Search

Determination of refractive index of micro-disks of a calcinated ($1100^\circ$C in air) photo-resist SZ2080$^\mathrm{TM}$ was carried out using transmission and reflection spectroscopy. Interference fringes at specific wavenumbers/wavelengths were selected for determination of the optical thickness, hence, the refractive index when the thickness of micro-disks was measured by scanning electron microscopy (SEM). Refractive index of disks of $\sim 6\pm 1~\mu$m thickness were determined at visible and IR (2.5-13~$\mu$m) spectral ranges and where $2.2\pm 0.2$ at visible and IR wavelengths. Peculiarities of optical characterisation of micro-optical structures are discussed in view of possible uncertainties in the definition of geometric parameters, shape and mass density redistribution., Comment: 15 pages, 6 figures, 1 supplementary page. 52 references

Four Stokes parameters (1852) define the polarisation state of light. Measured changes of the Stokes vector of light traversing an inhomogeneous sample are linked to the local anisotropies of absorption and refraction and are harnessed over an increasing range of applications in photonics, material, and space/earth observation. Several independent polarisation sensitive measurements are usually required for determination of the all four Stokes parameters, which makes such characterisation procedure time-consuming or requires complex setups. Here we introduce a single-snapshot approach to Stokes polarimetry in transmission by use of a 4-polarisation camera with the on-chip integrated polarisers. A quarter-waveplate was added in front of the sample and was illuminated by a linearly polarised light. This approach is demonstrated by measuring birefringence $\Delta n\sim 0.012$ of spider silk of only $\sim 6~\mu$m-diameter using microscopy, however, due to its generic nature, it is transferable to other spectral ranges and imaging applications, e.g., imaging from a fast moving satellite or drone or monitoring fast changing events such as phase transitions., Comment: 9 pages, 8 figures

The self-organised conical needles produced by plasma etching of silicon (Si), known as black silicon (b-Si), create a form-birefringent surface texture when etching of Si orientated at angles of $\theta_i < 50 - 70^\circ$ (angle between the Si surface and vertical plasma E-field). The height of the needles in the form-birefringent region following 15~min etching was $d\sim 200$ nm and had a 100 $\mu$m width of the optical retardance/birefringence, characterised using polariscopy. The height of the b-Si needles corresponds closely to the skin-depth of Si $\sim\lambda/4$ for the visible spectral range. Reflection-type polariscope with a voltage-controlled liquid-crystal retarder is proposed to directly measure the retardance $\Delta n\times d/\lambda\approx 0.15$ of the region with tilted b-Si needles. The quantified form birefringence of $\Delta n = - 0.45$ over $\lambda = 400-700$~nm spectral window was obtained. Such high values of $\Delta n$ at visible wavelengths can only be observed in the most birefringence calcite or barium borate as well as in liquid crystals. The replication of b-Si into Ni-shim with high fidelity was also demonstrated and can be used for imprinting of the b-Si nanopattern into other materials., Comment: 14 pages, 13 figures

Background: Nanoscale composition of silk defining its unique properties via a hierarchical structural anisotropy has to be analysed at the highest spatial resolution of tens-of-nanometers corresponding to the size of fibrils made of b-sheets, which are the crystalline building blocks of silk. Results: Nanoscale optical and structural properties of silk have been measured from 100-nm thick longitudinal slices of silk fibers with ~10 nm resolution, the highest so far. Optical sub-wavelength resolution in hyperspectral mapping of absorbance and molecular orientation were carried out for comparison at IR wavelengths 2-10 micrometers using synchrotron radiation. Conclusion: Reliable distinction of transmission changes by only 1-2% due to anisotropy of amide bands was obtained from nano-thin slices of silk.

Domain structure of paracetamol -- popular antipyretic analgesic -- was investigated by infrared (IR) spectroscopy using synchrotron radiation. Absorbance and retardance maps reveal molecular orientation inside the micro-domains of the paracetamol form II which has a better water solubility and compressibility compared to the commercially used forms I. The developed method of analysis representing orientation of optical slow(fast)-axis is compared with azimuthal orientation of the absorbance at several specific IR bands using vector maps. High brightness of synchrotron radiation and hyper-spectral mapping of structural domains in paracetamol clearly reveals the domain boundaries and can potentially be used to observe \emph{in situ} intra-phase transformations of paracetamol forms-I, II, III and melting, which are important for making medical tablets and powders by an industrial process., Comment: eight figures in the main text and one in supplement

A polarised light imaging microscopy with an addition of liquid crystal (LC) phase retarder was implemented to determine the birefringence of silk fibers with the high 2 micrometers spatial resolution. The measurement was carried out with silk fiber (the optical slow axis) and the slow axis of the LC retarder set parallel (a perpendicular alignment can also be used). The direct fit of the transmission data provides a high fidelity determination of birefringence, $Dn = 1.63\times 10^{-2}$ (with 2% uncertainty) of the brown silk fiber (Antheraea pernyi) averaged over the wavelength range $l =$ (425-625) nm. By measuring retardance at four wavelengths it was possible to determine the true value of the birefringence of a thick sample when an optical path may include large number of wavelengths ($2p$ cycles in phase). The numerical procedures and required hardware are described for the do-it-yourself assembly of the imaging polariscope at a fractional budget compared with commercial units., Comment: 7 figures

