Search

(1) Background: Cleft lip and palate is the most common congenital malformation of the head and neck. After surgical closure, velopharyngeal dysfunction can arise, which has implications for phonation, sucking, swallowing, middle ear function, and interpersonal well-being. This case series aimed to present an adaptation of the conventional pharyngeal obturator design in order to allow its use with fixed orthodontic appliances. (2) Methods: A new custom-made pharyngeal obturator device was built in order to enable a correct function of the velopharyngeal valve. The fabrication of the plate was made by altering the conventional Hawley retainer, replacing the Adams hooks with 0.9 mm spherical hooks and removing the buccal arch. (3) Results: The new pharyngeal obturator design was used in six cleft patients with fixed orthodontic appliances. The appliance was well tolerated and there was a slight improvement in auditory-perceptive evaluations. (4) Conclusions: The new pharyngeal bulb design proved to have good retention during fixed orthodontic treatment. Moreover, despite the short-term follow-up, it also showed a reduction in the severity of the hypernasality sentences.

Miniscrews are devices that allow for absolute skeletal anchorage. However, their use has a higher failure rate (10–30%) than dental implants (10%). To overcome these flaws, chemical and/or mechanical treatment of the surface of miniscrews has been suggested. There is no consensus in the current literature about which of these methods is the gold standard; thus, our objective was to carry out a systematic review and meta-analysis of the literature on surface treatments of miniscrews. The review protocol was registered (PROSPERO CRD42023408011) and is in accordance with the PRISMA guidelines. A bibliographic search was carried out on PubMed via MEDLINE, Cochrane Library, Embase and Web of Science. The initial search of the databases yielded 1684 results, with 98 studies included in the review, with one article originating from the search in the bibliographic references of the included studies. The results of this systematic review show that the protocols of miniscrew surface treatments, such as acid-etching; sandblasting, large-grit and acid-etching; photofunctionalization with ultraviolet light; and photobiomodulation, can increase stability and the success of orthodontic treatment. The meta-analysis revealed that the treatment with the highest removal torque is SLA, followed by acid-etching. On the other hand, techniques such as oxidative anodization, anodization with pre-calcification and heat treatment, as well as deposition of chemical compounds, require further investigation to confirm their effectiveness.

Objetivos: A osteotomia de Le Fort I pode induzir alterações estruturais ou anatómicas nas vias aéreas superiores, particularmente ao nível dos seios maxilares. O objetivo deste estudo foi comparar o volume dos seios maxilares antes e após a osteotomia de Le Fort I de avanço. Metódos: Neste estudo retrospetivo foram incluídos 19 doentes submetidos a tratamento ortodôntico-cirúrgico com osteotomia de Le Fort I de avanço. As tomografias computorizadas de feixe cónico, pré-operatória (T0) e pós-operatória (T1), foram analisadas com recurso ao software ITK-SNAP a fim de avaliar o volume dos seios maxilares. O teste t de Student para amostras emparelhadas foi utilizado para avaliar o efeito da osteotomia de Le Fort I de avanço no volume dos seios maxilares. Considerou-se um nível de significância de p

Long-term stability is a crucial point in order to keep the patient’s aesthetic and functional balance. The aim of this study was to evaluate dental and skeletal relapse in patients who underwent orthodontic-surgical treatment. This retrospective study included 25 patients who corrected their dentofacial deformity through orthodontics and orthognathic surgery. The dental casts and lateral cephalograms were evaluated prior to orthodontic treatment (T0), final of orthodontic-surgical treatment (T1) and long-term retention phase (T2). The Wilcoxon test with p-value corrected by the Benjamini–Hochberg method was used to assess differences between the groups. The influence of retention duration was assessed using the Kruskal–Wallis method. The association of nominal variables and differences between quantitative variables were assessed using the Fisher and Mann–Whitney tests, respectively. No dental or skeletal variable presented statistically significant differences between the final orthodontic-surgical treatment and the long-term retention phase. Eight patients presented dental relapse (32–95% CI [12.4%; 51.7%]), but no skeletal relapse was observed in any of the 25 individuals. The type of malocclusion did not influence the relapse rate of orthodontic-surgical treatment (Fisher, p = 0.202). No differences were found between the different retention times, sex and age at the end of treatment. Orthodontic-surgical treatment showed long-term stability in the present study group.

