its initial operational phase, ITER has until recently considered using non-nuclear hydrogen (H) or helium (He) plasmas to keep nuclear activation at low levels. To this end, the Tokamak Exploitation Task Force of the EUROfusion Consortium carried out dedicated experimental campaigns in He on the ASDEX Upgrade (AUG) and JET tokamaks in 2022, with particular emphasis put on the ELMy H-mode operation and plasma-wall interaction processes as well as comparison to H or deuterium (D) plasmas. Both in pure He and mixed He + H plasmas, H-mode operation could be reached but more effort was needed to obtain a stable plasma scenario than in H or D. Even if the power threshold for the LH transition was lower in He, entering the type-I ELMy regime appeared to require equally much or even more heating power than in H. Suppression of ELMs by resonant magnetic perturbations was studied on AUG but was only possible in plasmas with a He content below 19%; the reason for this unexpected behaviour remains still unclear and various theoretical approaches are being pursued to properly understand the physics behind ELM suppression. The erosion rates of tungsten (W) plasma-facing components were an order of magnitude larger than what has been reported in hydrogenic plasmas, which can be attributed to the prominent role of He ^2+ ions in the plasma. For the first time, the formation of nanoscale structures (W fuzz) was unambiguously demonstrated in H-mode He plasmas on AUG. However, no direct evidence of fuzz creation on JET was obtained despite the main conditions for its occurrence being met. The reason could be a delicate balance between W erosion by ELMs, competition between the growth and annealing of the fuzz, and coverage of the surface with co-deposits.

JET, the world’s largest operating tokamak with unique Be/W wall and tritium handling capability, completed a Deuterium-Tritium (D-T) campaign in 2021 (Maggi et al 29th Fusion Energy Conf. ) following a decade of preparatory experiments, dedicated enhancements, technical rehearsals and training (Horton et al 2016 Fusion Eng. Des. 109–111 925). Operation with tritium raises significant technical, safety and scientific challenges not encountered in standard protium or deuterium operation. This contribution describes the tritium operational requirements, pulses and technical preparations, new operating procedures, lessons learned and details on the achieved operational availability and performance. The preparation and execution of the recent JET tritium experiments benefitted from the previous experience in 1991 (Preliminary Tritium Experiment), 1997 (DTE1 campaign) and 2003 (Trace Tritium Campaigns) and consisted of the following five phases: technical rehearsals and scenario preparation, tritium commissioning, 100% tritium campaign, D-T campaign (DTE2), tritium clean-up. Following the clean-up JET resumed normal operation and is currently undertaking a further D-T campaign (DTE3).

This paper reports the first experiment carried out in deuterium–tritium addressing the integration of a radiative divertor for heat-load control with good confinement. Neon seeding was carried out for the first time in a D–T plasma as part of the second D–T campaign of JET with its Be/W wall environment. The technical difficulties linked to the re-ionisation heat load are reported in T and D–T. This paper compares the impact of neon seeding on D–T plasmas and their D counterpart on the divertor detachment, localisation of the radiation, scrape-off profiles, pedestal structure, edge localised modes and global confinement.

Measurements of the ion currents to and plasma conditions at the low-field side (LFS) divertor target plate in low-confinement mode plasmas in the JET ITER-like wall materials configuration show that the core plasma density required to detach the LFS divertor plasma is independent of the hydrogenic species protium, deuterium and tritium, and a 40 %/60 % deuterium–tritium mixture. This observation applies to a divertor plasma configuration with the LFS strike line connected to the horizontal part of the LFS divertor chosen because of its superior diagnostic coverage. The finding is independent of the operational status of the JET cryogenic pump. The electron temperature (Te) at the LFS strike line was markedly reduced from 25 eV to 5 eV over a narrow range of increasing core plasma density, and observed to be between 2 eV and 3 eV at the onset of detachment. The electron density (ne) peaks across the LFS plasma when Te at the target plate is 1 eV, and spatially moves to the X-point for higher core densities. The density limit was found approximately 20 % higher in protium than in tritium and deuterium–tritium plasmas.

