Search

The enzymes involved in the initial steps of anaerobic benzene catabolism are not known. To try to elucidate this critical step, a metatranscriptomic analysis was conducted to compare the genes transcribed during the metabolism of benzene and benzoate by an anaerobic benzene-degrading, nitrate-reducing enrichment culture. RNA was extracted from the mixed culture and sequenced without prior mRNA enrichment, allowing simultaneous examination of the active community composition and the differential gene expression between the two treatments. Ribosomal and mRNA sequences attributed to a member of the family Peptococcaceae from the order Clostridiales were essentially only detected in the benzene-amended culture samples, implicating this group in the initial catabolism of benzene. Genes similar to each of two subunits of a proposed benzene-carboxylating enzyme were transcribed when the culture was amended with benzene. Anaerobic benzoate degradation genes from strict anaerobes were transcribed only when the culture was amended with benzene. Genes for other benzoate catabolic enzymes and for nitrate respiration were transcribed in both samples, with those attributed to an Azoarcus species being most abundant. These findings indicate that the mineralization of benzene starts with its activation by a strict anaerobe belonging to the Peptococcaceae , involving a carboxylation step to form benzoate. These data confirm the previously hypothesized syntrophic association between a benzene-degrading Peptococcaceae strain and a benzoate-degrading denitrifying Azoarcus strain for the complete catabolism of benzene with nitrate as the terminal electron acceptor.

The surface activity of bovine lipid extracted surfactant (BLES) preparations used in surfactant replacement therapy is studied in dynamic film compression/expansion cycles as a function of relative humidity, surfactant concentration, compression rate, and compression periodicity. BLES droplets were formed in a constrained sessile droplet configuration (CSD). Images obtained during cycling were analyzed using axisymmetric drop shape analysis (ADSA) to yield surface tension, surface area, and drop volume data. The experiments were conducted in a chamber that allowed both humid (100% RH), and "dry" air (i.e. less than 20% RH) environments. It was observed that in humid environments BLES films are not stable and tend to have poor surface activity compared to BLES films exposed to dry air. Further analysis of the data reveal that if BLES films are compressed fast enough (i.e. at physiological conditions) to avoid film hydration, lower minimum surface tensions are achieved. A film hydration-relaxation mechanism is proposed to explain these observations.

The in vitro adsorption kinetics of lung surfactant at air-water interfaces is affected by both the composition of the surfactant preparations and the conditions under which the assessment is conducted. Relevant experimental conditions are surfactant concentration, temperature, subphase pH, electrolyte concentration, humidity, and gas composition of the atmosphere exposed to the interface. The effect of humidity on the adsorption kinetics of a therapeutic lung surfactant preparation, bovine lipid extract surfactant (BLES), was studied by measuring the dynamic surface tension (DST). Axisymmetric drop shape analysis (ADSA) was used in conjunction with three different experimental methodologies, i.e., captive bubble (CB), pendant drop (PD), and constrained sessile drop (CSD), to measure the DST. The experimental results obtained from these three methodologies show that for 100% relative humidity (RH) at 37 degrees C the rate of adsorption of BLES at an air-water interface is substantially slower than for low humidity. It is also found that there is a difference in the rate of surface tension decrease measured from the PD and CB/CSD methods. These experimental results agree well with an adsorption model that considers the combined effects of entropic force, electrostatic interaction, and gravity. These findings have implications for the development and evaluation of new formulations for surfactant replacement therapy.

Accurate surface tension of Teflon® AF 1600 was determined using contact angles of liquids with bulky molecules. For one group of liquids, the contact angle data fall quite perfectly on a smooth curve corresponding to γsv = 13.61 mJ/m2, with a mean deviation of only ±0.24 degrees from this curve. Results suggest that these liquids do not interact with the solid in a specific fashion. However, contact angles of a second group of liquids with fairly bulky molecules containing oxygen atoms, nitrogen atoms, or both deviate somewhat from this curve, up to approximately 3 degrees. Specific interactions between solid and liquid molecules and reorientation of liquid molecules in the close vicinity of the solid surface are the most likely causes of the deviations. It is speculated that such processes induce a change in the solid–liquid interfacial tension, causing the contact angle deviations mentioned above. Criteria are established for determination of accurate solid surface tensions.