Dual-energy X-ray absorptiometry is used to determine bone density in several pathologies, namely osteoporosis and fracture risk in post-menopausal women. The aim of this study was to identify, appraise and synthesize all available evidence about the correlation between Dual Energy X-ray Absorptiometry (DEXA) and Cone Beam Computed Tomography (CBCT) techniques through a systematic review. A systematic literature search was conducted in the following databases: PubMed via MEDLINE, Cochrane Library, EMBASE and Web of Science Core Collection, along with several sources of grey literature. The Cochrane Risk of Bias Tools were used to perform the qualitative assessment of the selected studies. A total of 913 articles were initially scrutinized and 11 were included for qualitative analysis, of which 3 were included in a meta-analysis. Most of the included studies revealed a low risk of bias (7 out of 11). A strong correlation (min r = 0.46 max r = 0.62) between DEXA and CBCT values were found. Thus, opportunistic CBCT scans may be used to assess the bone mineral density and fracture risk, improving the ability to track disease progression and providing better care.

Aim: Cleft lip and palate (CLP) patients have a greater predisposition to tooth malformation, which could affect pulp volume. The aim of this study is to evaluate the dental pulp volume of central incisors in 3D images between individuals with and without CLP. Materials and Methods: This retrospective case-control study is single-centered and was recruited between January 2016 and October 2022. Ninety-four patients who were followed in the Institute of Orthodontics were evaluated and divided into two groups: a control group of patients without CLP and a test group of patients with CLP. The 3D data were imported by 3D image semi-automatic segmenting software named ITK-SNAP to calculate tooth pulp volume. Results: The dental pulp volume for both groups, control and CLP, did not show statistically significant differences. In the cleft group, when comparing the pulp volume between the cleft side and the non-cleft side, the cleft side showed a smaller volume. Regarding age and sex, no statistically significant differences were observed. Conclusions: Although there are no differences in mean pulp volume between patients with and without CLP, there is a pulp volume reduction in the teeth on the cleft side when compared to the unaffected contralateral side.

Craniofacial bone defects are one of the biggest clinical challenges in regenerative medicine, with secondary autologous bone grafting being the gold-standard technique. The development of new three-dimensional matrices intends to overcome the disadvantages of the gold-standard method. The aim of this paper is to put forth an in-depth review regarding the clinical efficiency of available 3D printed biomaterials for the correction of alveolar bone defects. A survey was carried out using the following databases: PubMed via Medline, Cochrane Library, Scopus, Web of Science, EMBASE, and gray literature. The inclusion criteria applied were the following: in vitro, in vivo, ex vivo, and clinical studies; and studies that assessed bone regeneration resorting to 3D printed biomaterials. The risk of bias of the in vitro and in vivo studies was performed using the guidelines for the reporting of pre-clinical studies on dental materials by Faggion Jr and the SYRCLE risk of bias tool, respectively. In total, 92 publications were included in the final sample. The most reported three-dimensional biomaterials were the PCL matrix, β-TCP matrix, and hydroxyapatite matrix. These biomaterials can be combined with different polymers and bioactive molecules such as rBMP-2. Most of the included studies had a high risk of bias. Despite the advances in the research on new three-dimensionally printed biomaterials in bone regeneration, the existing results are not sufficient to justify the application of these biomaterials in routine clinical practice.

