Search

Aptamers are short single-stranded oligonucleotides (either DNA or RNA) that can fold into well-defined three-dimensional (3D) spatial structures which enable them to capture their specific target by complementary shape interactions. Aptamers are selected from large random libraries through the SELEX process and only a small fraction of the sequence is involved in direct docking with the target. In this paper, we describe the possible truncation variants of zearalenone (ZEA) aptamer which might be an effective binding region for the target. The originally selected zearalenone (ZEA) aptamer was 80-mer in length and shown to bind the target with a high affinity (Kd = 41 ± 5 nM). Herein, computational docking simulation was performed with 15 truncated variants to determine the predicted binding energy and responsible binding site of the aptamer-analyte complex. The results revealed that 5 truncated variants had binding energy lower than − 7.0 kcal/mol. Circular dichroism analysis was performed on the shortlisted aptamer and the conformational change of aptamers was observed with the presence of an analyte. Aptamer Z3IN (29-mer) was chosen as the most enhanced affinity for its target with a dissociation constant of 11.77 ± 1.44 nM. The aptamer was further applied in the electrochemical aptasensor of ZEA based on an indirect competitive format. The results demonstrated that the truncated aptamer leads to an enhancement of the sensitivity of the biosensor.

Snakebite is a neglected tropical disease that causes considerable death and disability in the tropical world. Although snakebite can cause a variety of pathologies in victims, haemotoxic effects are particularly common and are typically characterised by haemorrhage and/or venom-induced consumption coagulopathy. Antivenoms are the mainstay therapy for treating the toxic effects of snakebite, but despite saving thousands of lives annually, these therapies are associated with limited cross-snake species efficacy due to venom variation, which ultimately restricts their therapeutic utility to particular geographical regions. In this study, we sought to explore the potential of ssDNA aptamers as toxin-specific inhibitory alternatives to antibodies. As a proof of principle model, we selected snake venom serine protease toxins, which are responsible for contributing to venom-induced coagulopathy following snakebite envenoming, as our target. Using SELEX technology, we selected ssDNA aptamers against recombinantly expressed versions of the fibrinogenolytic SVSPs Ancrod from the venom of Calloselasma rhodostoma and Batroxobin from Bothrops atrox. From the resulting pool of specific ssDNA aptamers directed against each target, we identified candidates that exhibited low nanomolar binding affinities to their targets. Downstream ALISA, fibrinogenolysis, and coagulation profiling experiments demonstrated that the candidate aptamers were able to recognise native and recombinant SVSP toxins and inhibit toxin- and venom-induced prolongation of plasma clotting times and consumption of fibrinogen, with inhibitory potencies highly comparable to commercial polyvalent antivenoms. Our findings demonstrate that rationally selected toxin-specific aptamers can exhibit broad in vitro cross-reactivity against toxins found in different snake venoms and are capable of inhibiting toxins in pathologically relevant in vitro and ex vivo models of venom activity. These data highlight the potential utility of ssDNA aptamers as novel toxin-inhibiting therapeutics of value for tackling snakebite envenoming.

Colorectal cancer (CC) is one of the common causes of cancer-related deaths around the globe. Identification of a novel biomarker for CC is of paramount importance for early diagnostics and reducing its mortality. Among the most promising biomarker candidates, exosomes hold great potential for cancer diagnosis, management, and treatment. Exosomes are extracellular vesicles secreted from cells and they contribute to the intercellular communication, immune response and the pathogenesis of many diseases including cardiovascular diseases, neurodegenerative diseases, and cancer. Several methods have been developed/utilized for exosome isolation and purification. However, these methods are time-consuming and have low purification efficiency. In this work, we developed the "apta-magnetic biosensor" platform for isolation, purification and detection of exosomes from cell culture. Anti-CD63 aptamer, which is conjugated to the surface of magnetic nanobeads, was used as a recognition element. A dynamic separation system was used which employs a transverse magnetic field along a microfluidic channel. The channel was exposed to an alternate magnetic field which imposes alternate magnetic force onto the magnetic bead-exosome complex. The combination of the fluid flow and magnetic force generates several "alternate trapping and releasing" events under continuous-flow conditions with each event representing a washing cycle. The graphene coated onto the surface of the magnetic nanobeads was used as a quencher for the fluorescently labeled aptamer (OFF state) in the absence of the target. Upon the addition of CD63 target protein, the aptamer dissociates from the graphene and binds to the target hence increasing the fluorescence intensity (ON state). A calibration plot of variable concentrations of exosomes vs fluorescence intensity was obtained and the detection limit was calculated as 1457 particles/mL. The specificity of the sensor was tested using closely associated proteins. The results showed that the aptamagnetic isolation, pre-concentration of exosomes and quantification demonstrate great potential for various clinical applications.