The total radiated fraction is examined in high density H-mode plasmas (Greenwald fraction of about 85 %) in JET by the variation of the auxiliary heating power of Pheat = 14 MW-29 MW. An achieved radiation fraction of about 75 % at most has been observed in JET-ILW, which is less than the highest achievable (≈90 %) fraction in JET-C during the high radiative power scenarios with N2 seeding. It is shown that the maximal achievable total radiation fraction averaged over ELM cycles has a strong dependence on the radiation efficiency of the ELM energy, θrad: γrad,totalmax=1-fELM×ΔWELMPheat1-θrad. About 50 % and 16 % of the ELM induced diamagnetic energy drop (ΔWELM) radiates during the ELM in JET-C and JET-ILW, respectively, which corresponds to the maximum total radiated powers of γrad,JET-Cmax=0.87 and γrad,JET-ILWmax=0.77. These values of the maximum of the radiative power fractions are in good agreement with γradmax experimentally observed in JET-C (90 %) and JET-ILW (75 %).

The JET hybrid scenario has been developed from low plasma current carbon wall discharges to the record-breaking Deuterium-Tritium plasmas obtained in 2021 with the ITER-like Be/W wall. The development started in pure Deuterium with refinement of the plasma current, and toroidal magnetic field choices and succeeded in solving the heat load challenges arising from 37 MW of injected power in the ITER like wall environment, keeping the radiation in the edge and core controlled, avoiding MHD instabilities and reaching high neutron rates. The Deuterium hybrid plasmas have been re-run in Tritium and methods have been found to keep the radiation controlled but not at high fusion performance probably due to time constraints. For the first time this scenario has been run in Deuterium-Tritium (50:50). These plasmas were re-optimised to have a radiation-stable H-mode entry phase, good impurity control through edge T _i gradient screening and optimised performance with fusion power exceeding 10 MW for longer than three alpha particle slow down times, 8.3 MW averaged over 5 s and fusion energy of 45.8 MJ.

The reference ion cyclotron resonance frequency (ICRF) heating schemes for ITER deuterium–tritium (D-T) plasmas at the full magnetic field of 5.3 T are second harmonic heating of T and ^3 He minority heating. The wave-particle resonance location for these schemes coincide and are central at a wave frequency of 53 MHz at 5.3 T. Experiments have been carried out in the second major D-T campaign (DTE2) at JET, and in its prior D campaigns, to integrate these ICRF scenarios in JET high-performance plasmas and to compare their performance with the commonly used hydrogen (H) minority heating. In 50:50 D:T plasmas, up to 35% and 5% larger fusion power and diamagnetic energy content, respectively, were obtained with second harmonic heating of T as compared to H minority heating at comparable total input powers and gas injection rates. The core ion temperature was up to 30% and 20% higher with second harmonic T and ^3 He minority heating, respectively, with respect to H minority heating. These are favourable results for the use of these scenarios in ITER and future fusion reactors. According to modelling, adding ICRF heating to neutral beam injection using D and T beams resulted in a 10%–20% increase of on-axis bulk ion heating in the D-T plasmas due to its localisation in the plasma core. Central power deposition was confirmed with the break-in-slope and fast Fourier transform analysis of ion and electron temperature in response to ICRF modulation. The tail temperature of fast ICRF-accelerated tritons, their enhancement of the fusion yield and time behaviour as measured by an upgraded magnetic proton recoil spectrometer and neutral particle analyser were found in agreement with theoretical predictions. No losses of ICRF-accelerated ions were observed by fast ion detectors, which was as expected given the high plasma density of n _e ≈ 7–8 × 10 ^19 m ^−3 in the main heating phase that limited the formation of ICRF-accelerated fast ion tails. ^3 He was introduced in the machine by ^3 He gas injection, and the ^3 He concentration was measured by a high-resolution optical penning gauge in the sub-divertor region. The DTE2 experiments with ^3 He minority heating were carried with a low ^3 He concentration in the range of 2%–4% given the fact that the highest neutron rates with ^3 He minority heating in D plasmas were obtained at low ^3 He concentrations of ∼2%, which also coincided with the highest plasma diamagnetic energy content. In addition to ^3 He introduced by ^3 He gas injection, an intrinsic concentration of ^3 He of the order of 0.2%–0.4% was measured in D-T plasmas before ^3 He was introduced in the device, which is attributed to the radioactive decay of tritium to ^3 He. According to modelling, even such low intrinsic concentrations of ^3 He lead to significant changes in ICRF power partitioning during second harmonic heating of T due to absorption of up to 30% of the wave power by ^3 He.