Orthognathic surgery is a procedure used to correct intermaxillary discrepancies, thus promoting significant improvements in chewing and breathing. During the surgical planning stage, orthodontists often use two-dimensional imaging techniques. The assessment is based on CBCT images and dental cast models to overcome these limitations; however, the evaluation of soft tissues remains complex. The aim of the present study was to develop a co-registration method of CBCT and photo images that would result in realistic facial image reconstruction. CBCT images were three-dimensionally rendered, and the soft tissues were subsequently segmented resulting in the cranial external surface. A co-registration between the obtained surface and a frontal photo of the subject was then carried out. From this mapping, a photorealistic model capable of replicating the features of the face was generated. To assess the quality of this procedure, seven orthodontists were asked to fill in a survey on the models obtained. The survey results showed that orthodontists consider the three-dimensional model obtained to be realistic and of high quality. This process can automatically obtain a three-dimensional model from CBCT images, which in turn may enhance the predictability of surgical-orthognathic planning.

Oronasal fistula can persist after conventional secondary alveolar bone graft surgery, which may lead to functional issues, such as regurgitation of fluids from the oral to the nasal cavity. This manuscript describes a clinical case of a patient with a bilateral cleft lip and palate that underwent tongue graft surgery for closure of an oronasal fistula after three failed local mucosa flap surgeries. The multidisciplinary treatment was comprised of orthodontic treatment, mucosa and alveolar grafts for palate closure and aesthetic rehabilitation of the anterior maxillary teeth. Smile aesthetics were noticeably improved, enhancing the patient’s self-perception and confidence.

Velopharyngeal insufficiency may occur as a result of an anatomical or structural defect and may be present in patients with cleft lip and palate. The treatment options presented in the literature are varied, covering invasive and non-invasive methods. However, although these approaches have been employed and their outcomes reviewed, no conclusions have been made about which approach is the gold-standard. This umbrella review aimed to synthesize the current literature regarding velopharyngeal insufficiency treatments in cleft lip and palate patients, evaluating their effectiveness based on systematic reviews. A standardized search was carried out in several electronic databases, namely PubMed via Medline, Web of Science, Cochrane Library, and Embase. The quality of the included studies was evaluated using AMSTAR2 and degree of overlap was analyzed using Corrected Covered Area. Thirteen articles were included in the qualitative review, with only 1 in the non-invasive method category, and 12 in the invasive method category. All reviewed articles were judged to be of low quality. In symptomatic patients, treatment did not solely comprise speech therapy, as surgical intervention was often necessary. Although there was no surgical technique considered to be the gold standard for the correction of velopharyngeal insufficiency, the Furlow Z-plasty technique and minimal incision palatopharyngoplasty were the best among reported techniques.

Three-dimensional technologies are one of the most recent and relevant advancements in the field of Dentistry. These systems, including intraoral scans, 3D imaging exams (CAT scan, CBCT and MRI), CAD/CAM 3D printing devices and 3D computer software, have enabled clinicians to greatly improve patient care along with reducing treatment planning time. The present descriptive study aims to explore possible applications of 3D technologies during the diagnosis, treatment plan, case monitoring and result assessment in orthodontics. The overall upgrade provided by these technologies can improve the clinicians’ workflow and effectiveness by simplifying conventional techniques considered to be especially arduous.

Background: There has been an increase in demand for orthodontic treatment within the adult population, who likely receive restorative treatments using ceramic structures. The current state of the art regarding the most effective method to achieve an appropriate bond strength of brackets on ceramic surfaces isn’t consensual. This systematic review aims to compare the available surface treatments to ceramics and determine the one that allows to obtain the best bond strength. Methods: This systematic review followed the PRISMA guidelines and the PICO methodology was used, with the question “What is the most effective technique for bonding brackets on ceramic crowns or veneers?”. The research was carried out in PubMed, Web of Science, Embase and Cochrane Library databases. In vitro and ex vivo studies were included. The methodological quality was evaluated using the guidelines for reporting of preclinical studies on dental materials by Faggion Jr. Results: A total of 655 articles searched in various databases were initially scrutinized. Sevety one articles were chosen for quality analysis. The risk of bias was considered medium to high in most studies. The use of hydrofluoric acid (HF), silane and laser afforded the overall best results. HF and HF plus laser achieved significantly highest bond strength scores in felsdphatic porcelain, while laser was the best treatment in lithium disilicate ceramics. Conclusions: The most effective technique for bonding brackets on ceramic is dependent on the type of ceramic.