Cylindrospermopsin (CYN) is one of the most concerning cyanotoxins due to its potential toxicity and spreading to various environments including drinking water. CYN has potential interferences with human and animal metabolic pathways, which influence the functions of organs including liver, kidneys, lungs, etc. CYN is involved in the inhibition of protein synthesis and detachment of ribosomes from the endoplasmic reticulum membrane. It also interacts with soluble proteins, which are associated with protein translations. It is believed that cytochrome 450 is responsible for the rapid toxicity of CYN. Researchers are urged to develop a high-throughput screening method for the detection of CYN in water. Construction of low cost, rapid, and sensitive analytical methods for the detection of CYN is challenging. Here, we used graphene oxide (GO) as the fluorescence sensing platform for probing the high affinity of the short aptamer derived from the wild-type long aptamer-CYN sensing. The biosensor construction involved two steps: first, quenching the fluorescence of fluorescent-labelled truncated aptamer using GO as a quencher and, second, fluorescence recovery in the presence of CYN by competitive binding between the target and GO. One of the truncate aptamers has a 12-fold higher affinity and enhances sensitivity compared to the long aptamer sequence. The limit of detection of the high affinity truncated aptamer is 17 pM which is 6-fold lower than the long aptamer (100 pM). The sensor specifically detects CYN in the presence of other potential interfering toxins. The performance of the sensor was validated using CYN spiked tap water with very good recovery percentage. A rapid and highly sensitive detection of CYN from water resources has been achieved using this method.

This study presents a quick, low-cost, and easy technique for the detection of norovirus in several food samples, including cucumber, lettuce, and chicken. The developed sandwich immunoassay method depends on employing nanotechnology for the detection step. Lactoferrin immobilized on activated Q-tips cotton swabs was used as a general capturing reagent to bind viruses from the sample surface. The cotton swabs were then submerged in a gold nanoparticle solution, which had previously decorated with a specific antibody for noroviruses. Positive samples retained the red color of the gold nanoparticles on the surface of Q-tips, even after washing, while the negative control samples easily lost their color through washing. The results confirmed that the developed assay has superior sensitivity and selectivity with a LOD between 10 and 53 pfu/mL for all tested samples. In light of the difficulty, complexity, and high cost of the methods recently used for detecting viruses in food samples, this method presents a promising reliable technique that can be employed for the rapid detection of norovirus in food samples with an acceptable accuracy.

The uncontrolled usage of veterinary antibiotics has led to their widespread pollution in waterways and milk products. Potential impact of antibiotic residues on the environment and human health such as increased antibiotic resistance of microorganisms and triggering allergic reactions in humans have been reported. In this work, we developed a highly selective and sensitive voltammetric aptasensor for on-step, sensitive and low cost detection of azlocillin antibiotic, one of the broad spectrum β-lactam antibiotics. The successful selection of DNA aptamers against azlocillin was accomplished using systemic evolution of ligands by exponential enrichment (SELEX) method. Fluorescence-binding assays showed dissociation constant of 55 nM for one of the selected aptamers (Az9). This aptamer was used to construct a competitive voltammetric aptasensor for azlocillin. A limit of detection of 1.2 pg/mL as well as remarkable selectivity against potential interfering agents, including amoxicillin, were achieved. This signal-off competitive sensor takes 30–50 min to complete the quantification of the target antibiotic. The sensor was challenged by detecting the target directly in complex environments such as tap and waste water where good recovery percentages were achieved.

Aptamers have received considerable attention due to their numerous advantages as biorecognition receptors. However, the tediousness and high cost of the conventional selection process of aptamers remain major challenges that limit their widespread use. To overcome these limitations, here we designed a new electrochemical SELEX platform that enables a rapid, efficient, and cost-effective enrichment method for the identification of aptamers, particularly against small molecules. The selection platform is based on the immobilization of the target analyte on gold electrodes that leads to improved selection efficiency and enables in situ monitoring of the enriched DNA using square-wave voltammetry. Compared with the conventional SELEX method, this selection protocol avoids the use of beads as a solid matrix and fluorescently labeled DNA, which is usually required for small molecules, thus offering simplified aptamer/target incubation, washing, and elution steps. Moreover, the DNA recovery can be detected by simply measuring the current of the electrodes in a ferro/ferricyanide redox couple. This would eliminate the need for fluorescence labeling, which significantly reduces the cost of the procedure. The approach was successfully applied for the selection of high-affinity aptamers that bind specifically to the small molecule 11-deoxycortisol hormone using eight rounds. One of the selected aptamers that showed a dissociation constant at the subnanomolar level was used to construct a competitive voltammetric aptasensor exhibiting high sensitivity, selectivity against other steroid analogues, and possible applicability in serum samples. Thus this SELEX approach offers great promise for a faster, simpler, and more economic aptamer identification method for various targets including small molecules for a wide variety of applications.