A thermocouple of Au-Ni with only 2.5-micrometers-wide electrodes on a 30-nm-thick Si3N4 membrane was fabricated by a simple low-resolution electron beam lithography and lift off procedure. The thermocouple is shown to be sensitive to heat generated by laser as well as an electron beam. Nano-thin membrane was used to reach a high spatial resolution of energy deposition and to realise a heat source of sub-1 micrometer diameter. This was achieved due to a limited generation of secondary electrons, which increase a lateral energy deposition. A low thermal capacitance of the fabricated devices is useful for the real time monitoring of small and fast temperature changes, e.g., due to convection, and can be detected through an optical and mechanical barrier of the nano-thin membrane. Temperature changes up to ~2x10^5 K/s can be measured at 10 kHz rate. A simultaneous down-sizing of both, the heat detector and heat source strongly required for creation of thermal microscopy is demonstrated. Peculiarities of Seebeck constant (thermopower) dependence on electron injection into thermocouple are discussed. Modeling of thermal flows on a nano-membrane with presence of a micro-thermocouple was carried out to compare with experimentally measured temporal response., Comment: 5 figures

A water soluble amorphous form of silk was made by ultra-short laser pulse irradiation and detected by nanoscale IR mapping. An optical absorption-induced nanoscale surface expansion was probed to yield the spectral response of silk at IR molecular fingerprinting wavelengths with a high ~20 nm spatial resolution defined by the tip of the probe. Silk microtomed sections of 1-5 micrometers in thickness were prepared for nanoscale spectroscopy and a laser was used to induce amorphisation. Comparison of silk absorbance measurements carried out by table-top and synchrotron Fourier transform IR spectroscopy proved that chemical imaging obtained at high spatial resolution and specificity (able to discriminate between amorphous and crystalline silk) is reliably achieved by nanoscale IR. A nanoscale material characterization using synchrotron IR radiation is discussed., Comment: 3 figures

Three dimensional (3D) fast (< 0.5 hour) printing of micro-optical elements down to sub-wavelength resolution over 100 micrometers footprint areas using femtosecond (fs-)laser oscillator is presented. Using sub-1 nJ pulse energies, optical vortex generators made of polymerised grating segments with an azimuthally changing orientation have been fabricated in SZ2080 resist; width of polymerised rods was ~150 nm and period 0.6-1 micrometers. Detailed phase retardance analysis was carried out manually with Berek compensator (under a white light illumination) and using an equivalent principle by an automated Abrio implementation at 546 nm. Direct experimental measurements of retardance was required since the period of the grating was comparable (or larger) than the wavelength of visible light. By gold sputtering, transmission-type optical vortex generators were turned into reflective ones with augmented retardance, n.h defined by the form birefringence, n, and the height h = 2d where d is the thickness of the polymerised structure. Retardance reached 315 nm as measured with Berek compensator at visible wavelengths. Birefringent phase delays of 180 degrees (or half-wavelength) required for high purity vortex generators can be made based on the proposed approach. Optical vortex generators for telecom wavelengths with sub-wavelength patterns of azimuthally oriented gratings are amenable by direct laser polymerisation., Comment: Pacific Rim Laser Damage 2017: Optical Materials for High Power Lasers (PLD17); Shanghai, China 21 - 24 May 2017. Invited talk

Polarisation analysis of synchrotron THz radiation was carried out with a standard stretched polyethylene polariser and revealed that the linearly polarised (horizontal) component contributes up to 22 +/- 5% to the circular polarised synchrotron emission extracted by a gold-coated mirror with a horizontal slit inserted near a bending magnet edge. Comparison with theoretical predictions shows a qualitative match with dominance of the edge radiation. Grid polarisers 3D-printed out of commercial acrilic resin were tested for the polariser function and showed spectral regions where the dichroic ratio DR > 1 and < 1 implying importance of molecular and/or stress induced anisotropy. Metal-coated 3D-printed THz optical elements can find a range of applications in intensity and polarisation control of THz beams., Comment: 8 figures

Molecular alignment underpins optical, mechanical, and thermal properties of materials, however, its direct measurement from volumes with micrometer dimensions is not accessible, especially, for structurally complex bio-materials. How the molecular alignment is linked to extraordinary properties of silk and its amorphous-crystalline composition has to be accessed by a direct measurement from a single silk fiber. Here, we show orientation mapping of the internal silk fiber structure via polarisation-dependent IR absorbance at high spatial resolution of 4.2 micrometers and 1.9 micrometers in a hyper-spectral IR imaging by attenuated total reflection using synchrotron radiation in the spectral fingerprint region around 6 micrometers wavelength. Free-standing longitudinal micro-slices of silk fibers, thinner than the fiber cross section, were prepared by microtome for the four polarisation method to directly measure the orientational sensitivity of absorbance in the molecular fingerprint spectral window of the amide bands of b-sheets and amorphous polypeptides of silk. Flat lateral micro-slices of silk eliminates shape related artefact in determination of absorbance anisotropy and order parameters of the amide bands., Comment: 13 pages (with supplement), 7 figures and 2 additional figures in the supplement