Search

The designers of radial turbomachinery need detailed information on the impact of the side chamber flow on axial thrust and torque. A previous paper investigated centripetal flow through narrow rotor–stator cavities and compared axial thrust, rotor torque and radial pressure distribution to the case without through-flow. Consequently, this paper extends the investigated range to centrifugal through-flow as it may occur in the hub side chamber of radial turbomachinery. The chosen operating conditions are representative of high-pressure centrifugal compressors used in, for example, carbon capture and storage applications as well as hydrogen compression. To date, only the Reynolds number range up to Re=2·107 has been investigated for centrifugal through-flow. This paper extends the range to Reynolds numbers of Re=2·108 and reports results of experimental and numerical investigations. It focuses on the radial pressure distribution in the rotor–stator cavity and shows the influence of the Reynolds number, cavity width and centrifugal mass flow rate. It therefore extends the range of available valid data that can be used to design radial turbomachinery. Additionally, this analysis compares the results to data and models from scientific literature, showing that in the higher Reynolds number range, a new correlation is required. Finally, the analysis of velocity profiles and wall shear delineates the switch from purely radial outflow in the cavity to outflow on the rotor and inflow on the stator at high Reynolds numbers in comparison to the results reported by others for Reynolds numbers up to Re=2·107.

In the side-chambers of radial turbomachinery, which are rotor–stator cavities, complex flow patterns develop that contribute substantially to axial thrust on the shaft and frictional torque on the rotor. Moreover, leakage flow through the side-chambers may occur in both centripetal and centrifugal directions which significantly influences rotor–stator cavity flow and has to be carefully taken into account in the design process: precise correlations quantifying the effects of rotor–stator cavity flow are needed to design reliable, highly efficient turbomachines. This paper presents an experimental investigation of centripetal leakage flow with and without pre-swirl in rotor–stator cavities through combining the experimental results of two test rigs: a hydraulic test rig covering the Reynolds number range of 4 × 10 5 ≤ R e ≤ 3 × 10 6 and a test rig for gaseous rotor–stator cavity flow operating at 2 × 10 7 ≤ R e ≤ 2 × 10 8 . This covers the operating ranges of hydraulic and thermal turbomachinery. In rotor–stator cavities, the Reynolds number R e is defined as R e = Ω b 2 ν with angular rotor velocity Ω , rotor outer radius b and kinematic viscosity ν . The influence of circumferential Reynolds number, axial gap width and centripetal through-flow on the radial pressure distribution, axial thrust and frictional torque is presented, with the through-flow being characterised by its mass flow rate and swirl angle at the inlet. The results present a comprehensive insight into the flow in rotor–stator cavities with superposed centripetal through-flow and provide an extended database to aid the turbomachinery design process.

The behaviour of Cu and Cr HiPIMS (high power impulse magnetron sputtering) discharges was investigated by a combination of optical emission spectroscopy, energy-resolved mass spectrometry and optical imaging, for the complete current–voltage characteristic range achievable within our experimental conditions. Inflection points typical of HiPIMS current–voltage characteristics separate plasma regimes perfectly differentiated in terms of flux composition of species towards the substrate, deposition rate, and the nature of plasma self-organization. The reorganization of the HiPIMS plasma into spokes (areas of high ionization over the target) is associated to one regime of high plasma conductivity, where also deposition rate is limited. This spoke-dominated regime can be substituted by a homogeneous regime at higher powers, where there is an increase of deposition rate, which is driven mostly by an increase in the flux of metal neutrals and metal double-charged ions. The relevance of secondary electron emission mechanisms for the support of the spoke-dominated regime in reactive and non-reactive sputtering conditions is discussed. [ABSTRACT FROM AUTHOR]