Search

Microscale particle-target interactions and the resulting modifications of the target material play a crucial role in the domains of industrial manufacturing and application process. As know that the processing and manufacturing, failure prevention, and even the spacecraft protection against hypervelocity micrometeorites and orbital microdebris. Based on such an interesting, noteworthy, and profoundly applied research, it quickly followed up and compiled a series of relevant studies for particle-target interactions of high-speed microparticle impact. Here, it discussed the gas-based, laser-based, and electrostatic-based of the high-speed microparticle impacts. Among these, laser-induced particle impacts stand out for their high throughput and the suitability for operation in small facilities or even on standard laboratory optical benches. Various behaviors have been observed with smaller projectiles, relatively high velocities, and extreme strain rates, which involved the description of launching system, dynamic capturing of high-speed videography, triggering and characterization of material response, and resulting material modification. Subsequently, it conducted a summary and future prospect of the focused topics. As expected that the particle-target interactions will become an effective tool for the study of microprocessing, multi-field coupling, material strengthening and modification, it will bridge multidisciplinary to understand the scientific phenomena involved in the impact process, also provides a novel strategy for the development of next-generation of ballistic impact testing., RETRACTED: see https://doi.org/10.1016/j.mtcomm.2024.110188"Post-publication it was discovered that this paper was submitted to the journal by Yunlei Wang without the knowledge or permission of the co-author Alain Reiser. The unauthorized addition of the co-author was a result of actions taken solely by the corresponding author (Yunlei Wang) and is a clear violation of the journal's policies. The editor would like to clarify that Alain Reiser was not at fault in this matter, and his reputation and contributions should not be called into question. Should the authors decide to revise and resubmit the manuscript in accordance with the journal's policies and ethical guidelines, the editor would be happy to consider it for publication at a future date."QC 20240725

In the first decade of high-velocity microparticle impact research, hardly any modification of the original experimental setup has been necessary. However, future avenues for the field require advancements of the experimental method to expand both the impact variables that can be quantitatively assessed and the materials and phenomena that can be studied. This work explores new design concepts for the launch pad (the assembly that launches microparticles upon laser ablation) that can address the root causes of many experimental challenges that may limit the technique in the future. Among the design changes contemplated, the substitution of a stiff glass launch layer for the standard elastomeric polymer layer offers a number of improvements. First, it facilitates a reduction of the gap between launch pad and target from hundreds to tens of micrometers and thus unlocks a reproducibility in targeting a specific impact location better than the diameter of the test particle itself (±1.75 µm for SiO2 particles 7.38 µm in diameter). Second, the inert glass surface enables experiments at higher temperatures than previously possible. Finally—as demonstrated by the launch of thin-film Au disks—a launch pad made of materials standard in microfabrication paves the way to facile microfabrication of advanced impactors., QC 20231106

In the first decade of high-velocity microparticle impact research, hardly any modification of the original experimental setup has been necessary. However, future avenues for the field require advancements of the experimental method to expand both the impact variables that can be quantitatively assessed and the materials and phenomena that can be studied. This work explores new design concepts for the launch pad (the assembly that launches microparticles upon laser ablation) that can address the root causes of many experimental challenges that may limit the technique in the future. Among the design changes contemplated, the substitution of a stiff glass launch layer for the standard elastomeric polymer layer offers a number of improvements. First, it facilitates a reduction of the gap between launch pad and target from hundreds to tens of micrometers and thus unlocks a reproducibility in targeting a specific impact location better than the diameter of the test particle itself (±1.75 µm for SiO2 particles 7.38 µm in diameter). Second, the inert glass surface enables experiments at higher temperatures than previously possible. Finally-as demonstrated by the launch of thin-film Au disks-a launch pad made of materials standard in microfabrication paves the way to facile microfabrication of advanced impactors.

QC 20231106

Electrohydrodynamic redox 3D printing (EHD-RP) is an additive manufacturing (AM) technique with submicron resolution and multi-metal capabilities, offering the possibility to switch chemistry during deposition “on-the-fly”. Despite the potential for synthesizing a large range of metals by electrochemical small-scale AM techniques, to date, only Cu and Ag have been reproducibly deposited by EHD-RP. Here, we extend the materials palette available to EHD-RP by using aqueous solvents instead of organic solvents, as used previously. We demonstrate deposition of Cu and Zn from sacrificial anodes immersed in acidic aqueous solvents. Mass spectrometry indicates that the choice of the solvent is important to the deposition of pure Zn. Additionally, we show that the deposited Zn structures, 250 nm in width, can be partially converted into semiconducting ZnO structures by oxidation at 325 °C in air., QC 20231106