After the second Deuterium–Tritium Campaign (DTE2) in the JET tokamak with the ITER-Like Wall (ILW) and full tritium campaigns that preceded and followed after the DTE2, a sequence of fuel recovery methods was applied to promote tritium removal from wall components. The sequence started with several days of baking of the main chamber walls at 240 °C and at 320 °C. Subsequently, baking was superimposed with Ion-Cyclotron Wall Conditioning (ICWC) and Glow Discharge Conditioning (GDC) cleaning cycles in deuterium. Diverted plasma operation in deuterium with different strike point configurations, including a Raised Inner Strike Point (RISP) configuration, and with different plasma heating—Ion Cyclotron Resonance Frequency (ICRF) and Neutral Beam Injection (NBI)—concluded the cleaning sequence. Tritium content in plasma and in the pumped gas was monitored throughout the experiment. The applied fuel recovery methods allowed reducing the residual tritium content in deuterium NBI-heated plasmas to about 0.1% as deduced from neutron rate measurements. This value is well below the requirement of 1% set by the maximum 14 MeV fusion neutron budget allocated in the ensuing deuterium plasma campaign. The quantified tritium removal over the course of the experiment was $\left( {13.4 \pm 0.7} \right) \times {10^{22}}$ atoms or $\left( {0.67 \pm 0.03} \right)$ g with ∼58% attributed to baking, ∼12.5% to ICWC, ∼26% to GDC, and ∼3.5% to first low power RISP plasmas. The experimentally estimated amount of removed tritium is in good agreement with long-term tritium accounting by the JET tritium reprocessing plant, in which the unaccounted amount was reduced by $0.71$ g after the cleaning experiment.

While current tokamak experiments are beginning to use real-time feedback control systems to manage the plasma exhaust, future tokamaks still require validation of theoretical models used to predict the threshold impurity concentration required to sufficiently reduce the power and particle fluxes to the divertor. This work exploits new spectroscopic measurements of the divertor nitrogen concentration, cN, in partially detached N2-seeded H-mode plasmas on ASDEX Upgrade (AUG) and JET with the ITER-Like Wall (JET-ILW) to test the parameter dependencies of the power flowing to the outer divertor, Pdiv,outer, and the separatrix electron density, ne,sep. A least-squares regression of the AUG measurements demonstrates that the threshold cN required for detachment scales as cN∝Pdiv,outer1.19±0.32ne,sep-2.77±0.36. This scaling of ne,sep is also consistent with the measurements from JET which, at constant Pdiv,outer, show cN∝ne,sep-2.43±0.27. The dependencies of Pdiv,outer and ne,sep is demonstrated over at least a factor of two change in both parameters and indicates a stronger dependence on ne,sep in comparison to the Lengyel model, which could be due to the assumption in this model that the heat flux channel width is independent of density. This first assessment of detachment scaling with impurity seeding highlights the need for further analysis of the systematic uncertainties of the measurement and more consistent scenarios from more tokamaks to investigate the machine size scaling.

High speed visible imaging allows to visualize the 2-dimensional dynamics of fast phenomena in the boundary layer of fusion plasmas. Here we describe the two high speed visible cameras currently operating in the JET tokamak, enabling the simultaneous observation of a large fraction of the JET tokamak vacuum vessel with the appropriate configuration for many different plasma phenomena. As an example we discuss recent observations on the spatial and temporal dynamics of visible emission at the outer wall during Edge Localized Modes (ELMs) and the penetration of Shattered Injected Pellet (SPI) into the plasma.