© 2021 The Royal Society of Chemistry.This study demonstrates the development of a sensitive, specific, and quantitative peptide-based nanoprobe prototype assay for the detection of Legionellaceae in a simple way and in a short time. In this work, proteases present in the culture supernatants of Legionella spp. were used as a biomarker. Fluorogenic peptide substrates, specific to Legionella strains culture supernatant proteases, were identified. Peptidases produced a significant increase in the fluorescence intensity following the cleavage of the dipeptide fluorogenic substrates. The specific substrates were identified and coupled with carboxyl-terminated nano-magnetic particles (NMPs). On the other hand, the C-terminal was conjugated with the cysteine residue to covalently integrate with a gold sensing platform via the Au-S linkage. Four different sensors were fabricated from the four specific substrates, which were treated with the protesase of six different species of Legionella. In the presence of specific protease, the peptide sequence is digested and the magnetic nanobeads moved out of the gold surface, resulting in the apparence of gold color. One of the nanoprobes sensitivity detects as low as 60 CFU mL-1 of Legionella anisa, Legionella micdadei, and Fluoribacter dumoffii. The cross-reactivity of the sensors was tested using other closely associated bacterial species and no significant cross-reactivity of the sensors was found. It is envisaged that this assay could be useful for screening purposes or might be supportive for the fast and easy detection of Legionella protease activity for water monitoring purposes.

The novel corona (SARS-CoV-2) virus causes a global pandemic, which motivates researchers to develop reliable and effective methods for screening and detection of SARS-CoV-2. Though there are several methods available for the diagnosis of SARS-CoV-2 such as RT-PCR and ELSIA, nevertheless, these methods are time-consuming and may not apply at the point of care. In this study, we have developed a specific, sensitive, quantitative and fast detection method for SARS-CoV-2 by fluorescence resonance energy transfer (FRET) assay. The total extracellular protease proteolytic activity from the virus has been used as the biomarker. The specific peptide sequences from the library of 115 dipeptides were identified via changes in the fluorescence signal. The fluorogenic dipeptide substrates have the fluorophore and a quencher at the N- and the C- terminals, respectively. When the protease hydrolyzes the peptide bond between the two specific amino acids, it leads to a significant increase in the fluorescence signals. The specific fluorogenic peptide (H-d) produces a high fluorescence signal. A calibration plot was obtained from the changes in the fluorescence intensity against the different concentrations of the viral protease. The lowest limit of detection of this method was 9.7 ± 3 pfu/mL. The cross-reactivity of the SARS-CoV-2-specific peptide was tested against the MERS-CoV which does not affect the fluorescence signal. A significant change in the fluorescence signal with patient samples indicates that this FRET-based assay might be applied for the diagnosis of SARS-CoV-2 patients. Graphical abstract.

The timely diagnosis of MRSA in clinical samples helps to reduce the attendant morbidity/mortality associated with infection due to the organism. The early institution of appropriate therapy or deployment of infection control protocols are dependent on a timely report from the microbiology laboratory. Various assays currently used in the identification of MRSA are associated with inherent shortcomings, thus there is a need to explore newer diagnostic frontiers that can eliminate some of these short comings at a relatively cheap, timely, specific and sensitive manner. We present in this study a MRSA specific optical immunosensor to detect the presence of the pathogen on contaminated surface using control and patient strains. Results revealed a detection limits of 103 CFU mL-1 upon visual observation, and 29 CFU mL-1 as determined by the linear regression equation, following the use of ImageJ to quantify activated cotton swab color intensity. The specificity of the sensor was examined by blind testing a panel of non-MRSA bacteria (E. coli, S. aureus and S. epidermis). Negative visual read-out was observed for all tested non-specific bacteria except for MRSA. Assay takes an average of 5 min and presents a powerful point-of-care diagnostic platform for the detection of MRSA.

Aptamers are single-stranded DNA or RNA, which have attracted considerable scientific interest due to their characteristic of specific and selective binding to target molecules. They are evolved from the in vitro process known as systematic evolution of ligands by exponential enrichment (SELEX). This paper reports a simple experimental approach to elucidate the binding region of small targets binding aptamers. A previously isolated 60-mer aptamer for the anti-coagulant dabigatran etexilate (DBG) was used for this investigation. Complimentary sequences labelled with a fluorophore and a quencher were used for testing the binding region by change in the fluorescence signal. The full-length aptamer was truncated to multiple shorter copies including a 38 nucleotides sequence that showed 47 fold high affinity compared to the original aptamer. Circular dichroism spectroscopy (CD) measurements indicate that the 38-mer is remarkably more sensitive than the parent aptamer. The truncated 38-mer sequence was used to construct a turn-on fluorescence sensor with the detection limit of 1 nM. The performance of the sensor was examined in blood serum samples and showed excellent recovery percentages exceeding 98%. The reported screening protocol could be applied to the growing small targets aptasensors that require efficient binding aptamer sequences coupled with optimum signal transduction methods.