Three-dimensional (3D) resin medical-dental devices have been increasingly used in recent years after the emergence of digital technologies. In Orthodontics, therapies with aligners have gained popularity, mainly due to the aggressive promotion policies developed by the industry. However, their systemic effects are largely unknown, with few studies evaluating the systemic toxicity of these materials. The release of bisphenol A and other residual monomers have cytotoxic, genotoxic, and estrogenic effects. This systematic review aims to analyze the release of toxic substances from 3D resins used in Orthodontics and their toxic systemic effects systematically. The PICO question asked was, “Does the use of 3D resins in orthodontic devices induce cytotoxic effects or changes in estrogen levels?”. The search was carried out in several databases and according to PRISMA guidelines. In vitro, in vivo, and clinical studies were included. The in vitro studies’ risk of bias was assessed using the guidelines for the reporting of pre-clinical studies on dental materials by Faggion Jr. For the in vivo studies, the SYRCLE risk of bias tool was used, and for the clinical studies, the Cochrane tool. A total of 400 articles retrieved from the databases were initially scrutinized. Fourteen articles were included for qualitative analysis. The risk of bias was considered medium to high. Cytotoxic effects or estrogen levels cannot be confirmed based on the limited preliminary evidence given by in vitro studies. Evidence of the release of bisphenol A and other monomers from 3D resin devices, either in vitro or clinical studies, remains ambiguous. The few robust results in the current literature demonstrate the absolute need for further studies, especially given the possible implications for the young patient’s fertility, which constitutes one of the largest groups of patients using these orthodontic devices.

(1) Background: Mandibular deficiency is one of the most common growth disorders of the facial skeleton. Recently, distraction osteogenesis has been suggested as the treatment of choice for overcoming the limitations of conventional orthognathic surgery; (2) Methods: A new custom-manufactured dental-anchored distractor was built and anchored in the first molar and lower canine. It consists of a stainless-steel disjunction screw, adapted and welded to the orthodontic bands through two 1.2 mm diameter connector bars with a universal silver-based and cadmium-free solder; (3) Results: The distractor described can be a useful tool to correct mandibular retrognathia and is better tolerated by patients, especially in severe cases; (4) Conclusions: The dental-anchored distractor increases the anterior mandibular bone segment without affecting the gonial angle or transverse angulation of the segments and avoids posterior mandibular rotation, overcoming the limitations of conventional surgical treatment.

ABSTRACT. Soibelman D.C., Costa G.C.S., Sturzenecker M.R.T. & Fernandes J.I. [Gastroenteritis in dog associated with Cryptosporidium sp: endoscopic and histopathologic changes - Case report.] Gastroenterite associada a Cryptosporidium sp. em cão: alterações endoscópicas e histopatológicas - Relato de caso. Revista Brasileira de Medicina Veterinária, 37(supl.1):77-80, 2015. Programa de Pós-Graduação em Saúde Animal no Amazônas, Universidade Federal do Pará, Campus II, BR 316 Km 62, Castanhal, PA 68743-970, Brasil. E-mail: deboracostabile75@gmail.com A male canine, no breed, with three years old was examined complaining of intermittent vomiting and sporadic diarrhea. During the endoscopic examination the gastric mucosa was very swollen and hyperemic and inflammation in pylorus with bilious reflux. During the procedure, the duodenal mucosa was grossly swollen and hyperemic; suggesting enanthematous pangastritis and duodenitis. The histopathological evaluation revealed chronic superficial gastritis fundic discrete foveolar hyperplasia; pyloric mucosa with superficial epithelial bodies with Cryptosporidium sp; surface fragments of intestinal villi with rare forms compatible with Cryptosporidium sp.