Tungsten (W) melting due to transient power loads, for example those delivered by edge localised modes (ELMs), is a major concern for next step fusion devices. A series of experiments has been performed on JET to investigate the dynamics of Type-I ELM-induced transient melting. Following initial exposures in 2013 of a W-lamella with sharp leading edge in the bulk W outer divertor, new experiments have been performed in 2016–2017 on a protruding W-lamella with a 15° slope, allowing direct and spatially resolved (0.85 mm/pixel) observation of the top surface using the IR thermography system viewing from the top of the poloidal cross-section. Thermal and IR analysis have already been conducted assuming the geometrical projection of the parallel heat flux on the W-lamellas, thus ignoring the gyro-radius orbit of plasma particles. Although it is well justified during L-mode or inter-ELM period, the hypothesis becomes questionable during ELM when the ion Larmor radius is larger. The goal of this paper is to extend the previous analysis based on the forward approach to the H-mode discharges and investigate in particular the gyro-radius effect during the Type-I ELMs, those used to achieve transient melting on the slope of the protruding W-lamella. Surface temperatures measured by the IR camera are compared with reconstructed synthetic data from 3D thermal modelling using heat loads derived from optical projection of the parallel heat flux (ignoring the gyro-radius orbit), 2D gyro-radius orbit and particle-in-cell (PIC) simulations describing the influence of finite Larmor-radius effects and electrical potential on the deposited power flux. Results show that the ELM power deposition behaves differently than the optical projection of the parallel heat flux, contrary to the L-mode observations, and may thus be due to the much larger gyro-orbits of the energetic ELM ions in comparison to L-mode or inter-ELM conditions. Keywords: ELM heat flux analysis, Optical projection, PIC modelling, Ion orbit modelling, IR data, Spatial resolution effect

In this paper we discuss results from the study of the energy balance in JET based on calculated heating energies, radiated energy from bolometry and tile calorimetry. Recent data enables us to be more confident in the numbers used and to exclude certain possibilities but the overall energy imbalance which typically amounts to 25% of total input remains unexplained. This shows that caution is required in interpreting fractional radiated powers which are commonly used to measure the effectiveness of impurity seeded scenarios at reducing divertor heat load. Keywords: ILW, JET

Using footage from high speed movies taken of the boundary plasma in the Mega Amp Spherical Tokamak (MAST) general properties of filaments are inferred through statistical moments. Filaments are observed up to and beyond the ψN=1.5 flux surface which, in single null configurations, lies well beyond the secondary separatrix and leads to filaments observed > 30cm from the top of the plasma. In the divertor filaments are observed to connect through to the target, however a quiescent region is observed close to the X-point where no coherent filaments are identified. This region coincides with a sharp rise in the integrated magnetic shear which may change the nature of the filament cross-section.

For simulation of plasma-facing component erosion in fusion experiments, an analytical expression for the ion velocity just before the surface impact including the local electric field and an optional surface biasing effect is suggested. Energy and angular impact distributions and the resulting effective sputtering yields were produced for several experimental scenarios at JET ILW mostly involving PFCs exposed to an oblique magnetic field. The analytic solution has been applied as an improvement to earlier ERO modelling of localized, Be outer limiter, RF-enhanced erosion, modulated by toggling of a remote, however magnetically connected ICRH antenna. The effective W sputtering yields due to D and Be ion impact in Type-I and Type-III ELMs and inter-ELM conditions were also estimated using the analytical approach and benchmarked by spectroscopy. The intra-ELM W sputtering flux increases almost 10 times in comparison to the inter-ELM flux. Keywords: Plasma-surface interaction, JET, ITER-like wall, Beryllium, Erosion, Oblique magnetic field, Electric field, ELM

A global heat flux model based on a fractional derivative of plasma pressure is proposed for the heat transport in fusion plasmas. The degree of the fractional derivative of the heat flux, α, is defined through the power balance analysis of the steady state. The model was used to obtain the experimental values of α for a large database of the Joint European Torus (JET) carbon-wall as well as ITER like-wall plasmas. The fractional degrees of the electron heat flux are found to be α