Dabigatran etexilate (DBG) is a new anticoagulant drug (commercially sold under the names Pradaxa® and Pradax™) that replaces Warfarin, the landmark agent for anticoagulation therapy. Inadequate administration of DBG or in the cases of massive bleeding that occurs after renal impairment, DBG therapy can carry a substantial life-threatening risks. One of the major limitations of DBG treatment is the lack of a simple and quick tool for measuring its level in blood in the case of massive bleedings or emergency operations. In this work, we have incorporated a previously isolated aptamer for DBG to develop a simple competitive lateral flow aptasensor (LFA) for the determination of DBG in buffer and blood samples. A full-length 60-mer aptamer as well as a truncated 38-mer aptamer were conjugated to gold nanoparticles (AuNPs) via thiol-Au coupling chemistry. After appropriate AuNP surface passivation steps, the aptamer's core region was hybridized with 8-mer biotinylated sequences. The conjugated particles could be capture on the test line by the interaction of the biotin molecules with a previously deposited streptavidin. Incubation of the conjugated particles with DBG causes the aptamer to undergo a conformational change that releases the 8-mer biotinylated sequences and result in the disappearance of the test line. Lysozyme protein was used to construct the control line that non-specifically interacts with the conjugated particles whether or not the target compound is present. The developed LFA achieves 20 nM detection level in buffer and blood samples, operates within the nanomolar range, and shows excellent selectivity against potential interfering molecules. The developed sensor could help assessing the levels of DBG in medical conditions that require rapid interventions.

Aptamers have shown a number of potential applications in sensing and therapeutic due to the high affinity and specificity towards their target molecules. Not all the nucleotides in the full length aptamers are involved in the binding with their targets. The non-binding domain of the aptamer may affect the binding affinity of the aptamer-target complex. Mapping the aptamer binding region could increase the affinity and the specificity. In this paper, we designed aptamer-based fluorescence sensors from a truncated progesterone (P4) aptamer. Then, fluorescein and quencher labelled aptamer complementary oligonucleotide sequences were hybridized to the truncated aptamer at different sites to form duplex structures. We used fluorescence-quencher pair displacement assay upon progesterone binding for the determination of P4. One of the truncated sequences has shown high binding affinity with 16 fold increase in the dissociation constant, Kd (2.1 nM) compared to the original aptamer. The aptasensor was highly selective for P4 against similar compounds such as 17-β estradiol, bisphenol-A and vitamin D. The sensor has been applied for the detection of P4 in spiked tap water and in urine samples showing good recovery. This new developed aptamer-based fluorescence biosensor can be applied in food, pharmaceutical, and clinical industries.

Liver cancer is one of the most widely spread cancers in the world. Cancer stem cells (CSCs) are a small subpopulation of liver cancer cells that are thought to be responsible for relapse of cancer and the resistance to chemotherapy. Detection of CSCs is highly demanded for screening patients who are at high risk for developing metastatic cancers. However, the current methodologies for CSCs detection are sophisticated, expensive and not reliable. Here, we report the development of a label-free impedance immunosensors for liver CSC quantification using four established CSC surface biomarkers (CD44, CD90, CD133/2 and OV-6). The immunosensors were simply fabricated by the covalent attachment of four biomarkers specific antibodies on gold electrodes using cysteamine/phenylene isothiocyanate linker. Electrochemical impedance spectroscopy was employed to detect the binding of the cells to the immunosensors. The binding of the CSCs to the gold electrode surface retards the access of ferri-ferrocyanide redox molecules to the electrode leading to enhancement in the charge transfer resistance (Rct) which represents the basis of the detection signal. The developed electrochemical immunosensors showed high sensitivity and selectivity for CSC detection with a wide linear range from 1 × 101 to 1× 104 cells/mL with a limit of detection of 1 cell/ml. This work represents a new, accurate, simple and low cost method for the detection of liver CSC that might help in the early diagnosis of metastatic disease and cancer relapse.

The autosomal recessive-hyper immunoglobulin E syndromes (AR-HIES) are inherited inborn primary immunodeficiency disorders caused mainly by mutations in the dedicator of cytokinesis 8 (DOCK8) gene. A method is described for the selection of DNA aptamers against DOCK8 protein. The selection was performed by using a gold electrode as the solid matrix for immobilization of DOCK8. This enables voltammetric monitoring of the bound DNA after each selection cycle. After eight rounds of selection, high affinity DNA aptamers for DOCK8 were identified with dissociation constants (Kds) ranging from 3.3 to 66 nM. The aptamer which a Kd of 8.8 nM was used in an aptasensor. A gold electrode was modified by self-assembly of the thiolated aptamer, and the response to the DOCK8 protein was detected by monitoring the change in the electron transfer resistance using the ferro/ferricyanide system as a redox probe. The aptasensor works in the 100 pg.mL−1 to 100 ng.mL−1 DOCK8 concentration range, has a detection limit of 81 pg.mL−1 and good selectivity over other proteins in the serum.