QC 20231106

The control of materials’ microstructure is both a necessity and an opportunity for micro/nanometer-scale additive manufacturing technologies. On the one hand, optimization of purity and defect density of printed metals is a prerequisite for their application in microfabrication. On the other hand, the additive approach to materials deposition with highest spatial resolution offers unique opportunities for the fabrication of materials with complex, 3D graded composition or microstructure. As a first step toward both—optimization of properties and site-specific tuning of microstructure—an overview of the wide range of microstructure accessed in pure copper (up to >99.9 at.%) by electrohydrodynamic redox 3D printing is presented, and on-the-fly modulation of grain size in copper with smallest segments ≈400 nm in length is shown. Control of microstructure and materials properties by in situ adjustment of the printing voltage is demonstrated by variation of grain size by one order of magnitude and corresponding compression strength by a factor of two. Based on transmission electron microscopy and atom probe tomography, it is suggested that the small grain size is a direct consequence of intermittent solvent drying at the growth interface at low printing voltages, while larger grains are enabled by the permanent presence of solvent at higher potentials., QC 20231106

Currently, the focus of additive manufacturing (AM) is shifting from simple prototyping to actual production. One driving factor of this process is the ability of AM to build geometries that are not accessible by subtractive fabrication techniques. While these techniques often call for a geometry that is easiest to manufacture, AM enables the geometry required for best performance to be built by freeing the design process from restrictions imposed by traditional machining. At the micrometer scale, the design limitations of standard fabrication techniques are even more severe. Microscale AM thus holds great potential, as confirmed by the rapid success of commercial micro-stereolithography tools as an enabling technology for a broad range of scientific applications. For metals, however, there is still no established AM solution at small scales. To tackle the limited resolution of standard metal AM methods (a few tens of micrometers at best), various new techniques aimed at the micrometer scale and below are presently under development. Here, we review these recent efforts. Specifically, we feature the techniques of direct ink writing, electrohydrodynamic printing, laser-assisted electrophoretic deposition, laser-induced forward transfer, local electroplating methods, laser-induced photoreduction and focused electron or ion beam induced deposition. Although these methods have proven to facilitate the AM of metals with feature sizes in the range of 0.1–10 µm, they are still in a prototype stage and their potential is not fully explored yet. For instance, comprehensive studies of material availability and material properties are often lacking, yet compulsory for actual applications. We address these items while critically discussing and comparing the potential of current microscale metal AM techniques., QC 20231106

A novel 3D printing method for voxel-by-voxel metal printing is presented. Hollow atomic force microscopy (AFM) cantilevers are used to locally supply metal ions in an electrochemical cell, enabling a localized electroplating reaction. By exploiting the deflection feedback of these probes, electrochemical 3D metal printing is, for the first time, demonstrated in a layer-by-layer fashion, enabling the fabrication of arbitrary-shaped geometries., QC 20231106

The ultimate aim of this study is to construct polymer nanocomposite patterns by dip-pen nanolithography (DPN). Recent investigations have revealed the effect of the amount of ink (Laplace pressure) on the mechanism of liquid ink writing. In this study it is shown that not only the amount of ink, but also physisorption and surface diffusion are relevant. After a few writing steps, physisorption and surface diffusion outweigh the influence of the amount of ink, allowing consistent patterning governed by dwell times and writing speeds. Polymer matrices can be utilized as a delivery medium to deposit functional particles. DPN patterning of polymer nanocomposites allows for local tuning of the functionality and mechanical strength of the written patterns in high resolution, with the benefit of pattern flexibility. Typically polymer matrices with volatile components are used as a delivery medium for nanoparticle deposition, with subsequent removal of loosely bound matrix material by heating or oxygen plasma. In our study, nanocomposite patterns were constructed, and the differences between polymer and nanocomposite patterning were investigated. Cross-sectional SEM and TEM analysis confirmed that nanoparticles can be deposited with the liquid-polymer ink and are evenly distributed in the polymer matrix., QC 20231106

Heterogeneous composite materials with variable local stiffness are widespread in nature, but are far less explored in engineering structural applications. The development of heterogeneous synthetic composites with locally tuned elastic properties would allow us to extend the lifetime of functional devices with mechanically incompatible interfaces, and to create new enabling materials for applications ranging from flexible electronics to regenerative medicine. Here we show that heterogeneous composites with local elastic moduli tunable over five orders of magnitude can be prepared through the site-specific reinforcement of an entangled elastomeric matrix at progressively larger length scales. Using such a hierarchical reinforcement approach, we designed and produced composites exhibiting regions with extreme soft-to-hard transitions, while still being reversibly stretchable up to 350%. The implementation of the proposed methodology in a mechanically challenging application is illustrated here with the development of locally stiff and globally stretchable substrates for flexible electronics., QC 20231106