Introduction: Early detection of developmental difficulties is universally considered a necessary public health measure, with routine developmental monitoring an important function of primary healthcare services. This study aimed to describe the developmental monitoring practice in two remote Australian Aboriginal primary healthcare services and to identify gaps in the delivery of developmental monitoring services. Methods: A cross-sectional baseline medical record audit of all resident children aged less than 5 years in two remote Aboriginal health centres in the Northern Territory (NT) in Australia was undertaken between December 2010 and November 2011. Results: A total of 151 medical records were audited, 80 in Community A and 71 in Community B. Developmental checks were more likely among children who attended services more regularly. In Community A, 63 (79%) medical records had some evidence of a developmental check and in Community B there were 42 (59%) medical records with such evidence. However, there was little indication of how assessments were undertaken: only one record noted the use of a formal developmental screening measure. In Community A, 16 (16%) records documented parent report and 20 (20%) documented staff observations, while in Community B, the numbers were 2 (3%) and 11 (19%), respectively. The overall recorded prevalence of developmental difficulties was 21% in Community A and 6% in Community B. Conclusions: This is the first study to describe the quality of developmental monitoring practice in remote Australian Aboriginal health services. The audit findings suggest the need for a systems-wide approach to the delivery and recording of developmental monitoring services. This will require routine training of remote Aboriginal health workers and remote area nurses in developmental monitoring practice including the use of a culturally appropriate, structured developmental screening measure. [ABSTRACT FROM AUTHOR]

For the first time, the JET operation in deuterium–tritium (D–T) plasma, which is scheduled to take place on JET in 2020, will be performed in the ITER mix of plasma-facing component materials. In view of the preparation of the DT campaign (DTE2), several aspects of the plasma operation require significant improvements, such as a real-time protection of the first wall. The risk of damaging the metallic PFCs caused by beryllium melting or cracking of tungsten owing to thermal fatigue required a new reliable D–T compatible active protection system. Therefore, the future development of the JET real time first wall protection is focused on the D–T campaign and the ITER relevant conditions which may cause failure of camera electronics within the Torus hall. In addition to the technological aspect, the intensive preparation of the diverse software tools and real time algorithms for hot spot detection as well as alarm handling strategy required for the wall protection is in progress. This contribution describes the improved design, implementation, and operation of the near infrared (NIR) imaging diagnostic system of the JET-ILW plasma experiment and its integration into the existing JET protection architecture. To provide the reliable wall protection during the DTE2, two more sensitive logarithmic NIR camera systems equipped with new optical relays to take images and cameras outside of the biological shield have been installed on JET-ILW and calibrated with an in-vessel calibration light source (ICLS). Additionally, post-pulse data visualization and advanced analysis of all types of imaging data is provided by the new software framework JUVIL (JET users video imaging library). The formation of hot spots is recognized as a significant threat due to rapid surface temperature rise. Because it could trigger the protection system to stop a pulse, it is important to identify the mechanisms and conditions responsible for the formation of such hot spots. To address this issue the new software tool ‘Hotspot Editor’ has been developed. [ABSTRACT FROM AUTHOR]

