Search

Abstract Introduction This study was performed to examine craniofacial structures in persons with hypodontia and to reveal any differences, that may occur, when agenetic teeth are only found in the maxilla, the mandible or in both jaws. The groups consistent of 50 children (33 girls, 17 boys) aged between 9 and 13.5 years were analyzed and assigned to three subgroups. Group 1 = upper jaw hypodontia. Group 2 = lower jaw hypodontia. Group 3 = hypodontia in both jaws. Materials and methods Eleven angular and three index measurements from lateral encephalographs and two linear measurements from dental blaster casts were calculated. All data was statistically analyzed, parameters with p < 5% were investigated for each subgroup respectively. Results In comparison with standards the study group showed bimaxillary retrognathism and a reduction of the lower anterior facial height. Moreover both overbite and overjet significantly increased. Other values laid within the normal ranges. Evaluating results of the subgroups, differences in the means of SNA, SNB and overjet between the groups were observed. Analysis of the mandibular growth pattern revealed, that neither vertical nor horizontal patterns are dominant in hypodontia patients. Conclusions In certain dentofacial parameters differences between persons with hypodontia and such with full dentition exist. According to our findings agenetic teeth may have a negative influence on the saggital development of a jaw and the lower face and may be responsible for increased overbites. This should receive attention in orthodontic treatment of hypodontia patients.

Objectives: Nicotine is considered an etiologic factor for chronic inflammatory phenomena within the periodontal ligament that may result in loss of periodontal attachment. Considering that smokers account for 26% of adult and 12% of adolescent patients in orthodontic practice, we performed in vivo and in vitro studies as to whether orthodontic forces may add to the nicotine-induced loss of periodontal bone., Methods: Fourteen male rats (Fischer 344 inbred) were used. Seven of these served as controls, while the other seven received daily subcutaneous injections of 1.89 mg L-nicotine per kg body weight. Both groups were exposed to orthodontic mesialization of the first two upper left molars using a NiTi closed-coil spring, the contralateral side serving as control. Periodontal bone loss was assessed by cone-beam computed tomography (CBCT). Human periodontal fibroblasts were stressed by compression (2 g/cm(2)) and/or nicotine (3/5/7.5 µmol), and the expression of cyclooxygenase-2 (COX-2), prostaglandin E2 (PGE2), interleukin-6 (IL-6), osteoprotegerin (OPG), and receptor activator of nuclear factor κB ligand (RANKL) was determined at the transcriptional level by quantitative real-time polymerase chain reaction (qRT-PCR) and at the translational level by enzyme-linked immunosorbent assay (ELISA). In addition, differentiation of co-cultured murine RAW264.7 cells to osteoclast-like cells was quantified by tartrate-resistant acid phosphatase (TRAP) staining., Results: Orthodontic force application in vivo led to a significant increase in nicotine-induced periodontal bone loss, and cell compression in vitro to increased COX-2, PGE2, IL-6, and RANKL expression, reduced OPG expression, and enhanced differentiation of RAW264.7 cells to osteoclast-like cells compared to nicotine alone., Conclusion: Additional loss of periodontal bone must be expected during orthodontic treatment of smokers. Clinicians should inform their patients of this increased risk and refrain from performing tooth movements before cessation of smoking.

Orthodontic miniscrews are exposed to three mechanical loading phases during clinical use: torsional loading upon insertion, flexural loading during anchorage function, and torsional loading upon removal. The aim of this study was to simulate clinical loading conditions for different types of orthodontic miniscrews in vitro to quantify the effects of combined torsional and bending stress. Various orthodontic miniscrew systems (Lomas, Dual-top, Aarhus anchorage, Tomas-pin and T.I.T.A.N.-pin) comprising 10 samples each were subjected to the following loading sequences in vitro: a torsional load corresponding to manual insertion with limited torque; and flexural loading at two different insertion depths. For all screw systems with torsional pre-loading (simulating insertion), subsequent flexural loading (simulating anchorage) yielded permanent deformations of approximately 0.15-0.25 mm, depending on the insertion depth. Since EDX analysis revealed comparable elemental compositions for the different screw systems, the differences in mechanical properties are attributed to screw design. Torsional loading during screw insertion may cause premature mechanical weakening and needs to be minimized. Unless fully inserted, screws show pronounced plastic deformation and hence fracture risk under subsequent flexural loading.

Human teeth with substantial coronal defects are subject to reconstruction by means of post and core restorations. Typically, such a restoration comprises a slightly cylindrical post onto which an abutment of varying shape, depending on the designated restoration, is attached. As clinical results are not satisfactory to date, we proposed a new proprietary post and core design which makes use of positive locking. As this prefabricated system is not customised to an individual root's cross-sectional geometry (usually oval), a varying amount of radicular dentin is left in periphery of the core's outer edge. The aim of this study was to assess the implications of this fact, i.e., whether the root has to endure higher overall stress levels which ultimately may lead to failure of one of the components involved. A series of finite element simulations were performed to evaluate stress and strain on the system, in which the proposed post and core was embedded into a virtual dentin cylinder of different diameters, ranging from flush mounting of the restoration to a dentin excess of 4 mm, and subsequently loaded with forces with two angles of attack (90 degrees and 130 degrees ). The results show that flush mounting yields an agreeable stress and strain distribution within the radicular dentin, but overall stress levels drop significantly with an excess of 0.5 mm of surrounding dentin. More than 1 mm excess was not found to have profound positive effects.

To assess the usefulness of different post and core materials and systems, in vitro testing of fracture strength and fatigue resistance is a useful tool. However, the literature does not present coherent results as to which system can withstand the highest loads. With a geometrical model, the effects of load angulation and contact point location on the generated forces were calculated. To validate the mathematical model, a set of measurements was performed with a set-up that made it possible to measure the critical forces on a post and core restoration. A high level of correlation between the predictions of the model and the measurements was found. It was shown that the resulting forces are strongly dependent on the precise design of the test set-up and results from different geometries cannot be compared directly. Very strong sensitivity to small misalignment was found, all of which serves to explain the large differences in the literature.