An electrochemical aptasensor is described for determination of the phytohormone of zearalenone (ZEA). The gold electrode was modified with ZEA via covalent attachment using cysteamine-hydrochloride and 1,4-phenylene diisocyanate linker. A truncated ZEA aptamer with a dissociation constant of 13.4 ± 2.1 nM was used in an aptasensor. The electrochemical property was investigated using square wave voltammetry for monitoring the change in the electron transfer using the ferro/ferricyanide system as redox probe. Under optimal experimental conditions, the response was best measured at a potential of 0.20 V (vs. Ag/AgCl). The signals depended on the competitive mechanism between the immobilised ZEA and free ZEA for the aptamer binding site. The aptasensor works in the range 0.01 to 1000 ng·mL−1 ZEA concentration, with a detection limit of 0.017 ng·mL−1. High degree of cross-reactivity with the other analogues of ZEA was observed, whereas none towards other mycotoxins. The aptasensor was further applied for the determination of ZEA in the extract of maize grain and showed good recovery percentages between 87 and 110%.

Okadaic acid (OKA), a marine toxin produced by dinoflagellates, is responsible for most human diarrhetic shellfish poisoning-associated health disorders. A competitive displacement assay for OKA is described here. An OKA-binding aptamer was truncated with two sequences, one labeled with 6-carboxyfluorescein (FAM), and one with a quencher. On addition of OKA, it will bind to the aptamer and green fluorescence pops up because label and quencher become spatially separated. One of the truncated aptamers exhibis an excellent binding capability (Kd 2.77 nM) for OKA compared to its full-length aptamer (526 nM). The selectivity of the assay was proven by the successful fluorometric determination of OKA in the presence of common diarrhoetic toxins and in shellfish extracts. The detection limit is as low as 39 pg·mL−1.

Osteoporosis (OP) is a bone disease involved in dysregulation of one of the bone metabolism arms, formation, or desorption cause a porous bone. Osteocalcin (OC) and beta-crosslap (BC), are the well-known markers for OP, which are connected to bone formation and desorption, respectively. In addition to the OP biomarker, BC is also used as an estrogen replacement therapeutic monitoring. ELISA and other antibody-based detection methods are routinely used for measuring OC and BC. These methods have limitations that include thermostability, sensitivity, sacrificing animals, and cost of production. However, aptamer-based-assays are of interest to overcome these drawbacks and achieve the most specific and robust application. Herein, specific aptamers for OC and BC were selected by the systematic evolution of ligands by exponential enrichment (SELEX) method from the pool of ssDNA library with 60 random sequences. The binding affinity (Kd) of the selected aptamers were evaluated against the respective biomarkers. The high-affinity aptamers of OC and BC showed the Kd values of 59 and 55 nM respectively. A graphene oxide-based aptasensors were fabricated from the high-affinity aptamers, and the detection limits of OC and BC were found to be 0.4 pg/ml and 0.21 pg/ml, respectively. These aptasensors have been tested with OC and BC spiked buffer samples and validated using serum samples collected from osteoporotic rats.

Mastitis in dairy cattle is an inflammatory reaction of the udder tissue. Mastitis increases plasmin levels, leading to an increased proteolysis of milk proteins such as casein, resulting in a significant decrease in milk quality and related dairy products. Due to its key-role in mastitis, we used plasmin proteolytic activity as a biomarker for the detection of mastitis in bovine mastitic milk. Inspired by earlier studies on protease activity using mastitic milk samples, we developed a simple colorimetric assay to distinguish mastitic milk from milk derived from healthy animals. The plasmin substrate coupled to magnetic nanoparticles form a black self-assembled monolayer on a gold sensor surface. In the presence of increased levels of plasmin, the substrate is cleaved and the peptide fragment attached to the magnetic beads, will be attracted by the magnet which is present under the sensor strips revealing the golden surface. We found the area of the golden color surface proportional to plasmin activity. The sensitivity of this method was determined to be 1 ng/ml of plasmin in vitro. Next, we tested the biosensor using mastitis positive milk of which infection is confirmed by bacterial cultures. This newly developed colorimetric biosensor has high potential in applications for the diagnosis of mastitis with potential spin offs to health, food and environmental sectors.

Foodborne diseases is a major public health concern and costs billions of dollars losses every year. For example, 93.8 million cases of gastroenteritis reported in Europe, United States, South America and Asia. Different methods depending on various scientific principles are used for detection of pathogenic bacteria relating foodborne diseases, conventional methods including culture-depending methods, microscopic, PCR, serological and biochemical methods are still used but majority of this methods suffers from a number of disadvantages includes long time-analysis, high cost, limited sensitivity and lab-based. Therefore, there is an urgent need for development of rapid screening assays for field applications with high sensitivity. In this study, we developed colorimetric immuno-sensor was developed and evaluated as a novel rapid detection nanosensing platform for the detection of foodborne pathogens such as Salmonella Typhimurium, Salmonella Enteritidis, Staphylococcus Aureus and Campylobacter Jejuni. The sensing platform composed of cotton swab and nanoparticles. Cotton swaps were functionalized with general or specific recognition receptors for collecting and pre-concentration of bacteria from the surfaces. Then the cotton swab was dipped in a developing solution to indicate the presence of specific bacteria. The developing solution has a cocktail of different coloured nanospheres conjugated with different recognition receptors for the various bacteria analytes was used to generate the different colours. The nanosensor was used for testing the bacteria on different surfaces mimicking the poultry processing units such as glass slides, stainless steel and chicken meat.