Parallel heat flux calculations at the JET divertor have been based on the assumption that all incoming heat is due to the projection of the heat flux parallel to the magnetic line, , plus a constant background. This simplification led to inconsistencies during the analysis of a series of dedicated tungsten melting experiments performed in 2013, for which infrared (IR) thermography surface measurements could not be recreated through simulations unless the parallel heat flux was reduced by 80% for L-mode and 60% for H-mode. We give an explanation for these differences using a new IR inverse analysis code, a set of geometrical corrections, and most importantly an additional term for the divertor heat flux accounting for non-parallel effects such as cross-field transport, recycled neutrals or charge exchange. This component has been evaluated comparing four different geometries with impinging angles varying from 2 to 90°. Its magnitude corresponds to 1.2%–1.9% of , but because it is not affected by the magnetic projection, it accounts for up to 20%–30% of the tile surface heat flux. The geometrical corrections imply a further reduction of 24% of the measured heat flux. In addition, the application of the new inverse code increases the accuracy of the tile heat flux calculation, eliminating any previous discrepancy. The parallel heat flux computed with this new model is actually much lower than previously deduced by inverse analysis of IR temperatures—40% for L-mode and 50% for H-mode—while being independent of the geometry on which it is measured. This main result confirms the validity of the optical projection as long as a non-constant and non-parallel component is considered. For a given total heating power, the model predicts over 10% reduction of the maximum tile surface heat flux compared to strict optical modelling, as well as a 30% reduced sensitivity to manufacturing and assembling tolerances. These conclusions, along with the improvement in the predictability of the divertor thermal behaviour, are critical for JET future DT operations, and are also directly applicable to the design of the ITER divertor monoblocks. [ABSTRACT FROM AUTHOR]

Neutral deuterium gas puffing at the high field side of the mega ampere spherical tokamak (MAST) is shown to drive carbon impurity flows that are aligned with the trajectory of the magnetic field lines in the plasma scrape-off-layer. These impurity flows were directly imaged with emissions from C2+ ions at MAST by coherence imaging spectroscopy and were qualitatively reproduced in deuterium plasmas by modeling with the EMC3-EIRENE plasma edge fluid and kinetic neutral transport code. A reduced one-dimensional momentum and particle balance shows that a localized increase in the static plasma pressure in front of the neutral gas puff yields an acceleration of the plasma due to local ionization. Perpendicular particle transport yields a decay from which a parallel length scale can be determined. Parameter scans in EMC3-EIRENE were carried out to determine the sensitivity of the deuterium plasma flow phenomena to local fueling and diffusion parameters and it is found that these flows robustly form across a wide variety of plasma conditions. Finally, efforts to couple this behavior in the background plasma directly to the impurity flows observed experimentally in MAST using a trace impurity model are discussed. These results provide insight into the fueling and exhaust features at this pivotal point of the radial and parallel particle flux balance, which is a major part of the plasma fueling and exhaust characteristics in a magnetically confined fusion device. [ABSTRACT FROM AUTHOR]

The design and operation of future fusion devices relying on H-mode plasmas requires reliable modelling of edge-localized modes (ELMs) for precise prediction of divertor target conditions. An extensive experimental validation of simple analytical predictions of the time evolution of target plasma loads during ELMs has been carried out here in more than 70 JET-ITER-like wall H-mode experiments with a wide range of conditions. Comparisons of these analytical predictions with diagnostic measurements of target ion flux density, power density, impact energy and electron temperature during ELMs are presented in this paper and show excellent agreement. The analytical predictions tested here are made with the ‘free-streaming’ kinetic model (FSM) which describes ELMs as a quasi-neutral plasma bunch expanding along the magnetic field lines into the Scrape-Off Layer without collisions. Consequences of the FSM on energy reflection and deposition on divertor targets during ELMs are also discussed. [ABSTRACT FROM AUTHOR]

L to H transition studies at JET have revealed an n  =  0, m  =  1 magnetic oscillation starting immediately at the L to H transition (called M-mode for brevity). While the magnetic oscillation is present a weak ELM-less H-mode regime is obtained, with a clear increase of density and a weak electron temperature pedestal. It is an intermediate state between L and H-mode. In ICRH heated plasmas or low density NBI plasmas the magnetic mode and the pedestal can remain steady (with small oscillations) for the duration of the heating phase, of order 10 s or more. The axisymmetric magnetic oscillation has period ~0.5–2 ms, and poloidal mode number m  =  1: it looks like a pedestal localised up/down oscillation, although it is clearly a natural oscillation of the plasma, not driven by the position control system. Electron cyclotron emission, interferometry, reflectometry and fast Li beam measurements locate the mode in the pedestal region. Dα, fast infrared camera and Langmuir probe measurements show that the mode modulates heat and particle fluxes to the target. The mode frequency appears to scale with the poloidal Alfvén velocity, and not with sound speed (i.e. it is not a geodesic acoustic mode). A heuristic model is proposed for the frequency scaling of the mode. We discuss the relationship between the M-mode and other related observations near the L–H transition. [ABSTRACT FROM AUTHOR]

