Search

A new disintegrated channelization approach for the backward pumped nonlinear distributed Raman amplifier is proposed by enacting the differential coupled equations of Raman amplification, in fiber, trailing by the solution of NLSE using the first integral method first time to the best of our knowledge. A nonlinear channel modeling-based simulation is adapted for the approximation of the Raman gain profile. To realize the real-time dynamic system, 16 multiplexed channels of prime C-band are employed in a QPSK/NRZ modulation environment with a 100 Gbps bit rate for optical network reconfiguration. A non-uniform gain is reported while the disparity in BER is observed from 10−12 to 10−8. [ABSTRACT FROM AUTHOR]

In this article, the proposed Distributed Raman Amplifier (DRA) simulator is designed on the MATLAB Simulink platform. 16 channels DWDM in C-band (1544–1559 nm) and 32 channels CWDM system in S-, C- and L band (1460–1625 nm) are executed with data rate of 100 Gb/s. The designed standalone system realizes the various effects that may arise at the receiver output due to reconfiguration of channels in real-time dynamic WDM optical traffic. Gain excursion assessment, and bit error rate (BER) are investigated for 200 km long Fiber cable and 45 km of Raman amplifier in co-pumping, counter pumping and bidirectional pumping propagation. [ABSTRACT FROM AUTHOR]

The impact of power transients stemming from channel reconfiguration on erbium-doped fiber amplifier (EDFA) gain dynamics in wavelength division multiplexing (WDM) optical networks is investigated. The impact of power transients on EDFA gain dynamics leads to error bursts and impact on the network performance. First, we model an EDFA simulator with one-dimensional nonlinear differential equation that describes the time-dependent population density. For the model to show gain flattening multiplexed channels at different wavelengths, new function blocks are used. Next, to simulate the noise performance of EDFA, forward amplified spontaneous emission noise blocks are designed that add noise dynamically at signal wavelength. Finally, EDFA simulator is used as an in-line amplifier for amplitude shift keying-modulated WDM fiber communication link where the gain clamping facility is provided to protect power imbalance at the receiver. Next, we apply the mentioned model in the estimation on the link performance parameters, like signal-to-noise ratio and bit error rate, and variations in these values by channel add/ drop results from variation in incremented signal output of EDFA. The variations are almost equal at different wavelengths in C- or L-band, which is due to flat gain and also the gain clamping facility of the present EDFA simulator. [ABSTRACT FROM AUTHOR]

A real time multichannel dynamic erbium doped fiber amplifier (EDFA) Simulink model with flat gain and gain clamping facility has been developed on a MATLAB platform. We model the EDFA simulator with one-dimensional nonlinear differential equation that describes the time dependent population density. For the model to show gain flattening multiplexed channels at different wavelengths, the MATLAB function block is used. Next, to simulate the noise performance of EDFA. New forward amplified spontaneous emission (ASE) noise blocks are designed that add noise dynamically at signal wavelength. The model has been implemented in the study of performance characteristics of an EDFA in both C-and L-band signal amplification by simulation. Based on the designed ASE generator, noise figure for different signal wavelengths are calculated. For 980 nm pump power, the noise figure almost reaches the practical limit of 3 dB whereas for 1480 nm pump power, a variation of about 1.5 dB and 0.8 dB is observed from the practical limit for the C- and L-bands, respectively. The present model can be implemented successfully as a test bed in the study of EDFA gain dynamics over the entire third optical communication bandwidth (1525 to 1690 nm) in signal amplification. [ABSTRACT FROM AUTHOR]

A novel erbium-doped fiber amplifier simulator designed using the SIMULINK toolbox of MATLAB 7.0 (The MathWorks, Natick, MA, USA) is reported in this article. The present simulator has an ability to incorporate multi-channel amplification simultaneously in both the C- and L-bands. It is realized by defining new FUNCTION block sets and replacing the MATLAB FUNCTION block set reported earlier for multi-channel amplification. Spectral variation of gain for an erbium-doped fiber amplifier simulator is first verified in both the C- and L-bands. Next, the simulator is employed to study gain excursion in a multi-channel dynamic optical network, where the change in the gain excursion by varying the pump power has also been estimated. The present approach to estimate the gain excursion will find applications in quantifying inter-channel cross-talk due to cross-gain saturation among co-propagating multi-channels in a dynamic optical network. [ABSTRACT FROM AUTHOR]