The development of a sensitive and rapid detection approach for allergens in various food matrices is essential to assist patients in managing their allergies. The most common methods used for allergen detection are based on immunoassays, PCR and mass spectrometry. However, all of them are very complex and time-consuming. Herein, an aptamer biosensor for the detection of the major shrimp allergen tropomyosin (TM) was developed. Graphene oxide (GO) was used as a platform for screening of the minimal-length aptamer sequence required for high-affinity target binding. A fluorescein dye labeled GO quenches the truncated aptamer by π-stacking interactions. After the addition of TM, the fluorescence was restored due to the competitive binding of the aptamer to GO. One of the truncated aptamers was found to bind to TM with four-fold higher affinity (30 nM) compared to the full-length aptamer (124 nM), with a limit of detection (LOD) of 2 nM. The aptamer-based sensor demonstrates the sensitive, selective, and specific detection of TM in 30 min. The performance of the sensor was confirmed using TM spiked chicken soup, resulting in a high percentage recovery (~97 ± 10%). The association of GO and labelled aptamer sensor platform has shown the rapid detection of TM in food, which is compared to other methods very sensitive, specific and performs in high throughput application.

The high-affinity region of a truncated aptamer was applied to the development of a sensitive method for the determination of microcystin-LR (MC-LR) using competitive displacement and molecular beacons. In this assay, the fluorophore and quencher labelled complementary sequences of the aptamer are hybridized with the truncated aptamer to form a fluorophore-quencher pair. In the presence of MC-LR, the aptamer duplex dissociates, and the fluorophore-quencher pair is separated. This turn leads to an increase in the yellow fluorescence which is best measured at excitation/emission wavelengths of 555/580 nm. One of the truncated aptamers showed a 50-fold increase in the affinity (0.93 nM) compared to the wild type aptamer (50 nM). The truncated sequence shows considerable cross-reactivity with L congeners but none with other congeners. The assay works in 0.5 to 200 nM MC-LR concentration range. It was applied to spiked tap water samples and gave recoveries around 95 ± 5%. Graphical abstract Schematic representation of a method for determination of microcystin-LR via fluorescence that is induced by competitive displacement of complementary DNA strands in a truncated dsDNA aptamer.

MicroRNA (miRNA) is a small non-coding RNA with the size of 18–22 nucleotide. MiRNAs play a major role in the gene expression and regulation. They influence more than 50% of protein coding genes in mammalian genome which regulate many cellular functions. Their dysregulation can lead to cancer and other diseases. MiRNAs have been shown to be associated with breast cancers. Previously q-PCR based assays have been used successfully for detection and quantification of miRNAs, however, these assays are expensive and cumbersome. Here, we report the detection of few breast cancer microRNA sequences using fluorescence displacement assay. The assay employed a fluorophore-quencher pair by hybridization of fluorescently labelled cDNA of miRNA and a quencher labelled short DNA. Upon hybridization, the fluorophore and the quencher become in close vicinity to each other leading to significant fluorescence quenching. In the presence of target miRNA, the fluorophore and quencher are separated due to the duplex dissociation and form stable cDNA-miRNA double strand which leads to increase in the fluorescence intensity. The assay has dynamic range from 0.2 to 250 nM miRNA concentration. We could detect miRNA as low as 1 pM level. The method was applied to detect the miRNA spiked to the total RNA extracted from whole blood. The fluorescence based method has been validated using standard Q-PCR method. This could prove a promising method for the detection of miRNAs.

Cotton swab is the conventional swabbing tool that is usually applied for collecting pathogens from contaminated surfaces, followed by cells lysis and DNA extraction before subjecting to genetic analysis. However, such an approach is time consuming as it involves several steps and requires highly trained personnel to perform the experiment. In this study, we developed a new cotton swab-based detection system that involved integrating bacterial collection, preconcentration and detection on Q-tips. The platform is based on a sandwich assay that can detect different pathogens visually by color changes. Lactoferrin-immobilized cotton is used as a general capturing tool to collect various pathogens from surfaces. The presence of particular bacteria is then detected by immersing the cotton in antibodies attached to different colored nanobeads. The target cell is captured between the lactoferrin and specific antibody-conjugated beads which results in certain color development. The effectiveness of this simply fabricated sensor was demonstrated using Salmonella typhimurium, Salmonella enteritidis, Staphylococcus aureus and Campylobacter jejuni. The intensity of the color on the cotton surfaces increased with increasing the concentration of the pathogenic bacteria. The detection limit was as low as 10 cfu/ml for Salmonella typhimurium and Campylobacter jejuni, 100 cfu/ml for Salmonella enteritidis and 100 cfu/ml for Staphylococcus aureus on chicken meat surface. Moreover, this method showed high selectivity and was further confirmed by loop-mediated isothermal amplification (LAMP). The simplicity and the low cost of this colorimetric sensor renders it applicable to a wide range of other pathogens on different surfaces.