In 2007, Australia introduced its most radical welfare reform in recent history, targeting Aboriginal communities with the aim of protecting children from harm. The 'income management' policy forced Aboriginal welfare recipients to spend at least half of their government transfers on essentials (e.g. food, housing), and less on non-essentials (e.g. alcohol, tobacco). By exploiting its staggered rollout, we estimate the impact of in utero exposure to the policy rollout on birthweight. We find that exposure to the income management policy reduced average birthweight robustly by 85 g and increased the risk of low birth weight by 3 percentage points. This finding is not explained by behavioral change (fertility, maternal risk behavior, access to care), or survival probabilities of at-risk fetuses. More likely, a lack of policy implementation planning and infrastructure led to acute income insecurity and stress during the rollout period, exacerbating the existing health inequalities it sought to address., (Copyright © 2022. Published by Elsevier B.V.)

Purpose: We aimed to test the reliability and validity of two brief measures of resilience adopted for the evaluation of a preventative social-emotional curriculum implemented for Aboriginal middle school students from socially disadvantaged remote communities in Australia's Northern Territory. The questionnaires chosen were intended to measure psychological resilience and socio-cultural resilience as complementary dimensions of the capacity to cope in circumstances of significant life stress and risk of self-harm., Methods: Confirmatory factor analysis (CFA) was conducted to assess construct validity of the 10-item Connor-Davidson Resilience Scale (CD-RISC-10), a measure of psychological resilience, and the 12-item Child and Youth Resilience Measure (CYRM-12), a measure of socio-cultural resilience, with a sample of 520 students. Associations between resilience and psychological distress and emotional and behavioural difficulty were analysed in relation to life stressors to assess criterion validity of the scales., Results: CFA provided support for the validity of the respective constructs. There was good fit for both scales. However, assessment of criterion validity of the scales suggested that the adapted measure of socio-cultural resilience (CYRM-12NT) showed higher reliability and a clearer indication of predictive validity than the measure of psychological resilience (CD-RISC-10)., Conclusions: The CYRM-12NT appears to be a more useful measure of resilience among Aboriginal youth exposed to significant life stress and disadvantage. However, both measures may require further development to enhance their validity and utility among potentially at-risk adolescents in socially, culturally and linguistically diverse remote Aboriginal communities., Competing Interests: RM is currently employed at Perth Psychological Services, but was not at the time the study was conducted. This does not alter our adherence to PLOS ONE policies on sharing data and materials. There are no patents, products in development or marketed products associated with this research to declare.

For the first time it is experimentally demonstrated on the JET tokamak that a combination of a low impurity concentration bulk plasma and large magnetohydrodynamic instabilities is able to suppress relativistic electron beams without measurable heat loads onto the plasma facing components. Magnetohydrodynamic simulations of the instability and modeling of the postinstability plasma confirm the prompt loss of runaways and the absence of regeneration during the final current collapse. These surprising findings motivate a new approach to dissipate runaway electrons generated during tokamak plasma disruptions.

Background: Rates of hospital admission for suicide-related thoughts and behaviors (SRTBs) are elevated in the Northern Territory (NT) of Australia, especially by Aboriginal people, but very little is known about emergency department (ED) presentations. Aim: We aimed to profile ED presentations in the NT involving SRTBs by Indigenous status and compare discharge arrangements. Method: Logistic regression analyses were performed on data from electronic patient records of consecutive ED presentations involving SRTBs. Results: During the study period, 167 presentations were observed. Aboriginal patients were more likely to present from remote areas and to report substance misuse and family conflict or violence compared with non-Aboriginal patients. In both groups, males were more likely than females to be admitted as were persons presenting with self-harm compared with those who had suicidal thoughts only. No differences in discharge arrangements were identified by Indigenous status. Limitations: The small scale of the study and use of administrative records points to the need for further research to improve the quality of the evidence. Conclusion: While presentations by high-risk groups are more likely to be admitted for further care, the assessment of psychosocial risks and needs in EDs is vital to informing decisions for aftercare that support recovery in the community for Aboriginal patients and patients discharged from EDs.