Lung cancer is undoubtedly one of the most serious health issues of the 21 st century. It is the second leading cause of cancer-related deaths in both men and women worldwide, accounting for about 1.5 million deaths annually. Despite advances in the treatment of lung cancer with new pharmaceutical products and technological improvements, morbidity and mortality rates remains a significant challenge for the cancer biologists and oncologists. The vast majority of lung cancer patients present with advanced-stage of pathological process that ultimately leads to poor prognosis and a five-year survival rate less than 20%. Early and accurate screening and analysis using cost-effective means are urgently needed to effectively diagnose the disease, improve the survival rate or to reduce mortality and morbidity associated with lung cancer patients. Thus, the only hope for early recognition of risk factors and timely diagnosis and treatment of lung cancer is biosensors technology. Novel biosensing based diagnostics approaches for predicting metastatic risks are likely to have significant therapeutic and clinical impact in the near future. This article systematically provides a brief overview of various biosensing platforms for identification of lung cancer disease biomarkers, with a specific focus on recent advancements in electrochemical and optical biosensors, analytical performances of different biosensors, challenges and further research opportunities for routine clinical analysis.

Dabigatran Etexilate (PRADAXA) is a new oral anticoagulant increasingly used for a number of blood thrombosis conditions, prevention of strokes and systemic emboli among patients with atrial fibrillation. It provides safe and adequate anticoagulation for prevention and treatment of thrombus in several clinical settings. However, anticoagulation therapy can be associated with an increased risk of bleeding. There is a lack of specific laboratory tests to determine the level of this drug in blood. This is considered the most important obstacles of using this medication, particularly for patients with trauma, drug toxicity, in urgent need for surgical interventions or uncontrolled bleeding. In this work, we performed Systematic evolution of ligands by exponential enrichment (SELEX) to select specific DNA aptamers against dabigatran etexilate. Following multiple rounds of selection and enrichment with a randomized 60-mer DNA library, specific DNA aptamers for dabigatran were selected. We investigated the affinity and specificity of generated aptamers to the drug showing dissociation constants (Kd) ranging from 46.8���208 nM. The most sensitive aptamer sequence was selected and applied in an electrochemical biosensor to successfully achieve 0. 01 ng/ml level of detection of the target drug. With further improvement of the assay and optimization, these aptamers would replace conventional antibodies for developing detection assays in the near future.Dabigatran Etexilate (PRADAXA) is a new oral anticoagulant increasingly used for a number of blood thrombosis conditions, prevention of strokes and systemic emboli among patients with atrial fibrillation. It provides safe and adequate anticoagulation for prevention and treatment of thrombus in several clinical settings. However, anticoagulation therapy can be associated with an increased risk of bleeding. There is a lack of specific laboratory tests to determine the level of this drug in blood. This is considered the most important obstacles of using this medication, particularly for patients with trauma, drug toxicity, in urgent need for surgical interventions or uncontrolled bleeding. In this work, we performed Systematic evolution of ligands by exponential enrichment (SELEX) to select specific DNA aptamers against dabigatran etexilate. Following multiple rounds of selection and enrichment with a randomized 60-mer DNA library, specific DNA aptamers for dabigatran were selected. We investigated the affinity and specificity of generated aptamers to the drug showing dissociation constants (Kd) ranging from 46.8���208 nM. The most sensitive aptamer sequence was selected and applied in an electrochemical biosensor to successfully achieve 0. 01 ng/ml level of detection of the target drug. With further improvement of the assay and optimization, these aptamers would replace conventional antibodies for developing detection assays in the near future.

The work describes a simple cotton swab-based colorimetric immunoassay as a rapid screening tool for pathogenic bacteria on poultry processing plants. This immunosensing platform can be used for the detection of pathogens present on surfaces such as glass, stainless steel and chicken meat. Unlike the reported assays, here, cotton swab plays dual function: as a sample collector from the solid surfaces and as detection platform. The immunoassay was tested for the detection of 4 different bacteria; Salmonella typhimurium, Salmonella enteritidis, Staphylococcus aureus and Campylobacter jejuni. The immunoassays were fabricated by immobilizing specific antibody for each bacterium on a cotton swab that is used to recover the cells from contaminated surfaces. Then, a sandwich immunoassay was developed by immersing the cotton swab in different colored nanobead-conjugated antibody solutions which corresponds to different bacteria. The immunoassays response was detected colorimetrically by following the change in the color intensity produced by the nanobeads due to the specific binding on the cotton swab. This simple colorimetric assay is very sensitive with a detection limit of 10 cfu.mL−1. Furthermore, no significant cross reactivity of the immunoassays with non specific bacteria was observed indicating good selectivity of the immunoassays. This simple, disposable and easy-to- use colorimetric platform shows great promise as rapid qualitative and semi quantitative detection tool for microorganisms on food processing plants and other surfaces.