A robust impurity detection and tracking code, able to generate large sets of dust tracks from tokamak camera footage, is presented. This machine learning-based code is tested with cameras from the Joint European Torus, Doublet-III-D, and Magnum-PSI and is able to generate dust tracks with a 65-100% classification accuracy. Moreover, the number dust particles detected from a single camera shot can be up to the order of 1000. Several areas of improvement for the code are highlighted, such as generating more significant training data sets and accounting for selection biases. Although the code is tested with dust in single two-dimensional camera views, it could easily be applied to multiple-camera stereoscopic reconstruction or nondust impurities.

Background: Previous studies have reported a high prevalence of chronic otitis media (OM) and hearing impairment (HI) in Aboriginal children in the Northern Territory (NT) of Australia. Children affected by these disorders are believed to be at increased risk for adverse outcomes in early childhood development, school attendance, academic performance, and child maltreatment and youth offending. However, to date, there have been no studies quantifying the association between HI and these outcomes in this population., Objective: This study will investigate the association between HI and the 5 outcomes in Aboriginal children living in remote NT communities., Methods: Individual-level information linked across multiple administrative datasets will be used to conduct a series of retrospective observational studies on selected developmental and school outcomes. The predictor variables for all studies are the results from audiometric hearing assessments. The outcome measures are as follows: Australian Early Development Census results, representing developmental readiness for school, assessed around 5 years of age; Year 1 school attendance rates; Year 3 school-based academic performance, assessed in the National Assessment Program-Literacy and Numeracy; incidence of child maltreatment events (including both notifications and substantiated cases); and incidence of a first guilty verdict for youth offenders. Confounding and moderating factors available for the analysis include both community-level factors (including school fixed effects, socioeconomic status, level of remoteness, and housing crowdedness) and individual-level factors (including maternal and perinatal health and hospital admissions in early childhood)., Results: The study commenced in 2018, with ethics and data custodian approvals for data access and linkage. This has enabled the completion of data linkage and the commencement of data analysis for individual component studies, with findings expected to be published in 2019 and 2020., Conclusions: This study will provide first evidence of the impact of OM-related HI on the developmental, educational, and social outcomes of Australian Aboriginal children. The findings are expected to have significant implications for policy development, service design, and resource allocation., International Registered Report Identifier (irrid): RR1-10.2196/15464., (©Jiunn-Yih Su, Vincent Yaofeng He, Steven Guthridge, Sven Silburn. Originally published in JMIR Research Protocols (http://www.researchprotocols.org), 15.01.2020.)

Objective: To investigate the association between hearing impairment (HI) and Year 1 school attendance in Aboriginal children in the Northern Territory (NT) of Australia., Methods: Observational cohort study (n=3,744) by analysing linked individual-level information for Aboriginal children from the NT Government school attendance records, NT Perinatal Register and Remote Hearing Assessment dataset, and community level data for relative remoteness, socioeconomic disadvantage and housing crowdedness., Results: Children with unilateral hearing loss, mild HI and moderate or worse HI had significantly lower Year 1 attendance than those with normal hearing, attending 5.6 (95%CI, -9.10 ∼-2.10), 4.0 (95%CI, -7.17 ∼-0.90) and 6.1 (95%CI, -10.71 ∼-1.49) days fewer, respectively. Other variables that yielded significant association were: male gender, having attended preschool less than 20% of available days, speaking English as second language, twin birth and average household size >5., Conclusions: Aboriginal children with any level of HI are likely to have lower school attendance rates in Year 1 than their peers with normal hearing. Implications for public health: In this population, where the prevalence of otitis media and accompanying HI remains extremely high, the early detection and management of hearing loss on entry into primary school should be included in the measures to improve school attendance., (© 2019 The Authors.)