Liver cancer is considered the fifth most common cancers in the world and the second cause of cancer death in men. Cancer stem cells (CSCs) are a small subset of cancer cells that have been recently proposed to be responsible for tumor relapse, metastasis, and chemoresistance. Here, we report the development of label-free electrochemical immunosensors for CSC detection using four cell surface biomarkers (CD44, CD90, CD133/2 and OV-6). The immunosensors were fabricated by covalent immobilization of the four specific antibodies for the biomarkers on gold electrodes via cysteamine/phenylene isothiocyanate linker. Electrochemical impedance spectroscopy was utilised to monitor the binding of the CSCs to the immunosensors. The binding of the cells to the electrode surface blocks the electron transfer between [Fe(CN)6]3-/4− redox probe and the gold electrode causing an increase in the charge transfer resistance (Rct). This change in the Rct represents the basis of the CSC biosensing. The developed immunosensors showed high sensitivity and selectivity for CSC detection with a wide dynamic range from 1 × 101 to 1× 106 cells/mL. This work opens up new, accurate, simple and low cost avenue for the detection of liver CSC that might help in the early diagnosis and treatment of liver cancer.

The work describes a fluorescence-based study for mapping the highest affinity truncated aptamer from the full length sequence and its integration in a graphene oxide platform for the detection of Salmonella enteriditis. To identify the best truncated sequence, molecular beacons and a displacement assay design are applied. In the fluorescence displacement assay, the truncated aptamer was hybridized with fluorescein and quencher-labeled complementary sequences to form a fluorescence/quencher pair. In the presence of S. enteritidis, the aptamer dissociates from the complementary labeled oligonucleotides and thus, the fluorescein/quencher pair becomes physically separated. This leads to an increase in fluorescence intensity. One of the truncated aptamers identified has a 2-fold lower dissociation constant (3.2 nM) compared to its full length aptamer (6.3 nM). The truncated aptamer selected in this process was used to develop a fluorometric graphene oxide (GO) based assay. If fluorescein-labeled aptamer is adsorbed on GO via π stacking interaction, fluorescence is quenched. However, in the presence of target (S. enteriditis), the labeled aptamers is released from surface to form a stable complex with the bacteria and fluorescence is restored, depending on the quantity of bacteria being present. The resulting assay has an unsurpassed detection limit of 25 cfu·mL−1 in the best case. The cross reactivity to Salmonella typhimurium, Staphylococcus aureus and Escherichia coli is negligible. The assay was applied to analyze doped milk samples for and gave good recovery. Thus, we believe that the truncated aptamer/graphene oxide platform is a potential tool for the detection of S. Enteritidis.

Food allergy is considered one of the major health issues nowadays that affects millions of people worldwide, especially in industrial countries. Studies have shown that food allergy affects about 4" of the adult population and a higher prevalence amongst children (6-8") was reported. Different analytical methods are currently used for allergens detection such as Enzyme-Linked Immunosorbent Assays (ELISA), enzyme-linked immunoaffinity chromatography, HPLC (High-Performance Liquid Chromatography) and capillary electrophoresis methods with size-exclusion chromatography and laser-induced fluorescence detection. Protein-based methods such as western blot and immunoperoxidase staining are also utilized. This chapter discusses several aspects of biosensor developments for allergen monitoring and allergy diagnosis and reviews the recent achievements in the allergen detection. It then describes the integration of bionanotechnology to the biosensor devices. Electrochemical biosensors are more favourable as they can meet market demands for fabrication of compact, portable and low-cost devices.

The efficiency of current microcystin detection methods has been hampered by the low detection limits required in drinking water and that routine detection is restricted to a few of the congeners with high degree of undesired cross-reactivity. Here, we report the development of novel microcystin-targeting molecules and their application in microcystin detection. We have selected DNA aptamers from a diverse random library that exhibit high affinity and specificity to microcystin-LR, -YR, and -LA. We obtained aptamers that bind to all chosen congeners with high affinity with K(D) ranging from 28 to 60 nM. More importantly, we also obtained aptamers that are selective among the different congeners, with selectivity from 3-folds difference in binding affinity to total discrimination (K(D) of 50 nM versus nonspecific binding). Electrochemical aptasensors constructed with the selected aptamers were able to achieve sensitive and congener-specific microcystin detection with detection limit as low as 10 pM.

The Bacillus subtilis lysC lysine riboswitch modulates its own gene expression upon lysine binding through a transcription attenuation mechanism. The riboswitch aptamer is organized around a single five-way junction that provides the scaffold for two long-range tertiary interactions (loop L2-loop L3 and helix P2-loop L4)--all of this for the creation of a specific lysine binding site. We have determined that the interaction P2-L4 is particularly important for the organization of the ligand-binding site and for the riboswitch transcription attenuation control. Moreover, we have observed that a folding synergy between L2-L3 and P2-L4 allows both interactions to fold at lower magnesium ion concentrations. The P2-L4 interaction is also critical for the close juxtaposition involving stems P1 and P5. This is facilitated by the presence of lysine, suggesting an active role of the ligand in the folding transition. We also show that a previously uncharacterized stem-loop located in the expression platform is highly important for the riboswitch activity. Thus, folding elements located in the aptamer and the expression platform both influence the lysine riboswitch gene regulation.